The changes here aren't quite right, and on platforms such as Raspberry
Pi where we can have both serial and video output, the change above
causes output to change. This can be seen as the hush tests we have now
fail.
Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 10 Mar 2023 20:48:51 +0000 (12:48 -0800)]
buildman: Fix CROSS_COMPILE output for sandbox
The previous attempt at fixing this broke the normal usage of the -A
flag.
At present, 'buildman -A sandbox' adds the path containing the
toolchain. We can assume that this is in the path and we don't want to
set CROSS_COMPILE=/bin/
Change this to align with what MakeEnvironment() does, but only for
sandbox boards.
Roman Kopytin [Wed, 8 Mar 2023 01:13:41 +0000 (01:13 +0000)]
tools: add fdt_add_pubkey
Having to use the -K option to mkimage to populate U-Boot's .dtb with the
public key while signing the kernel FIT image is often a little
awkward. In particular, when using a meta-build system such as
bitbake/Yocto, having the tasks of the kernel and U-Boot recipes
intertwined, modifying deployed artifacts and rebuilding U-Boot with
an updated .dtb is quite cumbersome. Also, in some scenarios one may
wish to build U-Boot complete with the public key(s) embedded in the
.dtb without the corresponding private keys being present on the same
build host.
So this adds a simple tool that allows one to disentangle the kernel
and U-Boot builds, by simply copy-pasting just enough of the mkimage
code to allow one to add a public key to a .dtb. When using mkimage,
some of the information is taken from the .its used to build the
kernel (algorithm and key name), so that of course needs to be
supplied on the command line.
Signed-off-by: Roman Kopytin <Roman.Kopytin@kaspersky.com> Signed-off-by: Ivan Mikhaylov <fr0st61te@gmail.com> Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Cc: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Ivan Mikhaylov [Wed, 8 Mar 2023 01:13:40 +0000 (01:13 +0000)]
binman: add tests for sign option
Add the test which provides sequence of actions:
1. create the image from binman dts
2. create public and private keys
3. add public key into dtb with fdt_add_pubkey
4. 1. sign FIT container with new sign option with extracting from
image
2. sign exact FIT container with replacing of it in image
5. check with fit_check_sign
Signed-off-by: Ivan Mikhaylov <fr0st61te@gmail.com>
Renumber test file from 277 to 280;
Move UpdateSignatures() to Entry base class;
Don't allow missing mkimage as it doesn't make sense;
Propagate --toolpath for CI;
Call mark_build_done() to avoid regenerating FIT: Signed-off-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Thu, 2 Mar 2023 03:08:44 +0000 (04:08 +0100)]
test: cmd: fdt: Test fdt apply
Add 'fdt chosen' test which works as follows:
- Create basic DT, map it to sysmem
- Apply DTO which adds single property via fragment (without address spec)
- Apply DTO which adds more properties (string, u32, empty) and a subnode,
with phandle via frament@0 and thus tests /__symbols__ node
- Apply DTO which modifies property of the previous DTO via phandle and thus
tests the /__fixups__ node
- Print modified DT, verify it contains updates from DTOs
The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Thu, 2 Mar 2023 03:08:43 +0000 (04:08 +0100)]
test: cmd: fdt: Test fdt chosen
Add 'fdt chosen' test which works as follows:
- Create basic DT, map it to sysmem
- Print /chosen node, verify it is nonexistent
- Create chosen node
- Print /chosen node, verify it contains only version
- Create /chosen node with initrd entries
- Print /chosen node, verify it contains version and initrd entries
The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Thu, 2 Mar 2023 03:08:42 +0000 (04:08 +0100)]
test: cmd: fdt: Test fdt rsvmem
Add 'fdt rsvmem' test which works as follows:
- Create custom FDT with single reserved memory (rsvmem) entry, map it to sysmem
- Add new rsvmem entry
- Delete existing older rsvmem entry
- Add new rsvmem entry again
- Always print the rsvmem list and validate it
The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Thu, 2 Mar 2023 03:08:41 +0000 (04:08 +0100)]
test: cmd: fdt: Test fdt memory
Add 'fdt memory' test which works as follows:
- Create custom FDT with /memory node, with select #*cells, map it to sysmem
- Perform memory fixup
- Read back the /memory node and validate its content
The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Thu, 2 Mar 2023 03:08:39 +0000 (04:08 +0100)]
test: cmd: fdt: Test fdt header
Add 'fdt header' test which works as follows:
- Create basic FDT, map it to sysmem
- Print the FDT header
- Get all members of the FDT header into variable and
verify the variables contain correct data
The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Merged in test: cmd: fdt: Drop unused fdt_test_header_get() fdt parameter: Signed-off-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Thu, 2 Mar 2023 03:08:32 +0000 (04:08 +0100)]
test: cmd: fdt: Test fdt print and list
Add 'fdt print' and 'fdt list' test which works as follows:
- Create fuller FDT, map it to sysmem
- Print the entire FDT, parts of the FDT and select properties
- Compare output from the print or list
The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Thu, 2 Mar 2023 03:04:40 +0000 (04:04 +0100)]
cmd: fdt: Drop the 0x prefix
The 'fdt get addr' is always assumed to be hex value, drop the prefix.
