Marek Behún [Wed, 26 May 2021 12:08:25 +0000 (14:08 +0200)]
mtd: compare also with OF path and device name in get_mtd_device_nm()
The get_mtd_device_nm() function (code imported from Linux) simply
iterates all registered MTD devices and compares the given name with
all MTDs' names.
With SPI_FLASH_MTD enabled U-Boot registers a SPI-NOR as a MTD device
with name identical to the SPI flash chip name (from SPI ID table). Thus
for a board with multiple same SPI-NORs it registers multiple MTDs, but
all with the same name (such as "s25fl164k"). We do not want to change
this behaviour, since such a change could break existing boot scripts,
which can rely on a hardcoded name.
In order to allow somehow to uniqely select a MTD device, change
get_mtd_device_nm() function as such:
- if first character of name is '/', try interpreting it as OF path
- otherwise compare the name with MTDs name and MTDs device name.
In the following example a board has two "s25fl164k" SPI-NORs. They both
have name "s25fl164k", thus cannot be uniquely selected via this name.
With this change, the user can select the second SPI-NOR either with
"spi-nor@1" or "/soc/spi@10600/spi-nor@1".
Marek Behún [Wed, 26 May 2021 12:08:23 +0000 (14:08 +0200)]
mtd: probe SPI NOR devices in mtd_probe_devices()
In order for `mtd list` U-Boot command to list SPI NOR devices without
the need to run `sf probe` before, we have to probe SPI NOR devices in
mtd_probe_devices().
Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Pali Rohár <pali@kernel.org> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Tested-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Cc: Priyanka Jain <priyanka.jain@nxp.com> Cc: Simon Glass <sjg@chromium.org> Cc: Heiko Schocher <hs@denx.de> Cc: Patrick Delaunay <patrick.delaunay@st.com>
Marek Behún [Wed, 26 May 2021 12:08:22 +0000 (14:08 +0200)]
mtd: remove mtd_probe() function
The device_probe() function does the same thing as mtd_probe() and
mtd_probe() is only used in mtd_probe_uclass_mtd_devs(), where the
probing can be made simpler by using uclass_foreach_dev_probe macro.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Pali Rohár <pali@kernel.org> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Tested-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Cc: Priyanka Jain <priyanka.jain@nxp.com> Cc: Simon Glass <sjg@chromium.org> Cc: Heiko Schocher <hs@denx.de> Cc: Patrick Delaunay <patrick.delaunay@st.com>
Marek Behún [Wed, 26 May 2021 12:08:20 +0000 (14:08 +0200)]
mtd: spi-nor: allow registering multiple MTDs when DM is enabled
Currently when the SPI_FLASH_MTD config option is enabled, only one SPI
can be registered as MTD at any time - it is the last one probed (since
with old non-DM model only one SPI NOR could be probed at any time).
When DM is enabled, allow for registering multiple SPI NORs as MTDs by
utilizing the nor->mtd structure, which is filled in by spi_nor_scan
anyway, instead of filling a separate struct mtd_info.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Pali Rohár <pali@kernel.org> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Tested-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Cc: Priyanka Jain <priyanka.jain@nxp.com> Cc: Simon Glass <sjg@chromium.org> Cc: Heiko Schocher <hs@denx.de> Cc: Patrick Delaunay <patrick.delaunay@st.com>
Marek Behún [Wed, 26 May 2021 12:08:19 +0000 (14:08 +0200)]
mtd: add support for parsing partitions defined in OF
Add support for parsing partitions defined in device-trees via the
`partitions` node with `fixed-partitions` compatible.
The `mtdparts`/`mtdids` mechanism takes precedence. If some partitions
are defined for a MTD device via this mechanism, the code won't register
partitions for that MTD device from OF, even if they are defined.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Tested-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Cc: Simon Glass <sjg@chromium.org> Cc: Heiko Schocher <hs@denx.de> Cc: Patrick Delaunay <patrick.delaunay@st.com>
Jaime Liao [Mon, 7 Jun 2021 08:19:15 +0000 (16:19 +0800)]
mtd: spinand: macronix: Add support for serial NAND flash
Macronix NAND Flash devices are available in different configurations
and densities.
