Stephan Linz [Tue, 26 Jun 2012 22:28:25 +0000 (00:28 +0200)]
microblaze: Avoid compile error on systems without cfi flash
Use XILINX_FLASH_START to set/unset FLASH and RAMENV.
Error:
board.c: In function 'board_init':
board.c:134: error: 'XILINX_FLASH_START' undeclared (first use in this function)
board.c:134: error: (Each undeclared identifier is reported only once
board.c:134: error: for each function it appears in.)
Signed-off-by: Stephan Linz <linz@li-pro.net> Signed-off-by: Michal Simek <monstr@monstr.eu>
This patch dramatically drops the amount of time u-boot needs to read a
file from an ext2 partition. On a typical 2 to 5 MB file (kernels and
initrds) it goes from tens of seconds to a couple seconds.
All we are doing here is grouping contiguous blocks into one read.
Boot tested on Globalscale Technologies Dreamplug (Kirkwood ARM SoC)
with three different files. sha1sums were calculated in Linux
userspace, and then confirmed after ext2load.
Signed-off-by: Jason Cooper <u-boot@lakedaemon.net> Tested-by: Eric Nelson <eric.nelson@boundarydevices.com> Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Rob Herring [Fri, 25 May 2012 10:47:39 +0000 (10:47 +0000)]
pxe: add support for parsing local syslinux files
Add a new command "sysboot" which parses syslinux menu files and boots
using kernel and initrd specified by menu files. The operation is similar
to "pxe boot" except local files on ext2 or fat filesystem are parsed.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Rob Herring [Wed, 28 Mar 2012 05:51:36 +0000 (05:51 +0000)]
pxe: support absolute paths
If the file path starts with a '/', then don't pre-pend the bootfile path.
This fixes a problem with running 'pxe boot' multiple times where the
bootfile path gets pre-pended to itself each time.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Rob Herring [Wed, 28 Mar 2012 05:51:35 +0000 (05:51 +0000)]
pxe: support linux entries for labels
Kernels can be specified using "linux" or "kernel" entry. The difference
is kernel is supposed to detect the type of file, but for u-boot both are
treated the same.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Rob Herring [Wed, 28 Mar 2012 05:51:32 +0000 (05:51 +0000)]
menu: only timeout when menu is displayed
Make the menu timeout apply only when prompt flag is set and after the
menu is displayed. This allows auto boot to work no matter whether prompt
is set or cleared. Use the default selection if the menu times out.
This also fixes the timeout value given to readline_into_buffer to be
seconds instead of 10th of seconds.
Old behavior:
if prompt
display menu and wait for choice
else
wait for timeout
if key pressed
display menu and wait for choice
else
exit command
New behavior:
if prompt
display menu
if key pressed
wait for choice
else
boot default entry on timeout
else
boot default entry
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Tom Rini [Tue, 19 Jun 2012 22:54:35 +0000 (15:54 -0700)]
hush.c: Move default CONFIG_SYS_PROMPT_HUSH_PS2 to hush.c
Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value
different than "> " which is vision2. I have Cc'd the maintainer here
as I strongly suspect this is a bug rather than intentional behavior.
Tom Rini [Tue, 19 Jun 2012 12:54:34 +0000 (12:54 +0000)]
CONFIG_SYS_BAUDRATE_TABLE: Add <config_fallbacks.h>, place there
We provide a default table of { 9600, 19200, 38400, 57600, 115200 }
in <config_fallbacks.h> which mkconfig places after <configs/...h> in
the generated config file. This is used when a board has not set its
own table.
Vikram Narayanan [Wed, 23 May 2012 09:01:06 +0000 (09:01 +0000)]
patman: Handle creation of patman config file
patman shouts when it couldn't find a $(HOME)/.patman file.
Handle it in a sane way by creating a new one for the user.
