The ARM Juno boards can be used as somewhat decent machines to run
off-the-shelf distributions, with USB, SATA, GBit Ethernet and 8GB of
DRAM.
With stable DTs in the board's NOR flash this would work really nicely,
however the default boot command is to fetch a kernel and an initrd from
the on-board NOR flash, which sounds somewhat embedded.
Include the config_distro_bootcmd.h header and define the available
devices (starting with USB, to catch USB installer sticks) to make
distributions and UEFI work out of the box.
The NOR flash kernel functionality is still preserved as the last
resort, should all other methods fail.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Andre Przywara [Sun, 11 Jul 2021 23:07:09 +0000 (00:07 +0100)]
distro_boot: Fix block device after DHCP boot sequence
The generic distro boot sequence iterates over several types of devices,
trying one after another. In doing do, it starts with setting the
"devtype" variable, then uses this later in more generic commands.
Now most (block) device types use a local variable for that, but DHCP
puts the type into the environment, where it shadows any local variables.
As a consequence any boot attempt after bootcmd_dhcp has been run fails:
===========================
VExpress64# run bootcmd_dhcp
...
VExpress64# run bootcmd_sata0
SATA#0:
(3.0 Gbps)
SATA#1:
(No RDY)
Device 0: Model: 16GB SATA Flash Drive ....
... is now current device
Couldn't find partition dhcp 0:1
===========================
This problem typically doesn't show, because DHCP is mostly the last
command to try, but is a problem when this order is different, or when
distro_bootcmd or bootcmd_xxx are run separately or multiple times.
Let bootcmd_dhcp use a local variable, as the other kids do, to make the
order of boot commands irrelevant, and allow repeated calls.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Patrick Delaunay [Fri, 21 May 2021 07:47:31 +0000 (09:47 +0200)]
cmd: pinmux: update result of do_status
Update the result of do_status and always returns a CMD_RET_ value
(-ENOSYS was a possible result of show_pinmux).
This patch also adds pincontrol name in error messages (dev->name)
and treats correctly the status sub command when pin-controller device is
not selected.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
John Keeping [Wed, 19 May 2021 14:05:53 +0000 (15:05 +0100)]
spl: use CONFIG_IS_ENABLED(LOAD_FIT_FULL)
It's possible that LOAD_FIT_FULL will have different values for TPL and
SPL, in which case just checking CONFIG_SPL_LOAD_FIT_FULL causes this to
be compiled in to the TPL even though functions and struct members it
depends on are not.
Use CONFIG_IS_ENABLED() to ensure the correct TPL/SPL variant is
checked.
Signed-off-by: John Keeping <john@metanate.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Patrick Delaunay [Tue, 20 Jul 2021 18:09:54 +0000 (20:09 +0200)]
net: dwc_eth_qos: remove the field phyaddr of the struct eqos_priv
Since the commit commit 6a895d039ba7 ("net: Update eQos driver and FEC
driver to use eth phy interfaces") the field phyaddr of driver private data
struct eqos_priv is no more used in eqos_start() for the phy_connect()
parameter.
Now this variable is only initialized in eqos_probe_resources_stm32()
it can be removed.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Patrick Delaunay [Tue, 20 Jul 2021 18:09:52 +0000 (20:09 +0200)]
net: eth-phy: use dev_dbg and log_notice
Replace debug trace and printf to log macros:
- debug() replaced by dev_dbg() when device is available, this macro
indicate the device name since commit ceb70bb870ac ("dm: Print device
name in dev_xxx like Linux")
- printf() replaced by log_notice() to allow dispatch to log backends.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Patrick Delaunay [Tue, 20 Jul 2021 18:09:51 +0000 (20:09 +0200)]
net: eth-phy: add support of device tree configuration for gpio reset
The gpio reset and the assert or deassert delay are defined in generic
binding of the ethernet phy in Linux:
Documentation/devicetree/bindings/net/ethernet-phy.yaml
reset-gpios:
maxItems: 1
description:
The GPIO phandle and specifier for the PHY reset signal.
reset-assert-us:
description:
Delay after the reset was asserted in microseconds. If this
property is missing the delay will be skipped.
reset-deassert-us:
description:
Delay after the reset was deasserted in microseconds. If
this property is missing the delay will be skipped.
