Simon Glass [Sat, 24 Aug 2019 13:23:04 +0000 (07:23 -0600)]
binman: Increase size of TPL and SPL test data
At present these are large enough to hold 20 bytes of symbol data. Add
four more bytes so we can add another test.
Unfortunately at present this involves changing a few test files to make
room. We could adjust the test files to not specify sizes for entries.
Then we could make the tests check the actual sizes. But for now, leave it
as it is, since the effort is minor.
Simon Glass [Sat, 24 Aug 2019 13:23:03 +0000 (07:23 -0600)]
binman: Avoid needing the section size in advance
Entries which include a section and need to obtain its contents call
GetData(), as with any other entry. But the current implementation of this
method in entry_Section requires the size of the section to be known. If
it is unknown, an error is produced, since size is None:
TypeError: can't multiply sequence by non-int of type 'NoneType'
There is no need to know the size in advance since the code can be
adjusted to build up the section piece by piece, instead of patching each
entry into an existing bytearray.
Simon Glass [Sat, 24 Aug 2019 13:23:00 +0000 (07:23 -0600)]
binman: Allow symbols to be resolved inside sections
At present we only support symbols inside binaries which are at the top
level of an image. This restrictions seems unreasonable since more complex
images may want to group binaries within different sections.
Relax the restriction, adding a new _SetupTplElf() helper function.
Simon Glass [Sat, 24 Aug 2019 13:22:54 +0000 (07:22 -0600)]
binman: Use the Makefile for u_boot_ucode_ptr
Remove this file from git and instead build it using the Makefile.
Update tools.GetInputFilename() to support reading files from an absolute
path, so that we can read the Elf test files easily. Also make sure that
the temp directory is report in ELF tests as this was commented out.
Simon Glass [Sat, 24 Aug 2019 13:22:53 +0000 (07:22 -0600)]
binman: Use the Makefile to build ELF test files
At present the ELF test files are checked into the U-Boot tree. This is
covenient since the files never change and can be used on non-x86
platforms. However it is not good practice to check in binaries and in
this case it does not seem essential.
Update the binman test-file Makefile to support having source in a
different directory. Adjust binman to run it to build bss_data, as a
start. We can add other files as needed.
Simon Glass [Sat, 24 Aug 2019 13:22:51 +0000 (07:22 -0600)]
binman: Fix IFWI output when using an Intel FIT image
At present this entry does not work correctly when a FIT image is used as
the input. It updates the FIT instead of the output image. The test passed
because the FIT image happened to have the right data already.
Simon Glass [Sat, 24 Aug 2019 13:22:50 +0000 (07:22 -0600)]
binman: Add support for Intel FIT
A Firmware Image Table (FIT) is a data structure defined by Intel which
contains information about various things needed by the SoC, such as
microcode.
Add support for this entry as well as the pointer to it. The contents of
FIT are fixed at present. Future work is needed to support adding
microcode, etc.
Simon Glass [Sat, 24 Aug 2019 13:22:49 +0000 (07:22 -0600)]
binman: x86: Separate out 16-bit reset and init code
At present these two sections of code are linked together into a single
2KB chunk in a single file. Some Intel SoCs like to have a FIT (Firmware
Interface Table) in the ROM and the pointer for this needs to go at
0xffffffc0 which is in the middle of these two sections.
Make use of the new 'reset' entry and change the existing 16-bit entry to
include just the 16-bit data.
Simon Glass [Sat, 24 Aug 2019 13:22:48 +0000 (07:22 -0600)]
binman: Add support for an x86 'reset' section
At present binman has a single entry type for the 16-bit code code needed
to start up an x86 processor. This entry is intended to include both the
reset vector itself as well as the code to move to 32-bit mode.
However this is not very flexible since in some cases other data needs to
be included at the top of the SPI flash, in between these two pieces. For
example Intel requires that a FIT (Firmware Image Table) pointer be placed
0x40 bytes before the end of the ROM.
To deal with this, add a new reset entry for just the reset vector. A
subsequent change will adjust the existing 'start16' entry.
Simon Glass [Sat, 24 Aug 2019 13:22:47 +0000 (07:22 -0600)]
binman: Correct use of 'replace' in IFWI tests
At present the Intel IFWI entry uses 'replace' without the 'ifwi-' prefix.
This is a fairly generic name which might conflict with the main Entry
base class at some point, if more features are added. Add a prefix.
Simon Glass [Sat, 24 Aug 2019 13:22:43 +0000 (07:22 -0600)]
binman: Use cls instead of self for class methods
It is more common to use the name 'cls' for the class object of a class
method, to distinguish it from normal methods, which use 'self' Update the
binman tests accordingly.
