#define CONFIG_SYS_MAXARGS 64
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+/*
+ * Increase max uncompressed/gunzip size, keeping size same as EMMC linux
+ * partition.
+ */
+#define CONFIG_SYS_BOOTM_LEN 0x01800000
+
+/* Env configuration */
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_SYS_MMC_ENV_PART 0
+
+/* Access eMMC Boot_1 and Boot_2 partitions */
+#define CONFIG_SUPPORT_EMMC_BOOT
+
+/* enable 64-bit PCI resources */
+#define CONFIG_SYS_PCI_64BIT 1
+
+#define CONSOLE_ARGS "console_args=console=ttyS0,115200n8\0"
+#define MAX_CPUS "max_cpus=maxcpus=8\0"
+#define OS_LOG_LEVEL "log_level=loglevel=7\0"
+#define EXTRA_ARGS "extra_args=earlycon=uart8250,mmio32,0x68A10000 " \
+ "earlyelog=" __stringify(ELOG_AP_UART_LOG_BASE) ",0x10000 " \
+ "crashkernel=512M reboot=w\0"
+
+#define PCIE_ARGS "pcie_args=pci=pcie_bus_safe pcie_ports=native vfio_pci.disable_idle_d3=1\0"
+
+#ifdef CONFIG_BCM_SF2_ETH
+#define ETH_ADDR "ethaddr=00:0A:F7:95:65:A4\0"
+#define NET_ARGS "bgmac_platform.ethaddr=${ethaddr} " \
+ "ip=${ipaddr}::${gatewayip}:${netmask}::${ethif}:off"
+#else
+#define ETH_ADDR
+#define NET_ARGS
+#endif
+
+#define RESERVED_MEM "reserved_mem=memmap=0xff000000$0x1000000\0"
+
+#define BASE_ARGS "${console_args} ${extra_args} ${pcie_args}" \
+ " ${max_cpus} ${log_level} ${reserved_mem}"
+#define SETBOOTARGS "setbootargs=setenv bootargs " BASE_ARGS " " NET_ARGS "\0"
+
+#define UPDATEME_FLASH_PARAMS "bcm_compat_level=4\0" \
+ "bcm_need_recovery_rootfs=0\0" \
+ "bcm_bl_flash_pending_rfs_imgs=0\0"
+
+#define KERNEL_LOADADDR_CFG \
+ "fit_image_loadaddr=0x90000000\0" \
+ "dtb_loadaddr=0x82000000\0"
+
+#define INITRD_ARGS "initrd_args=root=/dev/ram rw\0"
+#define INITRD_LOADADDR "initrd_loadaddr=0x92000000\0"
+#define INITRD_IMAGE "initrd_image=rootfs-lake-bcm958742t.cpio.gz\0"
+#define MMC_DEV "sd_device_number=0\0"
+#define EXEC_STATE "exec_state=normal\0"
+
+#define EXT4RD_ARGS "ext4rd_args="\
+ "root=/dev/mmcblk${sd_device_number}p${gpt_partition_entry} rw rootwait\0"
+
+#define WDT_CNTRL "wdt_enable=1\0" \
+ "wdt_timeout_sec=0\0"
+
+#define ELOG_SETUP \
+ "mbox0_addr=0x66424024\0"\
+ "elog_setup="\
+ "if logsetup -s ${mbox0_addr}; then "\
+ "else "\
+ "echo ELOG is not supported by this version of the MCU patch.;"\
+ "exit;"\
+ "fi;"\
+ "if logsetup -c ${mbox0_addr}; then "\
+ "echo ELOG is ready;"\
+ "else "\
+ "echo ELOG is supported, but is not set up.;"\
+ "echo Getting setup file from the server ${serverip}...;"\
+ "if tftp ${tftp_dir}elog_src.txt; then "\
+ "echo Setting up ELOG. Please wait...;"\
+ "if logsetup ${loadaddr} ${mbox0_addr} ${filesize}; "\
+ "then "\
+ "else "\
+ "echo [logsetup] ERROR.;"\
+ "fi;"\
+ "if logsetup -c ${mbox0_addr}; then "\
+ "echo ELOG is READY.;"\
+ "else "\
+ "echo ELOG is NOT SET UP.;"\
+ "fi;"\
+ "else "\