It looks for a user.name and user.email in the global .gitconfig
file, waits for the user input if it can't find there. Update the
same in the README
Signed-off-by: Vikram Narayanan <vikram186@gmail.com> Acked-by: Simon Glass <sjg@chromium.org> Cc: Simon Glass <sjg@chromium.org> Cc: Wolfgang Denk <wd@denx.de>
Vikram Narayanan [Wed, 23 May 2012 08:58:58 +0000 (08:58 +0000)]
patman: Change the location of patman config file
Move the config file from ~/.config/patman to ~/.patman as it is
more appropriate to have it there. Update the same in the README.
Signed-off-by: Vikram Narayanan <vikram186@gmail.com> Cc: Simon Glass <sjg@chromium.org> Cc: Wolfgang Denk <wd@denx.de> Acked-by: Simon Glass <sjg@chromium.org>
Mike Frysinger [Fri, 20 Jan 2012 09:07:21 +0000 (09:07 +0000)]
cmd_mem: cmp: unify size code paths
Not only does the source code get simpler, but it also shrinks the
compiled object code too.
While we're here, tweak the summary message to avoid the plural
issue. It isn't that big of a deal, and it's currently wrong
anyways in the single (1 byte) case:
Total of 1 byte were the same
Grammar wise, that should be "was" rather than "were". The new
output people should be able to easily figure out:
Total of 1 byte(s) were the same
Total of 10 byte(s) were the same
Wolfgang Denk [Tue, 19 Jun 2012 20:14:57 +0000 (22:14 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc83xx
* 'master' of git://git.denx.de/u-boot-mpc83xx:
km/common: check test_bank and testpin for testboot
powerpc/83xx/km: readout dip_switch on kmcoge5ne
powerpc/83xx: configure CONFIG_POST for kmcoge5ne
powerpc/83xx/km: added missing enable of application buffer
km/common: increase bootlimit to 3
km/common: fixed error in ethaddr (1-byte-shift)
MAINTAINERS: cleanup for keymile boards
powerpc/83xx: add kmcoge5ne board support
km/common: add support for second flash
powerpc83xx/km: remove unneeded CONFIG_PCI for kmeter1
powerpc83xx/km: lock the window size to 2GiB befor fixing sdram size
powerpc/83xx/km: use tuxx1.h for kmsupx5 target
powerpc/83xx: increment malloc heap size for the MPC832x MDS boards
Holger Brunck [Wed, 21 Mar 2012 12:42:46 +0000 (13:42 +0100)]
powerpc/83xx: add kmcoge5ne board support
This board is a MPC8360 board. Two flashes are present
a NOR flash were u-boot and the u-boot environment is stored
and a NAND flash for the application code. This board has 512MB
SDRAM.
Additionaly we introduce a common km8360.h file and convert kmeter1 to
use this.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Christian Herzig <christian.herzig@keymile.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Heiko Schocher <hs@denx.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Andreas Huber [Fri, 4 May 2012 08:30:16 +0000 (10:30 +0200)]
km/common: add support for second flash
Add support for a second flash.
By default, a single flash chip is set up:
- called 'boot'
- mtd name for ubi 'ubi0'
MTDIDS and MTDPARTS may be overwritten to add a second flash.
The 'ubiattach' command is featured in two versions:
- if CONFIG_KM_UBI_PARTITION_NAME_APP is not defined:
this is the version as up to now
- if CONFIG_KM_UBI_PARTITION_NAME_APP is defined:
a check on 'actual_bank' will be done to determine the flash to boot
from.
Use CONFIG_KM_UBI_PARTITION_NAME_BOOT and
CONFIG_KM_UBI_PARTITION_NAME_APP to define where to put the bootloader
and the applications.
Timur Tabi [Sat, 17 Mar 2012 22:44:00 +0000 (17:44 -0500)]
powerpc/83xx: increment malloc heap size for the MPC832x MDS boards
The malloc buffer is not large enough to hold a flash sector (0x20000 bytes)
in addition to whatever else it normally holds, so double its size. This
fixes a failure trying to save the environment:
=> save
Saving Environment to Flash...
Unable to save the rest of sector (122880)
. done
Protected 1 sectors
This problem probably surfaced from some other change that significantly
increased the normal memory usage, thereby not leaving enough room for
the saveenv command.
