+++ /dev/null
-/*
- * Copyright (C) 2004 Arabella Software Ltd.
- * Yuli Barcohen <yuli@arabellasw.com>
- *
- * Support for Embedded Planet EP8248 boards.
- * Tested on EP8248E.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc8260.h>
-#include <ioports.h>
-
-/*
- * I/O Port configuration table
- *
- * if conf is 1, then that port pin will be configured at boot time
- * according to the five values podr/pdir/ppar/psor/pdat for that entry
- */
-
-#define CONFIG_SYS_FCC1 (CONFIG_ETHER_ON_FCC1 == 1)
-#define CONFIG_SYS_FCC2 (CONFIG_ETHER_ON_FCC2 == 1)
-
-const iop_conf_t iop_conf_tab[4][32] = {
-
- /* Port A */
- { /* conf ppar psor pdir podr pdat */
- /* PA31 */ { CONFIG_SYS_FCC1, 1, 1, 0, 0, 0 }, /* FCC1 MII COL */
- /* PA30 */ { CONFIG_SYS_FCC1, 1, 1, 0, 0, 0 }, /* FCC1 MII CRS */
- /* PA29 */ { CONFIG_SYS_FCC1, 1, 1, 1, 0, 0 }, /* FCC1 MII TX_ER */
- /* PA28 */ { CONFIG_SYS_FCC1, 1, 1, 1, 0, 0 }, /* FCC1 MII TX_EN */
- /* PA27 */ { CONFIG_SYS_FCC1, 1, 1, 0, 0, 0 }, /* FCC1 MII RX_DV */
- /* PA26 */ { CONFIG_SYS_FCC1, 1, 1, 0, 0, 0 }, /* FCC1 MII RX_ER */
- /* PA25 */ { 0, 0, 0, 0, 0, 0 }, /* PA25 */
- /* PA24 */ { 0, 0, 0, 0, 0, 0 }, /* PA24 */
- /* PA23 */ { 0, 0, 0, 0, 0, 0 }, /* PA23 */
- /* PA22 */ { 0, 0, 0, 0, 0, 0 }, /* PA22 */
- /* PA21 */ { CONFIG_SYS_FCC1, 1, 0, 1, 0, 0 }, /* FCC1 MII TxD[3] */
- /* PA20 */ { CONFIG_SYS_FCC1, 1, 0, 1, 0, 0 }, /* FCC1 MII TxD[2] */
- /* PA19 */ { CONFIG_SYS_FCC1, 1, 0, 1, 0, 0 }, /* FCC1 MII TxD[1] */
- /* PA18 */ { CONFIG_SYS_FCC1, 1, 0, 1, 0, 0 }, /* FCC1 MII TxD[0] */
- /* PA17 */ { CONFIG_SYS_FCC1, 1, 0, 0, 0, 0 }, /* FCC1 MII RxD[0] */
- /* PA16 */ { CONFIG_SYS_FCC1, 1, 0, 0, 0, 0 }, /* FCC1 MII RxD[1] */
- /* PA15 */ { CONFIG_SYS_FCC1, 1, 0, 0, 0, 0 }, /* FCC1 MII RxD[2] */
- /* PA14 */ { CONFIG_SYS_FCC1, 1, 0, 0, 0, 0 }, /* FCC1 MII RxD[3] */
- /* PA13 */ { 0, 0, 0, 0, 0, 0 }, /* PA13 */
- /* PA12 */ { 0, 0, 0, 0, 0, 0 }, /* PA12 */
- /* PA11 */ { 0, 0, 0, 0, 0, 0 }, /* PA11 */
- /* PA10 */ { 0, 0, 0, 0, 0, 0 }, /* PA10 */
- /* PA9 */ { 0, 1, 0, 1, 0, 0 }, /* SMC2 TxD */
- /* PA8 */ { 0, 1, 0, 0, 0, 0 }, /* SMC2 RxD */
- /* PA7 */ { 0, 0, 0, 0, 0, 0 }, /* PA7 */
- /* PA6 */ { 0, 0, 0, 0, 0, 0 }, /* PA6 */
- /* PA5 */ { 0, 0, 0, 0, 0, 0 }, /* PA5 */
- /* PA4 */ { 0, 0, 0, 0, 0, 0 }, /* PA4 */
- /* PA3 */ { 0, 0, 0, 0, 0, 0 }, /* PA3 */
- /* PA2 */ { 0, 0, 0, 0, 0, 0 }, /* PA2 */
- /* PA1 */ { 0, 0, 0, 0, 0, 0 }, /* PA1 */
- /* PA0 */ { 0, 0, 0, 0, 0, 0 } /* PA0 */
- },
-
- /* Port B */
- { /* conf ppar psor pdir podr pdat */
