Inspection showed that gd->malloc_limit is zero. And it is because
generally SPL_FRAMEWORK initialize SPL's gd->malloc_limit. But when
SPL_FRAMEWORK is not enabled then in most cases nobody initialize
gd->malloc_limit and so SPL malloc simple does not work.
So disable SPL_SYS_MALLOC_SIMPLE by default when SPL_FRAMEWORK is not
enabled. SPL_SYS_MALLOC_SIMPLE can be disabled only by setting
SPL_SYS_MALLOC_F_LEN to zero. So do it.
This change fixes SPL error "alloc space exhausted" on P2020 board.
Tom Rini [Thu, 21 Apr 2022 14:56:58 +0000 (10:56 -0400)]
Merge branch '2022-04-21-assorted-improvements'
- For the environment, add a arch_env_get_location hook and make use of
it on some NXP platforms (so that boards can override SoCs).
- Remove some unused squashfs code from SPL
- Resync am335x beaglebone related DTS files
- Enable SPL_SEPARATE_BSS if SPL_BSS_START_ADDR is used
Sean Anderson [Tue, 12 Apr 2022 14:59:04 +0000 (10:59 -0400)]
treewide: Enable SPL_SEPARATE_BSS if SPL_BSS_START_ADDR is used
If .bss does not immediately follow the end of the image, then
CONFIG_SPL_SEPARATE_BSS must be selected. Typically, the location of bss
is specified by using CONFIG_SPL_BSS_START_ADDR in a linker script. On
these arches, CONFIG_SPL_SEPARATE_BSS should be enabled. If there is an
option to use an alternate boot script (e.g. CONFIG_SPL_LDSCRIPT is just
a default), just imply. If there is not, select.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Paul Barker [Mon, 11 Apr 2022 15:42:01 +0000 (15:42 +0000)]
board: ti: am335x: Add support for BBE Extended WiFi
The Sancloud BeagleBone Enhanced Extended WiFi (BBE Extended WiFi) has
its own devicetree file and the board can be identified by the 2nd
letter of the config string within the common EEPROM.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Paul Barker [Mon, 11 Apr 2022 15:42:00 +0000 (15:42 +0000)]
board: ti: am335x: Add BBE Lite support
The Sancloud BeagleBone Enhanced Lite (BBE Lite) has its own devicetree
file and the board can be identified by the 2nd letter of the config
string within the common EEPROM.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Paul Barker [Mon, 11 Apr 2022 15:41:59 +0000 (15:41 +0000)]
arm: dts: Resync dts for BeagleBone and derivatives
Sync BeagleBone dts files & TPS dtsi files with Linux v5.17 and include
the SanCloud BBE Extended WiFi dts added in v5.18-rc1. Also pull in
changes to am33xx-l4.dtsi needed to support the BeagleBone Blue.
The change to use the cpsw switch driver (commit c477358e66a3 in Linux)
is excluded from the sync as u-boot does not recognise the new
compatible string.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Marek Vasut [Wed, 6 Apr 2022 00:21:34 +0000 (02:21 +0200)]
ARM: imx: imx8m: env: Switch to arch_env_get_location()
Implement arch_env_get_location() instead of env_get_location(), so that
the env_get_location() can be implemented on board level and override the
arch_env_get_location() architecture defaults.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Adam Ford <aford173@gmail.com> Cc: Fabio Estevam <festevam@denx.de> Cc: Marek Behún <marek.behun@nic.cz> Cc: Peng Fan <peng.fan@nxp.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefano Babic <sbabic@denx.de> Cc: Tim Harvey <tharvey@gateworks.com> Cc: Tom Rini <trini@konsulko.com> Cc: Tommaso Merciai <tomm.merciai@gmail.com> Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Marek Vasut [Wed, 6 Apr 2022 00:21:33 +0000 (02:21 +0200)]
armv8: layerscape: env: Switch to arch_env_get_location()
Implement arch_env_get_location() instead of env_get_location(), so that
the env_get_location() can be implemented on board level and override the
arch_env_get_location() architecture defaults.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Adam Ford <aford173@gmail.com> Cc: Fabio Estevam <festevam@denx.de> Cc: Marek Behún <marek.behun@nic.cz> Cc: Peng Fan <peng.fan@nxp.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefano Babic <sbabic@denx.de> Cc: Tim Harvey <tharvey@gateworks.com> Cc: Tom Rini <trini@konsulko.com> Cc: Tommaso Merciai <tomm.merciai@gmail.com> Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Currently there is only one way to override desired environment location,
by implementing env_get_location(). This is increasingly being conflated
both on board level and architecture level, which leads to a problem on
boards where this function is already implemented on architecture level,
since those boards have no way to override this environment location on
board level anymore.
