Andre Przywara [Sun, 23 Jan 2022 00:28:43 +0000 (00:28 +0000)]
sunxi: move early "SRAM setup" into separate file
Currently we do some magic "SRAM setup" MMIO writes in s_init(), copied
from the original BSP U-Boot. The comment speaks of this being required
before DRAM access gets enabled, but there is no indication that this
would actually be required that early.
Move this out of s_init(), into board_init_f(). Since this actually only
affects a very few older SoCs, the actual code goes into the cpu/armv7
directory, to move it out of the way for all other SoCs.
This also uses the opportunity to convert some #ifdefs over to the fancy
IS_ENABLED() macros used in actual C code.
We keep the s_init() stub around for now, since armv8's lowlevel_init
still relies on it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
Andre Przywara [Sun, 23 Jan 2022 00:27:19 +0000 (00:27 +0000)]
sunxi: move Cortex SMPEN setting into start.S
According to their TRMs, Cortex ARMv7 CPUs with SMP support require the
ACTLR.SMPEN bit to be set as early as possible, before any cache or TLB
maintenance operations are done. As we do those things still in start.S,
we need to move the SMPEN bit setting there, too.
This introduces a new ARMv7 wide symbol and code to set bit 6 in ACTLR
very early in start.S, and moves sunxi boards over to use that instead
of the custom code we had in our board.c file (where it was called
technically too late).
In practice we got away with this so far, because at this point all the
other cores were still in reset, so any broadcasting would have been
ignored anyway. But it is architecturally cleaner to do it early, and
we move a core specific piece of code out of board.c.
This also gets rid of the ARM_CORTEX_CPU_IS_UP kludge I introduced a few
years back, and moves the respective logic into the new Kconfig entry.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Sat, 22 Jan 2022 10:05:12 +0000 (10:05 +0000)]
sunxi: move non-essential code out of s_init()
So far all Allwinner based boards were doing some not-so-lowlevel-setup
in lowlevel's s_init() routine.
This includes the initial clock, timer and pinmux setup, among other
things. This is clearly out of the "absolute bare minimum to get started"
scope that lowlevel_init.S suggests for this function.
Since we have an SPL, which is called right after s_init(), move those
calls to our board_init_f() function. As we overwrite this only for
the SPL, this has the added benefit of not doing this setup *again*
shortly afterwards, when running U-Boot proper.
This makes gpio_init() to be called from the SPL only, so pull this code
into a CONFIG_SPL_BUILD protected part to avoid build warnings.
Reviewed-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Martin Schiller [Wed, 17 Nov 2021 11:59:20 +0000 (12:59 +0100)]
board: ls1046ardb: force PCI device enumeration
Commit 045ecf899252 ("configs: enable DM_ETH support for LS1046ARDB")
resulted in the PCI bus no longer being implicitly enumerated.
However, this is necessary for the fdt pcie fixups to work.
Therefore, similar to commit 8b6558bd4187 ("board: ls1088ardb:
transition to DM_ETH"), pci_init() is now called in the board_init()
routine when CONFIG_DM_ETH is active.
Jianpeng Bu [Mon, 31 Jan 2022 13:12:36 +0000 (18:42 +0530)]
board: ls1088a: update ifc node name to be memory-controller
IFC-NOR and QSPI are muxed on SoC.
So disable IFC node in dts if QSPI is enabled or disable QSPI node in dts
in case QSPI is not enabled.
"ifc/nor" will be changed to "memory-controller/nor" in linux. So need to
modify "ifc/nor" to "memory-controller/nor" in fdt_path_offset().
Signed-off-by: Jianpeng Bu <jianpeng.bu@nxp.com>
[Rebased] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Camelia Groza [Thu, 13 Jan 2022 13:43:14 +0000 (15:43 +0200)]
configs: fsl: add missing FMAN/QE_FW_ADDR defines
The initial patch had typos that caused four defconfigs to miss the
symbol transition to Kconfig. CONFIG_SYS_QE_FW_ADDR and
CONFIG_SYS_FMAN_FW_ADDR are currently initialized to 0 by default
on these builds, which prevents the firmware from loading.