- /* PB31 */ { CONFIG_SYS_FCC2, 1, 0, 1, 0, 0 }, /* FCC2 MII TX_ER */
- /* PB30 */ { CONFIG_SYS_FCC2, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_DV */
- /* PB29 */ { CONFIG_SYS_FCC2, 1, 1, 1, 0, 0 }, /* FCC2 MII TX_EN */
- /* PB28 */ { CONFIG_SYS_FCC2, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_ER */
- /* PB27 */ { CONFIG_SYS_FCC2, 1, 0, 0, 0, 0 }, /* FCC2 MII COL */
- /* PB26 */ { CONFIG_SYS_FCC2, 1, 0, 0, 0, 0 }, /* FCC2 MII CRS */
- /* PB25 */ { CONFIG_SYS_FCC2, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[3] */
- /* PB24 */ { CONFIG_SYS_FCC2, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[2] */
- /* PB23 */ { CONFIG_SYS_FCC2, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[1] */
- /* PB22 */ { CONFIG_SYS_FCC2, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[0] */
- /* PB21 */ { CONFIG_SYS_FCC2, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[0] */
- /* PB20 */ { CONFIG_SYS_FCC2, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[1] */
- /* PB19 */ { CONFIG_SYS_FCC2, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[2] */
- /* PB18 */ { CONFIG_SYS_FCC2, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[3] */
- /* PB17 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB16 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB15 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB14 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB13 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB12 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB11 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB10 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB9 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB8 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB7 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB6 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB5 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB4 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB3 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB2 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB1 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PB0 */ { 0, 0, 0, 0, 0, 0 } /* non-existent */
- },
-
- /* Port C */
- { /* conf ppar psor pdir podr pdat */
- /* PC31 */ { 0, 0, 0, 0, 0, 0 }, /* PC31 */
- /* PC30 */ { 0, 0, 0, 0, 0, 0 }, /* PC30 */
- /* PC29 */ { 0, 0, 0, 0, 0, 0 }, /* PC29 */
- /* PC28 */ { 0, 0, 0, 0, 0, 0 }, /* PC28 */
- /* PC27 */ { 0, 0, 0, 0, 0, 0 }, /* PC27 */
- /* PC26 */ { 0, 0, 0, 0, 0, 0 }, /* PC26 */
- /* PC25 */ { 0, 0, 0, 0, 0, 0 }, /* PC25 */