Simon Glass [Sat, 24 Aug 2019 13:22:42 +0000 (07:22 -0600)]
patman: Update command.Run() to handle failure better
At present tools are not expected to fail. If they do an exception is
raised but there is no detail about what went wrong. This makes it hard
to debug if something does actually go wrong.
Fix this by outputting both stderr and stdout on failure.
- logicpd pinmux
- i.MX7ULP: imx_ddr_size
- fixes Toradex i.MX6/i.MX7
- pico-imx7d
- tpc70 converted to DM
- New Board: meerkat96
- add HAB version command
- i.MX8 :
imx8: Jump from alias to OCRAM address at SPL init
imx8qm/qxp: Set SPL TEXT base to OCRAM base
Tom Rini [Mon, 14 Oct 2019 11:28:32 +0000 (07:28 -0400)]
Merge tag 'mmc-10-10-2019' of https://gitlab.denx.de/u-boot/custodians/u-boot-mmc
- Add sdhci driver for Broadcom iProc platform
- Add a driver callback for power-cycle for mmc
- Implement host_power_cycle callback for stm32_sdmmc2
- spl: dm_mmc: Initialize only the required mmc device
Use imx_ddr_size() to retrieve the total DDR size instead
of passing a hardcoded memory size.
imx_ddr_size() calculates the memory size based on the actual
MMDC registers values and is useful to detect misconfigurations,
so switch to this more robust approach.
Yannick Fertré [Mon, 7 Oct 2019 13:29:09 +0000 (15:29 +0200)]
video: add support of panel RM68200
Support for Raydium RM68200 720p dsi 2dl video mode panel.
This rm68200 panel driver is based on the Linux Kernel driver from
drivers/gpu/drm/panel/panel-raydium-rm68200.c.
Yannick Fertré [Mon, 7 Oct 2019 13:29:05 +0000 (15:29 +0200)]
dm: Add a dsi host uclass
Display Serial Interface (DSI) host can usefully be modelled
as their own uclass.
DSI defines a serial bus and a communication protocol
between the host and the device (panel, bridge).
Igor Opaniuk [Mon, 22 Jul 2019 09:05:06 +0000 (12:05 +0300)]
colibri_imx7: provide proper node name to pmic_get
Implementation of pmic_get() uses uclass_find_device_by_name(), which
behaviour was changed in 4213609cc7
("drivers: core: use strcmp when find device by name"). Now we have to
supply full node name with unit address.
CPU: Freescale i.MX7D rev1.3 1000 MHz (running at 792 MHz)
CPU: Extended Commercial temperature grade (-20C to 105C) at 41C
Reset cause: POR
DRAM: 512 MiB
initcall sequence 9ffd3a4c failed at call 87803c61 (err=-19)
ERROR Please RESET the board
Fixes: 4213609cc7("drivers: core: use strcmp when find device by name") Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Sjoerd Simons [Tue, 18 Jun 2019 20:13:20 +0000 (22:13 +0200)]
spl, Makefile: Take external offset into account for fit images
When building a FIT image for SPL to load also take into account the
configured external offset. This allows the SPL to load the u-boot FIT
image correctly when configuring SECURE_BOOT on i.mx6 is enabled
(with CONFIG_FIT_EXTERNAL_OFFSET=0x3000).
Note this doesn't allow secure booting; but it does allow an unsigned
SPL/u-boot with secure boot support eanbled to boot on open device.
Ye Li [Fri, 12 Jul 2019 09:33:52 +0000 (09:33 +0000)]
imx8: Jump from alias to OCRAM address at SPL init
When running SPL on iMX8, the A core starts at address 0
which is a alias to OCRAM 0x100000.
The alias only map first 96KB of OCRAM, so this require the
SPL size can't beyond 96KB. But when using SPL DM, the size increase
significantly and may exceed 96KB.
So to fix the problem, we will change SPL linker address to OCRAM
address 0x100000. And then jump to the absolute address not the PC relative
address for entering OCRAM.
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Lukasz Majewski [Thu, 10 Oct 2019 14:11:24 +0000 (16:11 +0200)]
imx: tpc70: Add board_boot_order() to distinguish between eMMC and SD boot
The TPC70 can boot from SD card (debug/development) and eMMC (production).
The board_boot_order() function provides a run time check for the device
from which one wants to boot (it is selected by GPIO pins setup).
Moreover, a fallback to SD card is provided if the detection is not
possible or working properly.