Add the correct symbols to these defconfigs.
Fixes: a97a071d10d2b ("configs: fsl: migrate FMAN/QE specific defines to Kconfig") Signed-off-by: Camelia Groza <camelia.groza@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Vladimir Oltean [Mon, 3 Jan 2022 12:47:37 +0000 (14:47 +0200)]
arm: dts: ls1028a-qds: declare in-band autoneg for Ethernet ports
The commit in the Fixes: tag below broke traffic through switch ports
where the SERDES protocol requires in-band autoneg and this requirement
isn't described in the device tree: SGMII, QSGMII, USXGMII (with
2500Base-X, in-band autoneg isn't supported).
The LS1028A-QDS boards are not yet ready for syncing their device trees
with Linux, since Ethernet is missing there (but has been submitted):
https://lore.kernel.org/lkml/20211112223457.10599-11-leoyang.li@nxp.com/
When agreement is reached for the Ethernet support in Linux, there will
be a sync for these boards as well. For now, just enable in-band autoneg
to fix the breakage.
Fixes: e3789a726269 ("net: dsa: felix: configure the in-band autoneg property based on OF node info") Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Vladimir Oltean [Mon, 3 Jan 2022 12:47:36 +0000 (14:47 +0200)]
arm: dts: ls1028a-rdb: sync device tree with Linux
Allow device trees to be reused between Linux and U-Boot.
The source for these device trees is linux-next as of commit bd8a9cd624c6 ("arm64: dts: ls1028a-rdb: update copyright"), which was
chosen because some changes needed to be done to the Linux DTs too,
before they could be shared:
https://lore.kernel.org/linux-arm-kernel/20211202141528.2450169-5-vladimir.oltean@nxp.com/T/#m6f63c92e75fa79a01144b2c2c6dc4776e7971395
There are two more commits on the RDB device tree which haven't been
picked up yet, because they have dependencies on the SoC device tree:
dd3d936a1b17 ("arm64: dts: ls1028a: add ftm_alarm1 node to be used as wakeup source") b2e2d3e02fb6 ("arm64: dts: ls1028a-rdb: enable pwm0")
These will be picked up on the next resync.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: Michael Walle <michael@walle.cc>
Vladimir Oltean [Mon, 3 Jan 2022 12:47:35 +0000 (14:47 +0200)]
arm: dts: ls1028a-rdb: enable PCIe controllers from U-Boot dtsi
Reuse the scheme implemented by the Kontron SL28 boards in
commit d08011d7f9b4
("arm: dts: ls1028a: disable the PCIe controller by default")
and move the 'status = "okay"' lines for the PCIe controllers
inside a separate U-Boot dtsi for the LS1028A-RDB board. This way, the
existing Linux device tree can simply be dropped in.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Vladimir Oltean [Mon, 3 Jan 2022 12:47:33 +0000 (14:47 +0200)]
arm: dts: ls1028a-rdb: disable DSPI nodes
There is no SPI peripheral on the LS1028A-RDB, therefore no reason to
enable these nodes in the U-Boot device tree (and Linux does not enable
them either).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Vladimir Oltean [Mon, 3 Jan 2022 12:47:32 +0000 (14:47 +0200)]
arm: dts: ls1028a-rdb: sync Ethernet device tree nodes with Linux
In a bit of a blunder, the blamed commit in the Fixes: tag below made
the mscc_felix switch driver look at the 'managed = "in-band-status"'
device tree property, forgetting that the U-Boot device tree had not
been updated to include that property, whereas the Linux one does.
The switch is therefore described in the device tree as not requiring
in-band autoneg, but the PHY driver for VSC8514 (drivers/net/phy/mscc.c)
still enables that feature. This results in a mismatch => no traffic.
This patch is a copy-paste of the Ethernet device tree nodes from Linux,
which resolves that issue. The device tree update also renames the
Ethernet PHY labels.
