Marcel Ziswiler [Fri, 8 Feb 2019 17:12:17 +0000 (18:12 +0100)]
apalis_imx6: add distroboot support
Add support for distro boot. This is especially helpful for external
devices. There is a global boot command which scans a predefined
list of boot targets:
run distro_bootcmd
As well as direct boot commands such as:
run bootcmd_mmc1
run bootcmd_mmc2
run bootcmd_usb
run bootcmd_dhcp
...
Refer to doc/README.distro for details.
While at it, remove the CONFIG_DRIVE_TYPES define which has not
been used and was meant to be used for multi device boot support
which is now provided by distroboot.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Marcel Ziswiler [Fri, 8 Feb 2019 17:12:10 +0000 (18:12 +0100)]
apalis_imx6: clean-up and migrate gpios to using driver model
Migrate GPIOs to using driver model, properly request backlight,
Ethernet PHY reset, MMC/SD card detect and USB power GPIOs and also
enable SION bit in pin muxing for Apalis, backlight, eMMC reset,
Ethernet PHY reset and USB power enable GPIOs.
While at it also update copyright year, clean-up/re-order includes,
add some comments clarifying ifdef scope and do some White-space
clean-up.
Lukasz Majewski [Wed, 13 Feb 2019 21:46:48 +0000 (22:46 +0100)]
ARM: DTS: Update pcm052 based dts files (bk4r1/pcm052)
This commit provides update and renames the bk4r1.dts to vf610-bk4r1.dts
file with more on SoC HW description.
The pcm052.dts has been renamed to vf610-pcm052.dts as well.
Moreover, a new vf610-pcm052.drsi file has been introduced
to reuse the common code between devices based on Phytec's
pcm052 modules.
Ported from Linux kernel - v4.20 (tag)
Lukasz Majewski [Wed, 13 Feb 2019 21:46:41 +0000 (22:46 +0100)]
vybrid: clock: Provide enable_i2c_clk() function for Vybrid
Provide function to enable I2C clocks for vf610 - in the generic code.
This function overrides the default weak function implementation (which
only returns 1).
Tom Rini [Fri, 12 Apr 2019 16:34:44 +0000 (12:34 -0400)]
Merge git://git.denx.de/u-boot-marvell
- Misc dts files sync'ed with Linux version (Chris)
- Orion watchdog fix (Chris)
- kwbimage changed to also support Marvell bin_hdr binary (Chris)
- Add DM support to enable CONFIG_BLK for sata_mv (Stefan)
- Enable BLK on multiple platforms (Stefan)
- Misc minor fixes to AXP theadorable board (Stefan)
- Correct logic for DM_SCSI + unconverted drivers check (stefan)
- Misc changes to kirkwood to enable DM_USB here (Chris)
- Change ahci_mvebu to enable usage on A38x (Baruch)
- Update the kirkwood entry in git-mailrc (Baruch)
- Misc minor improvements (turris, documentation) (Baruch)
- Enhance sata_mv to support Kirkwood as well (Michael)
- Add wdt command (Michael)
- Add Marvell integrated CPUs (MSYS) support with DB-XC3-24G4XG
board support (Chris)
Tom Rini [Fri, 12 Apr 2019 16:22:43 +0000 (12:22 -0400)]
Merge branch '2019-04-11-ti-master-imports'
- Improve Keystone 3 SoC support (DMA, TI SCI)
- Improve Keystone 2 SoC support (PHY fixes on various platforms)
- Improve am335x families (new platforms, more boot mode options in SPL
via DM).
- General DaVinci, OMAP5 fixes.
The driver adds the support for the STMicroelectronics FMC2 NAND
Controller found on STM32MP SOCs.
This patch adds the polling mode, a basic mode that do not need
any DMA channels.
Only NAND_ECC_HW mode is actually supported.
The driver supports a maximum 8k page size.
The following ECC strength and step size are currently supported:
- nand-ecc-strength = <8>, nand-ecc-step-size = <512> (BCH8)
- nand-ecc-strength = <4>, nand-ecc-step-size = <512> (BCH4)
- nand-ecc-strength = <1>, nand-ecc-step-size = <512> (Extended ECC
based on Hamming)
This patch has been tested on Micron MT29F8G08ABACAH4.
We are facing issues in the driver since SPI NOR framework has moved
on SPI MEM framework, and SPI NAND framework is not running properly
with the current driver.
To be able to solve issues met on SPI NOR Flashes and to be able to
support SPI NAND Flashes, the driver has been reworked. We are now using
exec_op ops instead of using xfer ops.