Implement arch_env_get_location() function which is architecture specific
and should only ever be implemented in architecture code. This function
has lower priority than env_get_location(), which should only ever be
implemented in board code, and which overrides the arch_env_get_location()
architecture environment selection.
This way, architecture can define its default environment chooser, while
board can now override it as needed at all times.
There is no functional change, since env_get_location() simply returns
arch_env_get_location(), and arch_env_get_location() implements the
current env_get_location() default content.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Adam Ford <aford173@gmail.com> Cc: Fabio Estevam <festevam@denx.de> Cc: Marek Behún <marek.behun@nic.cz> Cc: Peng Fan <peng.fan@nxp.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefano Babic <sbabic@denx.de> Cc: Tim Harvey <tharvey@gateworks.com> Cc: Tom Rini <trini@konsulko.com> Cc: Tommaso Merciai <tomm.merciai@gmail.com> Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Tony Dinh [Sun, 17 Apr 2022 23:42:32 +0000 (16:42 -0700)]
arm: kirkwood: Sheevaplug : Use Marvell uclass mvgbe and PHY driver for Ethernet
The Globalscale Technologies Sheevaplug board has the network chip
Marvell 88E1116R. Use uclass mvgbe and the compatible driver M88E1310
driver to bring up Ethernet.
- Remove CONFIG_RESET_PHY_R symbol from all board files
- Use uclass mvgbe to bring up the network. And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Miscellaneous changes: Move constants to .c file and remove header file
board/Marvell/sheevaplug/sheevaplug.h, use BIT macro, and add/cleanup
comments.
board: turris: Allow to specify first eth idx of first MAC address
Turris Omnia uses first MAC address from OTP for second ethernet interface.
Second MAC address for third interface and third MAC address for first
interface.
Other Turris routers do not have this rotate by one mapping. So add
function parameter for specifying id of the first ethernet interface.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz>
board: turris: Move Turris Atsha OTP code to separate file
OTP code is not Atsha generic but also it is not Omnia specific. It is
common for all Turris routers which use Atsha cryptochip for storing OTP.
So move this common Turris specific Atsha OTP code from Turris Omnia into
separate file. It will be used also by other Turris routers.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz>
arm: mvebu: Enable CONFIG_SPL_SYS_NO_VECTOR_TABLE for 32-bit mvebu
U-Boot SPL is on 32-bit mvebu executed by the BootROM. And BootROM expects
that U-Boot SPL returns execution back to the BootROM. Vectors during
execution of U-Boot SPL should not be changed as BootROM does not expect it
and uses its own vectors. So do not overwrite vectors in SPL build.
tools: kwboot: Replace fstat()+st_size by lseek()+SEEK_END
fstat()'s st_size works only for regular files. lseek() with SEEK_END works
also for block or MTD devices. This replacement allows kwboot to load
kwbimage from /dev/mtd0 for booting another device over /dev/ttyS0.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz>
arm: mvebu: Add support for reading LD0 and LD1 eFuse
Armada 385 contains 64 lines of HD eFuse and 2 lines of LD eFuse. HD eFuse
is used for secure boot and each line is 64 bits long + 1 lock bit. LD
eFuse lines are 256 bits long + 1 lock bit. LD 0 line is reserved for
Marvell Internal Use and LD 1 line is for General Purpose Data. U-Boot
already contains HD eFuse reading and programming support.
This patch implements LD eFuse reading support. LD 0 line is mapped to
U-Boot fuse bank 64 and LD 1 line to fuse bank 65.