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Wolfgang Denk [Thu, 7 Jun 2012 21:42:17 +0000 (23:42 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-video
* 'master' of git://git.denx.de/u-boot-video:
video: atmel/lcd: add LCD driver for new Atmel SoC
video: cfb_console: flush dcache for frame buffer in DRAM
cfb_console: Ignore bell character
cfb_console: Add console_clear_line function
cfb_console: Fix function console_back
omap3_dss: cosmetic changes
omap3_dss: add optional framebuffer
mx53loco: Add LCD support
mx5: Rename mx51_fb_init()
mx53: Allow IPUv3 driver to also work on mx53
mx51evk: Add LCD support
EXYNOS: display 32bpp bitmap TIZEN logo
create lib/tizen directory
LCD: display 32bpp decompressed bitmap image
common/lcd.c: reduce one CONFIG_LCD_LOGO ifdef
common/lcd.c: reduce some CONFIG_LCD_*_LOGO ifdefs
common/lcd.c: use ARRAY_SIZE
cmd_bmp.c: make bmp_display() usable by drivers or board code
LCD: support another s6e8ax0 panel type
LCD: change s6e8ax0 panel gamma value
include/video.h: drop unused video_printf()
Wolfgang Denk [Thu, 7 Jun 2012 21:34:11 +0000 (23:34 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-sh
* 'master' of git://git.denx.de/u-boot-sh:
sh/ap_sh4a_4a: Fix typo of operator in ET0_ETXD4
sh: Add SH7269 device and RSK2+SH7269 board
sh: Set CONFIG_SH_ETHER_PHY_MODE and CONFIG_SH_ETHER_SH7734_MII to boards with sh_eth
sh: Add support for AP-SH4A-4A board
sh: Add register definition of PFC for SH7734
sh: r0p7734: Add support I2C controller
sh: Add bit control functions
sh: Add support for r0p7734 board
sh: Add support Renesas SH7734
Marek Vasut [Fri, 25 May 2012 14:14:46 +0000 (16:14 +0200)]
MPC8xxx: Define cache ops for USB
This patch conditionally defines flush_dcache_range() and
invalidate_dcache_range() on MPC8xxx, to avoid EHCI complaining,
resulting in the following output:
$ ARCH=powerpc CROSS_COMPILE=powerpc-linux-gnu- ./MAKEALL MPC8572DS
Configuring for MPC8572DS board...
make: *** [u-boot] Error 1
powerpc-linux-gnu-size: './u-boot': No such file
e1000.c: In function ‘e1000_initialize’:
e1000.c:5264:13: warning: assignment from incompatible pointer type [enabled by default]
tsec.c: In function ‘tsec_initialize’:
tsec.c:638:12: warning: assignment from incompatible pointer type [enabled by default]
drivers/usb/host/libusb_host.o: In function `ehci_td_buffer':
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:186: undefined reference to `flush_dcache_range'
drivers/usb/host/libusb_host.o: In function `ehci_submit_async':
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:346: undefined reference to `flush_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:348: undefined reference to `flush_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:349: undefined reference to `flush_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:372: undefined reference to `invalidate_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:374: undefined reference to `invalidate_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:376: undefined reference to `invalidate_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:386: undefined reference to `invalidate_dcache_range'
make: *** [u-boot] Error 1
video: cfb_console: flush dcache for frame buffer in DRAM
Data cache flushing is required for frame buffer in RAM to fix the
distorted console text output. Currently this text distortion is
observed with cfb on beagleboard and N900 when running with data
cache enabled.
console_back() is called only from video_putc() which already turns
the cursor off at the beginning and turns it on at the end, so there
is no need to change the cursor in console_back().
The AP-SH4A-4A board has SH7734, 64MB DDR2-SDRAM, USB,
Ethernet, and more.
This patch supports the following functions:
- 64MB DDR2-SDRAM
- 16MB NOR Flash memory
- Serial console (SCIF)
- Ethernet (SH-Ether with Gigabit)
- I2C
Jeroen Hofstee [Fri, 18 May 2012 00:51:01 +0000 (00:51 +0000)]
omap3_dss: cosmetic changes
Remove unnecessary brackets.
