sun5i-a13-hsg-h702.dtb \
sun5i-a13-inet-86vs.dtb \
sun5i-a13-inet-98v-rev2.dtb \
+ sun5i-a13-licheepi-one.dtb \
sun5i-a13-olinuxino.dtb \
sun5i-a13-olinuxino-micro.dtb \
+ sun5i-a13-pocketbook-touch-lux-3.dtb \
sun5i-a13-q8-tablet.dtb \
sun5i-a13-utoo-p66.dtb \
sun5i-gr8-chip-pro.dtb \
+ sun5i-gr8-evb.dtb \
sun5i-r8-chip.dtb
dtb-$(CONFIG_MACH_SUN6I) += \
sun6i-a31-app4-evb1.dtb \
sun8i-a23-evb.dtb \
sun8i-a23-gt90h-v4.dtb \
sun8i-a23-inet86dz.dtb \
+ sun8i-a23-ippo-q8h-v1.2.dtb \
+ sun8i-a23-ippo-q8h-v5.dtb \
sun8i-a23-polaroid-mid2407pxe03.dtb \
sun8i-a23-polaroid-mid2809pxe04.dtb \
sun8i-a23-q8-tablet.dtb
dtb-$(CONFIG_MACH_SUN8I_A33) += \
+ sun8i-a33-et-q8-v1.6.dtb \
sun8i-a33-ga10h-v1.1.dtb \
sun8i-a33-inet-d978-rev2.dtb \
+ sun8i-a33-ippo-q8h-v1.2.dtb \
sun8i-a33-olinuxino.dtb \
sun8i-a33-q8-tablet.dtb \
sun8i-a33-sinlinx-sina33.dtb \
sun8i-r16-bananapi-m2m.dtb \
- sun8i-r16-nintendo-nes-classic-edition.dtb \
+ sun8i-r16-nintendo-nes-classic.dtb \
+ sun8i-r16-nintendo-super-nes-classic.dtb \
sun8i-r16-parrot.dtb
dtb-$(CONFIG_MACH_SUN8I_A83T) += \
sun8i-a83t-allwinner-h8homlet-v2.dtb \
interrupt-controller;
#interrupt-cells = <1>;
- ac_power_supply: ac-power-supply {
+ ac_power_supply: ac-power {
compatible = "x-powers,axp221-ac-power-supply";
status = "disabled";
};
- battery_power_supply: battery-power-supply {
+ axp_adc: adc {
+ compatible = "x-powers,axp221-adc";
+ #io-channel-cells = <1>;
+ };
+
+ battery_power_supply: battery-power {
compatible = "x-powers,axp221-battery-power-supply";
status = "disabled";
};
};
};
- usb_power_supply: usb_power_supply {
+ usb_power_supply: usb-power {
compatible = "x-powers,axp221-usb-power-supply";
status = "disabled";
};
pinctrl-names = "default";
pinctrl-0 = <&led_pins_t003>;
- red {
+ led {
label = "t003-tv-dongle:red:usr";
gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>; /* PB2 */
default-state = "on";
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp152: pmic@30 {
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_t003>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 6 1 GPIO_ACTIVE_LOW>; /* PG1 */
};
&pio {
- mmc0_cd_pin_t003: mmc0_cd_pin@0 {
- pins = "PG1";
- function = "gpio_in";
- bias-pull-up;
- };
-
- led_pins_t003: led_pins@0 {
+ led_pins_t003: led-pin {
pins = "PB2";
function = "gpio_out";
drive-strength = <20>;
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
pinctrl-names = "default";
pinctrl-0 = <&led_pins_t004>;
- red {
+ led {
label = "t004-tv-dongle:red:usr";
gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>; /* PB2 */
default-state = "on";
reg_vmmc1: vmmc1 {
compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc1_vcc_en_pin_t004>;
regulator-name = "vmmc1";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp152: pmic@30 {
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_t004>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 6 1 GPIO_ACTIVE_LOW>; /* PG1 */
};
&mmc1 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc1_pins_a>;
vmmc-supply = <®_vmmc1>;
bus-width = <4>;
non-removable;
};
&pio {
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
- pins = "PG12";
- function = "gpio_in";
- bias-pull-up;
- };
-
- mmc0_cd_pin_t004: mmc0_cd_pin@0 {
- pins = "PG1";
- function = "gpio_in";
- bias-pull-up;
- };
-
- mmc1_vcc_en_pin_t004: mmc1_vcc_en_pin@0 {
- pins = "PB18";
- function = "gpio_out";
- };
-
- led_pins_t004: led_pins@0 {
+ led_pins_t004: led-pin {
pins = "PB2";
function = "gpio_out";
drive-strength = <20>;
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