MX"35" means SPI NAND
MX35"UF" , UF meands 1.8V
MX35LF"2G" , 2G means 2Gbits
MX35LF2G"E4" , E4 means internal ECC and Quad I/O(x4)
MX35UF4GE4AD/MX35UF2GE4AD/MX35UF1GE4AD are 1.8V 4G/2Gbit serial
NAND flash device with 8-bit on-die ECC
https://www.mxic.com.tw/Lists/Datasheet/Attachments/7983/MX35UF4GE4AD,%201.8V,%204Gb,%20v0.00.pdf
MX35UF2GE4AC/MX35UF1GE4AC are 1.8V 2G/1Gbit serial
NAND flash device with 8-bit on-die ECC
https://www.mxic.com.tw/Lists/Datasheet/Attachments/7974/MX35UF2GE4AC,%201.8V,%202Gb,%20v1.0.pdf
Validated via normal(default) and QUAD mode by read, erase, read back,
on Xilinx Zynq PicoZed FPGA board which included Macronix
SPI Host(drivers/spi/spi-mxic.c).
Signed-off-by: Jaime Liao <jaimeliao@mxic.com.tw> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
zhengxun [Tue, 23 Mar 2021 13:16:47 +0000 (13:16 +0000)]
mtd: spi-nor-ids: Add Macronix MX66UW2G345G
The MX66UW2G345G is Macronix Flash with SINGLE and OCTAL I/O. Hence,
add SPI_NOR_OCTAL_READ flag for this flash.
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: change order of id flags] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: zhengxun <zhengxunli.mxic@gmail.com>
Tom Rini [Fri, 18 Jun 2021 17:18:29 +0000 (13:18 -0400)]
Merge tag 'u-boot-stm32-20210618' of https://source.denx.de/u-boot/custodians/u-boot-stm into next
- stm32mp157c-odyssey-som DT fixes
- stm32_qspi: Fix short data write operation
- dfu: set max_buf_size to erasesize also for NOR devices
- Fixes ethernet clock property name for STM32MP1 board
- STM32CubeProgrammer: various fixes
- clk: cosmetic update for clk-uclass
Patrick Delaunay [Tue, 18 May 2021 13:12:08 +0000 (15:12 +0200)]
stm32mp: stm32prog: handle the next phase after USB re-enumeration
Handle the second USB enumeration only when the flashlayout is received
and when phase is PHASE_FLASHLAYOUT. This patch removes the call of
stm32prog_next_phase as it is already done in stm32prog_dfu_init().
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Patrick Delaunay [Tue, 18 May 2021 13:12:07 +0000 (15:12 +0200)]
stm32mp: stm32prog: solve compilation with CONFIG_FIT_SIGNATURE
When CONFIG_FIT_SIGNATURE is activated, CONFIG_LEGACY_IMAGE_FORMAT
is deactivated and the define IMAGE_FORMAT_LEGACY don't exist with
include/image.h:
#if defined(CONFIG_LEGACY_IMAGE_FORMAT)
#define IMAGE_FORMAT_LEGACY 0x01 /* legacy image_header based format */
#endif
This patch adds the needed check on compilation flag
CONFIG_LEGACY_IMAGE_FORMAT to avoid the compilation error
for command stm32prog:
cmd_stm32prog.c:81:8: error: ‘IMAGE_FORMAT_LEGACY’ undeclared
(first use in this function); did you mean ‘IMAGE_FORMAT_FIT’?