See also U-Boot: doc/device-tree-bindings/net/phy.txt
This patch adds the parsing of this common DT properties in the
u-class "eth_phy_generic", used by default in the associated driver
"eth_phy_generic_drv"
This parsing function eth_phy_of_to_plat can be reused by other
ethernet phy drivers for this uclass UCLASS_ETH_PHY.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
dm: core: fix no null pointer detection in ofnode_get_addr_size_index()
Fixed a defect of a null pointer being discovered by Coverity Scan:
CID 331544: Null pointer dereferences (REVERSE_INULL)
Null-checking "size" suggests that it may be null, but it has already been
dereferenced on all paths leading to the check.
The sandbox can handle signals. Due to a damaged global data pointer
additional exceptions in the signal handler may occur leading to an endless
loop. In this case leave the handling of the secondary exception to the
operating system.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 6 Jul 2021 16:36:41 +0000 (10:36 -0600)]
binman: Add basic support for debugging performance
One of binman's attributes is that it is extremely fast, at least for a
Python program. Add some simple timing around operations that might take
a while, such as reading an image and compressing it. This should help
to maintain the performance as new features are added.
Simon Glass [Tue, 6 Jul 2021 16:36:36 +0000 (10:36 -0600)]
binman: Put compressed data into separate files
At present compression uses the same temporary file for all invocations.
With multithreading this causes the data to become corrupted. Use a
different filename each time.
Simon Glass [Mon, 5 Jul 2021 22:33:00 +0000 (16:33 -0600)]
log: Allow padding of the function name
At present when function names are logged, the output is a little hard to
read since every function is a different length. Add a way to pad the
names so that the log messages line up vertically. This doesn't work if
the function name is very long, but it makes a big difference in most
cases.
Use 20 characters as a default since this covers the vast majority of
functions.
Simon Glass [Mon, 5 Jul 2021 22:32:59 +0000 (16:32 -0600)]
blk: Support iteration
It is useful to be able to iterate over block devices. Typically there
are fixed and removable devices. For security reasons it is sometimes
useful to ignore removable devices since they are under user control.
Add iterators which support selecting the block-device type.
Simon Glass [Mon, 5 Jul 2021 22:32:58 +0000 (16:32 -0600)]
sandbox: mmc: Support fixed MMC devices
Add support for reading devicetree flags for MMC devices. With this we
can distinguish between fixed and removable drives. Note that this
information is only available when the device is probed, not when it is
bound, since it is read in the of_to_plat() method. This could be changed
if needed later.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Simon Glass [Mon, 5 Jul 2021 22:32:57 +0000 (16:32 -0600)]
spl: Provide more information on boot failure
If SPL fails to boot, try to provide an error code to indicate what is
wrong. For example, if a uclass is missing, this can return -EPFNOSUPPORT
(-96) which provides useful information.
Add a helper for accessing the image-loader name so we can drop the use
of #ifdefs in this code.
Put this feature behind a CONFIG_SHOW_ERRORS option to avoid increasing
the code size.
Simon Glass [Mon, 5 Jul 2021 22:32:56 +0000 (16:32 -0600)]
image: Allow @ in node names when not using signatures
If signature verification is not in use we don't need to worry about
the risk of using @ in node names. Update fit_image_verify() to allow
it if the function is not enabled.
Simon Glass [Mon, 5 Jul 2021 22:32:55 +0000 (16:32 -0600)]
bloblist: Correct condition in bloblist_addrec()
It is possible to add a blob that ends at the end of the bloblist, but at
present this is not supported. Fix it and add a regression test for this
case.
Simon Glass [Mon, 5 Jul 2021 22:32:54 +0000 (16:32 -0600)]
bloblist: Tidy up a few API comments
Some comments for struct bloblist_hdr are a bit ambiguous. Update them to
clarify the meaning more precisely. Also document bloblist_get_stats()
properly.
Simon Glass [Mon, 5 Jul 2021 22:32:53 +0000 (16:32 -0600)]
bloblist: Support resizing a blob
Sometimes a blob needs to expand, e.g. because it needs to hold more log
data. Add support for this. Note that the bloblist must have sufficient
spare space for this to work.
Simon Glass [Mon, 5 Jul 2021 22:32:52 +0000 (16:32 -0600)]
cros_ec: Use standard calls for recovery-request checking
Rather than calling directly into the sandbox SDL code, we can use the
normal U-Boot console handling for this feature. Update the code, to make
it more generic.
Simon Glass [Sun, 4 Jul 2021 18:19:49 +0000 (12:19 -0600)]
dtoc: Detect drivers which do not parse correctly
At present if a driver is missing a uclass or compatible stirng, this
is silently ignored. This makes sense in most cases, particularly for
the compatible string, since it is not required except when the driver
is used with of-platdata.
