Philippe Reynes [Wed, 23 Dec 2020 14:33:07 +0000 (15:33 +0100)]
cmd: ubi: don't allow to rename a volume to a name that already exist
This commits add a check on the command ubi rename. This check avoids
to rename a volume to with a name that is already used on another ubi
volume. If two volumes has the same name, then the ubi device can't be
mounted anymore.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Stefan Agner [Wed, 30 Dec 2020 12:16:36 +0000 (13:16 +0100)]
nvme: Use only 32-bit accesses in nvme_writeq/nvme_readq
There might be hardware configurations where 64-bit data accesses
to NVMe registers are not supported properly. This patch removes
the readq/writeq so always two 32-bit accesses are used to read/write
64-bit NVMe registers, similarly as it is done in Linux kernel.
This patch fixes operation of NVMe devices on RPi4 Broadcom BCM2711 SoC
based board, where the PCIe Root Complex, which is attached to the
system through the SCB bridge.
Even though the architecture is 64-bit the PCIe BAR is 32-bit and likely
the 64-bit wide register accesses initiated by the CPU are not properly
translated to a sequence of 32-bit PCIe accesses.
nvme_readq(), for example, always returns same value in upper and lower
32-bits, e.g. 0x3c033fff3c033fff which lead to NVMe devices to fail
probing.
This fix is analogous to commit 8e2ab05000ab ("usb: xhci: Use only
32-bit accesses in xhci_writeq/xhci_readq").
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com> Cc: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Cc: Matthias Brugger <mbrugger@suse.com> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Stefan Agner <stefan@agner.ch>
Sughosh Ganu [Wed, 30 Dec 2020 13:57:09 +0000 (19:27 +0530)]
efi: capsule: Add support for uefi capsule authentication
Add support for authenticating uefi capsules. Most of the signature
verification functionality is shared with the uefi secure boot
feature.
The root certificate containing the public key used for the signature
verification is stored as part of the device tree blob. The root
certificate is stored as an efi signature list(esl) file -- this file
contains the x509 certificate which is the root certificate.
Sughosh Ganu [Wed, 30 Dec 2020 13:57:08 +0000 (19:27 +0530)]
efi_loader: Re-factor code to build the signature store from efi signature list
The efi_sigstore_parse_sigdb function reads the uefi authenticated
variable, stored in the signature database format and builds the
signature store structure. Factor out the code for building
the signature store. This can then be used by the capsule
authentication routine to build the signature store even when the
signature database is not stored as an uefi authenticated variable
Sughosh Ganu [Wed, 30 Dec 2020 13:57:07 +0000 (19:27 +0530)]
efi_loader: Make the pkcs7 header parsing function an extern
The pkcs7 header parsing functionality is pretty generic, and can be
used by other features like capsule authentication. Make the function
an extern, also changing it's name to efi_parse_pkcs7_header
Sughosh Ganu [Wed, 30 Dec 2020 13:57:06 +0000 (19:27 +0530)]
dfu_mtd: Add provision to unlock mtd device
Prior to writing to an mtd device, mtd_erase is called. This call
fails in case the sector being erased is locked. Call mtd_unlock to
unlock the region which is to be erased and later written to. Lock the
region once the write to the region has completed.
Sughosh Ganu [Wed, 30 Dec 2020 13:57:05 +0000 (19:27 +0530)]
efi_loader: Add logic to parse EDKII specific fmp payload header
When building the capsule using scripts in edk2, a fmp header is
added on top of the binary payload. Add logic to detect presence of
the header. When present, the pointer to the image needs to be
adjusted as per the size of the header to point to the actual binary
payload.
Sughosh Ganu [Wed, 30 Dec 2020 13:57:04 +0000 (19:27 +0530)]
fsp: Move and rename fsp_types.h file
The fsp_types.h header file contains macros for building signatures of
different widths. These signature macros are architecture agnostic,
and can be used in all places which use signatures in a data
structure. Move and rename the fsp_types.h under the common include
header.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Sughosh Ganu [Wed, 30 Dec 2020 13:57:03 +0000 (19:27 +0530)]
qemu: common: Set dfu_alt_info variable for the platform
The dfu framework uses the dfu_alt_info environment variable to get
information that is needed for performing the firmware update. Add
logic to set the dfu_alt_info for the qemu arm64 platform to reflect
the two mtd partitions created for the u-boot env and the firmware
image. This can be subsequently extended for other qemu architectures
which need this variable set.