+ "echo ELOG setup file is not available on the server.;"\
+ "fi;"\
+ "fi \0"
+
+/* eMMC partition for FIT images */
+#define FIT_MMC_PARTITION \
+ "fit_partitions=" \
+ "uuid_disk=${uuid_gpt_disk};" \
+ "name=env,size=512K,uuid=${uuid_gpt_env};" \
+ "name=Image_rsa.img,size=24MiB,uuid=${uuid_gpt_linux};" \
+ "name=Image1_rsa.img,size=24MiB,uuid=${uuid_gpt_linux1};" \
+ "name=Image2_rsa.img,size=24MiB,uuid=${uuid_gpt_linux2};" \
+ "name=nitro,size=8MiB,uuid=${uuid_gpt_nitro};" \
+ "name=recovery,size=940MiB,uuid=${uuid_gpt_recovery};" \
+ "name=rootfs,size=-,uuid=${uuid_gpt_prootfs}\0"
+
+#define QSPI_FLASH_NITRO_PARAMS \
+ "spi_nitro_img_bin_start=0x400000\0" \
+ "spi_nitro_img_bin_mirror_start=0x580000\0" \
+ "spi_nitro_bspd_cfg_start=0x700000\0" \
+ "spi_nitro_bspd_mirror_cfg_start=0x710000\0" \
+
+#define QSPI_ACCESS_ENABLE \
+ "qspi_access_en=" \
+ "mw 0x68a403e8 1;" \
+ "mw 0x68a403ec 1;" \
+ "mw 0x68a403f0 1;" \
+ "mw 0x68a403f4 1;" \
+ "mw 0x68a403f8 1;" \
+ "mw 0x68a403fc 1 \0"
+
+#define FUNC_QSPI_PROBE \
+ "func_qspi_probe="\
+ "if run qspi_access_en; then "\
+ "else "\
+ "echo ${errstr} run qspi_access_en ** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if sf probe 0; then "\
+ "else "\
+ "echo echo ${errstr} sf probe command ** FAILED **;"\
+ "exit;"\
+ "fi \0"
+
+#define NITRO_FW_IMAGES \
+ "nitro_bin=nitro.img\0" \
+ "nitro_bspd_cfg=nitro_fb_bspd_config.bin\0"
+
+#define FASTBOOT_NITRO_SETUP \
+ "nitro_fastboot_type=1\0" \
+ "nitro_fastboot_secure=1\0" \
+ "nitro_fastboot_img_buffer=0\0" \
+ "nitro_fit_img_loc=0x90000000\0"
+
+#define FASTBOOT_SETUP \
+ "fastboot_nitro_setup=" \
+ "setenv errstr fastboot_setup;" \
+ "run func_qspi_probe;" \
+ /* first load header only */ \
+ "if sf read ${nitro_fit_img_loc} "\
+ "${spi_nitro_img_bin_start} 0x18; then "\
+ "else "\
+ "echo [fastboot_nitro_setup] sf read "\
+ "${spi_nitro_img_bin_start} ** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if spi_nitro_images_addr ${nitro_fit_img_loc} "\
+ "${spi_nitro_img_bin_start}; then "\
+ "else "\
+ "echo [fastboot_nitro_setup] spi_nitro_images_addr "\
+ "** FAILED **;"\
+ "exit;"\
+ "fi \0"
+
+#define CHECK_CHIMP_HS\
+ "check_chimp_hs=chimp_hs"\
+ "\0"
+
+#define FASTBOOT_NITRO "fastboot_nitro=chimp_ld_secure\0"
+
+#define FIT_IMAGE "fit_image=Image_rsa.img\0"
+#define BOOTCMD_MMC_FIT \
+ "bootcmd_mmc_fit="\
+ "mmc dev ${sd_device_number};"\
+ "if test $exec_state = normal; then " \
+ "setenv use_rootfs rootfs;"\
+ "else " \
+ "setenv use_rootfs recovery;"\
+ "fi;" \
+ "echo used filesystem :${use_rootfs};"\
+ "gpt setenv mmc ${sd_device_number} ${use_rootfs};"\
+ "setenv bootargs_fs ${setbootargs} ${ext4rd_args}; run bootargs_fs;"\
+ "gpt setenv mmc ${sd_device_number} ${fit_image};"\
+ "mmc read ${fit_image_loadaddr} ${gpt_partition_addr} "\
+ "${gpt_partition_size};"\
