Joakim Tjernlund [Wed, 27 Nov 2019 18:35:10 +0000 (19:35 +0100)]
mpc85xx: ddr: Always start DDR RAM in Self Refresh mode
Some of t1042 boards fails DDR init with an Automatic calibration error
every now and then. Investigations revealed that true Warm boots
never failed. Warm boots has some extra steps performed, one being
to start DDRC in Self Refresh and then clearing SR right after.
Applying this SR method unconditionally made all our boards
stable again, regardless of Cold/Warm boot.
Tom Rini [Wed, 18 Dec 2019 12:20:19 +0000 (07:20 -0500)]
Merge branch 'next' of https://gitlab.denx.de/u-boot/custodians/u-boot-x86 into next
- Various x86 common codes updated for TPL/SPL
- I2C designware driver updated for PCI
- ICH SPI driver updated to support Apollo Lake
- Add Intel FSP2 base support
- Intel Apollo Lake platform specific drivers support
- Add a new board Google Chromebook Coral
Tom Rini [Tue, 17 Dec 2019 12:53:08 +0000 (07:53 -0500)]
Merge tag '20191217-for-next' of https://gitlab.denx.de/u-boot/custodians/u-boot-i2c into next
i2c: for next
- misc: i2c_eeprom:
Add partition support and add ability to query size
of eeprom device and partitions
- i2c common:
add support for offset overflow in to address and add
sandbox tests for it.
Robert Beckett [Mon, 28 Oct 2019 17:44:57 +0000 (17:44 +0000)]
i2c: add support for offset overflow in to address
Some devices (2 wire eeproms for example) use some bits from the chip
address to represent the high bits of the offset instead of or as well
as using multiple bytes for the offset, effectively stealing chip
addresses on the bus.
Add a chip offset mask that can be set for any i2c chip which gets
filled with the offset overflow during offset setup.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com> Signed-off-by: Ian Ray <ian.ray@ge.com> Reviewed-by: Heiko Schocher <hs@denx.de>
Simon Glass [Mon, 9 Dec 2019 00:40:20 +0000 (17:40 -0700)]
x86: Add chromebook_coral
Add support for coral which is a range of Apollo Lake-based Chromebook
released in 2017. This also includes reef released in 2016, since it is
based on the same SoC.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Mon, 9 Dec 2019 00:40:12 +0000 (17:40 -0700)]
spl: Add methods to find the position/size of next phase
Binman supports writing the position and size of U-Boot proper and SPL
into the previous phase of U-Boot. This allows the next phase to be easily
located and loaded.
Add functions to return these useful values, along with symbols to allow
TPL to load SPL.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Mon, 9 Dec 2019 00:40:09 +0000 (17:40 -0700)]
x86: apl: Add LPC driver
This driver the LPC and provides a few functions to set up LPC features.
These should probably use ioctls() or perhaps, better, have specific
uclass methods.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Mon, 9 Dec 2019 00:40:08 +0000 (17:40 -0700)]
x86: apl: Add ITSS driver
This driver models some sort of interrupt thingy but there are so many
abreviations that I cannot find out what it stands for. Possibly something
to do with interrupts.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 7 Dec 2019 04:42:58 +0000 (21:42 -0700)]
x86: apl: Add UART driver
Add a driver for the Apollo Lake UART. It uses the standard ns16550 device
but also sets up the input clock with LPSS and supports configuration via
of-platdata.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 7 Dec 2019 04:42:54 +0000 (21:42 -0700)]
x86: Add a generic Intel GPIO driver
Add a GPIO driver which uses the pinctrl driver to access the pad
information. This driver relies on the GPIO nodes being subnodes to the
pinctrl device.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 7 Dec 2019 04:42:53 +0000 (21:42 -0700)]
x86: Add a generic Intel pinctrl driver
Recent Intel SoCs share a pinctrl mechanism with many common elements. Add
an implementation of this core functionality, allowing SoC-specific
drivers to avoid adding common code.
As well as a pinctrl driver this provides a GPIO driver based on the same
code.
Once other SoCs use this driver we may consider moving more properties to
the device tree (e.g. the community info and pad definitions).
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 7 Dec 2019 04:42:50 +0000 (21:42 -0700)]
mtd: spi: Export spi_flash_std_probe()
With of-platdata we need to create drivers for particular chips, or at
least drivers that are separate from the standard code, since C structures
are created by dtoc which are private to that driver.
