Tom Rini [Sun, 21 Feb 2021 16:17:30 +0000 (11:17 -0500)]
Merge tag 'efi-2021-04-rc3' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2021-04-rc3
Bug fixes:
* Let EFI simple file protocol access last block of partition
* Correct conversion of multi-part device paths in
EFI_DEVICE_PATH_TO_TEXT_PROTOCOL.ConvertDevicePathToText()
Our current implementation of
EFI_DEVICE_PATH_TO_TEXT_PROTOCOL.ConvertDevicePathToText() truncates multi
part device paths after the first part. We should convert all parts.
Render device path instance ends as commas. This is not explicitly
described in the UEFI spec but mimics what EDK II does.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Igor Opaniuk [Tue, 9 Feb 2021 11:52:45 +0000 (13:52 +0200)]
dm: i2c: use CONFIG_IS_ENABLED macro for DM_I2C/DM_I2C_GPIO
Use CONFIG_IS_ENABLED() macro, which provides more convenient
way to check $(SPL)DM_I2C/$(SPL)DM_I2C_GPIO configs
for both SPL and U-Boot proper.
CONFIG_IS_ENABLED(DM_I2C) expands to:
- 1 if CONFIG_SPL_BUILD is undefined and CONFIG_DM_I2C is set to 'y',
- 1 if CONFIG_SPL_BUILD is defined and CONFIG_SPL_DM_I2C is set to 'y',
- 0 otherwise.
All occurences were replaced automatically using these bash cmds:
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C/if !CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C/if CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C)/CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C_GPIO/if !CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C_GPIO/if CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C_GPIO)/CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
Reviewed-by: Heiko Schocher <hs@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Igor Opaniuk [Tue, 9 Feb 2021 11:52:44 +0000 (13:52 +0200)]
board: freescale: drop CONFIG_DM_I2C undefs
Drop CONFIG_DM_I2C undefs from board header files, and make them
disabled on these boards in defconfigs instead.
Disabling on Kconfig symbol was done automatically with this script:
cd configs
files=(*ls1046a*)
files2=(*T104*RDB*)
files3=(ls1021atwr_*)
files4=("imx8mp_evk_defconfig phycore-imx8mp_defconfig")
combine=("${files[@]}" "${files2[@]}" "${files3[@]}" "${files4[@]}")
cd ..
for item in ${combine[*]}
do
echo "Adjusting $item"
echo "# CONFIG_SPL_DM_I2C is not set" >> configs/$item
make $item && make savedefconfig && cp defconfig configs/$item
done
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io> Reviewed-by: Tom Rini <trini@konsulko.com>
Igor Opaniuk [Tue, 9 Feb 2021 11:52:43 +0000 (13:52 +0200)]
dm: i2c: allow disabling driver model in SPL
At present if U-Boot proper uses driver model for I2C, then SPL has to
also. While this is desirable, it places a significant barrier to moving
to driver model in some cases. For example, with a space-constrained SPL
it may be necessary to enable CONFIG_SPL_OF_PLATDATA which involves
adjusting some drivers.
This patch introduces a separate Kconfig symbols for enabling DM_I2C and
DM_I2C_GPIO support in SPL.
This will also help to get away from dirty workarounds to
achieve non-DM I2C support for SPL, which is currently used in some
board header files like:
ifdef CONFIG_SPL_BUILD
undef CONFIG_DM_I2C
endif
Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heiko Schocher <hs@denx.de> Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io> Reviewed-by: Tom Rini <trini@konsulko.com>
Eugen Hristev [Fri, 4 Dec 2020 16:06:55 +0000 (18:06 +0200)]
i2c: at91: fix crash when using 'i2c probe'
When issuing 'i2c probe', the driver was crashing, because at probe
there is a request with zero length buffer to write to i2c bus.
The xfer_msg function assumes the buffer is always there, and never
checks for the buffer length.