Fixes: e3789a726269 ("net: dsa: felix: configure the in-band autoneg property based on OF node info") Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Vladimir Oltean [Mon, 3 Jan 2022 12:47:31 +0000 (14:47 +0200)]
arm: dts: ls1028a-rdb: sort nodes alphabetically
The nodes in the NXP LS1028A-RDB device tree are out of order, regroup
them alphabetically to have a simple delta when the Linux device tree is
brought in.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Vladimir Oltean [Mon, 3 Jan 2022 12:47:30 +0000 (14:47 +0200)]
rtc: pcf2127: remove U-Boot specific compatible string
Now that all in-tree boards have been converted to the compatible
strings from Linux, delete the support for the ad-hoc "pcf2127-rtc" one.
Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Vladimir Oltean [Mon, 3 Jan 2022 12:47:29 +0000 (14:47 +0200)]
arm: dts: lx2160a-rdb: use Linux compatible string for RTC
During the LS1028A-RDB sync with Linux device trees, it was observed
that the same RTC is present on the two boards, and the wrong compatible
string is used in both places. This change updates the RTC from the
LX2160A-RDB to use the compatible string that was established in Linux.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: Michael Walle <michael@walle.cc>
Vladimir Oltean [Mon, 3 Jan 2022 12:47:28 +0000 (14:47 +0200)]
arm: dts: ls1028a-rdb: use Linux compatible string for RTC
During this board's sync with Linux device trees, it was observed that
it doesn't use the same compatible string for the RTC node as in U-Boot.
This change makes the RTC compatible strings match, for a smoother sync.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Vladimir Oltean [Mon, 3 Jan 2022 12:47:27 +0000 (14:47 +0200)]
arm: dts: ls1028a-qds: use Linux compatible string for RTC
The LS1028A-QDS board won't be synced with the Linux device trees right
now, since those are currently still in progress (Ethernet is missing).
However, while we're at converting the RDB, it can be observed that the
same RTC is present on the two boards, and the wrong compatible string
is used in both places. This change updates the RTC from the QDS to use
the compatible string that was established in Linux.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: Michael Walle <michael@walle.cc>
Vladimir Oltean [Mon, 3 Jan 2022 12:47:26 +0000 (14:47 +0200)]
arm: dts: lx2160a-qds: use Linux compatible string for RTC
During the LS1028A-RDB sync with Linux device trees, it was observed
that the same RTC is present on the two boards, and the wrong compatible
string is used in both places. This change updates the RTC from the
LX2160A-QDS to use the compatible string that was established in Linux.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: Michael Walle <michael@walle.cc>
Vladimir Oltean [Mon, 3 Jan 2022 12:47:25 +0000 (14:47 +0200)]
arm: dts: ls1088a-rdb: use Linux compatible string for RTC
During the LS1028A-RDB sync with Linux device trees, it was observed
that the same RTC is present on the two boards, and the wrong compatible
string is used in both places. This change updates the RTC from the
LS1088A-RDB to use the compatible string that was established in Linux.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: Michael Walle <michael@walle.cc>
Vladimir Oltean [Mon, 3 Jan 2022 12:47:24 +0000 (14:47 +0200)]
arm: dts: ls1088a-qds: use Linux compatible string for RTC
During the LS1028A-RDB sync with Linux device trees, it was observed
that the same RTC is present on the two boards, and the wrong compatible
string is used in both places. This change updates the RTC from the
LS1088A-QDS to use the compatible string that was established in Linux.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: Michael Walle <michael@walle.cc>
Vladimir Oltean [Mon, 3 Jan 2022 12:47:23 +0000 (14:47 +0200)]
rtc: pcf2127: sync with Linux compatible strings
Allow this driver to be used by boards which inherit their device trees
from Linux. Compatibility is temporarily retained with the old
compatible string which is U-Boot specific, and will be removed after a
few changes.
Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Vladimir Oltean [Mon, 3 Jan 2022 12:47:22 +0000 (14:47 +0200)]
i2c: muxes: pca954x: add PCA9847 variant
This seems to be very similar to the already existing PCA9547, save for
the fact that it supports 0.8V and doesn't support 5V. In fact, it is so
similar to the PCA9547 that the NXP LS1028A-RDB board has been driving
this chip using a "nxp,pca9547" compatible string.
Create a new compatible for the PCA9847 (which is the same as in Linux)
and define the same operating parameters for it as for PCA9547.
Cc: Heiko Schocher <hs@denx.de> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Heiko Schocher <hs@denx.de> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: Michael Walle <michael@walle.cc>
Hou Zhiqiang [Tue, 7 Dec 2021 10:13:12 +0000 (18:13 +0800)]
pci: layerscape: update the searching compatible of LX2160A PCIe
The current fixup of LX2160A PCIe nodes is based on non-production
rev1 silicon, and in Linux the nodes have been updated for rev2
silicon, so update the searching compatible string to match the
kernel changes. And for compatibility with the rev1 nodes, move
forward the board specific fixup.
Martin Schiller [Tue, 23 Nov 2021 06:28:00 +0000 (07:28 +0100)]
board: ls1043ardb: force PCI device enumeration
Commit eb1986804d1d ("configs: enable DM_ETH support for LS1043ARDB")
resulted in the PCI bus no longer being implicitly enumerated.
However, this is necessary for the fdt pcie fixups to work.
Therefore, similar to commit 8b6558bd4187 ("board: ls1088ardb:
transition to DM_ETH"), pci_init() is now called in the board_init()
routine when CONFIG_DM_ETH is active.
km/ls102xa: use unused scratchrw4 address for post word
The SCRATCHRW4 is only used in secure boot scenario that is unsupported by
our design, so this address can be stolen for storing POST status.
The SCRATCHRW4 is initialized to zero at core rest.
Using a DDR address was unfortunate choice, the DDR at boot time has a
random contend and it happens that sometimes is matching POST magic number.
This behavior can lead to undefined POST behavior and u-boot ending in
failbootcmd command.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
configs/expu1/seli8: limit autoboot stop to space key
Make it in a same way as on the other FOXMC products, this also helps to
avoid unwanted stop caused by some terminal servers that are sending junk
on the serial line.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch adds default defconfig for u-boot update version, the u-boot
update defconfig is a copy of the default (factory) defconfig with:
- adapted text base and environment addresses
- explicit flag that this is a field updated u-boot version
At the time of implementation this version is only used to verify the
update procedure, in future depend on the needs this defconfig can be
extended with additional options.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
configs/expu1: enable field fail-safe u-boot update
Field fail-safe u-boot update for pg-wcom-ls102x designs is introduced
with patch: 81fb05e.
This patch enables already added support by:
- Defining default u-boot build as bootpackage (factory) image.
- Defining u-boot update image location according to the EXPU1 NOR layout.
- Extending mtd partitions according defined EXPU1 NOR layout.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch adds default defconfig for u-boot update version, the u-boot
update defconfig is a copy of the default (factory) defconfig with:
- adapted text base and environment addresses
- explicit flag that this is a field updated u-boot version
At the time of implementation this version is only used to verify the
update procedure, in future depend on the needs this defconfig can be
extended with additional options.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
configs/seli8: enable field fail-safe u-boot update
Field fail-safe u-boot update for pg-wcom-ls102x designs is introduced
with patch 81fb05e.
This patch enables already added support by:
- Defining default u-boot build as bootpackage (factory) image.
- Defining u-boot update image location according to the SELI8 NOR layout.
- Extending mtd partitions according defined SELI8 NOR layout.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
km/ls102xa: add support for field fail-safe u-boot update
Field fail-safe u-boot update procedure for pg-wcom boards is defined and
implemented by patch: 59b3403.
This patch invokes the update procedure for pg-wcom-ls102x designs during
early misc_init_f execution.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
km: common: implement field fail-safe u-boot update
This patch provides possibility for field fail-safe u-boot updates.