LD 0 Marvell Internal Use line seems that was burned in factory with some
data and can be read by U-Boot fuse command:
=> fuse read 64 0 9
LD 1 General Purpose Data line is by default empty and can be read by
U-Boot fuse command:
=> fuse read 65 0 9
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz>
Robert Marko [Thu, 24 Mar 2022 09:57:39 +0000 (10:57 +0100)]
mvebu: uDPU: update defconfig
Update the current uDPU defconfig with following changes:
* Disable CONFIG_SPI_BOOT, its not needed for booting and the device boots
from eMMC anyway.
* Disable CONFIG_SYS_CONSOLE_INFO_QUIET, there is no need to diverge from
other boards by not priting the console device
* Enable CONFIG_CMD_MTD in order to allow use of the MTD tool
* Disable CONFIG_CMD_MTDPARTS, with MTD now being able to parse partitions
from DTS there is no need for it, the default MTDPARTS were incorrect
anyway
* Enable CONFIG_MMC_HS200_SUPPORT, the eMMC used support both HS200 and
HS400 modes, so enable at least HS200 because Xenon driver does not
support HS400 currently
* Replace CONFIG_SPI_FLASH_BAR with CONFIG_SPI_FLASH_SFDP_SUPPORT
Utilize SFDP parsing instead of relying on the extended address registers
Signed-off-by: Robert Marko <robert.marko@sartura.hr> Reviewed-by: Stefan Roese <sr@denx.de>
Robert Marko [Thu, 24 Mar 2022 09:57:38 +0000 (10:57 +0100)]
arm: mvebu: dts: uDPU: fix non-working networking
uDPU is a bit of a specific device in that it does not have any copper
ports nor any ethernet PHY-s but 2 SFP ports.
This is an issue since MVNETA requires a PHY phandle or a fixed-link to
be defined under its node.
Since U-boot has no SFP support this is reasonable in order to know how
to configure the MAC.
However this also means that networking does not work on uDPU at all
currently, and fails with:
uDPU>> dhcp
Could not get PHY for neta@30000: addr 0
phy_connect failed
Could not get PHY for neta@40000: addr 1
phy_connect failed
So, to provide working networking using only SFP-s let add the fixed-link
at 1G which is much more common than 2.5G SFP-s as well as disable the
TX_DISABLE pins like done on Armada 7040 and 8040 platforms.
Since uDPU is not using any of the GPIO-s on the SB controller for any
purpose other than GPIO, a call to the pinctrl must be made in order for
it to get probed and thus register the SB GPIO bank, otherwise SB GPIO-s
are not registered at all.
Signed-off-by: Robert Marko <robert.marko@sartura.hr> Reviewed-by: Stefan Roese <sr@denx.de>
Robert Marko [Thu, 24 Mar 2022 09:57:37 +0000 (10:57 +0100)]
net: mvneta: add SFP TX disable handling
Add support for handling SFP TX disable for MVNETA in the same fashion as
to what MVPP2 is doing in order to enable using SFP-s.
This allows using ethernet on SFP only boards.
Signed-off-by: Robert Marko <robert.marko@sartura.hr> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Wed, 23 Feb 2022 13:15:49 +0000 (14:15 +0100)]
arm: mvebu: a37xx: Add support for reading Security OTP values
It is not possible for the A53 core (on which U-Boot is running) to read it
directly. For this purpose Marvell defined mbox API for sending OTP
commands between CM3 and A53 cores.
Implement these Marvell fuse reading mbox commands via U-Boot fuse API.
Banks 0-43 are used for accessing Security OTP (44 rows with 67 bits via 44
banks and words 0-2).
Note that of the 67 bits, the 3 upper bits are: 1 lock bit and 2
auxiliary bits (meant for testing during the manufacture of the SOC, as
I understand it).
Also note that the lock bit and the auxiliary bits are not readable
via Marvell commands.
With CZ.NIC's commands the lock bit is readable.
