Pali Rohár [Wed, 2 Mar 2022 10:49:18 +0000 (11:49 +0100)]
tools: kwboot: Check for return value of kwboot_tty_send() and tcflush()
Failure of kwboot_tty_send() and tcflush() functions is fatal, it does not
make sense to continue. So return error back to the caller like in other
places where are called these functions.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Stefan Roese <sr@denx.de>
Chris Packham [Tue, 1 Mar 2022 00:53:23 +0000 (13:53 +1300)]
ARM: mvebu: x530: clearfog: Add ODT configuration
Commit 369e532691e0 ("ddr: marvell: a38x: allow board specific ODT
configuration") added the odt_config member to struct
mv_ddr_topology_map ahead of the clk_enable and ck_delay members. This
means that any boards that configured either of clk_enable or ck_delay
needed to have their board topology updated. This affects the x530 and
clearfog boards. Other A38x boards don't touch any of the trailing
members of mv_ddr_topology_map so don't need updating.
Fixes: 369e532691e0 ("ddr: marvell: a38x: allow board specific ODT configuration") Signed-off-by: Chris Packham <judge.packham@gmail.com> Acked-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Stefan Roese <sr@denx.de>
Marek Behún [Mon, 28 Feb 2022 14:59:37 +0000 (15:59 +0100)]
arm64: a37xx: pinctrl: Fix PWM pins indexes
Commit 5534fb4f4833 ("arm64: a37xx: pinctrl: Correct PWM pins
definitions") introduced bogus definitions os PWM pins: all 4 pins have
index 11, instead of having indexes 11, 12, 13, 14.
Fix this.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Wed, 23 Feb 2022 12:52:32 +0000 (13:52 +0100)]
arm: a37xx: pci: Fix a3700_fdt_fix_pcie_regions() function again
The a3700_fdt_fix_pcie_regions() function still computes nonsense.
It computes the fixup offset from the PCI address taken from the first
row of the "ranges" array, which means that:
- PCI address must equal CPU address (otherwise the computed fix offset
will be wrong),
- the first row must contain the lowest address.
This is the case for the default device-tree, which is why we didn't
notice it.
It also adds the fixup offset to all PCI and CPU addresses, which is
wrong.
Instead:
1) The fixup offset must be computed from the CPU address, not PCI
address.
2) The fixup offset must be computed from the row containing the lowest
CPU address, which is not necessarily contained in the first row.
3) The PCI address - the address to which the PCIe controller remaps the
address space as seen from the point of view of the PCIe device -
must be fixed by the fix offset in the same way as the CPU address
only in the special case when the CPU adn PCI addresses are the same.
Same addresses means that remapping is disabled, and thus if we
change the CPU address, we need also to change the PCI address so
that the remapping is still disabled afterwards.
Now it will take the lowest CPU address, which is in second row, E9000000, and compute the fix offset F2000000 - E9000000 = 09000000,
and then add it to all CPU addresses and those PCI addresses which
equal to their corresponding CPU addresses, resulting in
PCI address CPU address 70000000F3000000 F2000000F2000000 F4000000F4000000
where all of the CPU addresses are in the needed window.
Fixes: 4a82fca8e330 ("arm: a37xx: pci: Fix a3700_fdt_fix_pcie_regions() function") Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Fri, 18 Feb 2022 11:25:23 +0000 (12:25 +0100)]
pci: pci_mvebu: Cleanup macro names
Use "MVPCIE_" prefix instead of generic "PCIE_" prefix for pci_mvebu.c
specific macros. Define offset macros for Root Port registers and use
standard register macros from pci.h when accessing Root Port registers.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
Linus Walleij [Sun, 20 Feb 2022 22:47:01 +0000 (23:47 +0100)]
board: stemmy: Detect board variants and patch DTB
This patch scans the cmdline from the Samsung SBL (second stage
bootloader) and stores the parameters board_id=N and lcdtype=N
in order to augment the DTB for different board and LCD types.
We then add a custom ft_board_setup() callback that will inspect
the DTB and patch it using the stored LCD type. At this point
we know which product we are dealing with, so using the passed
board_id we can also print the board variant for diagnostics.
We patch the Codina, Skomer and Kyle DTBs to use the right
LCD type as passed in lcdtype from the SBL.
This also creates an infrastructure for handling any other
Samsung U8500 board variants that may need a slightly augmented
DTB.