- /* PC24 */ { 0, 0, 0, 0, 0, 0 }, /* PC24 */
- /* PC23 */ { 0, 0, 0, 0, 0, 0 }, /* PC23 */
- /* PC22 */ { CONFIG_SYS_FCC1, 1, 0, 0, 0, 0 }, /* FCC1 RxClk (CLK10) */
- /* PC21 */ { CONFIG_SYS_FCC1, 1, 0, 0, 0, 0 }, /* FCC1 TxClk (CLK11) */
- /* PC20 */ { 0, 0, 0, 0, 0, 0 }, /* PC20 */
- /* PC19 */ { CONFIG_SYS_FCC2, 1, 0, 0, 0, 0 }, /* FCC2 RxClk (CLK13) */
- /* PC18 */ { CONFIG_SYS_FCC2, 1, 0, 0, 0, 0 }, /* FCC2 TxClk (CLK14) */
- /* PC17 */ { 0, 0, 0, 0, 0, 0 }, /* PC17 */
- /* PC16 */ { 0, 0, 0, 0, 0, 0 }, /* PC16 */
- /* PC15 */ { 0, 0, 0, 0, 0, 0 }, /* PC15 */
- /* PC14 */ { 0, 0, 0, 0, 0, 0 }, /* PC14 */
- /* PC13 */ { 0, 0, 0, 0, 0, 0 }, /* PC13 */
- /* PC12 */ { 0, 0, 0, 0, 0, 0 }, /* PC12 */
- /* PC11 */ { 0, 0, 0, 0, 0, 0 }, /* PC11 */
- /* PC10 */ { 0, 0, 0, 0, 0, 0 }, /* PC10 */
- /* PC9 */ { 1, 0, 0, 1, 0, 1 }, /* MDIO */
- /* PC8 */ { 1, 0, 0, 1, 0, 1 }, /* MDC */
- /* PC7 */ { 0, 0, 0, 0, 0, 0 }, /* PC7 */
- /* PC6 */ { 0, 0, 0, 0, 0, 0 }, /* PC6 */
- /* PC5 */ { 1, 1, 0, 1, 0, 0 }, /* SMC1 TxD */
- /* PC4 */ { 1, 1, 0, 0, 0, 0 }, /* SMC1 RxD */
- /* PC3 */ { 0, 0, 0, 0, 0, 0 }, /* PC3 */
- /* PC2 */ { 0, 0, 0, 0, 0, 0 }, /* PC2 */
- /* PC1 */ { 0, 0, 0, 0, 0, 0 }, /* PC1 */
- /* PC0 */ { 0, 0, 0, 0, 0, 0 }, /* PC0 */
- },
-
- /* Port D */
- { /* conf ppar psor pdir podr pdat */
- /* PD31 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 RxD */
- /* PD30 */ { 1, 1, 1, 1, 0, 0 }, /* SCC1 TxD */
- /* PD29 */ { 0, 0, 0, 0, 0, 0 }, /* PD29 */
- /* PD28 */ { 0, 0, 0, 0, 0, 0 }, /* PD28 */
- /* PD27 */ { 0, 0, 0, 0, 0, 0 }, /* PD27 */
- /* PD26 */ { 0, 0, 0, 0, 0, 0 }, /* PD26 */
- /* PD25 */ { 0, 0, 0, 0, 0, 0 }, /* PD25 */
- /* PD24 */ { 0, 0, 0, 0, 0, 0 }, /* PD24 */
- /* PD23 */ { 0, 0, 0, 0, 0, 0 }, /* PD23 */
- /* PD22 */ { 0, 0, 0, 0, 0, 0 }, /* PD22 */
- /* PD21 */ { 0, 0, 0, 0, 0, 0 }, /* PD21 */
- /* PD20 */ { 0, 0, 0, 0, 0, 0 }, /* PD20 */
- /* PD19 */ { 0, 0, 0, 0, 0, 0 }, /* PD19 */
- /* PD18 */ { 0, 0, 0, 0, 0, 0 }, /* PD18 */
- /* PD17 */ { 0, 0, 0, 0, 0, 0 }, /* PD17 */
- /* PD16 */ { 0, 0, 0, 0, 0, 0 }, /* PD16 */
- /* PD15 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SDA */
- /* PD14 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SCL */
- /* PD13 */ { 0, 0, 0, 0, 0, 0 }, /* PD13 */
- /* PD12 */ { 0, 0, 0, 0, 0, 0 }, /* PD12 */
- /* PD11 */ { 0, 0, 0, 0, 0, 0 }, /* PD11 */
- /* PD10 */ { 0, 0, 0, 0, 0, 0 }, /* PD10 */
- /* PD9 */ { 0, 0, 0, 0, 0, 0 }, /* PD9 */
- /* PD8 */ { 0, 0, 0, 0, 0, 0 }, /* PD8 */
- /* PD7 */ { 0, 0, 0, 0, 0, 0 }, /* PD7 */