Since this might break existing users who depend on the existing
behavior with 0x prefix, this is a separate patch. Revert if this
breaks anything.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Marek Vasut [Mon, 27 Feb 2023 19:55:39 +0000 (20:55 +0100)]
console: Use only 0x00 as line separator for console recording
In case character 0x20 (space) is used as line separator,
character 0x9 (tab) is treated end of line. Commands which
output a lot of tabs, i.e. various tree printing commands
like 'fdt print' then end up generating a lot of newlines
in the recorded output, and the recorded output is corrupted.
Use character 0x00 (NUL) as separator instead to treat the
tabs as valid part of recorded line.
Suggested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Fri, 10 Mar 2023 03:33:13 +0000 (04:33 +0100)]
test: Wrap assert macros in ({ ... }) and fix missing semicolons
Wrap the assert macros in ({ ... }) so they can be safely used both as
right side argument as well as in conditionals without curly brackets
around them. In the process, find a bunch of missing semicolons, fix
them.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Ioana Ciornei [Tue, 28 Feb 2023 16:32:10 +0000 (18:32 +0200)]
arch: arm: dst: fsl-ls2080a.dts: sync serial nodes with Linux
Sync the serial nodes of the LS208XA RDB/QDS boards with their
representation in Linux. We also imported the clockgen and sysclk nodes
which are dependencies.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Ioana Ciornei [Tue, 28 Feb 2023 16:32:08 +0000 (18:32 +0200)]
arch: arm: dst: fsl-ls2080a.dtsi: add an 'soc' node
The u-boot dts for these boards do not have an soc node, unlike its
Linux counterpart. This patch just adds the soc node as seen in Linux,
the next patches will move some nodes under it.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
The LX2160ARDB board has support for DM_ETH probed devices, which means
that we do not need to manually create an MDIO controller, register it,
create PHYs on it etc.
In order to cleanup the board file a bit, just remove this code entirely.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Masahisa Kojima [Tue, 21 Feb 2023 02:33:17 +0000 (11:33 +0900)]
efi_loader: update SetVariable attribute check
UEFI specification v2.10 says that
EFI_VARIABLE_AUTHENTICATED_WRITE_ACCESS is deprecated and
EFI_UNSUPPORTED should be returned in SetVariable variable service.
Current implementation returns EFI_INVALID_PARAMETER,
let's fix the return value.
Together with above change, this commit also updates the SetVariable
attribute check to be aligned with the EDK2 reference implementation.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org> Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Simon Glass [Fri, 10 Mar 2023 20:47:21 +0000 (12:47 -0800)]
video: Clear the vidconsole rather than the video
It is better to clear the console device rather than the video device,
since the console has the text display. We also need to reset the cursor
position with the console, but not with the video device.
Add a new function to handle this and update the 'cls' command to use it.
Simon Glass [Fri, 10 Mar 2023 20:47:17 +0000 (12:47 -0800)]
video: Allow a copy framebuffer with pre-allocated fb
At present it is not possible for the video driver to use a pre-allocated
frame buffer (such as is done with EFI) with the copy framebuffer. This
can be useful to speed up the display.
Adjust the implementation so that copy_size can be set to the required
size, with this being allocated if the normal framebuffer size is 0.
