doc: board: Add document for DFU boot on am62x SoCs

Both AM62 SK and beagleplay support DFU boot in a similar way now;
Document how to actually run DFU boot for both boards

Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # on beagle play
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>

diff --git a/doc/board/beagle/am62x_beagleplay.rst b/doc/board/beagle/am62x_beagleplay.rst
index 7784e62b0b7183cef4cc5ede2057b562d10561fe..cdc610264e151e114d375e4fd60d137754e73249 100644 (file)
--- a/doc/board/beagle/am62x_beagleplay.rst
+++ b/doc/board/beagle/am62x_beagleplay.rst
@@ -268,7 +268,19 @@ for details.
      - USB Device Firmware Upgrade (DFU) mode
 
 To switch to SD card boot mode, hold the USR button while powering on
-with Type-C power supply, then release when power LED lights up.
+with a USB type C power supply, then release when power LED lights up.
+
+DFU based boot
+--------------
+
+To boot the board over DFU, ensure there is no SD card inserted with a
+bootloader. Hold the USR switch while plugging into the type C to boot into DFU
+mode. After power-on the build artifacts needs to be uploaded one by one with a
+tool like dfu-util.
+
+.. include::  ../ti/am62x_sk.rst
+    :start-after: .. am62x_evm_rst_include_start_dfu_boot
+    :end-before: .. am62x_evm_rst_include_end_dfu_boot
 
 Debugging U-Boot
 ----------------

diff --git a/doc/board/ti/am62x_sk.rst b/doc/board/ti/am62x_sk.rst
index b12dc85f06b50a80e657f17b0a325863d51dcba4..d5f7fe3b036a44c9abad124b18666f686d3459c1 100644 (file)
--- a/doc/board/ti/am62x_sk.rst
+++ b/doc/board/ti/am62x_sk.rst
@@ -105,6 +105,20 @@ Set the variables corresponding to this platform:
 
 * 3.1 R5:
 
+.. include::  ../ti/k3.rst
+    :start-after: .. k3_rst_include_start_build_steps_spl_r5
+    :end-before: .. k3_rst_include_end_build_steps_spl_r5
+
+* 3.1.1 Alternative build of R5 for DFU boot:
+
+As the SPL size can get too big when building with support for booting both
+from local storage *and* DFU an extra config fragment should be used to enable
+DFU support (and disable storage support)
+
+.. prompt:: bash $
+
+  export UBOOT_CFG_CORTEXR="${UBOOT_CFG_CORTEXR} am62x_r5_usbdfu.config"
+
 .. include::  ../ti/k3.rst
     :start-after: .. k3_rst_include_start_build_steps_spl_r5
     :end-before: .. k3_rst_include_end_build_steps_spl_r5
@@ -251,6 +265,29 @@ https://www.ti.com/lit/pdf/spruiv7 under the `Boot Mode Pins` section.
 
 For SW2 and SW1, the switch state in the "ON" position = 1.
 
+DFU based boot
+--------------
+
+To boot the board over DFU, set the switches to DFU mode and connect to the
+USB type C DRD port on the board. After power-on the build artifacts needs to be
+uploaded one by one with a tool like dfu-util.
+
+.. am62x_evm_rst_include_start_dfu_boot
+
+The initial ROM will have a DFU alt named `bootloader` for the initial R5 spl
+upload. The next stages as exposed by U-Boot have target alts matching the name
+of the artifacts, for these a USB reset has to be done after each upload.
+
+When using dfu-util the following commands can be used to boot to a U-Boot shell:
+
+.. prompt:: bash $
+
+  dfu-util -a bootloader -D tiboot3.bin
+  dfu-util -R -a tispl -D tispl.bin
+  dfu-util -R -a u-boot.img -D u-boot.img
+
+.. am62x_evm_rst_include_end_dfu_boot
+
 Debugging U-Boot
 ----------------