- /* PD6 */ { 0, 0, 0, 0, 0, 0 }, /* PD6 */
- /* PD5 */ { 0, 0, 0, 0, 0, 0 }, /* PD5 */
- /* PD4 */ { 0, 0, 0, 0, 0, 0 }, /* PD4 */
- /* PD3 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PD2 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PD1 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */
- /* PD0 */ { 0, 0, 0, 0, 0, 0 } /* non-existent */
- }
-};
-
-int board_early_init_f (void)
-{
- vu_char *bcsr = (vu_char *)CONFIG_SYS_BCSR;
-
- bcsr[4] |= 0x30; /* Turn the LEDs off */
-
-#if defined(CONFIG_CONS_ON_SMC) || defined(CONFIG_KGDB_ON_SMC)
- bcsr[6] |= 0x10;
-#endif
-#if defined(CONFIG_CONS_ON_SCC) || defined(CONFIG_KGDB_ON_SCC)
- bcsr[7] |= 0x10;
-#endif
-
-#if CONFIG_SYS_FCC1
- bcsr[8] |= 0xC0;
-#endif /* CONFIG_SYS_FCC1 */
-#if CONFIG_SYS_FCC2
- bcsr[8] |= 0x30;
-#endif /* CONFIG_SYS_FCC2 */
-
- return 0;
-}
-
-phys_size_t initdram(int board_type)
-{
- vu_char *bcsr = (vu_char *)CONFIG_SYS_BCSR;
- long int msize = 16L << (bcsr[2] & 3);
-
-#ifndef CONFIG_SYS_RAMBOOT
- volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- volatile memctl8260_t *memctl = &immap->im_memctl;
- vu_char *ramaddr = (vu_char *)CONFIG_SYS_SDRAM_BASE;
- uchar c = 0xFF;
- uint psdmr = CONFIG_SYS_PSDMR;
- int i;
-
- immap->im_siu_conf.sc_ppc_acr = 0x02;
- immap->im_siu_conf.sc_ppc_alrh = 0x30126745;
- immap->im_siu_conf.sc_tescr1 = 0x00004000;
-
- memctl->memc_mptpr = CONFIG_SYS_MPTPR;
-
- /* Initialise 60x bus SDRAM */
- memctl->memc_psrt = CONFIG_SYS_PSRT;
- memctl->memc_or1 = CONFIG_SYS_SDRAM_OR;
- memctl->memc_br1 = CONFIG_SYS_SDRAM_BR;
- memctl->memc_psdmr = psdmr | PSDMR_OP_PREA; /* Precharge all banks */
- *ramaddr = c;
- memctl->memc_psdmr = psdmr | PSDMR_OP_CBRR; /* CBR refresh */
- for (i = 0; i < 8; i++)
- *ramaddr = c;
- memctl->memc_psdmr = psdmr | PSDMR_OP_MRW; /* Mode Register write */
- *ramaddr = c;
- memctl->memc_psdmr = psdmr | PSDMR_RFEN; /* Refresh enable */
- *ramaddr = c;
-#endif /* !CONFIG_SYS_RAMBOOT */
-
- /* Return total 60x bus SDRAM size */
- return msize * 1024 * 1024;
-}
-
-int checkboard(void)
-{
- vu_char *bcsr = (vu_char *)CONFIG_SYS_BCSR;
-
- puts("Board: ");
- switch (bcsr[0]) {
- case 0x0C:
- printf("EP8248E 1.0 CPLD revision %d\n", bcsr[1]);
- break;
- default:
- printf("unknown: ID=%02X\n", bcsr[0]);
- }
-
- return 0;
-}
-
-#if defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT)
-void ft_board_setup(void *blob, bd_t *bd)
-{
- ft_cpu_setup( blob, bd);
-}
-#endif /* defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT) */
+++ /dev/null
-/*
- * Copyright (C) 2004 Arabella Software Ltd.