Write support is not implemented yet.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Wed, 23 Feb 2022 13:15:48 +0000 (14:15 +0100)]
arm: mvebu: a37xx: Extend mbox_do_cmd() code
Allow to specify input parameters, define all available mbox commands
supported by CZ.NIC's secure firmware and also Marvell's fuse.bin firmware
and fix parsing response from Marvell OTP commands.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Wed, 23 Feb 2022 13:15:47 +0000 (14:15 +0100)]
arm: mvebu: a37xx: Move generic mbox code to arch/arm/mach-mvebu
Generic A3720 mbox code is currently in Turris Mox specific board file
board/CZ.NIC/turris_mox/mox_sp.c. Move it to board independent arch file
arch/arm/mach-mvebu/armada3700/mbox.c.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Wed, 23 Feb 2022 13:15:45 +0000 (14:15 +0100)]
arm: mvebu: a37xx: Add support for reading NB and SB fuse OTP value
Implement reading NB and SB fuses of Armada 37xx SOC via U-Boot fuse API.
Banks 0-43 are reserved for accessing Security OTP (not implemented yet).
Bank 44 is used for accessing North Bridge OTP (69 bits via words 0-2).
Bank 45 is used for accessing South Bridge OTP (97 bits via words 0-3).
Write support is not implemented yet because it looks like that both North
and South Bridge OTPs are already burned in factory with some data. The
meaning of some bits of North Bridge is documented in WTMI source code.
The meaning of bits in South Bridge is unknown.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
Rogier Stam [Tue, 8 Feb 2022 23:27:00 +0000 (00:27 +0100)]
arm: mvebu: Fix Espressobin build for configs where ENV is not in SPI
When storing the UBoot Environment in for example EXT4,
the U-Boot build is broken for several reasons:
1. armada-385-turris-omnia-u-boot.dtsi will not allow
CONFIG_ENV_OFFSET and CONFIG_ENV_SIZE to be undefined
2. armada-37xx/board.c ft_board_setup function does not
exist if CONFIG_ENV_IS_IN_SPI_FLASH is not defined
This commit changes these files so that selecting a
different location for the environment is possible.
Pali Rohár [Thu, 3 Feb 2022 16:50:46 +0000 (17:50 +0100)]
tools/mrvl_uart.sh: Remove script
There are two tools for sending images over UART to Marvell SoCs: kwboot
and mrvl_uart.sh. kwboot received lot of new features and improvements in
last few months. There is no need to maintain two tools in U-Boot, so
remove old mrvl_uart.sh tool.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Marcel Ziswiler <marcel@ziswiler.com> Tested-by: Marcel Ziswiler <marcel@ziswiler.com> Reviewed-by: Tony Dinh <mibodhi@gmail.com>
Tom Rini [Wed, 20 Apr 2022 18:33:53 +0000 (14:33 -0400)]
Merge branch '2022-04-20-assorted-improvements'
- Two TI K3 updates, update SYS_MALLOC_F_LEN default to be 0x2000 and
move TI am33xx to use that as well, fix DT relocation with multiple
DRAM banks, and add a gpio read sub-command.
Diego Rondini [Mon, 11 Apr 2022 10:02:09 +0000 (12:02 +0200)]
cmd: gpio: Add `gpio read` subcommand
As explained in commit 4af2a33ee5b9 ("cmd: gpio: Make `gpio input`
return pin value again") the `gpio input` is used in scripts to obtain
the value of a pin, despite the fact that CMD_RET_FAILURE is
indistinguishable from a valid pin value.
To be able to detect failures and properly use the value of a GPIO in
scripts we introduce the `gpio read` command that sets the variable
`name` to the value of the pin. Return code of the `gpio read` command
can be used to check for CMD_RET_SUCCESS or CMD_RET_FAILURE.
CONFIG_CMD_GPIO_READ is used to enable the `gpio read` command.
Signed-off-by: Diego Rondini <diego.rondini@kynetics.com>
Dave Gerlach [Fri, 8 Apr 2022 21:46:50 +0000 (16:46 -0500)]
ram: k3-ddrss: Allow use of dt provided initial frequency
Allow device tree to provide ti,ddr-freq0 to be used as the initial DDR
frequency that is set for lpddr4 before initialization of the
controller. Make this optional and continue to use PLL bypass frequency
as is done currently if ti,ddr-freq0 is not provided.