Simon Glass [Fri, 10 Mar 2023 20:47:15 +0000 (12:47 -0800)]
efi: Use a fixed value for the timer clock
It is not yet clear how to read the timer via EFI. The current value seems
much too high on a Framework laptop I tried. Adjust it to a lower
hard-coded value for now.
Ovidiu Panait [Sat, 11 Mar 2023 17:38:38 +0000 (19:38 +0200)]
microblaze: drop remnants of manual reloc
Runtime relocation has been made the default for microblaze, so do the
following cleanups:
- drop all manual reloc codepaths in start.S
- drop all STATIC_RELA ifdefs, as it is now enabled unconditionally in
Kconfig
Ovidiu Panait [Sat, 11 Mar 2023 17:38:37 +0000 (19:38 +0200)]
microblaze: drop CONFIG_NEEDS_MANUAL_RELOC
Microblaze and m68k are the only remaining architectures that still enable
CONFIG_NEEDS_MANUAL_RELOC by default.
Microblaze has had runtime relocation support using CONFIG_STATIC_RELA for
quite some time, since commit d58c007498 ("microblaze: Add support for run
time relocation"). Drop support for CONFIG_NEEDS_MANUAL_RELOC and make
runtime relocation the default, as the rest of the architectures do.
Ovidiu Panait [Sat, 11 Mar 2023 17:38:36 +0000 (19:38 +0200)]
tools: relocate-rela: add support for handling 32-bit big endian files
Currently, a microblaze build with CONFIG_SYS_BIG_ENDIAN=y and
CONFIG_STATIC_RELA=y fails with:
tools/relocate-rela: Not supported machine type
ELF decoding failed
make[2]: *** [u-boot/Makefile:1306: u-boot-nodtb.bin] Error 1
To fix this, convert the 32-bit codepath to use the previously added
elf{16,32}_to_cpu() functions. The aarch64 codepath is left untouched.
This commit ensures that CI doesn't fail for the next patches which enable
runtime relocation by default for microblaze.
Tam Nguyen [Mon, 27 Feb 2023 22:58:48 +0000 (23:58 +0100)]
ARM: dts: renesas: Enable sysinfo on R-Car D3 Draak
Enable support for sysinfo on R-Car D3 Draak board. The sysinfo is used
e.g. to access and decode board-specific information and then in turn
used by board-info to print those information.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Drop compatible from I2C node, this is in r8a77995.dtsi already.
Drop status = "okay" from EEPROM node.
Add dts: tag.
Fix Kconfig EEPROM address to be 0x50 and match the DT, sync config.]
Tam Nguyen [Mon, 27 Feb 2023 22:58:47 +0000 (23:58 +0100)]
ARM: dts: renesas: Enable sysinfo on R-Car V3H Condor/Condor-I
Add new sysinfo IDs for R-Car V3H Condor/Condor-I .
Enable support for sysinfo on R-Car V3H Condor/Condor-I. The sysinfo is
used e.g. to access and decode board-specific information and then in
turn used by board-info to print those information.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Drop compatible from I2C node, this is in r8a77980.dtsi already.
Drop status = "okay" from EEPROM node.
Add dts: tag.
Update the commit message, note the new sysinfo IDs.
Fix Kconfig EEPROM address to be 0x50 and match the DT, sync config.]
Tam Nguyen [Mon, 27 Feb 2023 22:58:46 +0000 (23:58 +0100)]
sysinfo: rcar3: Fix Draak and Eagle board code
Correct the board code ID based on the hardware documentation
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Marek Vasut [Tue, 28 Feb 2023 21:16:02 +0000 (22:16 +0100)]
clk: renesas: Always select DM_RESET to prevent inobvious failure of rst_gen3 subdriver
The CLK_RCAR_GEN3 registers two subdrivers, clk_gen3 and rst_gen3.
The former depends on the clock framework, which is always enabled
in this context of clock framework driver, while the later depends
on reset framework which may not always be enabled.
Ensure the reset framework is also always enabled to prevent inobvious
early boot time bind failure of the CPG driver, which leads to system
showing no activity and is difficult to debug.
Note that one possible approach to debug this is to use CONFIG_DEBUG_UART
and add debug printascii()s into the drivers/clk/renesas/clk-rcar-gen3.c .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
In case one of the calls in probe fail, trigger a fail path and
undo all the steps done in probe until the point of failure.