Sughosh Ganu [Wed, 30 Dec 2020 13:57:02 +0000 (19:27 +0530)]
qemu: common: Add support for dynamic mtdparts for the platform
Add support for setting the default values for mtd partitions on the
platform. This would be used for updating the firmware image using
uefi capsule update with the dfu mtd backend driver.
Currently, values have been defined for the qemu arm64 platform, with
default values defined for the mtd partitions based on the NOR
flash. This can be subsequently extended for other qemu architectures
which need mtdparts set.
Sughosh Ganu [Wed, 30 Dec 2020 13:57:01 +0000 (19:27 +0530)]
crypto: Fix the logic to calculate hash with authattributes set
RFC 2315 Section 9.3 describes the message digesting process. The
digest calculated depends on whether the authenticated attributes are
present. In case of a scenario where the authenticated attributes are
present, the message digest that gets signed and is part of the pkcs7
message is computed from the auth attributes rather than the contents
field.
Check if the auth attributes are present, and if set, use the auth
attributes to compute the hash that would be compared with the
encrypted hash on the pkcs7 message.
Sughosh Ganu [Wed, 30 Dec 2020 13:57:00 +0000 (19:27 +0530)]
qemu: arm: Initialise virtio devices in board_late_init
On the qemu arm platform, the virtio devices are initialised in the
board_init function, which gets called before the initr_pci. With
this sequence, the virtio block devices on the pci bus are not
initialised. Move the initialisation of the virtio devices to
board_late_init which gets called after the call to initr_pci.
Sughosh Ganu [Wed, 30 Dec 2020 13:56:59 +0000 (19:26 +0530)]
mkeficapsule: Add support for embedding public key in a dtb
Add options for embedding the public key esl(efi signature list) file
to the platform's dtb. The esl file is then retrieved and used for
authenticating the capsule to be used for updating firmare components
on the platform.
The esl file can now be embedded in the dtb by invoking the following
command
mkeficapsule -K <pub_key.esl> -D <dtb>
In the scenario where the esl file is to be embedded in an overlay,
this can be done through the following command
mkeficapsule -O -K <pub_key.esl> -D <dtb>
This will create a node named 'signature' in the dtb, and the esl file
will be stored as 'capsule-key'
When a new event is queued we have to process the event queue by calling
efi_process_event_queue(). But there is not reason to call the function
when the event is not queueable.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Ilias Apalodimas [Thu, 31 Dec 2020 10:26:46 +0000 (12:26 +0200)]
efi_loader: Add size checks to efi_create_indexed_name()
Although the function description states the caller must provide a
sufficient buffer, it's better to have in function checks that the
destination buffer can hold the intended value.
So let's add an extra argument with the buffer size and check that
before doing any copying.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Ilias Apalodimas [Wed, 30 Dec 2020 15:07:14 +0000 (17:07 +0200)]
efi_loader: Remove unconditional installation of file2 protocol for initrd
Up to now we install the EFI_LOAD_FILE2_PROTOCOL to load an initrd
unconditionally. Although we correctly return various EFI exit codes
depending on the file status (i.e EFI_NO_MEDIA, EFI_NOT_FOUND etc), the
kernel loader only falls back to the cmdline interpreted initrd if the
protocol is not installed.
This creates a problem for EFI installers, since they won't be able to
load their own initrd and start the installation.
A following patch introduces a different logic where we search for an
initrd path defined in an EFI variable named 'Initrd####'.
If the bootmgr is used to launch the EFI payload, we'll will try to match
the BootCurrent value and find the corresponding initrd
(i.e Boot0000 -> Initrd0000 etc). If the file is found, we'll install
the required protocol which the kernel's efi-stub can use and load our
initrd.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The FAT filesystem implementation uses several marcros referring to a magic
variable name mydata which renders the code less readable. Eliminate one of
them which is only used for a debug() statement.
Use log_debug() instead of debug().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Ilias Apalodimas [Wed, 23 Dec 2020 11:25:00 +0000 (13:25 +0200)]
efi_loader: Extra checks while opening an OPTEE session
When opening an OP-TEE session we need to check the internal return
value of OP-TEE call arguments as well the return code of the
function itself.
The code was also ignoring to close the OP-TEE session in case the
shared memory registration failed.
