Michal Simek [Tue, 3 Dec 2019 14:02:50 +0000 (15:02 +0100)]
arm64: zynqmp: Do not assing MIO34 that early on zcu100
MIO34 is connected to POWER_KILL signal. When MIO configuration is done in
psu_init() and this pin is assigned to PMU but PMU configuration is not
loaded yet. PMU gpio output is high that means board is powered off
immediately.
The patch is fixing this sequence that MIO34 stays assing to ps gpio IP.
PMU config is loaded in SPL and then pin assigned to PMU through
psu_post_config_data().
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 20 Dec 2019 10:35:52 +0000 (11:35 +0100)]
arm64: Enable INIT_SP_RELATIVE by default when POC is enabled
When position-independent pre-relocation code is enable there is also
necessary to enable relative early stack pointer not to use origin location
pointed by CONFIG_SYS_INIT_SP_ADDR macro.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 19 Dec 2019 12:56:33 +0000 (13:56 +0100)]
arm64: zynqmp: Do not call bss init and board_init_r from board_init_f
There is no reason to clear bss and call board_init_r() from board_init_f()
beca it can be called directly from crt0_64.S with also support for SPL
stack relocation to SDRAM.
For more information please take a look at arch/arm/lib/crt0_64.S
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 19 Dec 2019 14:42:13 +0000 (15:42 +0100)]
spl: atf: Add missing ndepth initialization
ndepth needs to be initialized before it is used in fdt_next_node().
Uninitialized value is causing that node is found and depth increase but
won't pass condition below because initial state wasn't setup.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
T Karthik Reddy [Wed, 18 Dec 2019 10:34:41 +0000 (03:34 -0700)]
board: xilinx: Add support for user configurable boot script offset
Currently "script_offset_f" env variable is hardcoded, this variable
specifies from which offset of the flash boot.scr should be read/write.
As flashes are of different sizes having a fixed offset makes it
difficult to load other images into the flash which may overwrite the
boot script or cannot utilize the full memory. This current fix
creates a new config "CONFIG_BOOT_SCRIPT_OFFSET" which holds the
offset address, overwrites the "script_offset_f" variable.
Also removed existing variable with default values, as the default
values are held by CONFIG_BOOT_SCRIPT_OFFSET
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Emmc boot devcie is mounted to mmc@ff160000 controller on zynqmp.
Detect mmc alias at run time for setting up proper boot_targets
sequence instead of setting boot_targets manually.
Removed setting "modeboot" variable as it not longer need as we
switched to distro boot.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Emmc boot devcie is mounted to sdhci@f1050000 controller on versal, while
in emmc boot mode, boot tragets are set to mmc0. So removed mmc0 and using
the dev seq number from the sdhci@f1050000 controller.
Dev seq number is setup based on DT aliases that's why needs to be setup at
run time.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Eugeniu Rosca [Tue, 24 Dec 2019 16:51:08 +0000 (17:51 +0100)]
cmd: adtimg: Refactor usage style
Trying to extend 'adtimg' functionality [1], we've been severely hit
by a major limitation in the command's usage scheme. Specifically, the
command's user interface appears to be too centric to getting the
DTB/DTBO entry [3] based on the index of the desired DT in the image,
which makes it really difficult retrieving the DT entry based on
alternative criteria (e.g. filtering by id/rev fields), the
latter being demanded by real life customer use-cases [1].
This went to the point of receiving below feedback from Sam [2]:
-- snip --
As for 'dtimg' command: after giving it some thought, I think not much
people using it yet. So in this particular case I don't have some
strong preference, and if you think the 'dtimg' interface is ugly, and
it overcomes "don't break interfaces" rule, maybe now is a good time
to rework it (before it gets widely used).
-- snip --
Given the above, rework the usage pattern from [4] to [5], in order to
allow an intuitive enablement of "by id|rev" DT search [6].