Marek Vasut [Fri, 8 Apr 2022 00:09:19 +0000 (02:09 +0200)]
image: fdt: Fix DT relocation handling with multiple DRAM banks with gap
The current implementation of boot_relocate_fdt() places DT at the
highest usable DRAM address, which is calculated as:
env_get_bootm_low() + env_get_bootm_mapsize()
which by default becomes gd->ram_base + gd->ram_size.
Systems like i.MX53 can have multiple DRAM banks with gap between them,
e.g. have DRAM at 0x70000000-0x8fffffff and 0xb0000000-0xcfffffff , so
for them the calculated highest DRAM address is 0xafffffff, which is
exactly in the gap and thus not usable.
Fix this by iterating over all DRAM banks and tracking the remaining
amount of the total mapping size obtained from env_get_bootm_mapsize().
Limit the maximum LMB area size to each bank, to avoid using nonexistent
DRAM.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Heinrich Schuchardt <xypron.glpk@gmx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@konsulko.com>
ram: k3-ddrss: Fix register name and explain its usage
The k3-ddrss driver wants to configure the DDRSS_V2A_CTL_REG to reflect
the maximum possible SDRAM of 2 GB for AM64x (instead of the register's
default that says 8 GB, which the AM64x DDR controller wouldn't support).
The offset 0x20 was correct, but the register name DDRSS_V2A_R1_MAT_REG
was that of the next register at offset 0x24.
Tom Rini [Tue, 19 Apr 2022 21:02:21 +0000 (17:02 -0400)]
Merge branch '2022-04-19-assorted-updates'
- Migrate CONFIG_SYS_MEM_TOP_HIDE to Kconfig, IOMUX bugfix, 2 BTRFS
bugfixes, update .gitignore and .mailmap files, aspeed GPIO bugfix,
image-fit and squashfs code cleanups, enable EXT4 and ISO partitions on
DeveloperBox.
- populate u-boot,bootconf under /chosen, see
https://github.com/devicetree-org/dt-schema/pull/71 for corresponding
change
Currently there is no btrfs support in SPL. But macro CONFIG_FS_BTRFS is
defined also when building SPL. When both FS_BTRFS and SPL are enabled
then build process throw compile error.
Fix check for btrfs code in fstypes[] to allow compiling FS_BTRFS only in
proper U-Boot.
Fix following two compile errors on big endian systems:
CC fs/btrfs/btrfs.o
In file included from include/linux/byteorder/big_endian.h:107,
from ./arch/powerpc/include/asm/byteorder.h:82,
from ./arch/powerpc/include/asm/bitops.h:8,
from include/linux/bitops.h:152,
from include/uuid.h:9,
from fs/btrfs/btrfs.c:10:
fs/btrfs/conv-funcs.h: In function ‘btrfs_key_to_disk’:
include/linux/byteorder/generic.h:90:21: error: ‘__cpu_to_le16’ undeclared (first use in this function); did you mean ‘__cpu_to_le16p’?
#define cpu_to_le16 __cpu_to_le16
^~~~~~~~~~~~~
fs/btrfs/conv-funcs.h:79:10: note: in expansion of macro ‘cpu_to_le16’
__u16: cpu_to_le16, \
^~~~~~~~~~~
CC fs/btrfs/compression.o
In file included from ./arch/powerpc/include/asm/unaligned.h:9,
from fs/btrfs/compression.c:16:
include/linux/unaligned/access_ok.h:6:19: error: redefinition of ‘get_unaligned_le16’
static inline u16 get_unaligned_le16(const void *p)
^~~~~~~~~~~~~~~~~~
In file included from fs/btrfs/ctree.h:16,
from fs/btrfs/btrfs.h:12,
from fs/btrfs/compression.c:8:
include/linux/unaligned/le_byteshift.h:40:19: note: previous definition of ‘get_unaligned_le16’ was here
static inline u16 get_unaligned_le16(const void *p)
^~~~~~~~~~~~~~~~~~
Include file asm/unaligned.h contains arch specific macros and functions
for unaligned access as opposite to linux/unaligned le_byteshift.h which
contains macros and functions specific to little endian systems only.