Unwrap lines which are below 80 chars.
Single line comment as single line (as the rest).
Moved init values to the source code.
Jeroen Hofstee [Fri, 18 May 2012 00:51:00 +0000 (00:51 +0000)]
omap3_dss: add optional framebuffer
The beagle board uses the background color to show an orange screen during
startup. This patch adds the ability to add a frame buffer, with the
intention not to break the beagle board use case (I don't have one).
videomodes.c is not used. Scrolling depends on this patch:
Donghwa Lee [Wed, 9 May 2012 19:23:46 +0000 (19:23 +0000)]
EXYNOS: display 32bpp bitmap TIZEN logo
This patch supports drawing 32bpp bitmap TIZEN logo in exynos fb.
"tizen_hd_logo.h" data is compressed from trats_logo.bmp to
trats_logo.bmp.gz by gzip and converted to tizen_hd_logo.h header file
format by some application. The logo data is decompressed in the exynos
fb driver by bmp_display().
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Anatolij Gustschin <agust@denx.de>
Donghwa Lee [Thu, 26 Apr 2012 18:52:26 +0000 (18:52 +0000)]
LCD: support another s6e8ax0 panel type
s6e8ax0 panel has many panel of types. This patch support another panel
on TIZEN lunchbox board(HWREVISION 2). This panel has reversed panel
display type. So, I had added necessary command.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Anatolij Gustschin <agust@denx.de>
Joe Hershberger [Wed, 23 May 2012 08:01:04 +0000 (08:01 +0000)]
net: Allow filtering on debug traces in the net subsystem
Add several levels of DEBUG prints so that you can limit the noise to
the severety of your problem.
DEBUG_LL_STATE = Link local state machine changes
DEBUG_DEV_PKT = Packets or info directed to the device
DEBUG_NET_PKT = Packets on info on the network at large
DEBUG_INT_STATE = Internal network state changes
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Wed, 23 May 2012 08:00:13 +0000 (08:00 +0000)]
net: Work-around for brain-damaged Cisco equipment with arp-proxy
Cisco's arp-proxy feature fails to ignore the link-local address range
This means that a link-local device on a network with this Cisco
equipment will reply to ARP requests for our device (in addition to
our reply).
If we happen to reply first, the requester's ARP table will be
populated with our MAC address, and one packet will be sent to us...
shortly following this, the requester will get an ARP reply from the
Cisco equipment telling the requester to send packets their way
instead of to our device from now on.
This work-around detects this link-local condition and will delay
replying to the ARP request for 5ms so that the first packet is sent
to the Cisco equipment and all following packets are sent to our
device.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Wed, 23 May 2012 08:00:11 +0000 (08:00 +0000)]
net: Separate ArpRequest() into lower-level func
Link-local support will need to send ARP packets, but needs more
fine-grained control over the contents. Split the implementation
into 2 parts so link-local can share the code.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Wed, 23 May 2012 07:59:18 +0000 (07:59 +0000)]
net: Fix unused variable compile warning
If CONFIG_BOOTP_SERVERIP is not defined, unused variable warning is
reported. This was fixed upstream using a compiler feature instead
of a simple reorder of the statements.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Mike Frysinger <vapier@gentoo.org>
Joe Hershberger [Wed, 23 May 2012 07:59:16 +0000 (07:59 +0000)]
net: Add net_update_ether() to handle ARP and Ping replies
When the network is VLAN or SNAP, net_update_ether() will preserve
the original Ethernet packet header and simply replace the src and
dest MACs and the protocol
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Acked-by: Simon Glass <sjg@chromium.org>
Joe Hershberger [Wed, 23 May 2012 07:59:15 +0000 (07:59 +0000)]
net: Refactor to separate the UDP handler from the ARP handler
Call a built-in dummy if none is registered... don't require
protocols to register a handler (eliminating dummies)
NetConsole now uses the ARP handler when waiting on arp
(instead of needing a #define hack in arp.c)
Clear handlers at the end of net loop
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Acked-by: Simon Glass <sjg@chromium.org>
projects / u-boot.git / log