Harm Berntsen [Sun, 29 Nov 2020 09:47:15 +0000 (09:47 +0000)]
i2c: i2c-gpio: Fix GPIO output
The dm_gpio_set_dir_flags function cannot be used to update the
configuration of a GPIO pin because it does a bitwise OR with the
existing flags. Looks like commit 788ea834124b ("gpio: add function
_dm_gpio_set_dir_flags") has introduced this behaviour and the i2c-gpio
driver has been broken since.
Marek Vasut [Fri, 15 Jan 2021 23:27:50 +0000 (00:27 +0100)]
ARM: rmobile: Enable CONFIG_PCI_REGION_MULTI_ENTRY on RCar3
R-Car3 can have multiple regions of type memory in DT, enable
CONFIG_PCI_REGION_MULTI_ENTRY to handle those instead of using
just one of the memory regions.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Marek Vasut [Fri, 15 Jan 2021 23:33:17 +0000 (00:33 +0100)]
pci: renesas: Fix BAR mapping on Gen3
Because the first PCIExAR(n) register is configured with the mapping,
It is the second PCIExAR(n) register that must be written with 0, not
the last one. Update the n from 4 to 1 to select the correct register.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Andre Przywara [Sun, 14 Feb 2021 10:35:18 +0000 (10:35 +0000)]
fdt/sunxi: Remove OF_STDOUT_PATH
OF_STDOUT_PATH was meant to hold the devicetree path to the serial
console, to be put into the linux,stdout-path property of the chosen node.
The only user of that was sunxi, and it was actually wrong for years
there: the paths hardcoded in sunxi_common.h were not matching the DTs,
evident by the leading 0's in nodenames, which have been removed years
ago.
On top of that, "linux,stdout-path" is now deprecated for a while (Linux
commit 2a9d832cc9aae from November 2014), and also all modern DTs
(including those included in U-Boot) carry a "stdout-path" property
already.
So remove the stanza from sunxi_common.h, and, since this was the last
user, also remove the associated bits from the rest of U-Boot.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Tobias Schramm [Sun, 14 Feb 2021 23:19:58 +0000 (00:19 +0100)]
sunxi: support boot console on uart1 for sun8i
The A23, A33, H3, H5, A83T, V3 and Sochip S3 sun8i SoCs can mux uart1 on
GPIOs PG6 and PG7. This patch adds support for using uart1 on those pins
as boot console.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Mon, 8 Feb 2021 06:04:57 +0000 (00:04 -0600)]
sunxi: Remove dead ifdefs in sunxi-common.h
As variables were moved to Kconfig, some of the surrounding ifdefs were
left around, even though they were empty. Clean them up.
Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Jernej Skrabec [Mon, 1 Feb 2021 17:25:57 +0000 (18:25 +0100)]
sunxi: spl: Fix H616 clock initialization
It turns out that there is a magic bit in PRCM region which seemingly
makes PLLs work if it's enabled. Sadly, there is no documentation what
it does exactly, so we'll just mimick BSP boot0 behaviour and enable it
before any clock is set up.
Fixes: b18bd53d6cde ("sunxi: introduce support for H616 clocks") Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tom Rini [Fri, 19 Feb 2021 16:56:14 +0000 (11:56 -0500)]
Merge tag 'mmc-2021-2-19' of https://gitlab.denx.de/u-boot/custodians/u-boot-mmc
- mmc_spi improvement
- added mmc-pwrseq to remove duplicated code
- fix response timeout after switch command
- sdhci: skip cache invalidation if DMA is not used
Jaehoon Chung [Tue, 16 Feb 2021 01:16:55 +0000 (10:16 +0900)]
ARM: mach-meson: select MMC_PWRSEQ config
Before time, PWRSEQ is selected since below commit.
commit 262d34363373 ("board: amlogic: select PWRSEQ for all amlogic platform")
Select MMC_PWRSEQ config because of introducing CONFIG_MMC_PWRSEQ for
only eMMC module.