The implementation can be used on all pg-wcom boards that are booting from
parallel NOR flash.
When used in a board design, provided check_for_uboot_update function will
start new u-boot at defined location if updateduboot envvar is set to yes.
With this implementation it is expected that factory programmed u-boot
will always stay as it is, and optionally new u-boot can be safely
programmed by embedded software when the unit is rolled out on the field.
It is expected check_for_uboot_update to be called early in execution
before relocation (*_f) once SoC is basically initialized and environment
can be read, with this possibilities to not be able to fix a u-boot bug by
a u-boot update are reduced to minimum.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The EBOOTCNT is a reserved persistent static memory area in QRIO,
and similar to BOOTCNT is intended to be used as boot counter location.
Comparable to BOOTCNT that is reserved for u-boot main bootcount
infrastructure, EBOOTCNT is intended to be used for pg-wcom board
specific purposes (e.g implementing early boot counter for fail-safe
u-boot update).
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
km/ls102xa: dbg phy prst depends on piggy presence
The PHY for the debug interface was placed on the board for the
pg_wcom_ls102x. Hence only when a piggy is plugged, a RJ45 jack
including magnetics is connected to the MDI of the PHY. Without a
piggy the MDI lines are left floating and it does not make sense to
have an active debug PHY.
In case of expu1 an active PHY without a piggy even led to increased
jitter for syncE.
This patch only deactivates the prst line of the debug PHY when a piggy
is detected persent.
There is a request from HW designers to use this QRIO pin for detecting
DIC26_SELFTEST status instead of a GPIO pin.
This pin is typically used during production for executing POST tests and
starting test ESW bank.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
arm: ls1021a: limit debug eth phy speed to 100Mbps
Beside that mounted rgmii debug phy is 1000Mbps capable, the debug link
between the piggy board and the phy is 100Mbps only.
This leads to longer link establishment time when working in debug mode,
as phy tries to autoneg 1000Mbps.
This patch fixes the speed to 100Mbps and allows smother link establishment
time for the debug interface.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Traverse Technologies Ten64 family boards use a microcontroller
to control low level board functions like startup and reset,
as well as holding details such as the board MAC address.
Communication between the CPU and microcontroller is via
I2C.
To keep the driver structure clean between the Ten64 board
file, DM_I2C, and a future utility command, this driver
has been implemented as a misc uclass device.
Tom Rini [Mon, 31 Jan 2022 12:45:13 +0000 (07:45 -0500)]
Merge branch 'master' of https://source.denx.de/u-boot/custodians/u-boot-marvell
- kirkwood: Add Pogoplug-V4 support (Tony)
- kirkwood: GoFlex Home : Use Marvell PHY driver (Tony)
- Another set of kwboot improvements (Pali)
- Minor misc stuff
Tony Dinh [Wed, 26 Jan 2022 03:33:44 +0000 (19:33 -0800)]
arm: kirkwood: GoFlex Home : Use Marvell uclass mvgbe and PHY driver for Ethernet
The GoFlex Home board has the network chip Marvell 88E1116R.
Use uclass mvgbe and the compatible driver M88E1118R to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Add board_eth_init() to use uclass mvgbe to bring up the network.
And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Miscellaneous changes: use CONFIG_SYS_THUMB_BUILD to keep u-boot image
under 512K, use BIT macro, and cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com> Reviewed-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Tue, 25 Jan 2022 17:13:13 +0000 (18:13 +0100)]
tools: kwboot: Set debug flag to 1
This should enable BootROM output on UART.
(At least on A385 BootROM this is broken, BootROM ignores this debug
flag and does not enable its output on UART if some valid image is
available in SPI-NOR.)