Janne Grunau [Sat, 19 Feb 2022 13:05:19 +0000 (14:05 +0100)]
arm: apple: Switch to fully dynamic mem layout
Support for Apple M1 Pro and Max will allow using a single binary for
all M1 SoCs. The M1 Pro/Max have a different memory layout. The RAM
start address is 0x100_0000_0000 instead of 0x8_0000_0000.
Replace the hardcoded memory layout with dynamic initialized
environment variables in board_late_init().
Tested on Mac Mini (2020) and Macbook Pro 14-inch (2021).
Signed-off-by: Janne Grunau <j@jannau.net> Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Felix Brack [Mon, 21 Feb 2022 13:26:05 +0000 (14:26 +0100)]
arm: pdu001: Setup pinmux for console UART as early as possible
To make sure we get a working console as soon as possible in the SPL the
UART pins require to be configured earlier. This is especially
true for the pins of UART3, since the PDU001 board uses this UART for
the console by default.
Felix Brack [Tue, 15 Feb 2022 14:27:23 +0000 (15:27 +0100)]
arm: pdu001: Fix early debugging UART
The changes from commit 0dba45864b2a ("arm: Init the debug UART")
prevent the early debug UART from being initialized correctly.
To fix this we not just configure the pin multiplexer but add setting up
early clocks.
Signed-off-by: Felix Brack <fb@ltec.ch> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Pali Rohár [Sun, 13 Feb 2022 00:09:46 +0000 (01:09 +0100)]
tools: mkimage/dumpimage: Allow to use -l with -T
Currently -l option for mkimage and dumpimage ignores option -T and always
tries to autodetect image type.
With this change it is possible to tell mkimage and dumpimage to parse
image file as specific type (and not random autodetected type). This allows
to use mkimage -l or dumpimage -l as tool for validating image.
params.type for -l option is now by default initialized to zero
(IH_TYPE_INVALID) instead of IH_TYPE_KERNEL. imagetool_get_type() for
IH_TYPE_INVALID returns NULL, which is assigned to tparams. mkimage and
dumpimage code is extended to handle tparams with NULL for -l option. And
imagetool_verify_print_header() is extended to do validation via tparams if
is not NULL.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Hou Zhiqiang [Thu, 17 Feb 2022 03:51:36 +0000 (11:51 +0800)]
tools: pblimage: fix image header verification function
The Layerscape platforms have different RCW header value from FSL
PowerPC platforms, the current image header verification callback
is only working on PowerPC, it will fail on Layerscape, this patch
is to fix this issue.
This is a historical problem and exposed by the following patch:
http://patchwork.ozlabs.org/project/uboot/patch/20220114173443.9877-1-pali@kernel.org
Daniel Klauer [Wed, 9 Feb 2022 14:53:41 +0000 (15:53 +0100)]
lx2160a: Fix distroboot device list for configs without USB/SCSI/etc
The BOOT_TARGET_DEVICES list for distro_bootcmd was hard-coded to assume
that all boot devices are available/enabled in the configuration,
thus ignoring the actual config settings. The config_distro_bootcmd.h
header file specifically has compile-time checks to detect such problems.
To allow disabling USB, SCSI, etc. in custom lx2160a board configs,
make it depend on the config settings and use only the enabled features.
Signed-off-by: Daniel Klauer <daniel.klauer@gin.de> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Michael Walle [Fri, 25 Feb 2022 12:48:40 +0000 (18:18 +0530)]
board: sl28: disable random MAC address generation
Nowadays, u-boot (when CONFIG_NET_RANDOM_ETHADDR is set) will set
enetaddr to a random value if not set and then pass the randomly
generated MAC address to linux.
This is bad for the following reasons:
(1) it makes it impossible for linux to detect this error
(2) linux won't trigger any fallback mechanism for the case where
it didn't find any valid MAC address
(3) a saveenv will store this randomly generated MAC address in the
environment
Probably, the user will also be unaware that something is wrong. He will
just get different MAC addresses on each reboot, asking himself why this
is the case.
As this board usually have a serial port, the user can just fix this by
setting the MAC address manually in the environment. Also disable the
netconsole just in case, because it cannot be guaranteed that it will
work in any case. After all, this was just a convenience option, because
the bootloader - right now - doesn't have the ability to read the MAC
address, which is stored in the OTP. But it is far more important to
have a clear view of whats wrong with a board and that means we can no
longer use this Kconfig option.
