Gabor Juhos [Tue, 12 Nov 2013 15:47:32 +0000 (16:47 +0100)]
malta: use unmapped flash base address
The physical base address of the NOR flash is 0x1e000000
on the Malta boards. The hardware also maps the first 4MiB
of the flash into the 0x1fc00000-0x1fffffff range.
Currently, U-Boot uses the mapped address to access the
flash, which does not work in recent qemu versions.
Since commit a427338b222b43197c2776cbc996936df0302f51
(mips_malta: correct reading MIPS revision at 0x1fc00010)
writing to the mapped address space causes a CPU exception.
Due to the exception, U-Boot hangs during boot when it tries
to detect the CFI flash chip.
Use the correct physical address for the MALTA_FLASH_BASE
constant to fix the problem. In order to avoid relocation
problems, also update the CONFIG_SYS_{TEXT,MONITOR}_BASE
constants.
The change makes it possible to start U-Boot on a Malta
board emulated with Qemu 1.6.1 and 1.7.0-rc0. It also
works on older versions (tested with 1.1.1, 1.2.2, 1.4.2,
1.5.3).
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Paul Burton <paul.burton@imgtec.com>
Nikita Kiryanov [Wed, 16 Oct 2013 14:23:26 +0000 (17:23 +0300)]
spi: define SPI_XFER_ONCE
The flag combination "SPI_XFER_BEGIN | SPI_XFER_END" is a common use
case of spi_xfer, and it can easily cause an already long line (spi_xfer
takes 5 parameters) to go over the 80 character limit.
define SPI_XFER_ONCE to be a shorter version of the above flag combination.
Cc: Tom Rini <trini@ti.com> Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com> Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Nikita Kiryanov [Wed, 16 Oct 2013 14:23:25 +0000 (17:23 +0300)]
spi: omap3: add support for more word lengths
Current implementation only supports 8 bit word lengths, even though
omap3 can handle anything between 4 and 32.
Update the spi interface to support changing the SPI word length,
and implement it in omap3_spi driver to support the full range of
possible word lengths.
This implementation is backwards compatible by defaulting to the old
behavior of 8 bit word lengths.
Also, it required a change to the omap3_spi non static I/O functions,
but since they are not used anywhere else, no collateral changes are required.
Cc: Tom Rini <trini@ti.com> Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com> Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Andre Heider [Sat, 9 Nov 2013 10:07:53 +0000 (11:07 +0100)]
video: bcm2835: respect the pitch value
Depending on the firmware's video options [1] the active SDTV or
HDTV mode can yield a framebuffer with noncontiguous horizontal lines,
giving a messed up display, for both, u-boot and the loaded kernel.
Fix this by setting lcd_line_length to the pitch value of the configured
framebuffer.
Remove the redundant lcd_line_length initialisation which
sneaked in when an earlier version of the patch of commit 6d330719 has been rebased.
Some lcd drivers need to setup lcd_line_length not from the
panel_info parameters but by different means. Make the
lcd_get_size() weak to allow setting lcd_line_length in
a driver specific way.
Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Stephen Warren <swarren@wwwdotorg.org>
Wolfgang Denk [Mon, 11 Nov 2013 19:12:19 +0000 (20:12 +0100)]
MPC824x: remove obsolete "PN62" board
The MPC824x processors have long reached EOL, and the PN62 board has
not seen any board-specific updates for more than a decade. It is now
causing build issues. Instead of wasting time on things nobody is
interested in any more, we rather drop this board.
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Wolfgang Grandegger <wg@grandegger.com>
cc: Tom Rini <trini@ti.com>
time.c: In function 'tick_to_time':
time.c:59:2: warning: comparison of distinct pointer types lacks a cast [enabled by default]
time.c:59:2: warning: passing argument 1 of '__div64_32' from incompatible pointer type [enabled by default]
In file included from time.c:10:0:
./u-boot-mips/include/div64.h:22:17: note: expected 'uint64_t *' but argument is of type 'long long unsigned int *'
time.c: In function 'usec_to_tick':
time.c:76:2: warning: comparison of distinct pointer types lacks a cast [enabled by default]
time.c:76:2: warning: passing argument 1 of '__div64_32' from incompatible pointer type [enabled by default]
In file included from time.c:10:0:
./u-boot-mips/include/div64.h:22:17: note: expected 'uint64_t *' but argument is of type 'long long unsigned int *'
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Paul Burton [Mon, 11 Nov 2013 11:03:26 +0000 (11:03 +0000)]
malta: arch/mips/include/asm/malta.h SPDX license tag
This patch replaces the GPL-2.0 text with a GPL-2.0
SPDX-License-Identifier tag, and adds Imagination Technologies copyright
following my recent changes.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:
include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.
include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.