The current implementation failed to stop controller clock and
free claimed clock, so fix that. Furthermore, print return code
in error prints for easier debugging.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The prior stage bootloader might have left the SDnCKCR register in completely
arbitrary state before passing control to U-Boot, which includes the register
being populated with incorrect values. Currently the SDHI driver will attempt
to use clock framework to configure SDn clock, which may fail in case SDnCKCR
contains invalid values for the SDnH clock, because the clock framework would
not be able to determine SDnH clock rate and would get -EINVAL instead, which
in turn would not allow the clock framework to determine the correct SDn clock
divider ratio.
This failure occurs specifically in case SDnCKCR reads back 0x209 .
Correct the problem by first setting default SDnH clock rate to 800 MHz, thus
assuring the SDnCKCR SDnH bits are correct, and only afterward set up the SDn
clock rate to default 200 MHz.
Note that the SDHI driver may reconfigure SDnH clock later based on IOS
settings obtained from the attached card, the 800 MHz set up here is only
the default value.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This configuration setting is only relevant if the board supports USB.
It should not be in the main menu but in the USB menu.
The setting is only relevant in USB host mode.
Fixes: 5454dea3137d ("usb: hub: allow to increase HUB_DEBOUNCE_TIMEOUT") Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
USB hubs run in host mode not in gadget mode. Hence, compiling usb_hub.c
should not be selected by CONFIG_USB_GADGET.
Suggested-by: Marek Vasut <marex@denx.de> Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Marek Vasut <marex@denx.de>
Marek Vasut [Thu, 2 Mar 2023 03:08:40 +0000 (04:08 +0100)]
test: cmd: fdt: Test fdt bootcpu
Add 'fdt bootcpu' test which works as follows:
- Create basic FDT, map it to sysmem
- Print the FDT bootcpu
- Set the FDT bootcpu and read the value back using 'fdt header get'
- Perform the previous step twice to validate bootcpu overwrite
The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Thu, 2 Mar 2023 03:08:38 +0000 (04:08 +0100)]
test: cmd: fdt: Test fdt rm
Add 'fdt rm' test which works as follows:
- Create fuller FDT, map it to sysmem
- Selectively delete nodes or properties by both path and aliases
- Verify created nodes or properties using fdt print command
The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Thu, 2 Mar 2023 03:08:37 +0000 (04:08 +0100)]
test: cmd: fdt: Test fdt mknode
Add 'fdt mknode' test which works as follows:
- Create fuller FDT, map it to sysmem
- Create node either in / or subnode
- Attempt to create node over existing node, which fails
- Attempt to create subnodes in non-existing nodes or aliases
- Verify created nodes using fdt list command
The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Thu, 2 Mar 2023 03:08:36 +0000 (04:08 +0100)]
test: cmd: fdt: Test fdt set
Add 'fdt set' test which works as follows:
- Create fuller FDT, map it to sysmem
- Set either existing property to overwrite it, or new property
- Test setting both single properties as well as string and integer arrays
- Test setting to non-existent nodes and aliases
- Verify set values using 'fdt get value'
The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Thu, 2 Mar 2023 03:08:35 +0000 (04:08 +0100)]
test: cmd: fdt: Test fdt get size
Add 'fdt get size' test which works as follows:
- Create fuller FDT, map it to sysmem
- Get size of various properties
- Get node count of available nodes
- Test non-existent nodes and properties
The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Thu, 2 Mar 2023 03:08:34 +0000 (04:08 +0100)]
test: cmd: fdt: Test fdt get addr
Add 'fdt get addr' test which works as follows:
- Create fuller FDT, map it to sysmem
- Get address of various properties
- Compare addresses calculated by UT and fdt command
This test is special in that it has to go through gruesome remapping scheme
where the test calculates:
- pointer offsets of the generated FDT root and the property being tested
- map_sysmem() result of environment variable "fdtaddr" and the one set
by the test matching address of property being tested
- difference between the later and the former, to obtain offset of the
DT property from start of DT
The offsets must match in both the UT and the tested U-Boot, if they do
not, the test fails.