Bin Meng [Tue, 2 Feb 2021 02:48:48 +0000 (10:48 +0800)]
mmc: mmc_spi: Document the 3 local functions
mmc_spi_sendcmd(), mmc_spi_readdata() and mmc_spi_writedata() are
currently undocumented. Add comment blocks to explain the arguments
and the return value.
Signed-off-by: Bin Meng <bin.meng@windriver.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Bin Meng [Tue, 2 Feb 2021 02:48:47 +0000 (10:48 +0800)]
mmc: mmc_spi: Fix potential spec violation in receiving card response
After command is sent and before card response shows up on the line,
there is a variable number of clock cycles in between called Ncr.
The spec [1] says the minimum is 1 byte and the maximum is 8 bytes.
Current logic in mmc_spi_sendcmd() has a flaw that it could only work
with certain SD cards with their Ncr being just 1 byte.
When resp_match is false, the codes try to receive only 1 byte from
the SD card. On the other hand when resp_match is true, the logic
happens to be no problem as it loops until timeout to receive as many
bytes as possible to see a match of the expected resp_match_value.
However not every call to mmc_spi_sendcmd() is made with resp_match
being true hence this exposes a potential issue with SD cards that
have a larger Ncr value.
Given no issue was reported as of today, we can reasonably conclude
that all cards being used on the supported boards happen to have a 1
byte Ncr timing requirement. But a broken case can be triggered by
utilizing QEMU to emulate a larger value of Ncr (by default 1 byte
Ncr is used on QEMU). This commit fixes such potential spec violation
to improve the card compatibility.
Stefan Bosch [Sat, 23 Jan 2021 12:37:41 +0000 (13:37 +0100)]
mmc: fix response timeout after switch command
After issuing the switch command: Wait until 'current state' of the card
status becomes 'tran'. This prevents from response timeout at the next
command because of 'current state' = 'data'.
Signed-off-by: Stefan Bosch <stefan_b@posteo.net> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
mmc: sdhci: skip cache invalidation if DMA is not used
If DMA(SDMA or ADMA) is not used, the cache invalidation
after reading is no need, should be skipped. Otherwise
U-Boot may hang at the cache invalidation.
Found this issue and tested this fix on DragonBoard 410c.
Fixes: commit 4155ad9aac94 ("mmc: sdhci: fix missing cache invalidation after reading by DMA") Signed-off-by: Yuezhang.Mo <Yuezhang.Mo@sony.com> Reviewed-by: Andy Wu <Andy.Wu@sony.com>
The 'brcm,bcm2711-hdmi0' compatible string is used on RPi4 instead of
'brcm,bcm2835-hdmi' since the IP core was upgraded (now called VC6
instead of VC4). This has no functional change as far as u-boot driver
is concerned. So simply add the compatible string.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Tested-by: Peter Robinson <pbrobinson@gmail.com> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
xhci: translate virtual addresses into the bus's address space
So far we've been content with passing physical addresses when
configuring memory addresses into XHCI controllers, but not all
platforms have buses with transparent mappings. Specifically the
Raspberry Pi 4 might introduce an offset to memory accesses incoming
from its PCIe port.
Introduce xhci_virt_to_bus() and xhci_bus_to_virt() to cater with these
limitations, and make sure we don't break non DM users.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Peter Robinson <pbrobinson@gmail.com>
[mb: fix compilation for 32 bit] Signed-off-by: Matthias Brugger <mbrugger@suse.com>
fix from nicolas
These functions, instead of relying on hard-coded platform-specific
address translations, make use of the DMA constraints provided by the DM
core. This allows for per-device translations.