Note: 'git show' will also list two files just because
they are new:
Gabor Juhos [Thu, 24 Oct 2013 12:32:00 +0000 (14:32 +0200)]
malta: define CONFIG_MEMSIZE_IN_BYTES
The memsize environment variable must contain the
memory size in bytes on the Malta board. Otherwise
Linux will use wrong memory size which causes a kernel
panic.
Define CONFIG_MEMSIZE_IN_BYTES in malta.h to avoid
that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com> Cc: Paul Burton <paul.burton@imgtec.com>
Paul Burton [Fri, 8 Nov 2013 11:18:58 +0000 (11:18 +0000)]
malta: add script & instructions to flash U-boot
This patch adds a script which may be used with MIPS Navigator Console
and a MIPS Nagivator Probe in order to flash U-boot to a MIPS Malta
development board.
Please see the newly added doc/README.malta for usage instructions.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Paul Burton [Fri, 8 Nov 2013 11:18:57 +0000 (11:18 +0000)]
malta: setup PIIX4 interrupt route
Without setting up the PIRQ[A:D] interrupt routes, PCI interrupts will
be left disabled. Linux does not set up this routing but relies upon it
having been set up by the bootloader, reading back the IRQ lines which
the PIRQ[A:D] signals have been routed to.
This patch routes PIRQA & PIRQB to IRQ 10, and PIRQC & PIRQD to IRQ 11.
This matches the setup used by YAMON.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Paul Burton [Fri, 8 Nov 2013 11:18:56 +0000 (11:18 +0000)]
malta: store environment in flash
Allow the environment to be stored in the monitor flash of a Malta
board. The environment is stored in the final 128KB of the flash, which
both leaves the majority of the flash available for U-boot code and also
matches the location which YAMON uses.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Paul Burton [Fri, 8 Nov 2013 11:18:55 +0000 (11:18 +0000)]
malta: enable RTC support
This is actually required in order for a Linux kernel to boot
successfully on a physical Malta board. Without enabling the RTC, a
Malta Linux kernel will get stuck in its estimate_frequencies function
on boot.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Paul Burton [Fri, 8 Nov 2013 11:18:54 +0000 (11:18 +0000)]
malta: disable L2 caches
Malta boards may be used with cores which support L2 caches, however
U-boot does not yet support L2 cache for MIPS. Thus for the moment we'll
disable L2 caches by setting the L2B bit in Config2. This is specific to
MTI/Imagination MIPS cores which is why this is done for the Malta board
rather than generically.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Paul Burton [Fri, 8 Nov 2013 11:18:53 +0000 (11:18 +0000)]
malta: remove cache size definitions
These will now be detected at runtime, allowing a single U-boot
configuration to function correctly with different bitstreams. Without
this you may need to re-configure, re-build and re-flash U-boot to your
Malta if you flash a new bitstream with a different cache configuration
to your old bitstream.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Paul Burton [Fri, 8 Nov 2013 11:18:50 +0000 (11:18 +0000)]
malta: support for coreFPGA6 boards
This patch adds support for running on Malta boards using coreFPGA6
core cards, including support for the msc01 system controller used
with them. The system controller is detected at runtime allowing one
U-boot binary to run on a Malta with either.
Due to the PCI I/O base differing between Maltas using gt64120 & msc01
system controllers, the UART setup is modified slightly. A second UART
is added so that there is one pointing at the correct address for each
system controller. The Malta board then defines its own
default_serial_console function to select the correct one at runtime.
The incorrect UART will simply not function.
Tested on:
- A coreFPGA6 Malta running interAptiv and proAptiv bitstreams, both
with and without an L2 cache.