81 | if (IMAGE_FORMAT_LEGACY ==
| ^~~~~~~~~~~~~~~~~~~
| IMAGE_FORMAT_FIT
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Patrick Delaunay [Tue, 18 May 2021 13:12:06 +0000 (15:12 +0200)]
stm32mp: stm32prog: add support of initrd in flashlayout
Add the support in command stm32prog of kernel load and start
with initrd file, identify by the partition Type "Binary" in
the flashlayout.tsv, for example:
- 0x01 fsbl Binary none 0x0 tfa.stm32
- 0x03 fip Binary none 0x0 fip.bin
P 0x10 kernel System ram0 0xC2000000 uImage.bin
P 0x11 dtb FileSystem ram0 0xC4000000 board.dtb
P 0x12 initrd Binary ram0 0xC4400000 <initrd>
The <initrd> file can be a legacy image "uInitrd", generated
with mkimage, or a RAW initrd image "initrd.gz".
After a DFU detach the bootm command with be executed
with the associated address, for example:
$> bootm 0xC2000000 0xC4400000:<size> 0xC4000000
When the "Binary" partition type is absent, the 'bootm'
command starts the kernel without ramdisk, for example:
$> bootm 0xC2000000 - 0xC4000000
With this paths, it is no more mandatory to generate FIT
including the kernel, DT and initrd:
- 0x01 fsbl Binary none 0x0 tfa.stm32
- 0x03 fip Binary none 0x0 fip.bin
P 0x10 fit System ram0 0xC2000000 fit.bin
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Patrick Delaunay [Tue, 18 May 2021 13:12:04 +0000 (15:12 +0200)]
stm32mp: stm32prog: remove all the header check for UART download
This patch removes the header check for UART download;
the check of checksum is not mandatory with even parity and chuck
checksum for each 256 received bytes and it is only done for
STM32 image (FSBL = TF-A BL2), not for FIT image.
This patch solve issue of duplicated 0x100 byte written with FIP header.
board: stm32mp1: correct the property name for eth
Use the correct name for STMicroelectronics phys config properties,
replace '_' by '-':
"st,eth_clk_sel" => "st,eth-clk-sel"
"st,eth-ref-clk-sel" => st,eth-clk-sel"
These property name are aligned with the upstreamed Linux kernel binding:
linux/Documentation/devicetree/bindings/net/stm32-dwmac.yaml
See Linux kernel commit "dt-bindings: net: stmmac: add phys config
properties" merged in v5.1-rc1.
This patch allow to reuse the kernel device tree directly in U-Boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
dfu: dfu_mtd: set max_buf_size to erasesize also for NOR devices
For NOR devices the logical DFU buffer size is the sector_size,
as it is done in dfu_sf.c or in spi/sf_mtd.c
(sf_mtd_info.erasesize = flash->sector_size)
For NAND the DFU size was already limited to erasesize as
has_pages = true.
So the mtd dfu backend can use this erasesize for all the MTD devices,
NOR and NAND with dfu->max_buf_size = mtd->erasesize
This difference was initially copied from MTD command, where
data is fully available in RAM without size limitation.
This patch avoids to have many sector write in dfu_mtd.c at the end
of the DFU transfer and avoids issues with USB timeout or WATCHDOG.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Daniil Stas [Sun, 23 May 2021 22:24:49 +0000 (22:24 +0000)]
spi: stm32_qspi: Fix short data write operation
TCF flag only means that all data was sent to FIFO. To check if the
data was sent out of FIFO we should also wait for the BUSY flag to be
cleared. Otherwise there is a race condition which can lead to
inability to write short (one byte long) data.
Signed-off-by: Daniil Stas <daniil.stas@posteo.net> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Yifeng Zhao [Mon, 7 Jun 2021 08:40:29 +0000 (16:40 +0800)]
mtd: nand: NFC drivers for RK3308, RK2928 and others
This driver supports Rockchip NFC (NAND Flash Controller) found on
RK3308, RK2928, RKPX30, RV1108 and other SOCs. The driver has been
tested using 8-bit NAND interface on the ARM based RK3308 platform.
Support Rockchip SoCs and NFC versions:
- PX30 and RK3326(NFCv900).
ECC: 16/40/60/70 bits/1KB.
CLOCK: ahb and nfc.
- RK3308 and RV1108(NFCv800).
ECC: 16 bits/1KB.
CLOCK: ahb and nfc.