We can't yet get rid of the legacy phys_to_bus()/bus_to_phys()
implementations as some of its users are not integrated into the
device model.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Peter Robinson <pbrobinson@gmail.com> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
dm: Introduce DMA constraints into the core device model
Calculating the DMA offset between a bus address space and CPU's every
time we call phys_to_bus() and bus_to_phys() isn't ideal performance
wise, as it implies traversing the device tree from the device's node up
to the root. Since this information is static and available before the
device's initialization, parse it before the probe call an provide the
DMA offset in 'struct udevice' for the address translation code to use
it.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Peter Robinson <pbrobinson@gmail.com> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Add the following functions to get a specific device's DMA ranges:
- dev_get_dma_range()
- ofnode_get_dma_range()
- of_get_dma_range()
- fdt_get_dma_range()
They are specially useful in oder to be able validate a physical address
space range into a bus's and to convert addresses from and to address
spaces.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Peter Robinson <pbrobinson@gmail.com> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
So far we've assumed a fixed configuration for inbound windows as we had
a single user for this controller. But the controller's DMA constraints
were improved starting with BCM2711's B1 revision of the SoC, notably
available in CM4 and Pi400. They allow for wider inbound windows. We can
now cover the whole address space, whereas before we where limited to
the lower 3GB.
This information is passed to us through DT's 'dma-ranges' property and
it's specially important for us to honor it since some interactions with
the board's co-processor assume we're doing so (specifically the XHCI
firmware load operation, which is handled by the co-processor after
u-boot has correctly configured the PCIe controller).
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Tested-by: Peter Robinson <pbrobinson@gmail.com> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
The Raspberry Pi Foundation released the new Compute Module 4 which we
want to detect, so we can enable Ethernet on it and know the correct
device tree file name.
Note that this sets the Ethernet option to true since the official CM4
IO board has an Ethernet port. But that might not be the case when using
custom ones.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Reviewed-by: Peter Robinson <pbrobinson@gmail.com> Tested-by: Peter Robinson <pbrobinson@gmail.com> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
The Raspberry Pi Foundation released the new RPi400 which we want to
detect, so we can enable Ethernet on it and know the correct device tree
file name.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Reviewed-by: Peter Robinson <pbrobinson@gmail.com> Tested-by: Peter Robinson <pbrobinson@gmail.com> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
rpi: limit size of the RAM to the multiple of the MMU_SECTION_SIZE
When RPi4 is booted from USB Mass Storage, the firmware reports 947MiB of
the ARM memory (948 in case of the standard SD-card boot). This value is
not MMU_SECTION_SIZE aligned, so the dram_bank_mmu_setup() skips mapping
of the last 1MiB. This later causes u-boot in ARM 32bit mode to freeze,
because it relocated itself into that unmapped memory and fails to
execute.
Fix this by limiting the size of the first bank to the multiple of
MMU_SECTION_SIZE.
pci: brcmstb: Cleanup controller state before handover
Make sure we handover the PCIe controller in a clean state. Some of the
devices hanging from the PCIe bus might need to be properly reset
through #PERST in order for Linux to be able to initialize them.
This is specially important in order to properly initialize Raspberry Pi
4 B and 400's USB chip.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
The PCIe bus the controller is connected to might need to be removed
prior the handover. Make sure xhci-pci is also removed so as to avoid
unexpected timeouts or hangs.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
spl: fit: Load devicetree when a Linux payload is found
When a FIT config specifies a devicetree, we should load it, no
questions asked. In the case of the "simple" FIT loading path, a
difficulty arises in selecting the load address of the FDT.
The default FDT location is right after the "kernel" or "firmware"
image. However, if that is an OP-TEE image, then the FDT may end up in
secure DRAM, and not be accessible to normal world kernels.
Although the best solution is to be more careful about the FDT
address, a viable workaround is to only append the FDT after a u-boot
or Linux image. This is identical to the previous logic, except that
FDT loading is extended to IH_OS_LINUX images.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
spl: fit: Replace #ifdef blocks with more readable constructs
Use the IS_ENABLED() macro to control code flow, instead of the
caveman approach of sprinkling #ifdefs. Code size is not affected, as
the linker garbage-collects unused functions. However, readability is
improved significantly.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
image: Do not #if guard board_fit_image_post_process() prototype
There's no point in guarding function prototypes with #ifdefs. If a
function is not defined, the linker will notice. Having the prototype
does not affect code size.