The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Thu, 2 Mar 2023 03:08:33 +0000 (04:08 +0100)]
test: cmd: fdt: Test fdt get name
Add 'fdt get name' test which works as follows:
- Create fuller FDT, map it to sysmem
- Get name of / node 0, 1 and /clk-test node 0
- Compare output and validate the node name
- Get name of / node 2 and /clk-test node 1
- Compare output and validate the node is not present
- Get name of / node -1 and /clk-test node -1
- Compare output and validate the node name equals node 0 name
- Check nonexistent node, verify the command errors out
The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Thu, 2 Mar 2023 03:08:31 +0000 (04:08 +0100)]
test: cmd: fdt: Test fdt resize
Add 'fdt resize' test which works as follows:
- Create simple FDT with extra size 0, map it to sysmem
- 'resize' the FDT by 0x2000 bytes
- Verify the new space has been added to the FDT
The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Thu, 2 Mar 2023 03:08:30 +0000 (04:08 +0100)]
test: cmd: fdt: Test fdt move
Add 'fdt move' test which works as follows:
- Create simple FDT, map it to sysmem
- 'move' the FDT into new zeroed out sysmem location
- Verify newly active FDT is in the new location
- Compare both locations
The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Thu, 2 Mar 2023 03:08:29 +0000 (04:08 +0100)]
test: cmd: fdt: Test both string and integer arrays in 'fdt get value'
The 'fdt get value' subcommand now supports extraction of integer value
from integer arrays, add test for it, including a test for special case
unindexed integer array read, which is handled as hash and treated as a
long string instead of integer.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Thu, 2 Mar 2023 03:08:27 +0000 (04:08 +0100)]
test: cmd: fdt: Generate fuller DT internally and switch fdt get value to it
Implement function to generate internal test DT fragment and switch
the 'fdt get value' test to this instead of depending on the sandbox
DT. Rename clk-test node to test-node node. This FDT fragment will be
reused by other tests. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Thu, 2 Mar 2023 03:08:26 +0000 (04:08 +0100)]
test: cmd: fdt: Rename fdt_test_get() to fdt_test_get_value()
The 'fdt get' command has a 'get value' subcommand, rename the fdt_test_get()
to fdt_test_get_value() to avoid confusion about what it is testing. There is
currently no get 'get name', 'get addr', 'get size' subcommand test.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Thu, 2 Mar 2023 03:08:25 +0000 (04:08 +0100)]
test: cmd: fdt: Rename fdt_test_resize() to fdt_test_addr_resize()
The 'fdt' command has a 'resize' subcommand, rename the fdt_test_resize()
to fdt_test_addr_resize() to avoid confusion about what it is testing.
There is currently no resize test.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Thu, 2 Mar 2023 03:08:23 +0000 (04:08 +0100)]
cmd: fdt: Add support for integer arrays in fdt get value with index
Currently any integer array value is set as long up-to-40 character
hexadecimal string into environment variable when extracted from an
FDT using 'fdt get value path prop index', because the support for
handling integer arrays is not implemented, and fdt_value_env_set()
code falls back into the hash handling behavior instead.
Implement this support simply by checking whether user supplied any
index. If index is set and the property length is multiple of four,
then this is an integer array, and the code would extract value at
specified index.
There is a subtle change where default index is set to -1 instead of 0.
This is OK, since the only place which checks for index to be less or
equal zero is the string array handling code in fdt_value_env_set() and
that code would work perfectly well with index -1 too.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Thu, 2 Mar 2023 03:08:22 +0000 (04:08 +0100)]
cmd: fdt: Map address returned from fdt get addr to sysmem
The address returned from 'fdt get addr' command must be mapped
into sysmem, as this is a working FDT. Access to this address
without mapping it would lead to crash e.g. in sandbox.