Thanks to this rework, the driver has been successfully tested with:
- mx66l51235l SPI NOR Flash on stm32f746 SOC
- n25q128a SPI NOR Flash on stm32f769 SOC
- mx66l51235l SPI NOR Flash on stm32mp1 SOC
- mt29f2g01abagd SPI NAND Flash on stm32mp1 SOC
Signed-off-by: Christophe Kerello <christophe.kerello@st.com> Tested-by: Patrick DELAUNAY <patrick.delaunay@st.com> Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Patrick Delaunay [Fri, 12 Apr 2019 12:38:28 +0000 (14:38 +0200)]
ARM: dts: Add STMFX gpio expander support for stm32mp157c-ev1
Adds alias to set the pincontrol seq id.
For STMFX gpio expander, force sequence number after
the last bank (GPIOZ) to avoid conflict between STM32MP and STMFX
gpio bank sequence number.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Patrick Delaunay [Mon, 11 Mar 2019 10:13:16 +0000 (11:13 +0100)]
config: stm32mp15: Enable STMFX support
Activate PINCTRL_STMFX and needed part for generic pincontrol
PINCTRL_FULL, PINCONF. Increase pre-reloc memory for MALLOC
(needed for each DM pinconfig node).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This patch adds pinctrl/GPIO driver for STMicroelectronics
Multi-Function eXpander (STMFX) GPIO expander.
STMFX is an I2C slave controller, offering up to 24 GPIOs.
The driver relies on UCLASS_PINCTRL and UCLASS_GPIO.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Patrice Chotard [Tue, 12 Feb 2019 15:50:40 +0000 (16:50 +0100)]
Board: stm32mp1: Add supply current boot information
For DK1/DK2 boards, check if power supply provides enough current
to allow the board to boot correctly.
ADC@0 channel 18 and 19 are connected to USB type-C CC1 and CC2
signals. The table below shows the behavior for different range of
CC1 or CC2:
range | power supply | red led | console message
(Volts) | (Amps) | blinks |
--------------|--------------|---------|-----------------------------------
[2.10 - 1.23[ | 3 | NO | NO
[1.23 - 0.66[ | 1.5 | 3 times | WARNING 1.5A power supply detected
[0.66 - 0] | 0.5 | 2 times | WARNING 500mA power supply detected
If detected current is < 3A, red led is kept ON after blinking.
Patrice Chotard [Tue, 12 Feb 2019 15:50:38 +0000 (16:50 +0100)]
ARM: dts: stm32: Synchronize DT with kernel one
This patch synchronizes U-boot DT with kernel one
This is based on https://patchwork.kernel.org/cover/10797115/
This patch adds initial support of STM32MP157 discovery boards:
- Add support of stm32mp157a discovery1 board (part number: STM32MP157A-DK1).
This board embeds a STM32MP157a SOC with AC package (TFBGA361, 148 ios)
and 512MB of DDR3. Several connections are available on this boards:
4*USB2.0, 1*USB2.0 typeC, SDcard, RJ45, HDMI, Arduino connector, ...
- Add support of stm32mp157c discovery2 board (part number: STM32MP157C-DK2).
This board is a "super-set" of stm32mp157a-dk1. A display panel (otm8009a)
and Murata wifi/BT combo is added.
Add functions to read/update the non volatile memory of STPMIC1
(8 bytes-register at 0xF8 address) and allow access
with fuse command (bank=1, word > 0xF8).
Patrick Delaunay [Fri, 12 Apr 2019 09:55:46 +0000 (11:55 +0200)]
stm32mp1: add command poweroff
Activate the command poweroff by default for STM32MP1:
- with PCSI from TF-A for trusted boot
- with PMIC sysreset request for basic boot (SYSRESET_POWER)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Alignment with STPMIC1 datasheet
s/MAIN_CONTROL_REG/MAIN_CR/g
s/MASK_RESET_BUCK/BUCKS_MRST_CR/g
s/MASK_RESET_LDOS/LDOS_MRST_CR/g
s/BUCKX_CTRL_REG/BUCKX_MAIN_CR/g
s/VREF_CTRL_REG/REFDDR_MAIN_CR/g
s/LDOX_CTRL_REG/LDOX_MAIN_CR/g
s/USB_CTRL_REG/BST_SW_CR/g
s/STPMIC1_NVM_USER_STATUS_REG/STPMIC1_NVM_SR/g
s/STPMIC1_NVM_USER_CONTROL_REG/STPMIC1_NVM_CR/g
and update all the associated defines.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
SW impact for Rev 1.2 of STPMIC1 in U-Boot:
Buck converters output voltage change for Buck1
=> Vdd min 0,725 to max 1,5V instead of 0.6V to 1.35V
(see STPMIC1 datasheet / chapter 5.3 Buck converters)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrick Delaunay [Wed, 27 Feb 2019 16:01:24 +0000 (17:01 +0100)]
stm32mp1: add syscfg initialization
Initialize the system configuration for basic boot
- update interconnect setting
- disable pull-down for boot pin
- enable High Speed Low Voltage Pad mode for SPI, SDMMC, ETH, QSPI
- activate I/O compensation
Done by SSBL = TF-A for trusted boot
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrick Delaunay [Wed, 27 Feb 2019 16:01:21 +0000 (17:01 +0100)]
stm32mp1: update memory layout
Update the memory layout to be aligned with other platform and avoid
overlap with 32MB Linux kernel (multiv7 image).