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Tue, 25 Jan 2022 17:13:09 +0000 (18:13 +0100)]
tools: kwboot: Remove 2s delay before sending first xmodem packet
This delay is not needed anymore since kwboot already handles retrying
logic for incomplete xmodem packets and also forces BootROM to flush its
input queue. Removing it decreases total transfer time.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Tue, 25 Jan 2022 17:13:07 +0000 (18:13 +0100)]
tools: kwboot: Allow to use option -b without image path
Allow option -b without image path parameter, to send boot pattern and
wait for response but not send any image. This allows to use kwboot just
for processing boot pattern and user can use any other xmodem tool for
transferring the image itself (e.g. sx). Useful for debugging purposes.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Tue, 25 Jan 2022 17:13:06 +0000 (18:13 +0100)]
tools: kwboot: Show 'E' in progress output when error occurs
When kwboot is unable to resend current xmodem packet, show an 'E' in the
progress output instead of a '+'. This allows to distinguish between the
state when kwboot is retrying sending the packet and when retry is not
possible.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Tue, 25 Jan 2022 17:13:05 +0000 (18:13 +0100)]
tools: kwboot: Fix handling of repeated xmodem packets
Unfortunately during some stages of xmodem transfer, A385 BootROM is not
able to handle repeated xmodem packets. So if an error occurs during that
stage, stop the transfer and return failure.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Tue, 25 Jan 2022 17:13:04 +0000 (18:13 +0100)]
tools: kwboot: Do not change received character in kwboot_xm_recv_reply()
Marvell BootROM expects retransmission of previous xmodem packet only in
the case when it sends NAK response to the host.
Do not change non-xmodem response (possibly UART transfer error) to NAK
in kwboot_xm_recv_reply() function. Allow caller to receive original
response from device.
Change argument 'nak_on_non_xm' to 'stop_on_non_xm'. Instead of changing
non-xmodem character to NAK, stop processing on invalid character and
return it.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Tue, 25 Jan 2022 17:13:03 +0000 (18:13 +0100)]
tools: kwboot: Remove code for handling CAN byte
It is unknown why handling of CAN byte was added into kwboot tool as
Marvell BootROM does not support CAN byte. It never sends CAN byte to host
and if host sends CAN byte BootROM handles it as an unknown byte.
Remove code for handling and sending CAN bytes from the kwboot tool.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Tue, 25 Jan 2022 17:13:02 +0000 (18:13 +0100)]
tools: kwboot: Improve retrying logic for incomplete xmodem packets
Sometimes if the first byte of xmodem packet (SOH) is incorrectly
transmitted, BootROM sends NAK for every non-SOH received byte, which
makes BootROM and the host kwboot tool out of sync. BootROM automatically
re-synchronizes after 2s pause by dropping its input queue. So when
attempting retransmit for 9th time or later, ignore NAK reply from BootROM
and either wait for valid ACK or let kwboot timeout, which implies
re-synchronization.
This fixes retransmission of xmodem packets and allows kwboot to work also
without "Waiting ... and flushing tty" code which is at the beginning of
kwboot xmodem transfer.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
Tony Dinh [Tue, 25 Jan 2022 10:00:48 +0000 (02:00 -0800)]
arm: kirkwood: Pogoplug V4 : Use Marvell network PHY driver
The Pogoplug V4 board has the network chip Marvell 88E1116R. So to
properly configure the network, enable CONFIG_PHY_MARVELL to activate
the compatible driver M88E1118R.
- This patch depends on the series:
https://patchwork.ozlabs.org/project/uboot/patch/20220124061712.28316-2-mibodhi@gmail.com/
Jan Kiszka [Fri, 28 Jan 2022 19:37:53 +0000 (20:37 +0100)]
binman: Skip node generation for images read from files
We can and should run the node generator only when creating a new image.
When we read it back, there is no need to generate nodes - they already
exits, and binman does not dive that deep into the image - and there is
no way to provide the required fdt-list. So store the mode in the image
object so that Entry_fit can simply skip generator nodes when reading
them from an fdtmap.