- QEMU.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Paul Burton [Fri, 8 Nov 2013 11:18:49 +0000 (11:18 +0000)]
malta: setup super I/O UARTs
On a real Malta the Super I/O needs to be configured before we are able
to access the UARTs. This patch performs that configuration, setting up
the UARTs in the same way that YAMON would.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Paul Burton [Sat, 9 Nov 2013 10:22:08 +0000 (10:22 +0000)]
qemu-malta: rename to just "malta"
This is in preparation for adapting this board to function correctly on
a physical MIPS Malta board. The board is moved into an "imgtec" vendor
directory at the same time in order to ready us for any other boards
supported by Imagination in the future.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Paul Burton [Fri, 8 Nov 2013 11:18:47 +0000 (11:18 +0000)]
pci.h: allow inclusion in assembly source
This patch simply #ifdef's out the C-specific parts of pci.h when it is
included by an assembly file. This will allow the macros it contains to
be used from assembly source as will be done in a followup commit adding
support for more modern MIPS Malta boards.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Paul Burton [Fri, 8 Nov 2013 11:18:46 +0000 (11:18 +0000)]
pcnet: enable the NOUFLO feature
On relatively slow boards (such as the MIPS Malta with an FPGA core
card) it can be extremely common for transmits to underflow - to the
point where it appears they simply do not work at all. Setting the
NOUFLO bit causes the ethernet controller to not begin transmission on
the wire until a transmit start point is reached. Setting that transmit
start point to the full packet will cause the controller to only
transmit the packet once it has buffered it entirely thus preventing any
transmit underflows from occuring and allowing the controller to
function on slower boards.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Paul Burton [Fri, 8 Nov 2013 11:18:45 +0000 (11:18 +0000)]
pcnet: add cache flushing & invalidation
Ensure that the view of memory from the CPU & the ethernet controller is
coherent at the various points where they exchange data. This prevents
stale data from being transmitted or received, and prevents the driver
from getting stuck waiting for the ethernet controller to update
descriptors when in reality it has but the old values are being read
from cache.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Paul Burton [Fri, 8 Nov 2013 11:18:42 +0000 (11:18 +0000)]
mips32: detect L1 cache sizes if they're not defined
For boards such as the MIPS Malta with an FPGA core card it is desirable
to be able to detect the L1 cache sizes at runtime, since they are not
dependant upon the board but on the FPGA bitstream in use. This patch
performs that detection when the CONFIG_SYS_[DI]CACHE_SIZE macros are
not defined by the board configuration. In cases where the sizes are
detected this patch also removes the restriction that the I-cache &
D-cache line sizes must be the same, as this is not necessarily true.
If the cache sizes are defined by a configuration then they will be
hardcoded as before, so this patch will not add overhead to such
boards.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Suriyan Ramasami [Wed, 16 Oct 2013 16:54:24 +0000 (09:54 -0700)]
netconsole loses 2nd character of input
Netconsole loses the second character when used as input by
either setenv stdin nc or setenv stdin serial,nc if using CONSOLE_CONSOLE_MUX
Before a nc_send_packet() to echo the input, a check is done to see if
nc_ether is valid. If its not, it waits for an arp request and then sends
the packet (which contains the first character of line to be displayed as
output). As part of reaping the arp request, the second character is consumed.
We protect this by making the call to NetLoop(NETCONS) between
input_recursion.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Pierre Aubert [Tue, 8 Oct 2013 12:20:27 +0000 (14:20 +0200)]
env: fix the env export varname
The env export command doesn't export the first variable of the list
since commit 5a31ea04c9ee5544fbb70ad7597ea4b294840eab
"env grep" - reimplement command using hexport_r()
Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
Mark Langsdorf [Tue, 10 Sep 2013 20:20:23 +0000 (15:20 -0500)]
autoboot: add an option to override keyed autoboot
As originally implemented, setting the AUTOBOOT_KEYED config option will
prevent users from breaking into the autoboot script with ctrl-c. Restore
that option with a new config symbol.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Piotr Wilczek [Fri, 11 Oct 2013 13:43:33 +0000 (15:43 +0200)]
fs:fat: fix set file name function
Curently memcpy copies string without null terminating char because
function strlen returns only number of characters excluding
null terminating character. Replace memcpy with strcpy.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> CC: Tom Rini <trini@ti.com>
Egbert Eich [Fri, 4 Oct 2013 16:53:04 +0000 (18:53 +0200)]
cmd/gpt: Support gpt command for all devices
The gpt command was only implemented for mmc devices. There is no reason
why this command should not be generalized and be applied all other
storage device classes.
This change both simplifies the implementation and eliminates a
build failure for systems that don't support mmcs.