Sean Anderson [Wed, 6 Apr 2022 18:36:35 +0000 (14:36 -0400)]
IOMUX: Fix access past end of console_devices
We should only access console_devices[file][i] once we have checked that i
< cd_count[file]. Otherwise, we will access uninitialized memory at the end
of the loop. console_devices[file][i] should not be NULL, but putting the
assignment in the loop condition allows us to ensure that i is checked
beforehand. This isn't a bug, but it does make valgrind stop complaining.
Fixes: 400797cad3 ("IOMUX: Split out for_each_console_dev() helper macro") Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Andrew Scull <ascull@google.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Billy Tsai [Wed, 13 Apr 2022 05:34:51 +0000 (13:34 +0800)]
gpio: aspeed: Fix incorrect offset of read back register.
The offset of the current read back register is the value of the gpio pin,
not the value written for the gpio output.
This patch fix it to avoid the other gpio output value controlled by the
same register being set incorrectly.
configs: Enable EXT4 and ISO partitions for the DeveloperBox
Since this box is SystemReady compliant enable ISO_PARTITION which is
needed to start some installers (e.g Fedora). While at it enable EXT4
as well which is a common filesystem for targets
Michal Simek [Thu, 14 Apr 2022 13:50:46 +0000 (15:50 +0200)]
.mailmap: Start to use new amd.com email address
Xilinx has been acquired by AMD that's why emails should be also updated.
The patch is updating .mailmap file and also MAINTAINERS files as was done
by commit 5cd1ecb99490 ("ppc: qemu: Update MAINTAINERS for correct email
address").
The rest of my emails are not going to change.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Michal Simek <michal.simek@amd.com>
Daniel Golle [Tue, 12 Apr 2022 20:00:43 +0000 (21:00 +0100)]
image-fdt: save name of FIT configuration in '/chosen' node
It can be useful for the OS (Linux) to know which configuration has
been chosen by U-Boot when launching a FIT image.
Store the name of the FIT configuration node used in a new string
property called 'u-boot,bootconf' in the '/chosen' node in device tree.
Signed-off-by: Daniel Golle <daniel@makrotopia.org> Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Sun, 27 Mar 2022 20:26:20 +0000 (14:26 -0600)]
dm: core: Deal with a wrinkle with linker lists
When every member of a linker list is aligned by the compiler, we can no
longer rely on the sizeof of the struct to determine the number of
entries.
For example, if the struct size is 0x90 but every entry is aligned to 0xa0
by the compiler, the linker list entries takes more space in memory and
the calculation of the number of entries is incorrect. For example, we may
see 0x12 entries when there are only 0x11.
This is a real problem. There may be a general solution, although I cannot
currently think of one. So far it only bites with OF_PLATDATA_RT which
creates a pointer to each entry of the 'struct udevice' linker_list. This
does not happen without that option, so it only affects SPL.
Work around it by manually calculating the aligned size of struct udevice,
then using that for the n_ent calculation.
Simon Glass [Sun, 27 Mar 2022 20:26:18 +0000 (14:26 -0600)]
sandbox: Align linker lists to a 32-byte boundary
Use this larger boundary to ensure that linker lists at least start on the
maximum possible alignment boundary. See also the CONFIG_LINKER_LIST_ALIGN
setting, but that is host-arch-specific, so it seems better to use the
largest value for every host architecture.
Simon Glass [Sun, 27 Mar 2022 20:26:14 +0000 (14:26 -0600)]
sandbox: Correct loss of early output in SPL
At present fputc() is used before the console is available, then write()
is used. These are not compatible. Since fputc() buffers internally it is
better to use the write(), so that a partial line is immediately
displayed.
This has a slight effect on performance, but we are already using write()
for the vast majority of the output with no obvious impacts.
Johan Jonker [Sat, 16 Apr 2022 08:25:16 +0000 (10:25 +0200)]
rockchip: video: mipi: add more compatible strings for rk3288/rk3399
The rk3288/RK3399 DT synced from Linux contains some different
compatible strings in the mipi node then origanal used in U-boot.