What the #if guard takes away is the ability to use IS_ENABLED:
if (CONFIG_IS ENABLED(FIT_IMAGE_POST_PROCESS))
board_fit_image_post_process(...)
When the prototype is guarded, the above form cannot be used. This
leads to the proliferation of #ifdefs, and unreadable code. The
opportunity cost of the #if guard outweighs any benefits. Remove it.
Since the original version of this patch, an empty definition was
added by commit f14e6eec6c7f ("image: cleanup pre-processor usage").
The empty definition can cause silent failures, when an implementation
of board_fit_image_post_process() is expected because the linker will
not catch the missing function. Thus this patch removes this empty
inline declaration.
Fixes: f14e6eec6c7f ("image: cleanup pre-processor usage") Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
spl: fit: Only look up FIT configuration node once
The configuration node a sub node under "/configurations", which
describes the components to load from "/images". We only need to
locate this node once.
However, for each component, spl_fit_get_image_name() would parse the
FIT image, looking for the correct node. Such work duplication is not
necessary. Instead, once the node is found, cache it, and re-use it.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
spl: fit: Remove useless loop in spl_fit_get_image_name()
When a desired configuration is not found, conf_node will have a
negative value. Thus the for loop will start at the root "/" node of
the image, print the "/description" property, and stop.
It appears the intent of the loop was to print the names of the
subnodes under "/configurations". We would need the offset to the
"/configurations" node, which is abstracted by fit_find_config_node().
This change agrees that abstracting the node offset is the correct
design, and we shouldn't be parsing the configurations manually. Thus
the loop in spl_fit_get_image_name() is useless. Remove it.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
spl: fit: Pass FIT context via a structure pointer
Several loose arguments describe the FIT image. They are thus related,
and it makes sense to pass them together, in a structure. Examples
include the FIT blob pointer, offset to FDT nodes, and the offset to
external data.
Use a spl_fit_info structure to group these parameters.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
spl: fit: Factor out FIT parsing and use a context struct
The logical steps in spl_load_simple_fit() are difficult to follow.
I think the long comments, ifdefs, and ungodly number of variables
seriously affect the readability. In particular, it violates section 6
of the coding style, paragraphs (3), and (4).
The purpose of this patch is to improve the situation by
- Factoring out initialization and parsing to separate functions
- Reduce the number of variables by using a context structure
This change introduces no functional changes.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
spl: fit: Drop 'length' argument to board_spl_fit_post_load()
The size is derived from the FIT image itself. Any alignment
requirements are machine-specific and known by the board code. Thus
the total length can be derived from the FIT image and knowledge of
the platform. The 'length' argument is redundant. Remove it.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org> CC: Matt Porter <mporter@konsulko.com>
Alex Marginean [Mon, 25 Jan 2021 12:23:56 +0000 (14:23 +0200)]
arm: dts: ls1028a: Add Ethernet switch node and dependencies
The definition follows the DSA binding in kernel and describes the switch,
its ports and PHYs. The switch node has the same structure as in Linux
and this patch enables it (and relevant ports) for the LS1028A RDB board.
ENETC PF6 is the 2nd Eth controller linked to the switch on LS1028A, it is
not used in U-Boot and was disabled. Ethernet port aliases were also
added to better manage the multitude of ports available now.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Michael Walle <michael@walle.cc>
Alex Marginean [Mon, 25 Jan 2021 12:23:55 +0000 (14:23 +0200)]
drivers: net: Add Felix DSA switch driver
This driver is used for the Ethernet switch integrated into LS1028A NXP.
Felix on LS1028A has 4 front panel ports and two internal ports, I/O
to/from the switch is done through an ENETC Ethernet interface.
