Sean Anderson [Fri, 16 Oct 2020 22:57:45 +0000 (18:57 -0400)]
spi: dw: Rename "cs-gpio" to "cs-gpios"
This property is named differently than other SPI drivers with the same
property, as well as the property as used in Linux.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Sean Anderson [Fri, 16 Oct 2020 22:57:44 +0000 (18:57 -0400)]
spi: dw: Convert calls to debug to dev_*
This allows different log levels to be enabled or disabled depending on the
desired level of verbosity. In particular, it allows for general debug
information to be printed while excluding more verbose logging which may
interfere with timing.
Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Sean Anderson [Fri, 16 Oct 2020 22:57:43 +0000 (18:57 -0400)]
spi: dw: Fix driving MOSI low while recieving
The resting state of MOSI is high when nothing is driving it. If we drive
it low while recieving, it looks like we are transmitting 0x00 instead of
transmitting nothing. This can confuse slaves (like SD cards) which allow
new commands to be sent over MOSI while they are returning data over MISO.
The return of MOSI from 0 to 1 at the end of recieving a byte can look like
a start bit and a transmission bit to an SD card. This will cause the card
to become out-of-sync with the SPI device, as it thinks the device has
already started transmitting two bytes of a new command. The mmc-spi driver
will not detect the R1 response from the SD card, since it is sent too
early, and offset by two bits. This patch fixes transfer errors when using
SD cards with dw spi.
Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
U-Boot is able to erase bad mtd blocks on raw nand devices, but this
is not true for spinand flashes. Lets enable this feature for spinand
flashes as well. This is extemelly useful for flash testing.
Frieder Schrempf [Mon, 22 Jun 2020 13:16:33 +0000 (16:16 +0300)]
mtd: spinand: Do not erase the block before writing a bad block marker
Currently when marking a block, we use spinand_erase_op() to erase
the block before writing the marker to the OOB area. Doing so without
waiting for the operation to finish can lead to the marking failing
silently and no bad block marker being written to the flash.
In fact we don't need to do an erase at all before writing the BBM.
The ECC is disabled for raw accesses to the OOB data and we don't
need to work around any issues with chips reporting ECC errors as it
is known to be the case for raw NAND.
Fixes: 7529df465248 ("mtd: nand: Add core infrastructure to support SPI NANDs") Cc: stable@vger.kernel.org Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200218100432.32433-4-frieder.schrempf@kontron.de
Frieder Schrempf [Mon, 22 Jun 2020 13:16:32 +0000 (16:16 +0300)]
mtd: spinand: Explicitly use MTD_OPS_RAW to write the bad block marker to OOB
When writing the bad block marker to the OOB area the access mode
should be set to MTD_OPS_RAW as it is done for reading the marker.
Currently this only works because req.mode is initialized to
MTD_OPS_PLACE_OOB (0) and spinand_write_to_cache_op() checks for
req.mode != MTD_OPS_AUTO_OOB.
Fix this by explicitly setting req.mode to MTD_OPS_RAW.
Fixes: 7529df465248 ("mtd: nand: Add core infrastructure to support SPI NANDs") Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200218100432.32433-3-frieder.schrempf@kontron.de
Frieder Schrempf [Mon, 22 Jun 2020 13:16:31 +0000 (16:16 +0300)]
mtd: spinand: Stop using spinand->oobbuf for buffering bad block markers
For reading and writing the bad block markers, spinand->oobbuf is
currently used as a buffer for the marker bytes. During the
underlying read and write operations to actually get/set the content
of the OOB area, the content of spinand->oobbuf is reused and changed
by accessing it through spinand->oobbuf and/or spinand->databuf.
This is a flaw in the original design of the SPI NAND core and at the
latest from 13c15e07eedf ("mtd: spinand: Handle the case where
PROGRAM LOAD does not reset the cache") on, it results in not having
the bad block marker written at all, as the spinand->oobbuf is
cleared to 0xff after setting the marker bytes to zero.