+ Kernel => 32MiB offset = 0xC2000000
and increase the bootm size to 32MiB
+ FDT => 64MiB offset = 0xc4000000
+ SCRIPT => 65Mib offset = 0xc4100000
+ PXESCRIPT => 66Mib offset = 0xc4200000
+ SPLASHIMAGE => 67Mib offset = 0xc4300000
+ RAMDISK => 68Mib offset = 0xc4400000
(not limited size)
In sources/boot/u-boot/doc/README.distro
+ kernel_addr_r: A size of 16MB for the kernel is likely adequate.
+ pxefile_addr_r: A size of 1MB for extlinux.conf is more than adequate.
+ fdt_addr_r: A size of 1MB for the FDT/DTB seems reasonable.
+ ramdisk_addr_r: It is recommended that this location be highest in RAM
out of fdt_addr_, kernel_addr_r, and ramdisk_addr_r,
so that the RAM disk can vary in size and use any
available RAM.
+ pxefile_addr_r: A size of 1MB for extlinux.conf is more than adequate.
+ scriptaddr: A size of 1MB for extlinux.conf is more than adequate.
For suggestions on memory locations for ARM systems, you must follow
the guidelines specified in Documentation/arm/Booting
in the Linux kernel tree.
And in sources/linux-stm32mp/Documentation/arm/Booting
The zImage may also be placed in system RAM and called there. The
kernel should be placed in the first 128MiB of RAM. It is recommended
that it is loaded above 32MiB in order to avoid the need to relocate
prior to decompression, which will make the boot process slightly
faster.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrick Delaunay [Wed, 27 Feb 2019 16:01:15 +0000 (17:01 +0100)]
stm32mp1: cosmetic cleanup Kconfig
Cosmetic cleanup in mach-stm32mp Kconfig
- remove duplicated SPL_DRIVERS_MISC_SUPPORT
- update help for TARGET_STM32MP1
- set value for NR_DRAM_BANKS
- remove one comment as DEBUG_UART is deactivated by default
- include board Kconfig at the end of the file
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrick Delaunay [Wed, 27 Feb 2019 16:01:12 +0000 (17:01 +0100)]
stm32mp1: update boot mode management
- export the function get_bootmode() and reused it in spl code
- manage uart instance by alias (prepare v4.19 binding)
- solve issue on nand instance
- restore console for uart boot
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrick Delaunay [Tue, 12 Feb 2019 10:44:41 +0000 (11:44 +0100)]
stm32mp1: display board information
Implement checkboard() function to display
- the boot chain used: basic or trusted
- the board compatible in device tree
- the board identifier and revision, saved in OTP59 for ST boards
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Faiz Abbas [Fri, 5 Apr 2019 08:48:46 +0000 (14:18 +0530)]
mmc: omap_hsmmc: Set 3.3V for IO voltage
Pbias voltage should match the IO voltage set for the SD card. With the
latest pbias change to 3.3V, update the capabilities and IO voltages
settings to 3.3V.
Tom Rini [Tue, 19 Mar 2019 11:14:37 +0000 (07:14 -0400)]
ti: keystone2: Move CONFIG_ISW_ENTRY_ADDR to a common place
The ISW_ENTRY_ADDR Kconfig option under mach-omap2 isn't a SoC specific
notion but rather "where is our previous stage loaded in memory?"
option. Make use of this on ARCH_KEYSTONE rather than SPL_TEXT_BASE for
our HS builds that are not using SPL anyhow.
Cc: Vitaly Andrianov <vitalya@ti.com> Cc: Andrew F. Davis <afd@ti.com> Cc: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com?
projects / u-boot.git / log
