From: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Date: Mon, 19 Dec 2022 01:28:21 +0000 (+0900)
Subject: mtd: spi-nor: Add support for Infineon s25fs256t
X-Git-Url: http://git.dujemihanovic.xyz/img/static/gitweb.css?a=commitdiff_plain;h=87a6d86571268be4e354fe030c53745a54f4ed8e;p=u-boot.git

mtd: spi-nor: Add support for Infineon s25fs256t

Infineon S25FS256T is 256Mbit Quad SPI NOR flash. The key features and
differences comparing to other Spansion/Cypress flash familes are:
  - 4-byte address mode by factory default
  - Quad mode is enabled by factory default
  - Supports mixture of 128KB and 64KB sectors by OTP configuration
    (this patch supports uniform 128KB only)

Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
---

diff --git a/drivers/mtd/spi/spi-nor-core.c b/drivers/mtd/spi/spi-nor-core.c
index 7d42ba9ff8..2c3116ee53 100644
--- a/drivers/mtd/spi/spi-nor-core.c
+++ b/drivers/mtd/spi/spi-nor-core.c
@@ -3195,6 +3195,10 @@ static int spi_nor_setup(struct spi_nor *nor, const struct flash_info *info,
 }
 
 #ifdef CONFIG_SPI_FLASH_SPANSION
+
+/* Use ID byte 4 to distinguish S25FS256T and S25Hx-T */
+#define S25FS256T_ID4	(0x08)
+
 static int s25_mdp_ready(struct spi_nor *nor)
 {
 	u32 addr;
@@ -3234,19 +3238,35 @@ static int s25_setup(struct spi_nor *nor, const struct flash_info *info,
 		     const struct spi_nor_flash_parameter *params)
 {
 	int ret;
-	u8 cfr3v;
+	u8 cr;
 
 #ifdef CONFIG_SPI_FLASH_BAR
 	return -ENOTSUPP; /* Bank Address Register is not supported */
 #endif
+	/*
+	 * S25FS256T has multiple sector architecture options, with selection of
+	 * count and location of 128KB and 64KB sectors. This driver supports
+	 * uniform 128KB only due to complexity of non-uniform layout.
+	 */
+	if (nor->info->id[4] == S25FS256T_ID4) {
+		ret = spansion_read_any_reg(nor, SPINOR_REG_ADDR_ARCFN, 8, &cr);
+		if (ret)
+			return ret;
+
+		if (cr) /* Option 0 (ARCFN[7:0] == 0x00) is uniform */
+			return -EOPNOTSUPP;
+
+		return spi_nor_default_setup(nor, info, params);
+	}
+
 	/*
 	 * Read CFR3V to check if uniform sector is selected. If not, assign an
 	 * erase hook that supports non-uniform erase.
 	 */
-	ret = spansion_read_any_reg(nor, SPINOR_REG_ADDR_CFR3V, 0, &cfr3v);
+	ret = spansion_read_any_reg(nor, SPINOR_REG_ADDR_CFR3V, 0, &cr);
 	if (ret)
 		return ret;
-	if (!(cfr3v & CFR3V_UNHYSA))
+	if (!(cr & CFR3V_UNHYSA))
 		nor->erase = s25_erase_non_uniform;
 
 	/*
@@ -3296,6 +3316,10 @@ static int s25_post_bfpt_fixup(struct spi_nor *nor,
 		nor->addr_mode_nbytes = 4;
 	}
 
+	/* The default address mode in S25FS256T is 4. */
+	if (nor->info->id[4] == S25FS256T_ID4)
+		nor->addr_mode_nbytes = 4;
+
 	/*
 	 * The page_size is set to 512B from BFPT, but it actually depends on
 	 * the configuration register. Look up the CFR3V and determine the
@@ -3321,12 +3345,17 @@ static int s25_post_bfpt_fixup(struct spi_nor *nor,
 static void s25_post_sfdp_fixup(struct spi_nor *nor,
 				struct spi_nor_flash_parameter *params)
 {
-	/* READ_FAST_4B (0Ch) requires mode cycles*/
-	params->reads[SNOR_CMD_READ_FAST].num_mode_clocks = 8;
-	/* PP_1_1_4 is not supported */
-	params->hwcaps.mask &= ~SNOR_HWCAPS_PP_1_1_4;
-	/* Use volatile register to enable quad */
-	params->quad_enable = s25_quad_enable;
+	if (nor->info->id[4] == S25FS256T_ID4) {
+		/* PP_1_1_4 is supported */
+		params->hwcaps.mask |= SNOR_HWCAPS_PP_1_1_4;
+	} else {
+		/* READ_FAST_4B (0Ch) requires mode cycles*/
+		params->reads[SNOR_CMD_READ_FAST].num_mode_clocks = 8;
+		/* PP_1_1_4 is not supported */
+		params->hwcaps.mask &= ~SNOR_HWCAPS_PP_1_1_4;
+		/* Use volatile register to enable quad */
+		params->quad_enable = s25_quad_enable;
+	}
 }
 
 static struct spi_nor_fixups s25_fixups = {
diff --git a/drivers/mtd/spi/spi-nor-ids.c b/drivers/mtd/spi/spi-nor-ids.c
index 5f8f3ec955..a862fbd707 100644
--- a/drivers/mtd/spi/spi-nor-ids.c
+++ b/drivers/mtd/spi/spi-nor-ids.c
@@ -294,6 +294,8 @@ const struct flash_info spi_nor_ids[] = {
 		USE_CLSR) },
 	{ INFO6("s25hs02gt",  0x342b1c, 0x0f0090, 256 * 1024, 1024,
 		SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
+	{ INFO6("s25fs256t",  0x342b19, 0x0f0890, 128 * 1024, 256,
+		SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
 #ifdef CONFIG_SPI_FLASH_S28HX_T
 	{ INFO("s28hl512t",  0x345a1a,      0, 256 * 1024, 256, SPI_NOR_OCTAL_DTR_READ) },
 	{ INFO("s28hl01gt",  0x345a1b,      0, 256 * 1024, 512, SPI_NOR_OCTAL_DTR_READ) },
diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h
index 605cddef4d..2861b73edb 100644
--- a/include/linux/mtd/spi-nor.h
+++ b/include/linux/mtd/spi-nor.h
@@ -141,6 +141,7 @@
 #define SPINOR_REG_ADDR_STR1V	0x00800000
 #define SPINOR_REG_ADDR_CFR1V	0x00800002
 #define SPINOR_REG_ADDR_CFR3V	0x00800004
+#define SPINOR_REG_ADDR_ARCFN	0x00000006
 #define CFR3V_UNHYSA		BIT(3)	/* Uniform sectors or not */
 #define CFR3V_PGMBUF		BIT(4)	/* Program buffer size */