Signed-off-by: Egbert Eich <eich@suse.com> Tested-by: Piotr Wilczek <p.wilczek@samsung.com>
[trini: Change coding style slightly] Signed-off-by: Tom Rini <trini@ti.com>
cosmetic: doc: driver-model: Do not number driver lists
Everytime a dead driver is removed from the list,
we must re-number. This is a painful task.
Try
git show e53232250 -- doc/driver-model/UDM-serial.txt
git show 6f62f4207 -- doc/driver-model/UDM-serial.txt
git show b9f4bc34a -- doc/driver-model/UDM-serial.txt
to see what I mean.
Bo Shen [Thu, 7 Nov 2013 06:29:41 +0000 (14:29 +0800)]
usb: dfu: make nand upload working
Nowhere pass a value to len, which always 0, make no transfer which
cause uploading failed.
This patch make nand upload working. However it needs enough malloc
buffer to store read data, that means the buffer at least equal to
the upload partition size, or else it doesn't work.
Heiko Schocher [Mon, 4 Nov 2013 13:05:01 +0000 (14:05 +0100)]
usb, g_dnl: make iSerialNumber board configurable
add the possibility to set the iSerialNumber board specific.
Default value for iSerialNumber is 0x0. This value can
changed board specific through the new function
g_dnl_set_serialnumber() which must be called from the
board specific function g_dnl_bind_fixup().
Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Tested-by: Lukasz Majewski <l.majewski@samsung.com>
usb: ums: add ums exit feature by ctrl+c or by detach usb cable
This patch allows exiting from UMS mode to u-boot prompt
by detaching usb cable or by pressing ctrl+c.
Add new config: CONFIG_USB_CABLE_CHECK. If defined then board
file should provide function: usb_cable_connected() (include/usb.h)
that return 1 if cable is connected and 0 otherwise.
Changes v2:
- add a note to the README
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Marek Vasut <marex@denx.de>
usb: ums: move ums code from trats to Samsung common directory
UMS init was implemented in trats board file but mostly it comprises
common code. Due to that it has been moved to common/ums.c to avoid
code duplication in the future.
Changes:
- move ums initialization code from trats to common/ums.c
- remove unused CONFIG_USB_GADGET_MASS_STORAGE from trats.h
Changes v2:
- move this patch at the top of code cleanups patches
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Marek Vasut <marex@denx.de> Cc: Minkyu Kang <mk7.kang@samsung.com>
usb: ums: fix disk capacity miscalculation and code cleanup
This patch prevents:
- ums disk capacity miscalculation because of integer overflow
Changes v2:
- Prevents passing zero size disk capacity to ums gadget driver
- Change function ums_get_capacity() to ums_disk_init() and do ums disk
initialization before gadget init
- Remove unnecessary code from mass storage driver
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Marek Vasut <marex@denx.de>
usb: ums: code refactoring to improve reusability on other boards.
This patch introduces some cleanups to ums code. Changes:
ums common:
- introduce UMS_START_SECTOR and UMS_NUM_SECTORS as defined in
usb_mass_storage.h both default values as 0 if board config
doesn't define them
common cleanup changes:
- change name of struct "ums_board_info" to "ums"
- "ums_device" fields are moved to struct ums and "dev_num" is removed
- change function name: board_ums_init to ums_init
- remove "extern" prefixes from usb_mass_storage.h
cmd_usb_mass_storage:
- change error() to printf() if need to print info message
- change return values to command_ret_t type at ums command code
- add command usage string
Changes v2:
ums common:
- always returns number of read/write sectors
- coding style clean-up
ums gadget:
- calculate amount of read/write from device returned value.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Marek Vasut <marek.vasut@gmail.com>
Igor Grinberg [Wed, 6 Nov 2013 15:24:02 +0000 (17:24 +0200)]
README: remove wrong config name
There is no CONFIG_PCA953X_INFO symbol.
U-Boot uses CONFIG_CMD_PCA953X_INFO instead, which is described in
"Monitor Functions" section and thus no need to be repeated in the
"GPIO Support" section.
