--- /dev/null
+/*
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include "vsc3316_3308.h"
+
+#define REVISION_ID_REG 0x7E
+#define INTERFACE_MODE_REG 0x79
+#define CURRENT_PAGE_REGISTER 0x7F
+#define CONNECTION_CONFIG_PAGE 0x00
+#define INPUT_STATE_REG 0x13
+#define GLOBAL_INPUT_ISE1 0x51
+#define GLOBAL_INPUT_ISE2 0x52
+#define GLOBAL_INPUT_LOS 0x55
+#define GLOBAL_CORE_CNTRL 0x5D
+#define OUTPUT_MODE_PAGE 0x23
+#define CORE_CONTROL_PAGE 0x25
+#define CORE_CONFIG_REG 0x75
+
+int vsc_if_enable(unsigned int vsc_addr)
+{
+ u8 data;
+
+ debug("VSC:Configuring VSC at I2C address 0x%2x"
+ " for 2-wire interface\n", vsc_addr);
+
+ /* enable 2-wire Serial InterFace (I2C) */
+ data = 0x02;
+ return i2c_write(vsc_addr, INTERFACE_MODE_REG, 1, &data, 1);
+}
+
+int vsc3316_config(unsigned int vsc_addr, const int8_t con_arr[][2],
+ unsigned int num_con)
+{
+ unsigned int i;
+ u8 rev_id = 0;
+ int ret;
+
+ debug("VSC:Initializing VSC3316 at I2C address 0x%2x"
+ " for Tx\n", vsc_addr);
+
+ ret = i2c_read(vsc_addr, REVISION_ID_REG, 1, &rev_id, 1);
+ if (ret < 0) {
+ printf("VSC:0x%x could not read REV_ID from device.\n",
+ vsc_addr);
+ return ret;
+ }
+
+ if (rev_id != 0xab) {
+ printf("VSC: device at address 0x%x is not VSC3316/3308.\n",
+ vsc_addr);
+ return -ENODEV;
+ }
+
+ ret = vsc_if_enable(vsc_addr);
+ if (ret) {
+ printf("VSC:0x%x could not configured for 2-wire I/F.\n",
+ vsc_addr);
+ return ret;
+ }
+
+ /* config connections - page 0x00 */
+ i2c_reg_write(vsc_addr, CURRENT_PAGE_REGISTER, CONNECTION_CONFIG_PAGE);
+
+ /* Making crosspoint connections, by connecting required
+ * input to output */
+ for (i = 0; i < num_con ; i++)
+ i2c_reg_write(vsc_addr, con_arr[i][1], con_arr[i][0]);
+
+ /* input state - page 0x13 */
+ i2c_reg_write(vsc_addr, CURRENT_PAGE_REGISTER, INPUT_STATE_REG);
+ /* Configuring the required input of the switch */
+ for (i = 0; i < num_con ; i++)
+ i2c_reg_write(vsc_addr, con_arr[i][0], 0x80);
+
+ /* Setting Global Input LOS threshold value */
+ i2c_reg_write(vsc_addr, GLOBAL_INPUT_LOS, 0x60);
+
+ /* config output mode - page 0x23 */
+ i2c_reg_write(vsc_addr, CURRENT_PAGE_REGISTER, OUTPUT_MODE_PAGE);
+ /* Turn ON the Output driver correspond to required output*/
+ for (i = 0; i < num_con ; i++)
+ i2c_reg_write(vsc_addr, con_arr[i][1], 0);
+
+ /* configure global core control register, Turn on Global core power */
+ i2c_reg_write(vsc_addr, GLOBAL_CORE_CNTRL, 0);
+
+ vsc_wp_config(vsc_addr);
+
+ return 0;
+}
+
+int vsc3308_config(unsigned int vsc_addr, const int8_t con_arr[][2],
+ unsigned int num_con)
+{
+ unsigned int i;
+ u8 rev_id = 0;
+ int ret;
+
+ debug("VSC:Initializing VSC3308 at I2C address 0x%x"
+ " for Tx\n", vsc_addr);
+
+ ret = i2c_read(vsc_addr, REVISION_ID_REG, 1, &rev_id, 1);
+ if (ret < 0) {
+ printf("VSC:0x%x could not read REV_ID from device.\n",
+ vsc_addr);
+ return ret;
+ }
+
+ if (rev_id != 0xab) {
+ printf("VSC: device at address 0x%x is not VSC3316/3308.\n",
+ vsc_addr);
+ return -ENODEV;
+ }
+
+ ret = vsc_if_enable(vsc_addr);
+ if (ret) {
+ printf("VSC:0x%x could not configured for 2-wire I/F.\n",
+ vsc_addr);
+ return ret;
+ }
+
+ /* config connections - page 0x00 */
+ i2c_reg_write(vsc_addr, CURRENT_PAGE_REGISTER, CONNECTION_CONFIG_PAGE);
+
+ /* Making crosspoint connections, by connecting required
+ * input to output */
+ for (i = 0; i < num_con ; i++)
+ i2c_reg_write(vsc_addr, con_arr[i][1], con_arr[i][0]);
+
+ /*Configure Global Input ISE and gain */
+ i2c_reg_write(vsc_addr, GLOBAL_INPUT_ISE1, 0x12);
+ i2c_reg_write(vsc_addr, GLOBAL_INPUT_ISE2, 0x12);
+
+ /* input state - page 0x13 */
+ i2c_reg_write(vsc_addr, CURRENT_PAGE_REGISTER, INPUT_STATE_REG);
+ /* Turning ON the required input of the switch */
+ for (i = 0; i < num_con ; i++)
+ i2c_reg_write(vsc_addr, con_arr[i][0], 0);
+
+ /* Setting Global Input LOS threshold value */