The following command triggers the crash:
"
./u-boot -Dc 'fdt addr $fdtcontroladdr ; fdt get addr var / compatible ; md $var'
"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Thu, 2 Mar 2023 03:08:21 +0000 (04:08 +0100)]
cmd: fdt: Handle 64bit pointers in fdt get addr
The command assumed 32bit pointers so far, with 64bit pointer the
command would overwrite a piece of stack. Fix it by extending the
array size to cater for 64bit pointer, and use snprintf() to avoid
writing past the end of the array ever again.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Thu, 2 Mar 2023 03:08:20 +0000 (04:08 +0100)]
cmd: fdt: Align checksign parameter names in help text
The help text references 'addr' as an optional key start address,
but the explanation references the same as 'start', make sure they
both read as 'addr'. Also update the abbreviated 'addr' in the
explanation to 'address'.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Thu, 2 Mar 2023 03:08:19 +0000 (04:08 +0100)]
cmd: fdt: Check argc before accessing argv in fdt memory
On case 'fdt memory' is invoked without parameters, argv[2]/argv[3]
is not valid and this command would SEGFAULT in sandbox environment.
Add missing argc test to avoid the crash and rather print usage help
message.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Thu, 2 Mar 2023 03:08:18 +0000 (04:08 +0100)]
cmd: fdt: Check argc before accessing argv in fdt bootcpu
On case 'fdt bootcpu' is invoked without parameters, argv[2] is not
valid and this command would SEGFAULT in sandbox environment. Add
missing argc test to avoid the crash and rather print usage help
message.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Thu, 2 Mar 2023 03:08:17 +0000 (04:08 +0100)]
cmd: fdt: Fix fdt rsvmem behavior on non-existent index and error message space
In case 'fdt rsvmem delete index' is passed a non-existent index, one
which does not exist in 'fdt rsvmem print', then the following command
triggers a print of help message for 'fdt' command instead of erroring
out:
=> fdt rsvmem delete 1234
This is because the subcommand errornously returns 'err' instead of
CMD_RET_FAILURE, fix it. Furthermore, align the number of spaces past
fdt_del_mem_rsv() and fdt_add_mem_rsv() in error message with the rest
of the code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Thu, 2 Mar 2023 03:08:16 +0000 (04:08 +0100)]
cmd: fdt: Fix fdt rm behavior on non-existent property and error message space
In case an FDT contains a node '/test-node@1234' , with no property
called 'noprop' in that node, the following command triggers a print
of help message for 'fdt' command instead of erroring out:
=> fdt rm /test-node@1234 noprop
This is because the subcommand errornously returns 'err' instead of
CMD_RET_FAILURE, fix it. Furthermore, align the number of spaces past
fdt_delprop() in error message with the rest of the code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Thu, 2 Mar 2023 03:08:15 +0000 (04:08 +0100)]
cmd: fdt: Fix handling of empty properties for fdt get addr and fdt get size
It is perfectly valid to request an address or size of FDT property
without value, the only special case if requesting of the value of
FDT property without value. Invert the test such, that properties
without value still set the variable from 'fdt get addr/size' to
address of the property or size of the property, where the later
is 0.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Thu, 2 Mar 2023 03:08:14 +0000 (04:08 +0100)]
cmd: fdt: Import is_printable_string() from DTC to fix u32 misprint
Import is_printable_string() implementation from DTC 1.7.0 as of
DTC commit 039a994 ("Bump version to v1.7.0") . This fixes a print
of u32 property which so far used to be printed as string by U-Boot
fdt print command.
We might see the case where the parsed property value, in this case
it is a 32-bit integer, identified as a printable string or a null byte
(concatenated strings) because of its last character happens to be:
0x00 (null character), 0xB (vertical tab character) or
0x10 (line feed character)
In this situation, if the string is identified as printable string,
it will be displayed as character instead of hex value
When the isprint() condition is true, there are two possibilities:
1) The character is ASCII character (except the first 32)
2) The character is extended ASCII character
For example,
NG property in device tree:
clock-frequency = <16640000>;
by default, would be displayed as
clock-frequency = "", "ýè";
and with this patch applied, would be displayed as
clock-frequency = <0x00fde800>;
Full investigation was done by Nam and Hai, patch reworked by Marek
to use common code from DTC.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Nam Nguyen <nam.nguyen.yh@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Thu, 9 Mar 2023 16:22:50 +0000 (11:22 -0500)]
Merge tag 'dm-next-9mar23' of https://source.denx.de/u-boot/custodians/u-boot-dm into next
binman x509, separate tools dir and other improvements
patman parallel patch generation
fdt fixes and tests
PyPi support for U-Boot tools
buildman reproducible builds
projects / u-boot.git / log