Fixes: f042e47e8fb43 ("efi_loader: Implement EFI variable handling via OP-TEE") Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This change revers code which asserting PERST# signal when unloading
driver. Driver's remove callback is still there as it is used for other
functionality.
Asserting PERST# signal prior booting kernel is causing that A3720 boards
(Turris MOX and Espressobin) with stable Linux kernel versions 4.14 and
4.19 are not able to detect some PCIe cards (e.g. Compex WLE200 and WLE900)
and anymore. When PERST# signal is not asserted these cards are detected
correctly. As this is regression for existing stable Linux kernel versions
revert this problematic change in U-Boot.
To make cards working with OpenWRT 4.14 kernel it is needed to disable link
training prior booting kernel, which is already done in driver's remove
callback.
Described issue is in Linux kernel pci aardvark driver which is (hopefully)
fixed in latest upstream versions. Latest upstream versions should be able
to initialize PCIe bus and detects cards independently of the link training
and PERST# signal state.
So with this change, U-Boot on A3720 boards should be able to boot OpenWRT
4.14 kernel, stable 4.14 and 4.19 kernels and also latest mainline kernels.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Stefan Roese [Thu, 10 Dec 2020 05:40:10 +0000 (06:40 +0100)]
arm: mvebu: Add armada-xp-gp-u-boot.dtsi for U-Boot properties
Add some missing "u-boot,dm-pre-reloc;" properties to UART0, SPI
controller and SPI NOR flash node to enable usage in SPL. Otherwise
these devices will not be available.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Dennis Gilmore <dgilmore@redhat.com> Tested-by: Dennis Gilmore <dgilmore@redhat.com>
Marc Ferland [Tue, 22 Dec 2020 19:24:12 +0000 (14:24 -0500)]
arm: dart6ul: read and print SoM info from eeprom on startup
The dart6ul has an i2c eeprom at 0x50 which contains, among other
things, the manufacturing/revision/options info of the SoM. This patch
replaces the current checkboard() implementation with a more
exhaustive one based on the content of the eeprom.
Since this code uses the new driver model, some changes were also
required in the DTS to make the nodes related to i2c available before
relocation.
This code was inspired from the supported u-boot code from Variscite
which can be found here:
Igor Opaniuk [Tue, 22 Dec 2020 15:56:46 +0000 (17:56 +0200)]
toradex: hand over maintainership
Hand over maintainership of Toradex SoMs (that I was responsible of) to
Oleksandr because of my resignation from Toradex, as such I will
have no immediate involvement with these modules and as a result not
able to continue maintaining these boards.
1. Configure 125MHz clock
2. Setup the TX clock delay (RX is enabled by default),
3. Setup reserved bits to avoid voltage peak
The clock delays are nowadays already configured by the
PHY driver (in ar803x_delay_config). The code for that
can simply be dropped. The clock speed can also be
configured by the PHY driver by adding the device tree
property "qca,clk-out-frequency".
What is left is setting up the undocumented reserved bits
to avoid the voltage peak problem. I slightly improved its
documentation while updating the board's PHY rework code.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Instead of hardcoding index magic numbers in the board code,
also rely on board_fit_config_name_match choosing the right
config for the fitImage containing the kernel.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Ilias Apalodimas [Wed, 23 Dec 2020 11:25:00 +0000 (13:25 +0200)]
efi_loader: Extra checks while opening an OPTEE session
When opening an OP-TEE session we need to check the internal return
value of OP-TEE call arguments as well the return code of the
function itself.
The code was also ignoring to close the OP-TEE session in case the
shared memory registration failed.
Fixes: f042e47e8fb43 ("efi_loader: Implement EFI variable handling via OP-TEE") Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add a host_build() function, so that it's possible to
check for software being build with USE_HOSTCC without
relying on preprocessor conditions. In other words
#ifdef USE_HOSTCC
host_only_code();
#endif
can be written like this instead:
if (host_build())
host_only_code();
This improves code readability and test coverage and
compiler will eleminate this unreachable code.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Reviewed-by: Simon Glass <sjg@chromium.org>
configs: imx8m: enable eMMC HS400ES and SD UHS mode on EVK
i.MX8M series includes support for high speed modes in uSDHC controllers.
Turn on corresponding configuration options for EVK boards, which would
enable high speed modes to be included in U-Boot.