To fix it, we now just store the two bytes for the marker on the
stack and let the read/write operations copy it from/to the page
buffer later.
Fixes: 7529df465248 ("mtd: nand: Add core infrastructure to support SPI NANDs") Cc: stable@vger.kernel.org Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200218100432.32433-2-frieder.schrempf@kontron.de
Patrick Delaunay [Thu, 15 Oct 2020 15:18:17 +0000 (17:18 +0200)]
spi: migrate trace to dev and log macro in spi uclass
Define LOG_CATEGORY and change printf and pr_*
to dev_ (when dev is available) or log_ macro.
This patch adds the support of logging feature with log command
(filtering, display of device name in trace) and allows to
suppress traces via the syslog driver.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Fri, 23 Oct 2020 08:32:48 +0000 (14:02 +0530)]
dh_imx6: Switch to full DM-aware
Enable DM_SPI/DM_SPI_FLASH with a related config option.
Build fine, but not tested.
Cc: Ludwig Zenz <lzenz@dh-electronics.de> Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Andy Shevchenko [Thu, 3 Dec 2020 17:45:02 +0000 (19:45 +0200)]
x86: edison: Switch to DM_USB_GADGET
DM is the modern default approach for the drivers in U-Boot.
It also allows to configure code via Device Tree.
Move Intel Edison to use DM_USB_GADGET and drop hard coded values.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Andy Shevchenko [Thu, 3 Dec 2020 17:45:01 +0000 (19:45 +0200)]
x86: edison: Use dwc3-generic driver for Intel Edison
Use generic Synopsys DesignWare 3 driver on Intel Edison.
For now it's just a stub which allows future refactoring.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Andy Shevchenko [Thu, 3 Dec 2020 15:40:11 +0000 (17:40 +0200)]
x86: edison: BINMAN selection is specific to the board
The platforms based on Intel Tangier may have different requirements
how to create bootloader bundle to supply to a device. Currently
the BINMAN approach is for Intel Edison only.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Andy Shevchenko [Wed, 2 Dec 2020 10:35:32 +0000 (12:35 +0200)]
x86: edison: Add CPU to compatible string
Like in the rest of x86 boards append CPU to the board compatible string.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Andy Shevchenko [Fri, 27 Nov 2020 12:41:16 +0000 (14:41 +0200)]
x86: edison: Drop unneeded DM_PCI_COMPAT
None of the driver for Edison is using DM_PCI_COMPAT, hence drop it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Andy Shevchenko [Fri, 27 Nov 2020 12:40:48 +0000 (14:40 +0200)]
x86: tangier: Find proper memory region for relocation
It appears that U-Boot works by luck on Intel Edison board because the amount
of RAM is less than 1 GB and standard way of calculating the top of it work
for this configuration. However, this won't work if the amount of RAM is
different and split differently in address space. We have to find the suitable
window correctly.
Find proper memory region for relocation by scanning MMAP SFI table in
board_get_usable_ram_top() callback.
According to the address map documentation the Main Memory is guaranteed to lie
in the 0..2 GB range, that's why we limit search by this range.
Fixes: e71de54a4943 ("x86: Add Intel Tangier support") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fixed a typo in the commit message] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Mon, 9 Nov 2020 14:12:24 +0000 (07:12 -0700)]
x86: zimage: Update cmdline parameter to be an env var
With the updated changes to bootargs substitution[1], the zboot command
needs to be updated to get its command line from an environment variable
instead of a memory address. This is because the command-line string must
be updated to convert %U to ${uuid}, etc.
In any case it is more flexible to use a environment variable and it is
best to do this before the release to avoid a subsequent change.
Tom Rini [Tue, 15 Dec 2020 18:57:03 +0000 (13:57 -0500)]
Merge tag 'doc-2021-01-rc4' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Documentation fixes for v2020.01-rc4
Move several README files to reStructured text for the HTML documentation.
Describe register for global data on x86.