- RK3036 and RK3128(NFCv622).
ECC: 16/24/40/60 bits/1KB.
CLOCK: ahb and nfc.
- RK3066, RK3188 and RK2928(NFCv600).
ECC: 16/24/40/60 bits/1KB.
CLOCK: ahb.
Supported features:
- Read full page data by DMA.
- Support HW ECC(one step is 1KB).
- Support 2 - 32K page size.
- Support 8 CS(depend on SoCs)
Limitations:
- No support for the ecc step size is 512.
- Untested on some SoCs.
- No support for subpages.
- No support for the builtin randomizer.
- The original bad block mask is not supported. It is recommended to
use the BBT(bad block table).
Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Anand Moon [Sat, 5 Jun 2021 14:38:43 +0000 (14:38 +0000)]
pci: pcie_dw_rockchip: Replace msleep occurences by udelay
Replace msleep occurences by udelay.
drivers/pci/pcie_dw_rockchip.c:254:3: warning: implicit
declaration of function 'msleep' [-Wimplicit-function-declaration]
Cc: Patrick Wildt <patrick@blueri.se> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Kever Yang <kever.yang@rock-chips.com> Signed-off-by: Anand Moon <linux.amoon@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Anand Moon [Sat, 5 Jun 2021 14:38:41 +0000 (14:38 +0000)]
pci: pcie_dw_rockchip: Fixed the below compilation error
Use the generic error number instead of specific error number.
Changes fix the below error.
drivers/pci/pcie_dw_rockchip.c: In function 'rk_pcie_read':
drivers/pci/pcie_dw_rockchip.c:70:10: error: 'PCIBIOS_UNSUPPORTED'
undeclared (first use in this function)
70 | return PCIBIOS_UNSUPPORTED;
| ^~~~~~~~~~~~~~~~~~~
drivers/pci/pcie_dw_rockchip.c: In function 'rk_pcie_write':
drivers/pci/pcie_dw_rockchip.c:90:10: error: 'PCIBIOS_UNSUPPORTED'
undeclared (first use in this function)
90 | return PCIBIOS_UNSUPPORTED;
| ^~~~~~~~~~~~~~~~~~~
Cc: Patrick Wildt <patrick@blueri.se> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Patrick Wildt <patrick@blueri.se> Signed-off-by: Anand Moon <linux.amoon@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
arm: dts: stm32mp157c-odyssey-som: set the SDMMC2 VQMMC supply
Set the SDMMC2 VQMMC supply to vdd (buck3). Note that in the
corresponding Linux kernel device tree, the supply is set to v3v3
(buck4), which is wrong.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
arm: dts: stm32mp157c-odyssey-som: fix the basic SDMMC2 properties
The SDMMC2 interface hosts an eMMC. Replace the interface properties
that would only apply to SD cards—“broken-cd” and “disable-wp”—with
relevant ones: “non-removable”, “no-sd” and “no-sdio”.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tom Rini [Thu, 17 Jun 2021 15:46:44 +0000 (11:46 -0400)]
Merge tag 'u-boot-atmel-2021.10-a' of https://source.denx.de/u-boot/custodians/u-boot-atmel into next
First set of u-boot-atmel features for the 2021.10 cycle:
This feature set converts the boards pm9261 and pm9263 Ethernet support
to DM; enables hash command for all SAM boards; fixes the NAND pmecc
bit-flips correction; adds Falcon boot for sama5d3_xplained board; and
other minor adjustments.
Sean Anderson [Fri, 11 Jun 2021 04:16:16 +0000 (00:16 -0400)]
k210: Don't imply CCF
Now that the k210 clock driver does not depend on CCF, we should no longer
imply it (and probably should not have in the first place). We can also
reduce the pre-relocation malloc arena back to something sensible.
Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Sean Anderson [Fri, 11 Jun 2021 04:16:11 +0000 (00:16 -0400)]
clk: k210: Re-add support for setting rate
This adds support for setting clock rates, which was left out of the
initial CCF expunging. There are several tricky bits here, mostly related
to the PLLS:
* The PLL's bypass is broken. If the PLL is reconfigured, any child clocks
will be stopped.