ARM: dts: imx8m: increase off-on delay on the SD Vcc regulator
Some SD Card controller and power circuitry has increased capacitance,
which keeps the internal logic remains powered after regulator is switch
off. This is generally the case when card is switched to SD104 mode,
where a power cycle should be performed. In case if the card internal
logic remains powered, it causes a subsequent failure of mode
transition, effectively leading to failed enumeration.
Introduce a delay of 20 msec in order to provide a possibility for
internal card circuitry to drain voltages and perform a power cycle
correctly.
Similar fix is done in commit c49d0ac38a76 ("ARM: dts: rmobile: Increase
off-on delay on the SD Vcc regulator") targeted Renesas SOCs.
Adam Ford [Fri, 4 Dec 2020 23:27:46 +0000 (17:27 -0600)]
arm: dts: imx8mm: sync dts from Linux Kernel 5.10-rc6
There have been some updates to the device tree since 5.6.
This also includes some clocks, and makes it easier to keep
board device tree files in sync with Linux
Signed-off-by: Adam Ford <aford173@gmail.com> Acked-by: Peng Fan <peng.fan@nxp.com>
As per kernel commit 0672d22a1924 ("ARM: dts: imx: Fix the AR803X phy-mode)
the correct phy-mode should be "rgmii-id", so fix it accordingly
to fix the Ethernet regression.
Simon Glass [Thu, 17 Dec 2020 00:25:06 +0000 (17:25 -0700)]
dm: core: Inline a few ofnode functions in SPL
A recent change to unify the flattree/livetree code introduced a small
size increase in SPL on some boards. For example SPL code size for
px30-core-ctouch2-px30 increased by 40 bytes.
To address this we can take advantage of the fact that some of the ofnode
functions are only called a few times in SPL, so it is worth inlining
them.
Add new Kconfig options to control this. These functions are not inlined
for U-Boot proper, since this increases code size.
Fixes: 2ebea5eaebf ("dm: core: Combine the flattree and livetree binding code") Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Thu, 17 Dec 2020 00:24:17 +0000 (17:24 -0700)]
buildman: Remove output binaries before building
Buildman reuses build directories from previous builds to avoid the cost
of 'make mrproper' for every build. If the previous build produced an SPL
image but the current one does not, the SPL image will remain and buildman
will think it is a result of building the current board.
Remove these files before building, to avoid this problem.
Niel Fourie [Wed, 16 Dec 2020 11:11:52 +0000 (12:11 +0100)]
dm: spi: Fix spi_free_slave() freed memory write
Remove setting slave->dev to NULL after the device_remove() call.
The slave pointer points to dev->parent_priv, which has already
been freed by device_free(), called from device_remove() in the
preceding line. Writing to slave->dev may cause corruption of the
dlmalloc free chunk forward pointer of the previously freed chunk.
Signed-off-by: Niel Fourie <lusus@denx.de> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Ovidiu Panait [Mon, 14 Dec 2020 17:06:51 +0000 (19:06 +0200)]
test: dm: spi: Add testcase for spi_claim_bus()
Add testcase for spi_claim_bus(), which checks that sandbox spi bus
speed/mode settings are updated correctly when multiple slaves use
the bus consecutively. The following configurations are used for the
two spi slaves involved:
* different max_hz / different modes
* different max_hz / same modes
* different modes / same max_hz
asm/test.h header is added in order to be able to retrieve the current
speed/mode of the sandbox spi bus, via sandbox_spi_get_{speed, mode}.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Currently, when different spi slaves claim the bus consecutively using
spi_claim_bus(), spi_set_speed_mode() will only be executed on the first
two calls, leaving the bus in a bad state starting with the third call.
This patch drops spi_slave->speed member and adds caching of bus
speed/mode in dm_spi_bus struct. It also updates spi_claim_bus() to call
spi_set_speed_mode() if either speed or mode is different from what the
bus is currently configured for. Current behavior is to only take into
account the speed, but not the mode, which seems wrong.
Fixes: 60e2809a848 ("dm: spi: Avoid setting the speed with every transfer") Reviewed-by: Simon Glass <sjg@chromium.org> Reported-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Reported-by: Moshe, Yaniv <yanivmo@amazon.com> Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Introduce sandbox_spi_get_{speed, mode} public interface to retrieve the
sandbox spi bus internal state. They are meant to be used in sandbox spi
testcases.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Ovidiu Panait [Mon, 14 Dec 2020 17:06:48 +0000 (19:06 +0200)]
spi: sandbox_spi: Implement speed/mode setup
Implement sandbox_spi_set_{speed, mode} routines, to be able to keep track
of the current bus speed/mode. This will help determine whether the values
passed from dm_spi_claim_bus() are valid.