Signed-off-by: Michael Walle <michael@walle.cc>
[Rebased] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Michael Walle [Mon, 15 Nov 2021 22:45:49 +0000 (23:45 +0100)]
board: sl28: disable recovery watchdog
This board has an internal watchdog which supervises the board startup.
Although, the initial state of the watchdog is configurable, it is
enabled by default. In board_late_init(), which means almost everything
worked as expected, disable the watchdog.
Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Michael Walle [Fri, 25 Feb 2022 12:40:24 +0000 (18:10 +0530)]
gpio: add sl28cpld driver
The gpio block is part of the sl28cpld sl28cpld management controller.
There are three different flavors: the usual input and output where the
direction is configurable, but also input only and output only variants.
Signed-off-by: Michael Walle <michael@walle.cc>
[Rebased] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Michael Walle [Mon, 15 Nov 2021 22:45:43 +0000 (23:45 +0100)]
watchdog: add sl28cpld watchdog driver
The watchdog timer is part of the sl28cpld management controller. The
watchdog timer usually supervises the bootloader boot-up and if it bites
the failsafe bootloader will be activated. Apart from that it supports
the usual board level reset and one SMARC speciality: driving the
WDT_TIMEOUT# signal.
Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Masahisa Kojima [Tue, 22 Feb 2022 00:58:30 +0000 (09:58 +0900)]
efi_loader: update the timing of enabling and disabling EFI watchdog
UEFI specification requires that 5 minutes watchdog timer is
armed before the firmware's boot manager invokes an EFI boot option.
This watchdog timer is updated as follows, according to the
UEFI specification.
1) The EFI Image may reset or disable the watchdog timer as needed.
2) If control is returned to the firmware's boot manager,
the watchdog timer must be disabled.
3) On successful completion of EFI_BOOT_SERVICES.ExitBootServices()
the watchdog timer is disabled.
1) is up to the EFI image, and 3) is already implemented in U-Boot.
This patch implements 2), the watchdog is disabled when control is
returned to U-Boot.
In addition, current implementation arms the EFI watchdog at only
the first "bootefi" invocation. The EFI watchdog must be armed
in every EFI boot option invocation.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org> Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Masami Hiramatsu [Wed, 16 Feb 2022 06:16:12 +0000 (15:16 +0900)]
efi_loader: test/py: Reset system after capsule update on disk
Add a cold reset soon after processing capsule update on disk.
This is required in UEFI specification 2.9 Section 8.5.5
"Delivery of Capsules via file on Mass Storage device" as;
In all cases that a capsule is identified for processing the system is
restarted after capsule processing is completed.
This also reports the result of each capsule update so that the user can
notice that the capsule update has been succeeded or not from console log.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org> Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Masami Hiramatsu [Wed, 16 Feb 2022 06:16:02 +0000 (15:16 +0900)]
test/py: Handle expected reboot while booting sandbox
Add expected_reset optional argument to ConsoleBase::ensure_spawned(),
ConsoleBase::restart_uboot() and ConsoleSandbox::restart_uboot_with_flags()
so that it can handle a reset while the 1st boot process after main
boot logo before prompt correctly.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org> Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Masami Hiramatsu [Wed, 16 Feb 2022 06:15:42 +0000 (15:15 +0900)]
efi_loader: use efi_update_capsule_firmware() for capsule on disk
Since the efi_update_capsule() represents the UpdateCapsule() runtime
service, it has to handle the capsule flags and update ESRT. However
the capsule-on-disk doesn't need to care about such things.
Thus, the capsule-on-disk should use the efi_capsule_update_firmware()
directly instead of calling efi_update_capsule().
This means the roles of the efi_update_capsule() and capsule-on-disk
are different. We have to keep the efi_update_capsule() for providing
runtime service API at boot time.
Ilias Apalodimas [Mon, 14 Feb 2022 09:14:22 +0000 (11:14 +0200)]
efi_loader: fix uefi secure boot with intermediate certs
The general rule of accepting or rejecting an image is
1. Is the sha256 of the image in dbx
2. Is the image signed with a certificate that's found in db and
not in dbx
3. The image carries a cert which is signed by a cert in db (and
not in dbx) and the image can be verified against the former
4. Is the sha256 of the image in db
For example SHIM is signed by "CN=Microsoft Windows UEFI Driver Publisher",
which is issued by "CN=Microsoft Corporation UEFI CA 2011", which in it's
turn is issued by "CN=Microsoft Corporation Third Party Marketplace Root".