[1] https://patchwork.ozlabs.org/cover/1202575/
("cmd: dtimg: Enhance with --id and --rev options (take #1)")
[2] https://patchwork.ozlabs.org/patch/1182207/#2317020
[3] https://source.android.com/devices/architecture/dto/partitions
[4] Old usage
adtimg dump <addr> - Print image contents
adtimg start <addr> <index> <varname> - Get DT address by index
adtimg size <addr> <index> <varname> - Get DT size by index
[5] New usage
adtimg addr <addr> - Set image location to <addr>
adtimg dump - Print out image contents
adtimg get dt --index=<i> [avar [svar]] - Get DT address and size by index
[6] Soon-to-be-provided "by id|rev" add-on functionality
adtimg get dt --id=<id> --rev=<rev> [avar [svar [ivar]]]
- Get DT address/size/index by id|rev fields
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Eugeniu Rosca [Tue, 24 Dec 2019 16:51:06 +0000 (17:51 +0100)]
dtimg/am57xx_evm_defconfig: Rename dtimg to adtimg
Rename the existing 'dtimg' command to 'adtimg', in order to:
- Suggest the Android origins and scope
- Be consistent with the upcoming 'abootimg' command (naming
suggested by Simon [*])
The change in _not_ backward compatible, but its benefits outweigh its
downsides, given that we don't expect active users of 'dtimg' today.
Perform the rename in several steps:
1. Rename *.c file and Kconfig symbol. This should allow
'git log --follow' to properly track the history of 'adtimg.c'
2. 's/dtimg/adtimg/g' in the internal namespace of 'adtimg.c'
ELF comparison [**] before and after shows no functional change.
Cc: Tom Rini <trini@konsulko.com> Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Reviewed-by: Simon Glass<sjg@chromium.org> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Rajesh Ravi [Fri, 22 Nov 2019 22:50:01 +0000 (14:50 -0800)]
arm: cpu: armv8: add support for arm psci reset2.
Current U-Boot has only support for psci reset.
Adding support for arm psci reset2 allows passing of reset level
and other platform sepcific parameters like strap settings
to lowlevel psci implementation.
Signed-off-by: Rajesh Ravi <rajesh.ravi@broadcom.com> Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Programs the following:
1. Redistributor PROCBASER configuration table (which
is common for all redistributors)
2. Redistributor pending table (PENDBASER), for all the
available redistributors.
Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com> Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Philippe Reynes [Thu, 9 Jan 2020 16:34:02 +0000 (17:34 +0100)]
test/cmd_ut.c: fix cmd_ut_category
In the function cmd_ut_category, the prefix is used with
the function strncmp to know if the prefix should be
removed from the test name, even if the prefix is NULL.
To avoid this issue, we consider that a prefix NULL
mean no prefix. So we only try to remove the prefix
from the test_name if the prefix is not NULL, then
we avoid to call the function strncmp with a NULL
prefix.
Reported-by: Coverity CID 281110 Fixes: 4ad4edfe ("cmd_ut: add a parameter prefix to the function cmd_ut_category") Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Andy Shevchenko [Fri, 29 Nov 2019 17:47:59 +0000 (19:47 +0200)]
gcc-9: silence 'address-of-packed-member' warning
GCC 9.x starts complaining about potential misalignment of the pointer to
the array (in this case alignment=2) in the packed (alignment=1) structures.
Repeating Linus' Torvalds commit 6f303d60534c in the Linux kernel.
Original commit message:
We already did this for clang, but now gcc has that warning too.
Yes, yes, the address may be unaligned. And that's kind of the point.