This unbreaks all read-backs of images that contain generator nodes in
their fdtmap. To confirm this, add a corresponding test case.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
Add SPDX to dts file: Signed-off-by: Simon Glass <sjg@chromium.org>
moveconfig: Fix code relying on now-stripped newline characters
Commit 37f815cad07d ("moveconfig: Use a function to read files") adds a
helper function that can read a file as lines, but strips the newline
characters. This change broke parts of moveconfig code that relied on
their existence, resulting in a few issues:
Configs that are defined as empty aren't removed from header files (e.g.
"#define CONFIG_REMAKE_ELF"). Make regex patterns use '\b' to match word
boundaries instead of '\W' (which matched the newlines) so these lines
still match and get removed.
All changes in defconfig are considered removed by savedefconfig even
if they weren't, and line continuations in the headers aren't recognized
and removed properly, because their checks explicitly look for a newline
character. Remove the character from both comparisons.
The printed diff of header files is wrongly formatted and raises an
IndexError if a blank line was removed. Let print() print the new lines,
and use size-independent ways to check strings to fix the diff output.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
Tom Rini [Sun, 30 Jan 2022 22:12:34 +0000 (17:12 -0500)]
Merge branch 'master' of https://source.denx.de/u-boot/custodians/u-boot-sunxi
a bit delayed, the first batch of the sunxi pull request for this cycle.
This is mostly collecting some patches that were lying around for a
while, plus some recent fixes. Nothing too exciting at this point, but
of course they should be merged nevertheless.
There is the much bigger F1C100s SoC support coming up, which I hope to
be able to send in the next few days, along with the removal of sunxi's
lowlevel_init usage.
Compile tested for all 159 sunxi boards, plus briefly tested on BananaPi
M1, OrangePi Zero, Pine64 and Pine-H64.
Samuel Holland [Wed, 13 Oct 2021 00:21:27 +0000 (19:21 -0500)]
mkimage: sunxi_egon: Allow overriding the padding size
Due to a bug in the H3 SoC, where the CPU 0 hotplug flag cannot be
written, resuming CPU 0 requires using the "Super Standby" code path in
the BROM instead of the hotplug path. This path requires jumping to an
eGON image in SRAM.
This resume image, whose single purpose is to jump back to the secure
monitor, only needs to contain a single instruction. Padding the image
to 8 KiB would be wasteful of SRAM. Hook up the -B (block size) option
so users can set the block/padding size.
Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Jernej Skrabec [Sat, 29 Jan 2022 15:58:43 +0000 (16:58 +0100)]
sunxi: Fix H616 DRAM read calibration for dual rank
Although it isn't known what bit 0 in PHY reg 8 does, it's obvious that
it has to be set before read calibration and cleared afterwards. This is
already done for first rank, but not for second (copy & paste error.)
Fix it.
Fixes: f4317dbd06b6 ("sunxi: Add H616 DRAM support") Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Chris Morgan [Fri, 21 Jan 2022 13:37:32 +0000 (13:37 +0000)]
sunxi: Add option to prevent booting on power plug-in
For sunxi boards with the AXP209, AXP221, AXP809, and AXP818 PMICs
(plus possibly others, I only confirmed the datasheets for these),
it is sometimes desirable to not boot whenever the device is
plugged in. An example would be when using the NTC CHIP inside a
PocketCHIP.
This provides a configurable option to check if bit 0 of
register 0 of the PMIC says it was powered because of a power button
press (0) or a plug-in event (1). If the value is 1 and this option
is selected, the device shuts down shortly after printing a message
to console stating the reason why it's shutting down. Powering up the
board with the power button is not affected.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
[Andre: reword to speak of boot, remove #ifdefs] Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Fri, 21 Jan 2022 13:37:31 +0000 (13:37 +0000)]
pmic: axp: define ALDO_IN startup bit
Most AXP PMICs feature a "startup source" register, which keeps
information about how the PMIC started operation. Bit 0 in there means
it has been started by "plugging in the power cable".
Define a symbol in each PMIC's header file to be able to use that
register and bit later on.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Thu, 21 Oct 2021 04:52:57 +0000 (23:52 -0500)]
mmc: sunxi: Use DM_GPIO flags to set pull-up
Now that the sunxi_gpio driver handles pull-up/down via the driver
model, pin configuration does not need a platform-specific function.