The latter is a self-signed CA certificate and with our current implementation
allows shim to execute if we insert it in db.
However it's the CA cert in the middle of the chain which usually ends up
in the system's db. pkcs7_verify_one() might or might not return the root
certificate for a given chain. But when verifying executables in UEFI, the
trust anchor can be in the middle of the chain, as long as that certificate
is present in db. Currently we only allow this check on self-signed
certificates, so let's remove that check and allow all certs to try a
match an entry in db.
Open questions:
- Does this break any aspect of variable authentication since
efi_signature_verify() is used on those as well?
The wrong phy was being enabled, because it worked and the proper
PHY did not. After the Renesas maintainer made some adjustments
to the device tree, Linux was able to use the proper driver, and
when that device tree was ported to Linux, the ethernet stopped
working due to the lack of rgmii-rxid support. Now that
rgmii-rxid is supported, enable the proper driver to restore
ethernet function.
Fixes: 1eaf61c84db6 ("arm: dts: beacon-rzg2: Resync device trees with Linux 5.16-rc3") Signed-off-by: Adam Ford <aford173@gmail.com>
Adam Ford [Fri, 25 Feb 2022 20:32:52 +0000 (14:32 -0600)]
net: ravb: Add tx/rx delay flag checks and support for rgmii-rxid
Some boards like the Beacon RZ/G2 SOM use either flags for
tx-internal-delay-ps, rx-internal-delay-ps or rgmii-rxid.
In Linux the APSR_RDM flag is set when either rx-internal-delay-ps
is set or the mode is rgmii-rxid, and the APSR_TDM is set when
tx-internal-delay-ps is found or rgmii-txid is set, and both
are set if rgmii-id is set.
The ravb driver in U-Boot driver was missing rgmii-rxid support,
so add that support in a similar fashion to what is done in Linux.
Philippe Reynes [Tue, 22 Feb 2022 13:54:39 +0000 (14:54 +0100)]
scripts: Makefile.lib: generate dsdt_generated.c instead of dsdt.c
There is a conflict between the static file
lib/acpi/dsdt.c and the file dsdt.c generated
dynamicaly by scripts/Makefile.lib. When a
mrproper is done, the static file dsdt.c is
removed. If a build with acpi enabled is
launched after, the following error is raised:
CC lib/acpi/acpi_table.o
make[2]: *** No rule to make target 'lib/acpi/dsdt.asl', needed by 'lib/acpi/dsdt.c'. Stop.
scripts/Makefile.build:394: recipe for target 'lib/acpi' failed
To avoid such error, the generated file is named
dsdt_generated.c instead of dstdt.c.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com> Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Patrick Delaunay [Mon, 31 Jan 2022 16:21:38 +0000 (17:21 +0100)]
cmd: clk: replace clk_lookup by uclass_get_device_by_name
The function clk_lookup can be replaced by a direct call
to uclass_get_device_by_name for UCLASS_CLK.
This patch removes duplicated codes by the generic DM API and avoids
issue in clk_lookup because result of uclass_get_device wasn't tested;
when ret < 0, dev = NULL and dev->name is invalid, the next function
call strcmp(name, dev->name) causes a crash.
Patrick Delaunay [Mon, 24 Jan 2022 13:17:14 +0000 (14:17 +0100)]
clk: ccf: correct the test on the parent uclass in clk_enable/clk_disable
It is safe to check if the uclass id on the device is UCLASS_CLK
before to call the clk_ functions, but today this comparison is
not done on the device used in API: clkp->dev->parent
but on the device himself: clkp->dev.
This patch corrects this behavior and tests if the parent device
is a clock device before to call the clock API, clk_enable or
clk_disable, on this device.
Fixes: 0520be0f67e3 ("clk: prograte clk enable/disable to parent") Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Sean Anderson <seanga2@gmail.com>
Sean Anderson [Sat, 15 Jan 2022 20:52:47 +0000 (15:52 -0500)]
clk: Add clk_get_by_name_optional
This adds a helper function for clk_get_by_name in cases where the clock is
optional. Hopefully this helps point driver writers in the right direction.
Also convert some existing users.
Sean Anderson [Wed, 22 Dec 2021 17:11:13 +0000 (12:11 -0500)]
clk: Add driver API to HTML docs
This converts the existing driver API docs (clk-uclass.h) to kernel doc
format and adds them to the HTML documentation. Because the kernel doc
sphinx converter does not handle functions in structs very well, the
individual methods are documented separately. This is primarily inspired by
the phylink documentation [1], which uses this trick extensively.