- * Yuli Barcohen <yuli@arabellasw.com>
- *
- * U-Boot configuration for Embedded Planet EP8248 boards.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_MPC8248
-#define CPU_ID_STR "MPC8248"
-
-#define CONFIG_EP8248 /* Embedded Planet EP8248 board */
-
-#define CONFIG_SYS_TEXT_BASE 0xFFF00000
-
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
-
-/* Allow serial number (serial#) and MAC address (ethaddr) to be overwritten */
-#define CONFIG_ENV_OVERWRITE
-
-/*
- * Select serial console configuration
- *
- * If either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
- * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
- * for SCC).
- */
-#define CONFIG_CONS_ON_SMC /* Console is on SMC */
-#undef CONFIG_CONS_ON_SCC /* It's not on SCC */
-#undef CONFIG_CONS_NONE /* It's not on external UART */
-#define CONFIG_CONS_INDEX 1 /* SMC1 is used for console */
-
-#define CONFIG_SYS_BCSR 0xFA000000
-
-/* Pass open firmware flat device tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
-#define OF_TBCLK (bd->bi_busfreq / 4)
-#define OF_STDOUT_PATH "/soc/cpm/serial <at> 11a80"
-
-/* Select ethernet configuration */
-#undef CONFIG_ETHER_ON_SCC /* Ethernet is not on SCC */
-#define CONFIG_ETHER_ON_FCC /* Ethernet is on FCC */
-#undef CONFIG_ETHER_NONE /* No external Ethernet */
-
-#define CONFIG_SYS_CPMFCR_RAMTYPE 0
-#define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB)
-
-#define CONFIG_HAS_ETH0
-#define CONFIG_ETHER_ON_FCC1 1
-/* - Rx clock is CLK10
- * - Tx clock is CLK11
- * - BDs/buffers on 60x bus
- * - Full duplex
- */
-#define CONFIG_SYS_CMXFCR_MASK1 (CMXFCR_FC1 | CMXFCR_RF1CS_MSK | CMXFCR_TF1CS_MSK)
-#define CONFIG_SYS_CMXFCR_VALUE1 (CMXFCR_RF1CS_CLK10 | CMXFCR_TF1CS_CLK11)
-
-#define CONFIG_HAS_ETH1
-#define CONFIG_ETHER_ON_FCC2 1
-/* - Rx clock is CLK13
- * - Tx clock is CLK14
- * - BDs/buffers on 60x bus
- * - Full duplex
- */
-#define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
-#define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
-
-#define CONFIG_MII /* MII PHY management */
-#define CONFIG_BITBANGMII /* Bit-banged MDIO interface */
-/*
- * GPIO pins used for bit-banged MII communications
- */
-#define MDIO_PORT 0 /* Not used - implemented in BCSR */
-
-#define MDIO_ACTIVE (*(vu_char *)(CONFIG_SYS_BCSR + 8) &= 0xFB)
-#define MDIO_TRISTATE (*(vu_char *)(CONFIG_SYS_BCSR + 8) |= 0x04)
-#define MDIO_READ (*(vu_char *)(CONFIG_SYS_BCSR + 8) & 1)
-
-#define MDIO(bit) if(bit) *(vu_char *)(CONFIG_SYS_BCSR + 8) |= 0x01; \
- else *(vu_char *)(CONFIG_SYS_BCSR + 8) &= 0xFE
-
-#define MDC(bit) if(bit) *(vu_char *)(CONFIG_SYS_BCSR + 8) |= 0x02; \
- else *(vu_char *)(CONFIG_SYS_BCSR + 8) &= 0xFD
-
-#define MIIDELAY udelay(1)
-
-#ifndef CONFIG_8260_CLKIN
-#define CONFIG_8260_CLKIN 66000000 /* in Hz */
-#endif
-
-#define CONFIG_BAUDRATE 38400
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ECHO
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IMMAP
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-
-
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#define CONFIG_BOOTCOMMAND "bootm FF860000" /* autoboot command */
-#define CONFIG_BOOTARGS "root=/dev/mtdblock1 rw mtdparts=phys:7M(root),-(root)ro"
-