Allow both options to be backwards compatible and to be able
to handle recent rk3288.dtsi and rk3399.dtsi files.
Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Johan Jonker [Sat, 16 Apr 2022 07:45:56 +0000 (09:45 +0200)]
rockchip: video: rk_edp: add more rk3288 edp node options
The rk3288 DT synced from Linux contains some different
properties in the edp node then origanal used in U-boot.
Allow both options to be backwards compatible and to be able
to handle recent rk3288.dtsi files.
Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Johan Jonker [Fri, 15 Apr 2022 21:21:43 +0000 (23:21 +0200)]
rockchip: fix boot_devices constants
The DT node name pattern in mmc-controller.yaml for mmc
is "^mmc(@.*)?$". The Rockchip mmc nodes have been synced
with Linux, so update the boot_devices constants as well.
Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Johan Jonker [Fri, 15 Apr 2022 21:21:38 +0000 (23:21 +0200)]
rockchip: rk3288-cru: sync the clock dt-binding header from Linux
In order to update the DT for rk3288
sync the clock dt-binding header.
This is the state as of v5.17 in Linux.
Keep SCLK_MAC_PLL in use for rk3288 clock driver.
Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Johan Jonker [Fri, 15 Apr 2022 21:21:37 +0000 (23:21 +0200)]
rockchip: rk3288-power: sync power domain dt-binding header from Linux
In order to update the DT for rk3288
sync the power domain dt-binding header.
This is the state as of v5.17 in Linux.
Change location to be more in line with other SoCs.
Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Johan Jonker [Sat, 16 Apr 2022 15:09:52 +0000 (17:09 +0200)]
doc: rockchip: add rk3066 Rikomagic MK808
Add rk3066 Rikomagic MK808 to the list of
mainline supported Rockchip boards.
Include instructions for creating and programming
images to NAND and SD card.
Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Johan Jonker [Sat, 16 Apr 2022 15:09:45 +0000 (17:09 +0200)]
arm: dts: rockchip: add rk3066a-mk808.dts
MK808 is a RK3066-based board with 1 USB host and 1 USB OTG port,
HDMI and a micro-SD card slot. It also includes on-board NAND
and 1GB of SDRAM. Add rk3066a-mk808.dts. Move U-boot specific
things in a rk3066a-mk808-u-boot.dtsi file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Johan Jonker [Sat, 16 Apr 2022 15:09:42 +0000 (17:09 +0200)]
arm: dts: rockchip: fix rk3xxx-u-boot.dtsi
The file rk3xxx-u-boot.dtsi was original only for rk3188 and SPL.
With rk3066 added some nodes are also needed in TPL,
so change them to u-boot,dm-pre-reloc
Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Paweł Jarosz [Sat, 16 Apr 2022 15:09:41 +0000 (17:09 +0200)]
rockchip: rk3066: add sdram driver
Add rockchip rk3066 sdram driver
Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com> Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Paweł Jarosz [Sat, 16 Apr 2022 15:09:40 +0000 (17:09 +0200)]
rockchip: rk3066: add rk3066 pinctrl driver
Add driver supporting pin multiplexing on rk3066 platform.
Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com> Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Paweł Jarosz [Sat, 16 Apr 2022 15:09:39 +0000 (17:09 +0200)]
rockchip: rk3066: add clock driver for rk3066 soc
Add the clock driver for the rk3066 platform.
Derived from the rk3288 and rk3188 driver it
supports only a bare minimum to bring up the system
to reduce the TPL size for:
SDRAM clock configuration.
The boot devices NAND, EMMC, SDMMC, SPI.
A UART for the debug messages (fixed) at 115200n8.
A SARADC for the recovery button.
A TIMER for the delays (fixed).
There's support for two possible frequencies,
the safe 600MHz which will work with default pmic settings and
will be set to get away from the 24MHz default and
the maximum of 1.416Ghz, which boards can set if they
were able to get pmic support for it.
After the clock tree is set during the TPL probe
there's no parent update support.
In OF_REAL mode the drivers ns16550.c and dw-apb-timer.c
obtain the (fixed) clk_get_rate from the clock driver
instead of platdata.