This in particular hides the warnings like
drivers/usb/gadget/composite.c:545:23: warning: taking address of packed member of ‘struct usb_string_descriptor’ may result in an unaligned pointer value [-Waddress-of-packed-member]
545 | collect_langs(sp, s->wData);
drivers/usb/gadget/composite.c:550:24: warning: taking address of packed member of ‘struct usb_string_descriptor’ may result in an unaligned pointer value [-Waddress-of-packed-member]
550 | collect_langs(sp, s->wData);
drivers/usb/gadget/composite.c:555:25: warning: taking address of packed member of ‘struct usb_string_descriptor’ may result in an unaligned pointer value [-Waddress-of-packed-member]
555 | collect_langs(sp, s->wData);
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Holger Brunck [Mon, 25 Nov 2019 16:24:14 +0000 (17:24 +0100)]
km/boards: add MAC address offset as argument to ivm_populate_env
For upcoming SECU board we have different MAC address offsets depending
on which functional unit we are running. In this case we need to pass
this value to the ivm_populate_env function instead of using the hard
coded config option there.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com> CC: Stefan Roese <sr@denx.de> CC: Valentin Longchamp <valentin.longchamp@ch.abb.com> CC: Marek Vasut <marex@denx.de> Reviewed-by: Stefan Roese <sr@denx.de>
Han Nandor [Tue, 12 Nov 2019 08:39:38 +0000 (08:39 +0000)]
rtc: add support for DS3232 device
DS3232 is an i2c RTC with 236 bytes of battery-backed SRAM.
Add an RTC driver for DS3232 device, which provides time and
date support. Also read and write functions are provided,
which can be used to access the SRAM memory.
Signed-off-by: Nandor Han <nandor.han@vaisala.com>
spl: fix stack usage check if gd is not initialized
Most platforms do not set up gd->start_addr_sp in SPL. Since this is
required for CONFIG_SPL_SYS_REPORT_SACK_F_USAGE to work correctly, set
up gd->start_addr_sp in SPL to the value passed to
board_init_f_init_reserve if it is not set yet.
Tom Rini [Wed, 8 Jan 2020 23:57:11 +0000 (18:57 -0500)]
Merge tag 'efi-2020-04-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-04-rc1
This pull request provides:
* support for FIT images for UEFI binaries
* drivers for hardware random number generators
* an implementation of the EFI_RNG_PROTOCOL
* a sub-command for efidebug to display configuration tables
Peng Ma [Wed, 4 Dec 2019 10:36:45 +0000 (10:36 +0000)]
ata: fsl_sata: Continue probing other sata port when failed current port.
In the initialization of sata driver, we want to initialize all port
probes, Therefore, any detection failure between of them should continue
initialization by skipping the current port instead of exit.
Peng Ma [Wed, 4 Dec 2019 10:36:42 +0000 (10:36 +0000)]
ata: sata_sil: Continue probing other sata port when failed current port.
In the initialization of sata driver, we want to initialize all port
probes, Therefore, any detection failure between of them should continue
initialization by skipping the current port instead of exit.
Patrice Chotard [Fri, 6 Dec 2019 14:01:49 +0000 (15:01 +0100)]
treewide: Remove CONFIG_SYS_UBOOT_START from configs board files
As previous CONFIG_SYS_UBOOT_START is now set by default to
CONFIG_SYS_TEXT_BASE when not defined, CONFIG_SYS_UBOOT_START
can be removed from include/configs board files.
Peng Fan [Mon, 6 Jan 2020 08:16:32 +0000 (16:16 +0800)]
imx: imx8mn_evk: add board_mmc_get_env_dev
Add board_mmc_get_env_dev, otherwise,
Loading Environment from MMC...
MMC Device 0 not found
*** Warning - No MMC card found, using default environment
Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
CPU: Freescale i.MX8MP rev1.0 at 1000 MHz
Reset cause: POR
Model: NXP i.MX8MPlus EVK board
DRAM: 6 GiB
MMC: FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Hit any key to stop autoboot: 0
u-boot=> mmc list
FSL_SDHC: 1 (SD)
FSL_SDHC: 2
Peng Fan [Mon, 30 Dec 2019 08:52:30 +0000 (16:52 +0800)]
imx: imx8m: only support non-dm code in clock_imx8mm.c
The drivers/clk/imx/*.c are used for CLK dm case, the
clock_imx8mm.c is used for non CLK dm case, let's split
it. Sometimes it is hard to enable CLK dm in SPL stage,
considering code size, malloc size requirement, the splittion
will make it easy to use non CLK dm in SPL stage.
