From: Manoj Sai Date: Fri, 17 Feb 2023 11:58:45 +0000 (+0530) Subject: rk3566: radxa-cm3: Enable USB2.0, USB3.0 support X-Git-Url: http://git.dujemihanovic.xyz/img/static/git-logo.png?a=commitdiff_plain;h=5aedc8bf0ff72c4f09a56fdea59da9357d5fbd4e;p=u-boot.git rk3566: radxa-cm3: Enable USB2.0, USB3.0 support => usb start starting USB... Bus usb@fd000000: Register 2000140 NbrPorts 2 Starting the controller USB XHCI 1.10 Bus usb@fd800000: USB EHCI 1.00 scanning bus usb@fd000000 for devices... cannot reset port 1!? 2 USB Device(s) found scanning bus usb@fd800000 for devices... 4 USB Device(s) found scanning usb for storage devices... 2 Storage Device(s) found => usb tree USB device tree: 1 Hub (5 Gb/s, 0mA) | U-Boot XHCI Host Controller | +-2 Mass Storage (5 Gb/s, 224mA) SanDisk Dual Drive 04019c9b2e1a58f24ee318c3c123aa5 1 Hub (480 Mb/s, 0mA) | u-boot EHCI Host Controller | +-2 Hub (480 Mb/s, 100mA) | USB 2.0 Hub | +-3 Mass Storage (480 Mb/s, 500mA) | JetFlash Mass Storage Device 19M7I4ZQFTSC08SU | +-4 Human Interface (12 Mb/s, 98mA) Logitech USB Receiver Co-developed-by: Suniel Mahesh Signed-off-by: Suniel Mahesh Signed-off-by: Manoj Sai Reviewed-by: Kever Yang --- diff --git a/configs/radxa-cm3-io-rk3566_defconfig b/configs/radxa-cm3-io-rk3566_defconfig index a79d9b25e3..2100cf2cb2 100644 --- a/configs/radxa-cm3-io-rk3566_defconfig +++ b/configs/radxa-cm3-io-rk3566_defconfig @@ -38,6 +38,7 @@ CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_CMD_GPT=y CONFIG_CMD_MMC=y +CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set # CONFIG_SPL_DOS_PARTITION is not set CONFIG_SPL_OF_CONTROL=y @@ -57,10 +58,20 @@ CONFIG_MMC_SDHCI_SDMA=y CONFIG_MMC_SDHCI_ROCKCHIP=y CONFIG_ETH_DESIGNWARE=y CONFIG_GMAC_ROCKCHIP=y +CONFIG_PHY_ROCKCHIP_INNO_USB2=y +CONFIG_PHY_ROCKCHIP_NANENG_COMBOPHY=y CONFIG_REGULATOR_PWM=y +CONFIG_DM_REGULATOR_GPIO=y CONFIG_PWM_ROCKCHIP=y CONFIG_SPL_RAM=y CONFIG_BAUDRATE=1500000 CONFIG_DEBUG_UART_SHIFT=2 CONFIG_SYSRESET=y +CONFIG_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_DWC3=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_EHCI_GENERIC=y +CONFIG_USB_DWC3=y +CONFIG_USB_DWC3_GENERIC=y CONFIG_ERRNO_STR=y