To avoid duplicating the probing code, export this probe function for use
by these drivers.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 7 Dec 2019 04:42:48 +0000 (21:42 -0700)]
spi: ich: Add TPL support
In TPL we want to reduce code size and support running with CONFIG_PCI
disabled. Add special code to handle this using a fixed BAR programmed
into the SPI on boot. Also cache the SPI flash to speed up boot.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 7 Dec 2019 04:42:42 +0000 (21:42 -0700)]
spi: ich: Add mmio_base to struct ich_spi_platdata
It is useful to store the mmio base in platdata. It reduces the amount of
casting needed. Update the code and move the struct to the C file at the
same time, as we will need to use with of-platdata.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 7 Dec 2019 04:42:41 +0000 (21:42 -0700)]
spi: ich: Various small tidy-ups
Use debug() instead of printf() to reduce code size and change a bool
return value to the use the 'bool' type. Also drop the global data
declaration since it not actually used. Finally, set the log category.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 7 Dec 2019 04:42:38 +0000 (21:42 -0700)]
spi: ich: Move the protection/lockdown code into a function
Reduce the size of the probe function but putting this code into its own
function.
Also remove the assumption that the PCH is always a parent of the SPI
controller, as this is not the case APL platforms. Use driver model to
find the PCH instead.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 7 Dec 2019 04:42:37 +0000 (21:42 -0700)]
spi: ich: Move init function just above probe()
It is annoying to have some of the init code in a different part of the
file. Move ich_init_controller() to just above probe() to keep things
together.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 7 Dec 2019 04:42:36 +0000 (21:42 -0700)]
x86: spi: Don't enable SPI_FLASH_BAR by default
We don't normally need this on x86 unless the size of SPI flash devices is
larger than 16MB. This can be enabled by particular SoCs as needed, since
it adds to code size.
Drop the default enabling of this option on x86.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 7 Dec 2019 04:42:33 +0000 (21:42 -0700)]
x86: Separate out U-Boot and device tree in ROM image
At present binman does not support updating a device tree that is part of
U-Boot (i.e u-boot.bin). Separate the entries into two so that we can get
updated entry information. This makes binman_entry_find() work correctly.
Do the same for SPL tool.
In both cases, group the two parts into a section so that SPL symbols get
the correct total size.
It may be possible for binman to handle this automatically at some point,
by ignoring u-boot.bin and always creating it from u-boot-nodtb.bin and
u-boot.dtb
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 7 Dec 2019 04:42:32 +0000 (21:42 -0700)]
x86: Don't repeat microcode in U-Boot if not needed
At present if SPL sets up the microcode then it is still included in
U-Boot as well. This is wasteful as microcode is large. Adjust the logic
in the image to prevent this.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 7 Dec 2019 04:42:31 +0000 (21:42 -0700)]
x86: Add an fdtmap and image-header
Add these entries to the ROM so that we can list the contents of an image
with 'binman ls'. The image-header is not essential but does speed up
access.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 7 Dec 2019 04:42:30 +0000 (21:42 -0700)]
x86: Add an option to control the position of SPL
For Apollo Lake SPL is run from CAR (cache-as-RAM) which is in a different
location from where SPL must be placed in ROM. In other words, although
SPL runs before SDRAM is set up, it is not execute-in-place (XIP).
Add a Kconfig option for the ROM position.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 7 Dec 2019 04:42:26 +0000 (21:42 -0700)]
x86: Disable microcode section for FSP2
At present we don't support loading microcode with FSP2. The correct way
to do this is by adding it to the FIT. For now, disable including
microcode in the image.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 7 Dec 2019 04:42:11 +0000 (21:42 -0700)]
x86: Set the DRAM banks to reflect real location
At present with fsp a single DRAM bank is added which extends to the
whole size of memory. However there is typically only 2GB of memory
available below the 4GB boundary, and this is what is used by U-Boot while
running in 32-bit mode.
Scan the tables to set the banks correct. The first bank is set to memory
below 4GB, and the rest of memory is put into subsequent banks.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 7 Dec 2019 04:42:10 +0000 (21:42 -0700)]
x86: Move fsp_prepare_mrc_cache() to fsp1 directory
This function needs to be different for FSP2, so move the existing
function into the fsp1 directory. Since it is only called from one file,
drop it from the header file.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 7 Dec 2019 04:42:05 +0000 (21:42 -0700)]
x86: Add a new global_data member for the cache record
At present we reuse the mrc_output char * to also point to the cache
record after it has been set up. This is confusing and doesn't save much
data space.
Add a new mrc_cache member instead.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 7 Dec 2019 04:42:03 +0000 (21:42 -0700)]
x86: Adjust mrccache_get_region() to use livetree
Change the algorithm to first find the flash device then read the
properties using the livetree API. With this change the device is not
probed so this needs to be done in mrccache_save().
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This should take account of the end of the new cache record since a record
cannot extend beyond the end of the flash region. This problem was not
seen before due to the alignment of the relatively small amount of MRC
data.
But with Apollo Lake the MRC data is about 45KB, even if most of it is
zeroes.
Fix this bug and update the parameter name to be less confusing.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
projects / u-boot.git / log