The 4 front panel ports are available as Ethernet interfaces and can be
used with the typical network commands like tftp.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Claudiu Manoil [Mon, 25 Jan 2021 12:23:53 +0000 (14:23 +0200)]
net: Introduce DSA class for Ethernet switches
DSA stands for Distributed Switch Architecture and it covers switches that
are connected to the CPU through an Ethernet link and generally use frame
tags to pass information about the source/destination ports to/from CPU.
Front panel ports are presented as regular ethernet devices in U-Boot and
they are expected to support the typical networking commands.
DSA switches may be cascaded, DSA class code does not currently support
this.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Vladimir Oltean [Mon, 25 Jan 2021 12:23:52 +0000 (14:23 +0200)]
net: phy: introduce fixed_phy_create for DSA CPU ports
The DSA (Distributed Switch Architecture) implementation has made a
design decision when it got introduced to the Linux kernel in 2008.
That was to hide away from the user the CPU-facing Ethernet MAC, since
it does not make sense to register it as a struct net_device (UCLASS_ETH
udevice for U-Boot), because that would never be beneficial for a user:
they would not be able to use it for traffic, since conceptually, a
packet delivered to the CPU port should loop back into the system.
Nonetheless, DSA has had numerous growing pains due to the lack of a
struct net_device for the CPU port, but so far it has overcome them.
It is unlikely at this stage of maturity that this aspect of it will
change.
We would like U-Boot to present the same information as Linux, to be at
parity in terms of number of interfaces, so that ethNaddr environment
variables could directly be associated between U-Boot and Linux.
Therefore, we would implicitly like U-Boot to hide the CPU port from the
user as well.
But the paradox is that DSA still needs a struct phy_device to inform
the driver of the parameters of the link that it should configure the
CPU port to. The problem is that the phy_device is typically returned
via a call to phy_connect, which needs an udevice to attach the PHY to,
and to search its ofnode for the 'fixed-link' property. But we don't
have an udevice to present for the CPU port.
Since 99% of DSA setups are MAC-to-MAC connections between the switch
and the host Ethernet controller, the struct phy_device is going to be a
fixed PHY. This simplifies things quite a bit. In U-Boot, a fixed PHY
does not need an MDIO bus, and does not need an attached dev either.
Basically, the phy_connect call doesn't do any connection, it just
creates the fixed PHY.
The proposal of this patch is to introduce a new fixed_phy_create
function which will take a single argument: the ofnode that holds this:
port@4 {
reg = <4>;
phy-mode = "internal";
fixed-link {
speed = <2500>;
full-duplex;
};
};
and probe a fixed PHY driver using the information from this ofnode.
DSA will probably be the only user of this function.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Vladimir Oltean [Mon, 25 Jan 2021 12:23:51 +0000 (14:23 +0200)]
net: phy: fixed: support speeds of 2500 and 10000
Unlike the Linux fixed PHY driver, the one in U-Boot does not attempt to
emulate the clause 22 register set of a gigabit copper PHY driver
through the swphy framework. Therefore, the limitation of being unable
to support speeds higher than gigabit in fixed-link does not apply to
the U-Boot fixed PHY driver. This makes the fixed-link U-Boot
implementation more similar to the one from phylink, which can work with
any valid link speed.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Igor Opaniuk [Mon, 25 Jan 2021 12:28:43 +0000 (14:28 +0200)]
test: dm: tee: extend with RPC test
Extend existing DM tee tests adding test coverage for reverse RPC calls.
Currently this commit only adds tests for I2C requests from TEE driver
to TEE supplicant, for instance reading/writing data to emulated i2c
eeprom defines in standard sandbox test device tree
(arch/sandbox/dts/test.dtb):
=> i2c bus
Bus 0: i2c@0 (active 0)
2c: eeprom@2c, offset len 1, flags 0
...