Ovidiu Panait [Mon, 14 Dec 2020 17:06:47 +0000 (19:06 +0200)]
sandbox: test: Add a second SPI slave on sandbox_spi bus
Place a second spi slave on the sandbox_spi bus, to be used by the
spi_claim_bus() testcase we are about to introduce. We need to make sure
that jumping between slaves calling spi_claim_bus() sets the bus speed and
mode appropriately. Use different max-hz and mode properties for this new
slave.
Also, update sandbox_spi cs_info call to allow activity on CS0/CS1 and
adapt dm_test_spi_find() testcase for this new setup.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Ovidiu Panait [Mon, 14 Dec 2020 17:06:46 +0000 (19:06 +0200)]
sandbox: spi: Drop unused sandbox_spi_parse_spec function
Commit 1289e96797bf ("sandbox: spi: Drop command-line SPI option") dropped
support for specifying SPI devices on the command line, removing the only
user of sandbox_spi_parse_spec(). Remove the function too.
Fixes: 1289e96797bf ("sandbox: spi: Drop command-line SPI option") Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com> Reviewed-by: Simon Glass <sjg@chromium.org>
fdt: Use phandle to distinguish DT nodes with same name
While assigning the sequence number to subsystem instances by reading the
aliases property, only DT nodes names are compared and not the complete
path. This causes a problem when there are two DT nodes with same name but
have different paths.
In arch/arm/dts/k3-am65-main.dtsi there are two USB controllers with the
same device tree node name but different path. When aliases are defined for
these USB controllers then fdtdec_get_alias_seq() fails to pick the correct
instance for a given index.
fdt_path_offset() function is slow and this would effect the U-Boot
startup. To avert the time penalty on all boards, apply this extra check
only when required by using a config option.
Fix it by comparing the phandles of DT nodes after the node names match,
under a config option.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Fix whitespace error in Kconfig: Signed-off-by: Simon Glass <sjg@chromium.org>
Philipp Tomsich [Tue, 24 Nov 2020 17:14:52 +0000 (18:14 +0100)]
patman: Add --no-signoff to suppress adding signoffs
To enable use of patman with FSF/GNU projects, such as GCC or
Binutils, no Signed-off-by may be added. This adds a command
line flag '--no-signoff' to suppress adding signoffs in patman
when processing commits.
Signed-off-by: Philipp Tomsich <philipp.tomsich@vrull.eu> Reviewed-by: Simon Glass <sjg@chromium.org>
Fix patman testBranch() test: Signed-off-by: Simon Glass <sjg@chromium.org>
Sughosh Ganu [Mon, 14 Dec 2020 06:22:44 +0000 (11:52 +0530)]
fsp: Move and rename fsp_types.h file
The fsp_types.h header file contains macros for building signatures of
different widths. These signature macros are architecture agnostic,
and can be used in all places which use signatures in a data
structure. Move and rename the fsp_types.h under the common include
header.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tom Rini [Wed, 16 Dec 2020 00:06:03 +0000 (19:06 -0500)]
Travis-CI: Drop support
Travis-CI is changing their support for FOSS (understandably) to have a
limited per-month number of build minutes. Unfortunately for us, the
matrix of jobs we run will exhaust that very quickly. Remove the yml
file. Thanks for all the builds, Travis-CI!
Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Michael Walle [Sun, 20 Dec 2020 21:35:13 +0000 (22:35 +0100)]
board: kontron: sl28: reorder mmc devices
Since linux commit 2e6cde96873253fd9eb0f20afd8ffd18278cff75 ("arm64:
dts: ls1028a: make the eMMC and SD card controllers use fixed indices")
mmc0 is the eMMC and mmc1 is the SD card. Also swap it in u-boot to
avoid any confusion by the user and to be aligned with linux.
Tom Rini [Sun, 20 Dec 2020 19:55:59 +0000 (14:55 -0500)]
Merge tag 'efi-2021-01-rc4' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2021-01-rc4
* Provide a tool to create a file with UEFI variables to preseed UEFI
variable store.
* Make size of UEFI variable store configurable.
* Add man pages for commands 'bootefi' and 'button'.
projects / u-boot.git / log