Sean Anderson [Wed, 22 Dec 2021 17:11:12 +0000 (12:11 -0500)]
clk: Add client API to HTML docs
This converts the existing client (aka clk.h) documentation to kernel doc
format, and adds it to the HTML docs. I have tried to preserve existing
comments as much as possible, refraining from semantic changes.
Signed-off-by: Sean Anderson <seanga2@gmail.com> Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Link: https://lore.kernel.org/r/20211222171114.3091780-4-seanga2@gmail.com
[rebased onto u-boot/master and resolved conflicts] Signed-off-by: Sean Anderson <seanga2@gmail.com>
Sean Anderson [Wed, 22 Dec 2021 17:11:11 +0000 (12:11 -0500)]
clk: Inline clk_get_*_optional
The optional varients of clk_get_* functions are just simple wrappers.
Reduce code size a bit by inlining them. On platforms where it is not used
(most of them), it will not be compiled in any more. On platforms where
they are used, the inlined branch should not cause any significant growth.
Adam Ford [Sat, 19 Feb 2022 23:08:46 +0000 (17:08 -0600)]
usb: ehci-omap: Remove OMAP_EHCI_PHYx_RESET_GPIO from Kconfig
With the omap-ehci driver now using the phy subsystem to enable
and disable reset, the driver no longer needs to know which
GPIO's are used, and they can be removed from Kconfig.
Adam Ford [Sat, 19 Feb 2022 23:08:45 +0000 (17:08 -0600)]
usb: ehci-omap: Use PHY system to manage phy resets
There are a few boards that use hard-coded GPIO definitions in
their respective defconfig files. If the GPIO's are listed
in their device trees, the nop-phy can toggle the GPIO's,
so the EHCI driver does not need to know anything about the
GPIO's. Add functions for getting the phys and remove the GPIO
toggles since the phy will now do that.
Adam Ford [Sat, 19 Feb 2022 23:08:44 +0000 (17:08 -0600)]
usb: ehci-omap: Make Kconfig select PHY if USB_EHCI_OMAP
The USB_EHCI_OMAP driver currently has a series of Kconfig options
which let users specify a GPIO for the reset pin. Some devices
may have only one reset, while others might have more.
Since there is a nop phy driver, let's selct enable the PHY
system, and imply the nop phy driver. The nop phy driver can now
toggle the reset pins when putting the phy in and out of reset.
If the gpio is listed under the phy, it will get toggled and
the hard-coded config options specifying the GPIO numbers can
eventually go away.
Adam Ford [Sat, 19 Feb 2022 23:08:43 +0000 (17:08 -0600)]
phy: nop-phy: Fix enabling reset
The reset function should place the phy into reset, while the
init function should take the phy out of reset. Currently the
reset function takes it out of reset, and the init calls the
reset.
Adam Ford [Sat, 19 Feb 2022 23:08:42 +0000 (17:08 -0600)]
usb: ehci-omap: Move omap_ehci_hcd_init to omap_ehci_probe
The OMAP3 hierarchy has the ehci node as a sub-node of the
usbhshost. The usbhshost node contains an ohci and an ehci
subnode. The configuration of the ehci belongs in the
EHCI node and not its parent. Move it to the proper probe.
usb start
starting USB...
Bus ehci@48064800: USB EHCI 1.00
Bus usb_otg_hs@480ab000: Port not available.
scanning bus ehci@48064800 for devices... 3 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Adam Ford [Sat, 19 Feb 2022 23:08:41 +0000 (17:08 -0600)]
usb: ehci-omap: Drop dead code
omap_ehci_hcd_stop appears to be dead code, and omap_ehci_hcd_init
is only called by the probe function, so it can be static to that
function. Remove both from the header along with some additional
checking for DM_USB.
On some configs (like stm32mp15_dhcom_basic_defconfig), if configs
SPL_LOAD_FIT_FULL and SPL_FIT_FULL_CHECK are enabled. Then the compilatio
fails with the following error:
arm-linux-gnueabi-ld.bfd: boot/image-fit.o: in function `fit_check_format':
<PATH>/uboot/u-boot-stm/boot/image-fit.c:1641: undefined reference to `fdt_check_full'
scripts/Makefile.spl:509: recipe for target 'spl/u-boot-spl' failed
This issue happens because the function fdt_check_full is only defined if
"!defined(FDT_ASSUME_MASK) || FDT_ASSUME_MASK != 0xff". But this function
may be called even if this condition are not verified. To avoid this issue,
the function fdt_check_full is always defined.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 8 Feb 2022 18:50:00 +0000 (11:50 -0700)]
binman: Move entry-data collection into a Entry method
Collecting the data from a list of entries and putting it in a file is
a useful operation that will be needed by other entry types. Put this into
a method in the Entry class.