* PLL0 is the parent of ACLK which is the CPU and SRAM's clock. To prevent
stopping the CPU while we configure PLL0's rate, ACLK is reparented
to IN0 while PLL0 is disabled.
* PLL1 is the parent of the AISRAM clock. This clock cannot be reparented,
so we instead just disallow changing PLL1's rate after relocation (when
we are using the AISRAM).
Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Sean Anderson [Fri, 11 Jun 2021 04:16:09 +0000 (00:16 -0400)]
clk: k210: Move pll into the rest of the driver
Now that there no separate PLL driver, we can no longer make the PLL
functions static. By moving the PLL driver in with the rest of the clock
code, we can make these functions static again. We still keep the pll
header for unit testing, but it is pretty reduced.
Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Sean Anderson [Fri, 11 Jun 2021 04:16:08 +0000 (00:16 -0400)]
clk: k210: Rewrite to remove CCF
This is effectively a complete rewrite to remove all dependency on CCF.
The code is now smaller, and so is the binary. It also takes up less memory
at runtime (since we don't have to create 40 udevices). In general, I am
much happier with this driver as much of the complexity and late binding
has been removed.
The k210_*_params structs which were previously used to initialize CCF
clocks are now used as the complete configuration. Since we can write our
own division logic, we can now do away with several "half" clocks which
only existed to provide constant factors of two.
The clock IDs have been renumbered to remove unused clocks. This may not be
the last time they are renumbered, since we have diverged with Linux. There
are also still a few clocks left out which may need to be added back in.
In general, I have tried to leave out behavioral changes. However, there is
a small bugfix regarding ACLK. According to the technical reference manual,
its mux comes *after* its divider (which is present only for PLL0). This
would have required yet another intermediate clock to fix with CCF, but
with the new driver it is just 2 lines of code :)
Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Sean Anderson [Fri, 11 Jun 2021 04:16:07 +0000 (00:16 -0400)]
clk: Allow force setting clock defaults before relocation
Since 291da96b8e ("clk: Allow clock defaults to be set during re-reloc
state for SPL only") it has been impossible to set clock defaults before
relocation. This is annoying on boards without SPL, since there is no way
to set clock defaults before U-Boot proper. In particular, the aisram rate
must be changed before relocation on the K210, since U-Boot will hang if we
try and change the rate while we are using aisram.
To get around this, extend the stage parameter to allow force setting
defaults, even if they would be otherwise postponed for later. A device
tree property was decided against because of the concerns in the original
commit thread about the overhead of repeatedly parsing the device tree.
Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
This supports Falcon boot support for Microchip SAMA5D3 Xplained,
tested on raw MMC, and on raw NAND.
spl_start_uboot() is has the simplest possible implementation.
It doesn't test the environment because enabling environment support
currently causes the SPL to exceed its maximum size (64 KiB).
It doesn't check the serial for incoming characters either because
this functionality currently doesn't seem to work from the SPL
on this board.
Settings for Falcon boot from at FAT partition are also added to
avoid compile failures when CONFIG_SPL_OS_BOOT is enabled, but this
particular case is currently not functional as adding FAT and
partition support cause the SPL to be too big again.
Signed-off-by: Michael Opdenacker <michael.opdenacker@bootlin.com>
dma: ti: k3-udma: Add support for native configuration of chan/flow
In absence of Device Manager (DM) services such as at R5 SPL stage,
driver will have to natively setup TCHAN/RCHAN/RFLOW cfg registers.
Add support for the same.
Note that we still need to send chan/flow cfg message to TIFS via TISCI
client driver in order to open up firewalls around chan/flow but setting
up of cfg registers is handled locally.
U-Boot specific code is in a separate file included in main driver so
as to maintain similarity with kernel driver in order to ease porting of
code in future.
soc: ti: k3-navss-ringacc: Add support for native configuration of rings
In absence of Device Manager (DM) services such as at R5 SPL stage,
driver will have to natively setup Ring Cfg registers. Add support for
the same.