The rk3066 cru node has a number of assigned-clocks properties
that call the .set_rate() function. Add them to the list so that
they return a 0 instead of -ENOENT.
Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com> Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Paweł Jarosz [Sat, 16 Apr 2022 15:09:38 +0000 (17:09 +0200)]
rockchip: rk3066: add grf header file
grf is needed by various drivers for rk3066 soc.
Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com> Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Johan Jonker [Sat, 9 Apr 2022 16:55:14 +0000 (18:55 +0200)]
rockchip: serial: Kconfig: allow ROCKCHIP_SERIAL enabled in TPL
The serial_rockchip.c driver converts platdata to the data structure
used in the ns16550.c file and then calls the function
ns16550_serial_probe().
When compiled with OF_REAL the serial_rockchip.c driver returns
now -ENODEV when probed and does no harm.
The config ROCKCHIP_SERIAL is currently depends on SPL_OF_PLATDATA.
Allow serial port use for both SPL and TPL by removing this
dependency and SPL_BUILD restriction.
Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Johan Jonker [Sat, 9 Apr 2022 16:55:12 +0000 (18:55 +0200)]
rockchip: serial: rename U_BOOT_DRIVER name to rockchip_uart
When a defconfig for rk3288 is compiled it gives the warning:
rockchip_rk3288_uart: Missing .compatible in
./drivers/serial/serial_rockchip.c
: WARNING: the driver rockchip_rk3288_uart
was not found in the driver list
Fix by renaming U_BOOT_DRIVER name of serial_rockchip.c
to rockchip_uart. Add rk3288 serial support with
a DM_DRIVER_ALIAS define.
Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Johan Jonker [Sat, 9 Apr 2022 16:55:11 +0000 (18:55 +0200)]
rockchip: serial: move driver alias to serial_rockchip.c
The Rockchip uart DT nodes have "snps,dw-apb-uart" as
fall back string. The driver ns16550.c has CONFIG_IS_ENABLED(OF_REAL)
as condition to of_match and does not copy dtplat data.
For TPL/SPL the driver serial_rockchip.c
is used. Move driver alias to correct driver.
Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Johan Jonker [Sat, 9 Apr 2022 16:55:10 +0000 (18:55 +0200)]
rockchip: serial: restyle the serial_rockchip.c driver
The ns16550.c driver has the following conditions for .of_match:
CONFIG_IS_ENABLED(OF_REAL)
For Rockchip SoCs with TPL/SPL and platform data that need serial
support the serial_rockchip.c driver was made. It copies this data
and then calls ns16550_serial_probe(). With the addition of yet an other
SoC type this driver is in need for a little restyle.
Simplify struct rockchip_uart_plat and add extra SoCs with
DM_DRIVER_ALIAS(). Return -ENODEV when the ns16550.c driver
probe function is available.
Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Johan Jonker [Sat, 9 Apr 2022 16:55:09 +0000 (18:55 +0200)]
rockchip: mmc: rockchip_dw_mmc: add rk3066/rk3188 support
The Rockchip SoCs rk3066/rk3188 have MMC DT nodes
with as compatible string "rockchip,rk2928-dw-mshc".
Add OF_PLATDATA support to the existing driver with
help of a DM_DRIVER_ALIAS.
This type needs a permanent enabled fifo.
The other Rockchip SoCs always have the property
"u-boot,spl-fifo-mode" in the MMC DT nodes,
because MMC to SRAM can't do DMA.
Make this property a requirement for MMC OF_PLATDATA
structures. The property "fifo-mode" must be added
for all other compile modes.
Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Johan Jonker [Sat, 9 Apr 2022 16:55:08 +0000 (18:55 +0200)]
rockchip: mmc: rockchip_dw_mmc: fix ciu clock index
The document rockchip-dw-mshc.yaml decribes a maximum of 4 clocks.
In the rockchip_dw_mmc driver the clock name in use was "fixed"
to "ciu" with index 1, but later reverted back to index 0.
The clock drivers can handle both, but the calling driver
should submit correct data as a standard practice.
Fix the "ciu" clock index by setting it back to 1.
projects / u-boot.git / log