+ "bootm ${fit_image_loadaddr}\0"
+
+#define BOOTCMD_MMC_FITS \
+ "bootcmd_mmc_fits="\
+ "setenv mmc_fit0 " \
+ "'setenv fit_image Image_rsa.img; run bootcmd_mmc_fit';"\
+ "setenv mmc_fit1 " \
+ "'setenv fit_image Image1_rsa.img; run bootcmd_mmc_fit';"\
+ "setenv mmc_fit2 " \
+ "'setenv fit_image Image2_rsa.img; run bootcmd_mmc_fit';"\
+ "run mmc_fit0 || run mmc_fit1 || run mmc_fit2\0"
+
+#define USBDEV "usbdev=0\0"
+#define BOOTCMD_USB\
+ "bootcmd_usb="\
+ "setenv usb_image_loadaddr 90000000;"\
+ "setenv fit_image Image_rsa.img;"\
+ "setenv bootargs_fs ${setbootargs} ${initrd_args}; run bootargs_fs;"\
+ "if usb dev ${usbdev}; && usb start; then "\
+ "echo Booting from USB...;"\
+ "fatload usb ${usbdev} ${usb_image_loadaddr} ${fit_image};"\
+ "fatload usb ${usbdev} ${initrd_loadaddr} ${initrd_image};"\
+ "bootm ${usb_image_loadaddr} ${initrd_loadaddr}:${filesize};"\
+ "fi;"\
+ "\0"
+
+#define START_PCI\
+ "start_pci=pci e "\
+ "\0"
+
+#define BNXT_LOAD\
+ "bnxt_load=bnxt 0 probe "\
+ "\0"
+
+#define BOOTCMD_PXE\
+ "bootcmd_pxe="\
+ "run check_chimp_hs && "\
+ "run start_pci && "\
+ "run bnxt_load;"\
+ "setenv ethact bnxt_eth0;"\
+ "setenv autoload no;"\
+ "setenv bootargs_fs ${setbootargs} ${initrd_args}; run bootargs_fs;"\
+ "if dhcp; then "\
+ "setenv pxefile_addr_r ${loadaddr};"\
+ "if pxe get; then "\
+ "setenv ramdisk_addr_r ${initrd_loadaddr};"\
+ "setenv kernel_addr_r ${fit_image_loadaddr};"\
+ "pxe boot; "\
+ "fi;"\
+ "fi;"\
+ "\0"
+
+#define FLASH_PENDING_RFS_IMGS \
+ "flash_pending_rfs_imgs=" \
+ "if test $bcm_bl_flash_pending_rfs_imgs = 1; then " \
+ "if test $bl_flash_pending_rfs_imgs = rootfs; then " \
+ "dhcp;" \
+ "run mmc_flash_rootfs;" \
+ "fi;" \
+ "if test $bl_flash_pending_rfs_imgs = recovery; then " \
+ "dhcp;" \
+ "run mmc_flash_recovery;" \
+ "fi;" \
+ "setenv bl_flash_pending_rfs_imgs;" \
+ "fi; \0"
+
+#define CONFIG_BOOTCOMMAND "run flash_pending_rfs_imgs;" \
+ "run fastboot_nitro && "\
+ "run bootcmd_mmc_fits || "\
+ "run bootcmd_usb || "\
+ "run bootcmd_pxe"
+
+#define ARCH_ENV_SETTINGS \
+ CONSOLE_ARGS \
+ MAX_CPUS \
+ OS_LOG_LEVEL \
+ EXTRA_ARGS \
+ PCIE_ARGS \
+ ETH_ADDR \
+ RESERVED_MEM \
+ SETBOOTARGS \
+ UPDATEME_FLASH_PARAMS \
+ KERNEL_LOADADDR_CFG\
+ INITRD_ARGS \
+ INITRD_LOADADDR \
+ INITRD_IMAGE \
+ MMC_DEV \
+ EXEC_STATE \
+ EXT4RD_ARGS \
+ WDT_CNTRL \
+ ELOG_SETUP \
+ FIT_MMC_PARTITION \
+ QSPI_FLASH_NITRO_PARAMS \
+ QSPI_ACCESS_ENABLE \
+ FUNC_QSPI_PROBE \
+ NITRO_FW_IMAGES \
+ FASTBOOT_NITRO_SETUP \
+ FASTBOOT_SETUP \
+ CHECK_CHIMP_HS \
+ FASTBOOT_NITRO \
+ FIT_IMAGE \
+ BOOTCMD_MMC_FIT \
+ BOOTCMD_MMC_FITS \
+ USBDEV \
+ BOOTCMD_USB \
+ START_PCI \
+ BNXT_LOAD \
+ BOOTCMD_PXE \
+ FLASH_PENDING_RFS_IMGS
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ ARCH_ENV_SETTINGS
+
#endif /* __BCM_NS3_H */
projects / u-boot.git / commitdiff