Remove the whole line.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Miao Yan [Mon, 4 Nov 2013 03:18:14 +0000 (11:18 +0800)]
common/cmd_bootm.c: fix subcommand processing in OS specific do_bootm_xxx() functions
In commit "5c427e4: use BOOTM_STATE_OS_CMDLINE flag for plain bootm"
and "3d187b3: Only pass BOOTM_STATE_OS_CMDLINE on PowerPC/MIPS",
BOOTM_STATE_OS_CMDLINE was added to do_bootm for PowerPC and MIPS. This
breaks other OSes (vxworks, netbsd, plan9,...) that don't support
subcommand processing, e.g. they all contain the following code in their
do_bootm_xxx():
if (flag & BOOTM_STATE_OS_PREP)
return 0;
if ((flag != 0) && (flag != BOOTM_STATE_OS_GO))
return 1;
which will result a "subcommand not supported" error.
This patch changes the above logic to:
/* if not go command, pretend everything to be OK */
if (flag != BOOTM_STATE_OS_GO)
return 0;
Masahiro Yamada [Fri, 1 Nov 2013 01:28:45 +0000 (10:28 +0900)]
Makefile: do not create a symbolic link to arch/${ARCH}/include/asm
In-tree build:
- Do not create a symbolic link
from include/asm to arch/${ARCH}/include/asm
- Add ${SRCTREE}/arch/arm/include into the header search path
Out-of-tree build:
- Do not create a directory ${OBJTREE}/include2
- Do not create a symbolic link
from ${OBJTREE}/include2/asm to ${SRCTREE}/arch/${ARCH}/include/asm
- Add ${SRCTREE}/arch/arm/include into the header search path
Paul Burton [Wed, 23 Oct 2013 10:17:14 +0000 (11:17 +0100)]
boards.cfg: remove trailing whitespace
Commit 93e14596 "Coding Style cleanup: replace leading SPACEs by TABs"
added trailing whitespace to a single line of boards.cfg. I presume this
was unintentional, and it causes the file to change after running it
through the reformat.py script. Remove the offending character.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Andrew Ruder [Wed, 23 Oct 2013 00:07:34 +0000 (19:07 -0500)]
cmd_nvedit.c: Add env exists command
env exists is a way to test (in hush) if an environment variable
exists. A workaround existed using printenv but this new command
doesn't require all the stdout/stderr redirection to prevent
printing information to the screen.
Masahiro Yamada [Mon, 21 Oct 2013 02:11:27 +0000 (11:11 +0900)]
MAKEALL: fix boards_by_field function
Commit 27af930e changed the boards.cfg format
and it changed boards_by_field() function incorrectly.
For tegra cpus it returned Board Name field,
not Target field.
This commit restores the behavior prior to 27af930e in the right way.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Masahiro Yamada [Mon, 21 Oct 2013 02:11:26 +0000 (11:11 +0900)]
MAKEALL: fix a bug to use CROSS_COMPILE_<ARCH>
Commit 27af930e changed the boards.cfg format but
missed to change get_target_arch() fuction.
This commit adjusts it for CROSS_COMPILE_<ARCH>
to work correctly.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Roger Meier [Mon, 4 Nov 2013 06:40:44 +0000 (07:40 +0100)]
at91: add defines for reset type
Signed-off-by: Roger Meier <r.meier@siemens.com> Acked-by: Bo Shen <voice.shen@atmel.com> Reviewed-by: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas.devel@googlemail.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
ARM: ATMEL: eb_cpux9k2: fix TEXT_BASE for ramboot target
Since more functions are enabled, the eb_cpux9k2_ram target does not boot.
This patch changed the TEXT_BASE, that the code fits between TEXT_BASE and ram end.
Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Mon, 21 Oct 2013 08:14:00 +0000 (16:14 +0800)]
arm: atmel: get rid of too many ifdeffery
Get rid of too many ifdeffery in usb ohci driver
Add following two configuration for USB clock selecting
- CONFIG_USB_ATMEL_CLK_SEL_PLLB: using PLLB as usb ohci input clock
- CONFIG_USB_ATMEL_CLK_SEL_UPLL: using UPLL as usb ohci input clock
Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Rob Herring [Fri, 18 Oct 2013 18:04:42 +0000 (13:04 -0500)]
pxe: fix handling of absolute paths
pxelinux and syslinux differ in their handling of absolute paths in menu
files. A pxelinux path is aways prepended with the bootfile path while
syslinux allows for absolute paths. u-boot was always treating a leading
/ as an absolute path breaking some pxelinux setups. Fix this by adding
a flag to distinguish pxelinux vs. syslinux behavior.
Reported-by: Ian Campbell <Ian.Campbell@citrix.com> Signed-off-by: Rob Herring <rob.herring@calxeda.com>
projects / u-boot.git / log