But it is also not very helpful. When there is some sort of problem
with a driver, the missing compatible string (for example) may be the
cause.
Add a warning in this case, showing it only for drivers which are used
by the build.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Walter Lozano <walter.lozano@collabora.com>
Simon Glass [Sun, 4 Jul 2021 18:19:48 +0000 (12:19 -0600)]
dtoc: Detect unexpected suffix on .of_match
Some rockchip drivers use a suffix on the of_match line which is not
strictly valid. At present this causes the parsing to fail. Fix this
and offer a warning.
Simon Glass [Sun, 4 Jul 2021 18:19:45 +0000 (12:19 -0600)]
dtoc: Allow multiple warnings for a driver
At present we show when a driver is missing but this is not always that
useful. There are various reasons why a driver may appear to be missing,
such as a parse error in the source code or a missing field in the driver
declaration.
Update the implementation to record all warnings for each driver, showing
only those which relate to drivers that are actually used. This avoids
spamming the user with warnings related to a driver for a different board.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Walter Lozano <walter.lozano@collabora.com>
Vincent Chen [Thu, 8 Jul 2021 01:08:20 +0000 (09:08 +0800)]
board: sifive: unmatched: refine GEMGXL initialized function in SPL
Create a new function spl_reset_device_by_gpio to reset the device
whose reset pin is connected to the GPIO. Then, using this function
to initialize GEMGXL.
Signed-off-by: Vincent Chen <vincent.chen@sifive.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Zong Li [Tue, 20 Jul 2021 06:26:08 +0000 (14:26 +0800)]
board: sifive: drop stuff related to unmatched revision 1
This patch reverts the following commits:
- 4b4159d0f3 ("riscv: dts: add dts for unmatched rev1")
- ffe9a394df ("board: sifive: support spl multi-dtb on unmatched board")
We won't plan to support unmatched that the revision below 3 in u-boot,
so they can be dropped because they might be useless.
Changed in v2:
- rebase codebase to the latest master branch
Signed-off-by: Zong Li <zong.li@sifive.com> Suggested-by: David Abdurachmanov <david.abdurachmanov@sifive.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
riscv: booti: do not force relocation if force_reloc is not set
If force_reloc flag is not set and booti is called for an address
ouside RAM (i. e. QSPI NOR flash), we should honor that and not try
to force relocation in a bogus fashion.
Signed-off-by: Vitaly Wool <vitaly.wool@konsulko.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Zong Li [Fri, 9 Jul 2021 08:26:35 +0000 (16:26 +0800)]
board: sifive: remove the command for setting serial number
We wouldn't like to allow user to change the serial number, so remove
the command for changing serial number in EEPROM.
Signed-off-by: Zong Li <zong.li@sifive.com> Suggested-by: David Abdurachmanov <david.abdurachmanov@sifive.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Filter out dmas dma-names interrupt-parent interrupts interrupts-extended
interrupt-names interrupt-map interrupt-map-mask iommus DT properties on
R-Car Gen3, since they are not used by U-Boot and only take space.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Marek Vasut [Sat, 10 Jul 2021 16:56:29 +0000 (18:56 +0200)]
ARM: dts: rmobile: Disable RPC HF by default
The RPC HF might be locked by ATF, and any access to its register
space would result in complete hang. Disable the RPC HF by default.
The ATF should be patched to set RPC node status = "okay" in the DT
fragment it passes to U-Boot in case the RPC HF access is unlocked,
and that way U-Boot could access the RPC HF safely.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Marek Vasut [Sun, 4 Jul 2021 15:27:27 +0000 (17:27 +0200)]
ARM: rmobile: Align CPU: print with other prints
The CPU: print only has one space after it, while the other prints
from U-Boot align the value to offset 7. Align the CPU: print too.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Marek Vasut [Sat, 3 Jul 2021 18:41:50 +0000 (20:41 +0200)]
ARM: rmobile: Enable sysinfo on R-Car Gen3
Enable support for sysinfo on supported R-Car Gen3 boards. The sysinfo
is used e.g. to access and decode board-specific information and then
in turn used by board-info to print those information. On R-Car Gen3
the sysinfo rcar3 driver is used to parse the board ID EEPROM, obtain
board type and revision from it, and let board-info print this
information on boot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Marek Vasut [Sat, 3 Jul 2021 16:16:14 +0000 (18:16 +0200)]
ARM: dts: rmobile: Add sysinfo extras on R-Car Gen3
Add sysinfo node and phandle to the board ID EEPROM on all boards
where this functionality is described in DT, which is Salvator-X(S),
ULCB and Ebisu. The u-boot,dm-pre-reloc is necessary here, since the
sysinfo must be available early during boot. The V3M and V3H boards
currently do not describe this board ID EEPROM in upstream DT, but
that could be easily added later, once the DTs contain the necessary
nodes.