};
&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_detect_pin>;
- usb0_id_det-gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+ usb0_id_det-gpios = <&pio 6 12 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PG12 */
usb1_vbus-supply = <®_usb1_vbus>;
status = "okay";
};
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins_mk802>;
- red {
+ led {
label = "mk802:red:usr";
gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>; /* PB2 */
};
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp152: pmic@30 {
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_mk802>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 6 1 GPIO_ACTIVE_LOW>; /* PG1 */
};
&mmc1 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc1_pins_a>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
non-removable;
status = "okay";
};
-&pio {
- led_pins_mk802: led_pins@0 {
- pins = "PB2";
- function = "gpio_out";
- };
-
- mmc0_cd_pin_mk802: mmc0_cd_pin@0 {
- pins = "PG1";
- function = "gpio_in";
- bias-pull-up;
- };
-
- usb1_vbus_pin_mk802: usb1_vbus_pin@0 {
- pins = "PB10";
- function = "gpio_out";
- };
-};
-
®_usb1_vbus {
- pinctrl-0 = <&usb1_vbus_pin_mk802>;
gpio = <&pio 1 10 GPIO_ACTIVE_HIGH>; /* PB10 */
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
pinctrl-names = "default";
pinctrl-0 = <&led_pins_olinuxino>;
- green {
+ led {
label = "a10s-olinuxino-micro:green:usr";
gpios = <&pio 4 3 GPIO_ACTIVE_HIGH>;
default-state = "on";
&emac {
pinctrl-names = "default";
- pinctrl-0 = <&emac_pins_b>;
- phy = <&phy1>;
+ pinctrl-0 = <&emac_pa_pins>;
+ phy-handle = <&phy1>;
status = "okay";
};
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp152: pmic@30 {
#include "axp152.dtsi"
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
- at24@50 {
+ eeprom@50 {
compatible = "atmel,24c16";
pagesize = <16>;
reg = <0x50>;
};
&i2c2 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
};
vref-supply = <®_vcc3v0>;
status = "okay";
- button@191 {
+ button-191 {
label = "Volume Up";
linux,code = <KEY_VOLUMEUP>;
channel = <0>;
voltage = <191274>;
};
- button@392 {
+ button-392 {
label = "Volume Down";
linux,code = <KEY_VOLUMEDOWN>;
channel = <0>;
voltage = <392644>;
};
- button@601 {
+ button-601 {
label = "Menu";
linux,code = <KEY_MENU>;
channel = <0>;
voltage = <601151>;
};
- button@795 {
+ button-795 {
label = "Enter";
linux,code = <KEY_ENTER>;
channel = <0>;
voltage = <795090>;
};
- button@987 {
+ button-987 {
label = "Home";
linux,code = <KEY_HOMEPAGE>;
channel = <0>;
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_olinuxino_micro>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 6 1 GPIO_ACTIVE_LOW>; /* PG1 */
};
&mmc1 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc1_pins_a>, <&mmc1_cd_pin_olinuxino_micro>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 6 13 GPIO_ACTIVE_LOW>; /* PG13 */
};
&pio {
- mmc0_cd_pin_olinuxino_micro: mmc0_cd_pin@0 {
- pins = "PG1";
- function = "gpio_in";
- bias-pull-up;
- };
-
- mmc1_cd_pin_olinuxino_micro: mmc1_cd_pin@0 {
- pins = "PG13";
- function = "gpio_in";
- bias-pull-up;
- };
-
- led_pins_olinuxino: led_pins@0 {
+ led_pins_olinuxino: led-pin {
pins = "PE3";
function = "gpio_out";
drive-strength = <20>;
};
-
- usb1_vbus_pin_olinuxino_m: usb1_vbus_pin@0 {
- pins = "PB10";
- function = "gpio_out";
- };
-
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
- pins = "PG12";
- function = "gpio_in";
- bias-pull-up;
- };
};
®_usb0_vbus {
};
®_usb1_vbus {
- pinctrl-0 = <&usb1_vbus_pin_olinuxino_m>;