Note that we still need to send RING_CFG message to TIFS via TISCI
client driver in order to open up firewalls around Rings.
U-Boot specific code is in a separate file included in main driver so
as to maintain similarity with kernel driver in order to ease porting of
code in future.
ARM: dts: k3: Add cfg register space for ringacc and udmap
R5 SPL needs access to cfg space of Rings and UDMAP, therefore add RING
CFG, TCHAN CFG and RCHAN CFG address ranges.
Note that these registers are present within respective IPs but are
not populated in Linux DT nodes (as they are configured via TISCI APIs)
and hence are added to -u-boot.dtsi for now.
firmware: ti_sci: Add support for Resoure Management at R5 SPL stage.
On J721e and J7200, MCU R5 core (boot master) itself would run Device
Manager (DM) Firmware and interact with TI Foundational Security (TIFS)
firmware to enable DMA and such other Resource Management (RM) services.
So, during R5 SPL stage there is no such RM service available and ti_sci
driver will have to directly interact with TIFS using DM to DMSC
channels to request RM resources.
Therefore add DT binding and driver for the same. This driver will
handle Resource Management services at R5 SPL stage.
firmware: ti_sci: Implement GET_RANGE with static data
In case of R5 SPL, GET_RANGE API service is not available (as DM
services are not yet up), therefore service such calls locally using
per SoC static data.
Tero Kristo [Fri, 11 Jun 2021 08:45:27 +0000 (11:45 +0300)]
arm: dts: k3-j72xx: correct MCU timer1 frequency
MCU timer1 is used as the tick timer for MCU R5 SPL, and the
clock-frequency defined in DT appears to be incorrect at the moment.
Actual clock source for the timer is MCU_SYSCLK0 / 4 which is 250MHz.
Earlier setup of 25MHz went unnoticed, as there was a separate issue
with omap-timer, which caused an error to the clock by a factor of 8
with j7 devices. This problem surfaced once the omap-timer was fixed.
Tero Kristo [Fri, 11 Jun 2021 08:45:26 +0000 (11:45 +0300)]
board: ti: j72xx: README: update build instructions and image formats
Update build instructions and image formats based on HSM rearch. A new
DM image is added into the build, which gets executed right after R5
SPL finishes its job.
Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tero Kristo <kristo@kernel.org>
Dave Gerlach [Fri, 11 Jun 2021 08:45:25 +0000 (11:45 +0300)]
configs: j7200_evm_r5: Enable raw access power management features
Sysfw is not going to provide access to power management features in the
new architecture, so SPL must implement these itself. Enable all the raw
register access based clock + power domain drivers.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Tero Kristo <kristo@kernel.org>
Tero Kristo [Fri, 11 Jun 2021 08:45:24 +0000 (11:45 +0300)]
configs: j721e_evm_r5: Enable raw access power management features
Sysfw is not going to provide access to power management features in the
new architecture, so SPL must implement these itself. Enable all the raw
register access based clock + power domain drivers.
Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tero Kristo <kristo@kernel.org>
Dave Gerlach [Fri, 11 Jun 2021 08:45:23 +0000 (11:45 +0300)]
arm: mach-k3: j721e_init: Force early probe of clk-k3 driver
Force the clk-k3 driver to probe early during R5 SPL boot to ensure the
default system clock configuration is completed. Many other drivers
assume a default state of the clock tree and it is currently possible
for them to probe before clk-k3 depending on the exact system
configuration.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Reported-by: Keerthy <j-keerthy@ti.com> Tested-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Tero Kristo <kristo@kernel.org>
Tero Kristo [Fri, 11 Jun 2021 08:45:22 +0000 (11:45 +0300)]
arm: mach-k3: sysfw-loader: pass boardcfg to sciserver
Copy the contents of the board config loaded from sysfw.itb into an
EXTBOOT shared memory buffer that gets passed to sciserver. This only
needs to be done if EXTBOOT area has not been populated by ROM code yet.
Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tero Kristo <kristo@kernel.org>
Tero Kristo [Fri, 11 Jun 2021 08:45:20 +0000 (11:45 +0300)]
arm: mach-k3: do board config for PM only if supported
If the raw PM support is built in, we are operating in the split
firmware approach mode where PM support is not available. In this
case, skip the board config for this.
Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tero Kristo <kristo@kernel.org>
Dave Gerlach [Fri, 11 Jun 2021 08:45:18 +0000 (11:45 +0300)]
arm: mach-k3: Add platform data for j721e and j7200
Add platform clock and powerdomain data for J721e and J7200. This data
is used by the corresponding drivers to register all the required device
clocks and powerdomains.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Tero Kristo <kristo@kernel.org>
Tero Kristo [Fri, 11 Jun 2021 08:45:17 +0000 (11:45 +0300)]
tools: k3_fit_atf: add DM binary to the FIT image
Add DM (device manager) firmware image to the fit image that is loaded by
R5 SPL. This is needed with the HSM rearch where the firmware allocation
has been changed slightly.
Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tero Kristo <kristo@kernel.org>
Tero Kristo [Fri, 11 Jun 2021 08:45:16 +0000 (11:45 +0300)]
cmd: ti: pd: Add debug command for K3 power domains
Add support command for debugging K3 power domains. This is useful with
the HSM rearch setup, where power domains are directly controlled by SPL
instead of going through the TI SCI layer. The debugging support is only
available in the u-boot codebase though, so the raw register access
power domain layer must be enabled on u-boot side for this to work. By
default, u-boot side uses the TI SCI layer, and R5 SPL only uses the
direct access methods.
Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tero Kristo <kristo@kernel.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Tero Kristo [Fri, 11 Jun 2021 08:45:15 +0000 (11:45 +0300)]
power: domain: Introduce driver for raw TI K3 PDs
Normally, power domains are handled via TI-SCI in K3 SoCs. However,
SPL is not going to have access to sysfw resources, so it must control
them directly. Add driver for supporting this.
Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tero Kristo <kristo@kernel.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Tero Kristo [Fri, 11 Jun 2021 08:45:14 +0000 (11:45 +0300)]
clk: add support for TI K3 SoC clocks
Add driver to support TI K3 generation SoC clocks. This driver registers
the clocks provided via platform data, and adds support for controlling
the clocks via DT handles.
Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tero Kristo <kristo@kernel.org>
Tero Kristo [Fri, 11 Jun 2021 08:45:13 +0000 (11:45 +0300)]
clk: add support for TI K3 SoC PLL
Add support for TI K3 SoC PLLs. This clock type supports
enabling/disabling/setting and querying the clock rate for the PLL. The
euclidean library routine is used to calculate divider/multiplier rates
for the PLLs.
Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tero Kristo <kristo@kernel.org>
Tero Kristo [Fri, 11 Jun 2021 08:45:12 +0000 (11:45 +0300)]
clk: fix set_rate to clean up cached rates for the hierarchy
Clock rates are cached within the individual clock nodes, and right now
if one changes a clock rate somewhere in the middle of the tree, none
of its child clocks notice the change. To fix this, clear up all the
cached rates for us and our child clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tero Kristo <kristo@kernel.org>
Tero Kristo [Fri, 11 Jun 2021 08:45:11 +0000 (11:45 +0300)]
clk: fix assigned-clocks to pass with deferring provider
If a clock provider is not ready for assigning default rates/parents
during its probe, it may return -EPROBE_DEFER directly from xlate.
Handle this special case properly by skipping the entry and adjusting the
return value to pass. The defaults will be handled properly in post probe
phase then.
Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tero Kristo <kristo@kernel.org>
Tero Kristo [Fri, 11 Jun 2021 08:45:09 +0000 (11:45 +0300)]
clk: add support for setting clk rate from cmdline
Add new clk subcommand "clk setfreq", for setting up a clock rate
directly from u-boot cmdline. This is handy for any debugging purposes
towards clocks.