Signed-off-by: Samuel Holland <samuel@sholland.org> Tested-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Thu, 21 Oct 2021 04:52:56 +0000 (23:52 -0500)]
gpio: sunxi: Implement .set_flags
This, along with gpio_flags_xlate(), allows the GPIO driver to handle
pull-up/down flags provided by consumer drivers or in the device tree.
Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Thu, 21 Oct 2021 04:52:55 +0000 (23:52 -0500)]
sunxi: gpio: Add per-bank drive and pull setters
The GPIO and pinctrl drivers need these setters for pin configuration.
Since they are DM drivers, they should not be using hardcoded base
addresses. Factor out variants of the setter functions which take a
pointer to the GPIO bank's MMIO registers.
Signed-off-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Thu, 21 Oct 2021 04:52:54 +0000 (23:52 -0500)]
sunxi: gpio: Return void from setter functions
The return values of these functions are always zero, and they are
never checked. Since they are not needed, remove them.
Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Chris Morgan [Fri, 7 Jan 2022 17:52:54 +0000 (11:52 -0600)]
i2c: mvtwsi: Add compatible string for allwinner, sun4i-a10-i2c
This adds a compatible string for the Allwinner Sun4i-A10 I2C
controller. Without this, boards based on the R8 and A13 (at a
minimum) fail to boot.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com> Acked-by: Akash Gajjar <gajjar04akash@gmail.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
sunxi: call fdt_fixup_ethernet again to set macaddr for more aliases
Sometimes some ethernet aliases do not exist in U-Boot DT but they
exist in the DT used to boot the system (for example, modified via DT
overlays). In this situation setup_environment is called again in
ft_board_setup() to generate macaddr environment variable for them.
However now the call to fdt_fixup_ethernet() is moved before the call
of ft_board_setup().
Call fdt_fixup_ethernet() again to add MAC addresses for the extra
ethernet aliases.
The driver for SPI0 on Allwinner H6 SoCs did not use the correct define
SUN50I_GPC_SPI0 for the pin function, but one for a different Allwinner
SoC series.
Fix the conditionals to use the correct define for H6 SoCs. This matches
the conditional logic in the SPL spi driver.
Tested by probing the spi-flash on a pine64_h64-model-b board with
adapted device-tree (disable mmc2, enable spi0).
Signed-off-by: Daniel Wagenknecht <dwagenk@mailbox.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tom Rini [Sat, 29 Jan 2022 18:42:58 +0000 (13:42 -0500)]
Merge branch '2022-01-28-assorted-fixes'
- Extend the pci command to support a few more features.
- Add support for custom SPL boot device names (so it's easier for users
to understand)
- Updates for am64x to address some review comments.
- Migration deadline notice for DM_SERIAL
- coreboot payload test
- Support rsa3072 signatures.
- DFU should skip writing empty UBI pages, bootcount printf format char
correction.
Ilias Apalodimas [Fri, 28 Jan 2022 22:20:32 +0000 (00:20 +0200)]
efi_loader: hash the image once before checking against db/dbx
We don't have to recalculate the image hash every time we check against a
new db/dbx entry. So let's add a flag forcing it to run once since we only
support sha256 hashes
Suggested-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Ilias Apalodimas [Fri, 28 Jan 2022 22:20:31 +0000 (00:20 +0200)]
efi_loader: correctly handle mixed hashes and signatures in db
A mix of signatures and hashes in db doesn't always work as intended.
Currently if the digest algorithm is not explicitly set to sha256 we
stop walking the security database and reject the image.
That's problematic in case we find and try to check a signature before
inspecting the sha256 hash. If the image is unsigned we will reject it
even if the digest matches.
Since we no longer reject the image on unknown algorithms add an explicit
check and reject the image if any other hash algorithm apart from sha256
is detected on dbx.
Suggested-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
projects / u-boot.git / log