gpio = <&pio 1 10 GPIO_ACTIVE_HIGH>;
status = "okay";
};
&spi2 {
pinctrl-names = "default";
- pinctrl-0 = <&spi2_pins_b>,
- <&spi2_cs0_pins_b>;
+ pinctrl-0 = <&spi2_pb_pins>,
+ <&spi2_cs0_pb_pin>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
&uart2 {
pinctrl-names = "default";
- pinctrl-0 = <&uart2_pins_b>;
+ pinctrl-0 = <&uart2_pc_pins>;
status = "okay";
};
&uart3 {
pinctrl-names = "default";
- pinctrl-0 = <&uart3_pins_a>;
+ pinctrl-0 = <&uart3_pg_pins>;
status = "okay";
};
};
&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_detect_pin>;
- usb0_id_det-gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+ usb0_id_det-gpios = <&pio 6 12 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PG12 */
usb0_vbus-supply = <®_usb0_vbus>;
usb1_vbus-supply = <®_usb1_vbus>;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&led_pins_r7>;
- green {
+ led {
label = "r7-tv-dongle:green:usr";
gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>;
default-state = "on";
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_r7>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 6 1 GPIO_ACTIVE_LOW>; /* PG1 */
};
&mmc1 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc1_pins_a>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
non-removable;
};
&pio {
- mmc0_cd_pin_r7: mmc0_cd_pin@0 {
- pins = "PG1";
- function = "gpio_in";
- bias-pull-up;
- };
-
- led_pins_r7: led_pins@0 {
+ led_pins_r7: led-pin {
pins = "PB2";
function = "gpio_out";
drive-strength = <20>;
};
-
- usb1_vbus_pin_r7: usb1_vbus_pin@0 {
- pins = "PG13";
- function = "gpio_out";
- };
};
®_usb1_vbus {
- pinctrl-0 = <&usb1_vbus_pin_r7>;
gpio = <&pio 6 13 GPIO_ACTIVE_HIGH>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins_wobo_i5>;
- blue {
+ led {
label = "a10s-wobo-i5:blue:usr";
gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>;
default-state = "on";
reg_emac_3v3: emac-3v3 {
compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&emac_power_pin_wobo>;
regulator-name = "emac-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
&emac {
pinctrl-names = "default";
- pinctrl-0 = <&emac_pins_a>;
- phy = <&phy1>;
+ pinctrl-0 = <&emac_pd_pins>;
+ phy-handle = <&phy1>;
status = "okay";
};
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_wobo_i5>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 1 3 GPIO_ACTIVE_LOW>; /* PB3 */
status = "okay";
};
-&pio {
- led_pins_wobo_i5: led_pins@0 {
- pins = "PB2";
- function = "gpio_out";
- };
-
- mmc0_cd_pin_wobo_i5: mmc0_cd_pin@0 {
- pins = "PB3";
- function = "gpio_in";
- bias-pull-up;
- };
-
- emac_power_pin_wobo: emac_power_pin@0 {
- pins = "PA02";
- function = "gpio_out";
- };
-};
-
®_dcdc2 {
regulator-always-on;
regulator-min-microvolt = <1000000>;
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#include "skeleton.dtsi"
-
#include "sun5i.dtsi"
#include <dt-bindings/dma/sun4i-a10.h>
/ {
- interrupt-parent = <&intc>;
-
aliases {
ethernet0 = &emac;
};
#size-cells = <1>;
ranges;
- framebuffer@2 {
+ framebuffer-lcd0-hdmi {
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0-hdmi";
allwinner,pipelines = <&fe0>;
};
- soc@1c00000 {
+ soc {
hdmi: hdmi@1c16000 {
compatible = "allwinner,sun5i-a10s-hdmi";
reg = <0x01c16000 0x1000>;
};
hdmi_out: port@1 {
- #address-cells = <1>;
- #size-cells = <0>;
reg = <1>;
};
};
compatible = "allwinner,sun5i-a10s-ccu";
};
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+};
+
&pio {
compatible = "allwinner,sun5i-a10s-pinctrl";
- uart0_pins_a: uart0@0 {
+ uart0_pb_pins: uart0-pb-pins {