Acked-by: Lukasz Majewski <lukma@denx.de> Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tero Kristo <kristo@kernel.org>
Tero Kristo [Fri, 11 Jun 2021 08:45:07 +0000 (11:45 +0300)]
clk: fix clock tree dump to properly dump out every registered clock
Some clocks are not associated to a DM node, so just parsing the DM is not
enough. This is especially true for root clocks, which typically don't have
any parents. Instead, fetch every registered UCLASS_CLK instance, and dump
these out.
Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tero Kristo <kristo@kernel.org>
Tero Kristo [Fri, 11 Jun 2021 08:45:06 +0000 (11:45 +0300)]
clk: fixed_rate: add API for directly registering fixed rate clocks
Current driver only supports registering fixed rate clocks from DT. Add
new API which makes it possible to register fixed rate clocks directly
from e.g. platform specific clock drivers.
Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tero Kristo <kristo@kernel.org>
Lokesh Vutla [Fri, 11 Jun 2021 08:45:05 +0000 (11:45 +0300)]
common: fit: Update board_fit_image_post_process() to pass fit and node_offset
board_fit_image_post_process() passes only start and size of the image,
but type of the image is not passed. So pass fit and node_offset, to
derive information about image to be processed.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Tero Kristo <kristo@kernel.org>
Tero Kristo [Fri, 11 Jun 2021 08:45:04 +0000 (11:45 +0300)]
remoteproc: k3-r5: remove sysfw PM calls if not supported
With the sysfw rearch, sysfw PM calls are no longer available from SPL
level. To properly support this, remove the is_on checks and the reset
assertion from the R5 remoteproc driver as these are not supported.
Attempting to access unavailable services will cause the device to hang.
Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tero Kristo <kristo@kernel.org>
Tero Kristo [Fri, 11 Jun 2021 08:45:03 +0000 (11:45 +0300)]
arm: mach-k3: introduce new config option for sysfw split
On J7 family of SoCs (J721E and J7200), sysfw is being split to be run
under two cores, TIFS portion on DMSC core, and DM firmware under MCU
R5. As MCU R5 is also used to run one phase of the bootloader, we must
prevent access from here towards sysfw services. To support this, add
new config option which can be used to detect presence of RM/PM sysfw
services.
Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tero Kristo <kristo@kernel.org>
Tero Kristo [Fri, 11 Jun 2021 08:45:02 +0000 (11:45 +0300)]
lib: rational: copy the rational fraction lib routines from Linux
Copy the best rational approximation calculation routines from Linux.
Typical usecase for these routines is to calculate the M/N divider
values for PLLs to reach a specific clock rate.
This is based on linux kernel commit:
"lib/math/rational.c: fix possible incorrect result from rational
fractions helper"
(sha1: 323dd2c3ed0641f49e89b4e420f9eef5d3d5a881)
Signed-off-by: Tero Kristo <t-kristo@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Tero Kristo <kristo@kernel.org>
Dario Binacchi [Wed, 2 Jun 2021 20:38:04 +0000 (22:38 +0200)]
rtc: davinci: add driver model support
Update the driver to support the device tree and the driver model.
The read / write helpers in rtc_ops allow access to scratch registers
only. The offset parameter is added to the address of the scratch0
register.
Support for non-DM has been removed as there were no users.
Dario Binacchi [Wed, 2 Jun 2021 20:38:02 +0000 (22:38 +0200)]
rtc: davinci: use unlock/lock mechanism
The RTC module contains a kicker mechanism to prevent any spurious
writes from changing the register values. To set the time, you must
first unlock the TC registers, update them and then lock.
Dario Binacchi [Wed, 2 Jun 2021 20:38:01 +0000 (22:38 +0200)]
rtc: davinci: check BUSY bit before set TC registers
To write correct data to the TC registers, the STATUS register must be
read until the BUSY bit is equal to zero. Once the BUSY flag is zero,
there is a 15 μs access period in which the TC registers can be
programmed.
The rtc_wait_not_busy() has been inspired by the Kernel.
projects / u-boot.git / log