Allow building HTML documentation with Sphinx 3
Igor Opaniuk [Thu, 29 Oct 2020 10:59:19 +0000 (12:59 +0200)]
distro_bootcmd: set devtype for dhcp boot
Set $devtype for DHCP boot, which can be handy for the boot.scr
for detection of devtype used (for example, when the same boot.scr is
used for both mmc/dhcp boot):
if test ${devtype} = "dhcp"; then
...
fi
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
- Fix wrong amoswap t1 usage in startup.
- Reset the board after crash.
- Enable distro booting from an attached SCSI disk for QEMU.
- Support the optional header fields in efi header.
Marek Szyprowski [Mon, 14 Dec 2020 11:34:19 +0000 (12:34 +0100)]
usb: dwc3-meson-g12a: always configure dr-mode
dwc3_meson_g12a_force_mode() sets the dr-mode of the USB PHY. However
it skips setting the mode if it matches the one done during driver probe
(stored in private structure). This fails if the mode has been changed
to other value and then back to initial one. Fix this by configuring the
dr-mode always, regadless of the one set at the driver probe).
This fixes operation of USB gadget based drivers when they are initialized
for the second time.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Leo Yu-Chi Liang [Thu, 12 Nov 2020 02:09:52 +0000 (10:09 +0800)]
riscv: Fix efi header size for RV32
This patch depends on Atish's patch.
(https://patchwork.ozlabs.org/project/uboot/patch/20201013192331.3236458-1-atish.patra@wdc.com/)
Modify the size of the Optional Header "Windows-Specific Fields" to fit with the specification.
(https://docs.microsoft.com/en-us/windows/win32/debug/pe-format)
Atish Patra [Tue, 13 Oct 2020 19:23:31 +0000 (12:23 -0700)]
riscv: Fix efi header for RV32
RV32 should use PE32 format instead of PE32+ as the efi header format.
This requires following changes
1. A different header magic value
2. An additional parameter known as BaseOfData. Currently, it is set to
zero in absence of any usage.
Signed-off-by: Atish Patra <atish.patra@wdc.com> Reviewed-by: Bin Meng <bin.meng@windriver.com> Reviewed-by: Rick Chen <rick@andestech.com>
If an exception occurs on ARM or x86, we call panic() which will try to
reset the board. Do the same on RISC-V.
To avoid -Werror=format-zero-length move a '\n' to the string passed to
panic. We don't need a message here as depending on CONFIG_PANIC_HANG we
will either see
### ERROR ### Please RESET the board ###
or
resetting ...
as next message.
Reviewed-by: Rick Chen <rick@andestech.com> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tom Rini [Fri, 11 Dec 2020 20:55:17 +0000 (15:55 -0500)]
Merge tag 'u-boot-atmel-fixes-2021.01-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel fixes for 2021.01 cycle
This set includes very important fixes for: MMC booting on several
boards, drive strength on sam9x60ek mmc lines, compile issues for
timer.c old driver, removal of unwanted access to sam9x60 bit for
oscillator bypass mode, and eeproms read on sama5d2_icp.
Hui Song [Fri, 4 Dec 2020 15:56:19 +0000 (21:26 +0530)]
configs: lx2162aqds: Enable gpio driver in defconfig
make lx2162aqds platform to enable gpio driver.
Signed-off-by: Hui Song <hui.song_1@nxp.com> Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[Rebased] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
arm: ls102xa: select USB PHY erratum's only if USB is enabled
The USB support is not by default enabled on all designs, so it does not
make seance to have USB specific erratum's enabled on such a designs.
On our internal Hitachi-Powergrids design not using the USB controller
there is a crash when accessing those specific memory locations selected
by the erratum flags.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Chris Packham [Thu, 3 Dec 2020 03:24:29 +0000 (16:24 +1300)]
powerpc: mpc85xx: Allow boards to override CONFIG_USB_MAX_CONTROLLER_COUNT
If the board isn't strapped to enable USB1 then attempting to access it
will result in a hang. Avoid this by allowing boards to define
CONFIG_USB_MAX_CONTROLLER_COUNT.
Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Alban Bedel [Tue, 17 Nov 2020 15:20:04 +0000 (16:20 +0100)]
armv8: fsl-layerscape: Fix automatic setting of bootmcd with TF-A
When booting from TF-A there is a logic that attempt to detect if the
default environment is used, if this is the case it then set the
`bootcmd` and `mcinitcmd` depending of the device we booted from.
This detection logic is dubious as it access internals of the env
implementation and it doesn't always work correctly.
First of all it detect any valid environment as not being the
default, so after running `env default -a && saveenv` the board
doesn't boot anymore as `bootcmd` is then empty.
But it also fails in some other ways, for example it always detect a
default environment when redundant env is enabled on MMC, so in that
case `bootcmd` is overwritten on every boot.
Instead of increasing the complexity of the detection just check if
`bootcmd` and `mcinitcmd` are set in the environment and set them if
they are not.
Signed-off-by: Alban Bedel <alban.bedel@aerq.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
armv8: lx2162a: Add Soc changes to support LX2162A
LX2162 is LX2160 based SoC, it has same die as of LX2160
with different packaging.
LX2162A support 64-bit 2.9GT/s DDR4 memory, i2c, micro-click module,
microSD card, eMMC support, serial console, qspi nor flash, qsgmii,
sgmii, 25g, 40g, 50g network interface, one usb 3.0 and serdes
interface to support three PCIe gen3 interface.
Tom Rini [Wed, 9 Dec 2020 16:36:41 +0000 (11:36 -0500)]
Merge tag 'u-boot-stm32-20201209' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Manage CONFIG_ENV_EXT4_DEVICE_AND_PART in stm32mp1 board
- Update ARM STI and ARM STM STM32MP Arch maintainers emails
- Enable internal pull-ups for SDMMC1 on DHCOM SoM
The STM32MP1 DHCOM SoM can be built with either bus voltage level shifter
or without one on the SDMMC1 interface. Because the SDMMC1 interface is
limited to 50 MHz and hence SD high-speed anyway, disable the SD feedback
clock to permit operation of the same U-Boot image on both SoM with and
without voltage level shifter.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Marek Vasut [Tue, 1 Dec 2020 10:29:17 +0000 (11:29 +0100)]
ARM: dts: stm32: Enable internal pull-ups for SDMMC1 on DHCOM SoM
The default state of SD bus and clock line is logical HI. SD card IO is
open-drain and pulls the bus lines LO. Always enable the SD bus pull ups
to guarantee this behavior on DHCOM SoM. Note that on SoMs with SD bus
voltage level shifter, the pull ups are built into the level shifter,
however that has no negative impact.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Manuel Reis [Wed, 25 Nov 2020 10:16:20 +0000 (10:16 +0000)]
add check for ignored CONFIG_ENV_EXT4_DEVICE_AND_PART definition
Check whether user has explicitly defined device and partition where
environment file will be located before using 'auto' i.e. bootable
partition
Voids the need to set such partition as bootable to work with the
'dev:auto' tuple
Signed-off-by: Manuel Reis <mluis.reis@gmail.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com> Tested-by: Michael Opdenacker <michael.opdenacker@bootlin.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
- Espressobin: Simplify DT handling of board variants (Pali)
- Add Luka Perkov to maintainers of Puzzle-M801 (Luka)
- Armada 38x: Enable board specific USB2 high-speed impedance
threshold configuration (Joshua)
Claudiu Beznea [Wed, 2 Dec 2020 11:39:33 +0000 (13:39 +0200)]
clk: at91: sam9x60: remove the parsing of atmel, main-osc-bypass
Remove the parsing of atmel,main-osc-bypass DT property as the SAM9X60
have no support for crystal oscillator bypass. Setting this bit might
affect the device functionality.
Fixes: a64862284f65 ("clk: at91: sam9x60: add support compatible with CCF") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
projects / u-boot.git / log