-#if defined(CONFIG_CMD_KGDB)
-#undef CONFIG_KGDB_ON_SMC /* define if kgdb on SMC */
-#define CONFIG_KGDB_ON_SCC /* define if kgdb on SCC */
-#undef CONFIG_KGDB_NONE /* define if kgdb on something else */
-#define CONFIG_KGDB_INDEX 1 /* which serial channel for kgdb */
-#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port at */
-#endif
-
-#define CONFIG_BZIP2 /* include support for bzip2 compressed images */
-#undef CONFIG_WATCHDOG /* disable platform specific watchdog */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
-
-#define CONFIG_SYS_FLASH_BASE 0xFF800000
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max num of sects on one chip */
-
-#define CONFIG_SYS_DIRECT_FLASH_TFTP
-
-#if defined(CONFIG_CMD_JFFS2)
-#define CONFIG_SYS_JFFS2_FIRST_BANK 0
-#define CONFIG_SYS_JFFS2_NUM_BANKS CONFIG_SYS_MAX_FLASH_BANKS
-#define CONFIG_SYS_JFFS2_FIRST_SECTOR 0
-#define CONFIG_SYS_JFFS2_LAST_SECTOR 62
-#define CONFIG_SYS_JFFS2_SORT_FRAGMENTS
-#define CONFIG_SYS_JFFS_CUSTOM_PART
-#endif
-
-#if defined(CONFIG_CMD_I2C)
-#define CONFIG_HARD_I2C 1 /* To enable I2C support */
-#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed */
-#define CONFIG_SYS_I2C_SLAVE 0x7F /* I2C slave address */
-#endif
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256KB for Monitor */
-
-#define CONFIG_ENV_IS_IN_FLASH
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_SECT_SIZE 0x20000
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
-#endif /* CONFIG_ENV_IS_IN_FLASH */
-
-#define CONFIG_SYS_DEFAULT_IMMR 0x00010000
-
-#define CONFIG_SYS_IMMR 0xF0000000
-
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/* Hard reset configuration word */
-#define CONFIG_SYS_HRCW_MASTER 0x0C40025A /* Not used - provided by FPGA */
-/* No slaves */
-#define CONFIG_SYS_HRCW_SLAVE1 0
-#define CONFIG_SYS_HRCW_SLAVE2 0
-#define CONFIG_SYS_HRCW_SLAVE3 0
-#define CONFIG_SYS_HRCW_SLAVE4 0
-#define CONFIG_SYS_HRCW_SLAVE5 0
-#define CONFIG_SYS_HRCW_SLAVE6 0
-#define CONFIG_SYS_HRCW_SLAVE7 0
-
-#define CONFIG_SYS_MALLOC_LEN (4096 << 10) /* Reserve 4 MB for malloc() */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPUs */
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-#define CONFIG_SYS_HID0_INIT 0
-#define CONFIG_SYS_HID0_FINAL (HID0_ICE | HID0_IFEM | HID0_ABE)
-
-#define CONFIG_SYS_HID2 0
-
-#define CONFIG_SYS_SIUMCR 0x01240200
-#define CONFIG_SYS_SYPCR 0xFFFF0683
-#define CONFIG_SYS_BCR 0x00000000
-#define CONFIG_SYS_SCCR SCCR_DFBRG01
-
-#define CONFIG_SYS_RMR RMR_CSRE
-#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
-#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
-#define CONFIG_SYS_RCCR 0
-
-#define CONFIG_SYS_MPTPR 0x1300
-#define CONFIG_SYS_PSDMR 0x82672522
-#define CONFIG_SYS_PSRT 0x4B
-
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_BR (CONFIG_SYS_SDRAM_BASE | 0x00001841)
-#define CONFIG_SYS_SDRAM_OR 0xFF0030C0
-
-#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | 0x00001801)
-#define CONFIG_SYS_OR0_PRELIM 0xFF8008C2
-#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_BCSR | 0x00000801)
-#define CONFIG_SYS_OR2_PRELIM 0xFFF00864
-
-#define CONFIG_SYS_RESET_ADDRESS 0xC0000000
-
-#endif /* __CONFIG_H */
projects / u-boot.git / commitdiff