ULCB and Ebisu needs the full EEPROM node in the u-boot extras DT,
since the EEPROM node is still missing in the upstream DTs. Ebisu
also needs extra compatible string override for the i2c_dvfs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The Renesas R-Car Gen3 development kits contain board ID EEPROM.
This driver parses out the board ID and revision out of that
EEPROM and exports it e.g. for the board-info print on boot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Sean Anderson <sean.anderson@seco.com> Cc: Simon Glass <sjg@chromium.org>
Wasim Khan [Thu, 17 Jun 2021 07:12:59 +0000 (09:12 +0200)]
armv8: lx2160ardb: Add thermal node fixup for revc board
lx2160ardb Rev-C board has i2c node for thermal monitors
connected to different chip offset.
Add device tree fixup to use lx2160ardb dts and apply
thermal node fixups for lx2160ardb Rev-C board.
Camelia Groza [Wed, 16 Jun 2021 13:22:12 +0000 (16:22 +0300)]
arm: dts: ls1043ardb: configure the RGMII ports with rgmii-id
The RGMII ports on LS1043ARDB platforms require both RX and TX internal
delays to be enabled. The device tree reports only the TX ID because the
RX ID used to be enabled by default.
With the addition of RX ID support for the Realtek 8211F PHY driver in
commit e32e4d0f58cb ("net: phy: realtek: add rx delay support for
RTL8211F"), the RX ID is disabled by the driver if not reported explicitly.
This causes the RX to no longer work.
Change the phy-connection-type for the RGMII ports to "rgmii-id" in order
to enable both RX and TX internal delays.
- Marvell SheevaPlug: Convert Ethernet and SATA to Driver Model (Tony)
- Zyxel NSA310S NAS: Convert to Driver Model (Tony)
- Turris_omnia: Add `u-boot-env` NOR partition (Marek)
- Turris_omnia: Fixup MTD partitions in Linux' DTB (Marek)
- Espressobin: Enable 'mtd' command and define SPI NOR partitions (Pali)
Tom Rini [Mon, 19 Jul 2021 12:29:24 +0000 (08:29 -0400)]
Merge tag 'ti-v2021.10-rc1' of https://source.denx.de/u-boot/custodians/u-boot-ti
- Enabled distro boot for all TI platforms.
- Cleanup for AM335x Guardian Board
- PRUSS rproc on AM65 platform.
- Add PMIC support for J7200
- Misc fixes for Nokia RX-51
arm: mvebu: Espressobin: Enable 'mtd' command and define SPI NOR partitions
U-Boot now supports parsing SPI NOR partitions from Device Tree. So enable
'mtd' command support for Espressobin board and define partition layout in
U-Boot Espressobin DTS file. Access to SPI NOR via 'sf' command is old
method and 'mtd' command is now preferred variant.
From include file remove '#define CONFIG_MTD_PARTITIONS' as this option is
now defined and enabled in defconfig file. This change is required to fix
compile error:
CC arch/arm/lib/asm-offsets.s
In file included from include/config.h:4,
from include/common.h:16,
from lib/asm-offsets.c:14:
include/configs/mvebu_armada-37xx.h:63: warning: "CONFIG_MTD_PARTITIONS" redefined
#define CONFIG_MTD_PARTITIONS /* required for UBI partition support */
In file included from ././include/linux/kconfig.h:4,
from <command-line>:
include/generated/autoconf.h:44: note: this is the location of the previous definition
#define CONFIG_MTD_PARTITIONS 1
After enabling support for mtd command, output from 'mtd list' on
Espressobin board is:
=> mtd list
List of MTD devices:
* w25q32dw
- device: spi-flash@0
- parent: spi@10600
- driver: jedec_spi_nor
- path: /soc/internal-regs/spi@10600/spi-flash@0
- type: NOR flash
- block size: 0x1000 bytes
- min I/O: 0x1 bytes
- 0x000000000000-0x000000400000 : "w25q32dw"
- 0x000000000000-0x0000003f0000 : "firmware"
- 0x0000003f0000-0x000000400000 : "u-boot-env"
=>
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Konstantin Porotchkin <kostap@marvell.com> Reviewed-by: Stefan Roese <sr@denx.de>
projects / u-boot.git / log