Running TEE tests:
=> ut dm tee
Test: dm_test_tee: tee.c
Test: dm_test_tee: tee.c (flat tree)
Failures: 0
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Etienne Carriere <etienne.carriere@linaro.org>
Igor Opaniuk [Mon, 25 Jan 2021 12:28:42 +0000 (14:28 +0200)]
drivers: tee: sandbox: add rpc test ta emulation
This adds support for RPC test trusted application emulation, which
permits to test reverse RPC calls to TEE supplicant. Currently it covers
requests to the I2C bus from TEE.
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org> Acked-by: Etienne Carriere <etienne.carriere@linaro.org>
This commit gives the secure world access to the I2C bus so it can
communicate with I2C slaves (typically those would be secure elements
like the NXP SE050).
A similar service implementation has been merged in linux: c05210ab ("drivers: optee: allow op-tee to access devices on the i2c
bus")
Andy Shevchenko [Thu, 11 Feb 2021 15:09:44 +0000 (17:09 +0200)]
usb: kbd: destroy device after console is stopped
In case of IOMUX enabled it assumes that console devices in the list
are available to get them stopped properly via ->stop() callback.
However, the USB keyboard driver violates this assumption and tries
to play tricks so the device get destroyed while being listed as
an active console.
Swap the order of device deregistration and IOMUX update along with
converting to use iomux_replace_device() jelper to avoid the use-after-free.
Fixes: 3cbcb2892809 ("usb: Fix usb_kbd_deregister when console-muxing is used") Fixes: 8a8348703081 ("dm: usb: Add a remove() method for USB keyboards") Reported-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Andy Shevchenko [Thu, 11 Feb 2021 15:09:43 +0000 (17:09 +0200)]
IOMUX: Introduce iomux_replace_device()
Some console devices may appear or disappear at run time. In order to
support such a hotplug mechanism introduce a new iomux_replace_device()
helper to update the list of devices without altering environment.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Andy Shevchenko [Thu, 11 Feb 2021 15:09:42 +0000 (17:09 +0200)]
IOMUX: Split out for_each_console_dev() helper macro
It is not only less lines of code, but also better readability
when new macro is being in use. Introduce for_each_console_dev()
helper macro and convert current users to it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Andy Shevchenko [Thu, 11 Feb 2021 15:09:38 +0000 (17:09 +0200)]
console: Set console device counter in console_devices_set()
console_devices_set() missed the console device counter to be set correctly.
Fixes: 45375adc9799 ("console: add function console_devices_set") Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Fix CVE-2021-27097 and CVE-2021-27138. For more details see
http://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2021-27097 and
http://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2021-27138
Simon Glass [Tue, 16 Feb 2021 00:08:11 +0000 (17:08 -0700)]
libfdt: Check for multiple/invalid root nodes
It is possible to construct a devicetree blob with multiple root nodes.
Update fdt_check_full() to check for this, along with a root node with an
invalid name.
CVE-2021-27097
Signed-off-by: Simon Glass <sjg@chromium.org> Reported-by: Bruce Monroe <bruce.monroe@intel.com> Reported-by: Arie Haenel <arie.haenel@intel.com> Reported-by: Julien Lenoir <julien.lenoir@intel.com>
Simon Glass [Tue, 16 Feb 2021 00:08:09 +0000 (17:08 -0700)]
image: Adjust the workings of fit_check_format()
At present this function does not accept a size for the FIT. This means
that it must be read from the FIT itself, introducing potential security
risk. Update the function to include a size parameter, which can be
invalid, in which case fit_check_format() calculates it.
For now no callers pass the size, but this can be updated later.
Also adjust the return value to an error code so that all the different
types of problems can be distinguished by the user.
Signed-off-by: Simon Glass <sjg@chromium.org> Reported-by: Bruce Monroe <bruce.monroe@intel.com> Reported-by: Arie Haenel <arie.haenel@intel.com> Reported-by: Julien Lenoir <julien.lenoir@intel.com>
projects / u-boot.git / log