Add some documentation about how to collect data for an entry type.
Simon Glass [Tue, 8 Feb 2022 18:49:58 +0000 (11:49 -0700)]
binman: Support a list of strings with the mkimage etype
At present the 'args' property of the mkimage entry type is a string. This
makes it difficult to include CONFIG options in that property. In
particular, this does not work:
args = "-n CONFIG_SYS_SOC -E"
since the preprocessor does not operate within strings, nor does this:
args = "-n" CONFIG_SYS_SOC" "-E"
since the device tree compiler does not understand string concatenation.
Roger Quadros [Sat, 19 Feb 2022 18:50:04 +0000 (20:50 +0200)]
binman: Add support for TEE BL32
Add an entry for OP-TEE Trusted OS 'BL32' payload.
This is required by platforms using Cortex-A cores with TrustZone
technology.
Signed-off-by: Roger Quadros <rogerq@kernel.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Add missing-blob-help, renumber the test file, update entry-docs: Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 8 Feb 2022 18:49:52 +0000 (11:49 -0700)]
dtoc: Allow deleting nodes and adding them in the same sync
This does not work at present, since the current algorithm assumes that
either there are no nodes or all nodes have an offset. If a node is new,
but an old node is still in the tree, then syncing fails due to this
assumption.
Simon Glass [Tue, 8 Feb 2022 18:49:47 +0000 (11:49 -0700)]
spl: x86: Correct the binman symbols for SPL
These symbols are incorrect, meaning that binman cannot find the
associated entry. This leads to errors like:
binman: Section '/binman/simple-bin': Symbol '_binman_spl_prop_size'
in entry '/binman/simple-bin/u-boot-spl/u-boot-spl-nodtb':
Entry 'spl' not found in list (mkimage,u-boot-spl-nodtb,
u-boot-spl-bss-pad,u-boot-spl-dtb,u-boot-spl,u-boot-img,main-section)
Simon Glass [Tue, 8 Feb 2022 18:49:46 +0000 (11:49 -0700)]
moveconfig: Allow regex matches when finding combinations
It is useful to be able to search for CONFIG options that match a regex,
such as this, which lists boards which define SPL_FIT_GENERATOR and
anything not starting with ROCKCHIP:
Binman keeps track of positions of each entry in the final image, but
currently this data is wrong for things included in FIT entries,
especially since a previous patch makes FIT a subclass of Section and
inherit its implementation.
There are three ways to put data into a FIT image. It can be directly
included as a "data" property, or it can be external to the FIT image
represented by an offset-size pair of properties. This external offset
is either "data-position" from the start of the FIT or "data-offset"
from the end of the FIT, and the size is "data-size" for both. However,
binman doesn't use the "data-offset" method while building FIT entries.
According to the Section docstring, its subclasses should calculate and
set the correct offsets and sizes in SetImagePos() method. Do this for
FIT subentries for the three ways mentioned above, and add tests for the
two ways binman can pack them in.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
binman: Skip processing "hash" subnodes of FIT subsections
Binman's FIT entry type can have image subentries with "hash" subnodes
intended to be processed by mkimage, but not binman. However, the Entry
class and any subclass that reuses its implementation tries to process
these unconditionally. This can lead to an error when boards specify
hash algorithms that binman doesn't support, but mkimage supports.
Let entries skip processing these "hash" subnodes based on an instance
variable, and set this instance variable for FIT subsections. Also
re-enable processing of calculated and missing properties of FIT entries
which was disabled to mitigate this issue.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Neal Liu [Tue, 15 Feb 2022 10:14:40 +0000 (18:14 +0800)]
crypto: aspeed: fix polling RSA status wrong issue
Check interrupt status to see if RSA engine is completed. After completion
of the task, write-clear the status to finish operation.
Add missing register base for completion.
Fixes: 89c36cca0b6 ("crypto: aspeed: Add AST2600 ACRY support") Signed-off-by: Neal Liu <neal_liu@aspeedtech.com> Reviewed-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
projects / u-boot.git / log