Peng Fan [Mon, 30 Dec 2019 02:03:44 +0000 (10:03 +0800)]
arm: dts: freescale: Add i.MX8MP dtsi support
The i.MX8M Plus Media Applications Processor is part of the growing
mScale family targeting the consumer and industrial market. It brings
an effective Machine Learning and AI accelerator that enables a new
class of applications. It is built in Samsung 14LPP to achieve both
high performance and low power consumption and relies on a powerful
fully coherent core complex based on a quad core ARM Cortex-A53 cluster
and Cortex-M7 low-power coprocessor, audio digital signal processor,
machine learning and graphics accelerators.
Add the basic dtsi support for i.MX8MP.
Patch from Anson Huang for Kernel
https://patchwork.kernel.org/patch/11310915/
Peng Fan [Wed, 11 Dec 2019 06:17:12 +0000 (06:17 +0000)]
imx: imx8mq: handle ESDHC in mxc_get_clock
fsl_esdhc_imx driver will call "mxc_get_clock(MXC_ESDHC_CLK +
dev->seq)", however mxc_get_clock wrongly handle MXC_ESDHC_CLK
as root clk and cause sd card could not be detected in U-Boot proper,
as below:
"Loading Environment from MMC... unable to select a mode"
Handle MXC_ESDHC_CLK in mxc_get_clock to fix the issue.
Rasmus Villemoes [Thu, 19 Dec 2019 09:46:08 +0000 (09:46 +0000)]
mpc83xx_clk: always treat MPC83XX_CLK_PCI as invalid
The current mpc83xx_clk driver is broken for any board for which
mpc83xx_has_pci() is true, i.e. anything not MPC8308:
When is_clk_valid() reports that MPC83XX_CLK_PCI is valid,
init_all_clks() proceeds to call init_single_clk(), but that doesn't
know about either MPC83XX_CLK_PCI or has any handling of the
TYPE_SCCR_ONOFF mode correctly returned by retrieve_mode(). Hence
init_single_clk() ends up returning -EINVAL, and the whole board hangs
in serial_init().
The quickest fix is to simply pretend that clock is invalid for
all, since nobody can have been relying on it. Adding proper support
seems to be a bit more involved than just handling TYPE_SCCR_ONOFF:
- The power-on-reset value of SCCR[PCICM] is 0, so
mpc83xx_clk_enable() would probably need to be tought to enable the
clock.
- The frequency of PCI_SYNC_OUT is either SYS_CLK_IN or SYS_CLK_IN/2
depending on the CFG_CLKIN_DIV configuration input, but that can't
be read from software, so to properly fill out
->speed[MPC83XX_CLK_PCI] I think one would need guidance from
Kconfig or dtb.
Rasmus Villemoes [Wed, 11 Dec 2019 09:39:36 +0000 (09:39 +0000)]
mpc83xx: make ARCH_MPC8309 select SYS_FSL_ERRATUM_ESDHC111
The mpc8309 is also affected by the "Manual Asynchronous CMD12 abort
operation causes protocol violations" erratum, though it is enumerated
as eSDHC16 in the errata sheet for mpc8309.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Reviewed-by: Mario Six <mario.six@gdsys.cc>
Sean Anderson [Wed, 25 Dec 2019 04:52:01 +0000 (23:52 -0500)]
dm: Add a debug message when devices are skipped pre-reloc
This adds a message to lists_bind_fdt when it skips initializing a device
pre-relocation. I've had a couple errors where a device didn't initialize
properly because one of its dependencies was missing.
Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Mon, 30 Dec 2019 04:19:27 +0000 (21:19 -0700)]
dm: devres: Use an enum for the allocation phase
At present we only support two phases where devres can be used:
bind and probe. This is handled with a boolean. We want to add a new
phase (platdata), so change this to an enum.
projects / u-boot.git / log