+ i2c_reg_write(vsc_addr, GLOBAL_INPUT_LOS, 0x60);
+
+ /* config output mode - page 0x23 */
+ i2c_reg_write(vsc_addr, CURRENT_PAGE_REGISTER, OUTPUT_MODE_PAGE);
+ /* Turn ON the Output driver correspond to required output*/
+ for (i = 0; i < num_con ; i++)
+ i2c_reg_write(vsc_addr, con_arr[i][1], 0);
+
+ /* configure global core control register, Turn on Global core power */
+ i2c_reg_write(vsc_addr, GLOBAL_CORE_CNTRL, 0);
+
+ vsc_wp_config(vsc_addr);
+
+ return 0;
+}
+
+void vsc_wp_config(unsigned int vsc_addr)
+{
+ debug("VSC:Configuring VSC at address:0x%x for WP\n", vsc_addr);
+
+ /* For new crosspoint configuration to occur, WP bit of
+ * CORE_CONFIG_REG should be set 1 and then reset to 0 */
+ i2c_reg_write(vsc_addr, CORE_CONFIG_REG, 0x01);
+ i2c_reg_write(vsc_addr, CORE_CONFIG_REG, 0x0);
+}
--- /dev/null
+/*
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __VSC_CROSSBAR_H_
+#define __VSC_CROSSBAR_H 1_
+
+#include <common.h>
+#include <i2c.h>
+#include <errno.h>
+
+int vsc_if_enable(unsigned int vsc_addr);
+int vsc3316_config(unsigned int vsc_addr, const int8_t con_arr[][2],
+ unsigned int num_con);
+int vsc3308_config(unsigned int vsc_addr, const int8_t con_arr[][2],
+ unsigned int num_con);
+void vsc_wp_config(unsigned int vsc_addr);
+
+#endif /* __VSC_CROSSBAR_H_ */
--- /dev/null
+This file contains API information of the initialization code written for
+Vitesse cross-point devices, VSC3316 and VSC3308 for board B4860QDS
+
+Author: Shaveta Leekha <shaveta@freescale.com>
+
+About Device:
+=============
+VSC 3316/3308 is a low-power, low-cost asynchronous crosspoint switch capable of data rates upto 11.5Gbps.
+
+VSC3316 has 16 input and 16 output ports whereas VSC3308 has 8 input and 8 output ports. Programming of these devices are performed by two-wire or four-wire serial interface.
+
+Initialization:
+===============
+On reset, VSC devices are in low-power state with all inputs, outputs and connections in an off state.
+First thing required is to program it to interface with either two-wire or four-wire interface.
+In our case the interface is two-wire I2C serial interface. So the value in Interface mode register at address 79.h to be written is 0x02 for two-wire interface. Also for crosspoint connections to be activated, 01.h value need to be written in 75.h (core configuration register).
+
+API Overview:
+=============
+
+ vsc_if_enable(u8 vsc_addr):
+ --------------------------
+ This API programs VSC to interface with either two-wire or four-wire interface. In our case the interface is two-wire I2C serial interface. So the value in Interface mode register at address 79.h to be written is 0x02 for two-wire interface.
+ Parameters:
+ vsc_addr - Address of the VSC device on board.
+
+
+ vsc3316_config(u8 vsc_addr, int con_arr[][2], u8 num_con):
+ ---------------------------------------------------------
+ This API configures the VSC3316 device for required connections. Connection through the VSC device requires the inputs and outputs to be properly configured.
+ Connection registers are on page 00. It Configures the selected input and output correctly and join them to make a connection. It also program Input state register, Global input ISE, Global input LOS, Global core control, Output mode register and core control registers etc.
+ vsc3308_config(u8 vsc_addr, int con_arr[][2], u8 num_con) does the essential configurations for VSC3308.
+
+ Parameters:
+ vsc_addr - Address of the VSC device on board.
+ con_arr - connection array
+ num_con - number of connections to be configured
+
+ vsc_wp_config(u8 vsc_addr):
+ --------------------------
+ For crosspoint connections to be activated, 01.h value need to be written in 75.h (core configuration register), which is done by this API.
+ Parameters:
+ vsc_addr - Address of the VSC device on board.
projects / u-boot.git / commitdiff