Adam Ford [Wed, 9 Oct 2019 17:53:57 +0000 (12:53 -0500)]
ARM: imx6q_logic: Remove legacy pinmuxing code from board file.
With the OCRAM expanded to 256KB and the SPL_PINCTRL enabled with
-u-boot.dtsi entries to include the pinmuxing in SPL, the manual
code setting up the pinmux can go away.
This patch removes the legacy pinmuxing code from the board file.
Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Adam Ford [Wed, 9 Oct 2019 17:53:56 +0000 (12:53 -0500)]
ARM: imx6q_logic: Enable Pin muxing in SPL
With the 256KB of OCRAM available to SPL now, there should be
enough room to enable the pinmuxing in SPL from the device tree.
This patch enables SPL_PINCTRL et al and adds the serial and
usdhc pin mux references to the -u-boot.dtsi file so the pins can be
configured from the device tree.
Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Adam Ford [Wed, 9 Oct 2019 17:53:55 +0000 (12:53 -0500)]
ARM: imx6q_logic: Enable 256KB OCRAM
Since this board config only supports, the i.MX6D/i.MX6Q configurations,
256K of on-chip RAM is available which increases the space available
to SPL to help further reduce board code and further enable device tree
functions.
This patch enables 256K of RAM.
Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Sjoerd Simons [Thu, 20 Jun 2019 20:34:35 +0000 (22:34 +0200)]
mx6: mx6sabre common: Use more conventional spelling of fdtfile
Both the distro boot configuration as well as the general pxe support
standardized on fdtfile as the variable to hold the dtb filename.
Adjust to follow that such that e.g. "pxe boot" will just work.
Tom Rini [Fri, 11 Oct 2019 20:28:47 +0000 (16:28 -0400)]
sandbox: Remove sandbox_noblk build
At this point, all drivers that do not use CONFIG_BLK are past their
migration deadlines, so remove this config as it's no longer helpful and
hinders enhancing block drivers.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
This define indicates if DM_SPI shall be supported in SPL. This allows
proper operation of DM converted SPI drivers in SPL, which use
#if !CONFIG_IS_ENABLED(DM_SPI) to also support not yet DM/DTS converted
boards.
If an exception occurs in a loaded image and the relocation offset is
unknown, it is helpful to know the instructions pointed to by the
program counter. This patch adds the missing output.
warnings, because readl and friends are unconditionally defined
earlier in io.h. Moreover, the redefinitions lack the memory barriers
that the first definitions have. So I'm guessing this is practically
dead code.
Mans Rullgard [Tue, 3 Sep 2019 14:16:50 +0000 (16:16 +0200)]
spl: mmc: Add option to set eMMC HW boot partition
This change allows setting pre-defined eMMC boot partition for SPL eMMC
booting. It is necessary in the case when one wants to boot (through falcon
boot) from eMMC after loading SPL from other memory (like SPI-NOR).
Signed-off-by: Mans Rullgard <mans@mansr.com>
[lukma: Edit the commit message] Signed-off-by: Lukasz Majewski <lukma@denx.de> Acked-by: Andreas Dannenberg <dannenberg@ti.com>
Lokesh Vutla [Tue, 1 Oct 2019 05:11:01 +0000 (10:41 +0530)]
arm: dra7xx: Hang on any failure during IOdelay recalibration
If there is any failure during IOdelay recalibration sequence, IOs are
not guaranteed to behave as expected. So hang on any failure during the
sequence.
Lokesh Vutla [Tue, 1 Oct 2019 05:11:00 +0000 (10:41 +0530)]
arm: dra7xx: Fix error path in iodelay recalibration
When an error is reported in __recalibrate_iodelay_start(), de-isolation
of IO doesn't happen. Because of this, undefined behaviour is observed
on many peripherals without any error. So make sure io is out of isolation
at the end of iodelay recalibration.
Reported-by: Richard Woodruff <r-woodruff2@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
arm: dts: k3-j721e-common-proc-board: Mark main_uart0 as shared device
Main uart0 is used as debug console by both R5SPL and A72 bootloader and
Linux. So mark it as shared device so that power-domain request is
successful by both cores.
Tero Kristo [Fri, 27 Sep 2019 16:14:29 +0000 (19:14 +0300)]
board: ti: am335x-ice: Configure the CDCE913 clock synthesizer
AM335x-ICE boards contain the CDCE913 clock synthesizer, and their
reset crystal capacitance load value of 10pF is wrong leading into
lost packets in certain networking tests. Add DT data for this
device, and probe it from the board file to program the crystal
capacitance load value to 0pF to avoid any problems.
projects / u-boot.git / log