pins = "PB19", "PB20";
function = "uart0";
};
- uart2_pins_b: uart2@1 {
+ uart2_pc_pins: uart2-pc-pins {
pins = "PC18", "PC19";
function = "uart2";
};
- emac_pins_b: emac0@1 {
+ emac_pa_pins: emac-pa-pins {
pins = "PA0", "PA1", "PA2",
"PA3", "PA4", "PA5", "PA6",
"PA7", "PA8", "PA9", "PA10",
function = "emac";
};
- mmc1_pins_a: mmc1@0 {
+ mmc1_pins: mmc1-pins {
pins = "PG3", "PG4", "PG5",
"PG6", "PG7", "PG8";
function = "mmc1";
drive-strength = <30>;
};
- spi2_pins_b: spi2@1 {
+ spi2_pb_pins: spi2-pb-pins {
pins = "PB12", "PB13", "PB14";
function = "spi2";
};
- spi2_cs0_pins_b: spi2_cs0@1 {
+ spi2_cs0_pb_pin: spi2-cs0-pb-pin {
pins = "PB11";
function = "spi2";
};
};
-&sram_a {
-};
-
&tcon0_out {
tcon0_out_hdmi: endpoint@2 {
reg = <2>;
&uart1 {
pinctrl-names = "default";
- pinctrl-0 = <&uart1_pins_b>;
+ pinctrl-0 = <&uart1_pg_pins>;
status = "okay";
};
pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
default-brightness-level = <8>;
+ power-supply = <®_vcc3v3>;
/* TODO: backlight uses axp gpio1 as enable pin */
};
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
#include "axp209.dtsi"
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
pcf8563: rtc@51 {
vref-supply = <®_ldo2>;
status = "okay";
- button@200 {
+ button-200 {
label = "Volume Up";
linux,code = <KEY_VOLUMEUP>;
channel = <0>;
voltage = <200000>;
};
- button@400 {
+ button-400 {
label = "Volume Down";
linux,code = <KEY_VOLUMEDOWN>;
channel = <0>;
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_d709>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
status = "okay";
};
-&pio {
- mmc0_cd_pin_d709: mmc0_cd_pin@0 {
- pins = "PG0";
- function = "gpio_in";
- bias-pull-up;
- };
-
- usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
- pins = "PG1";
- function = "gpio_in";
- bias-pull-down;
- };
-
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
- pins = "PG2";
- function = "gpio_in";
- bias-pull-up;
- };
-};
-
&pwm {
pinctrl-names = "default";
- pinctrl-0 = <&pwm0_pins>;
+ pinctrl-0 = <&pwm0_pin>;
status = "okay";
};
&uart1 {
pinctrl-names = "default";
- pinctrl-0 = <&uart1_pins_b>;
+ pinctrl-0 = <&uart1_pg_pins>;
status = "okay";
};
};
&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
- usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
- usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
+ usb0_id_det-gpios = <&pio 6 2 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PG2 */
+ usb0_vbus_det-gpios = <&pio 6 1 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; /* PG1 */
usb0_vbus-supply = <®_usb0_vbus>;
usb1_vbus-supply = <®_ldo3>;
status = "okay";
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
};
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
pcf8563: rtc@51 {
};
&i2c2 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
};
vref-supply = <®_ldo2>;
status = "okay";
- button@200 {
+ button-200 {
label = "Volume Up";
linux,code = <KEY_VOLUMEUP>;
channel = <0>;
voltage = <200000>;
};
- button@400 {
+ button-400 {
label = "Volume Down";
linux,code = <KEY_VOLUMEDOWN>;
channel = <0>;
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_h702>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
status = "okay";
};
-&pio {
- mmc0_cd_pin_h702: mmc0_cd_pin@0 {
- pins = "PG0";
- function = "gpio_in";
- bias-pull-up;
- };
-
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
- pins = "PG2";
- function = "gpio_in";
- bias-pull-up;
- };
-
- usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
- pins = "PG1";
- function = "gpio_in";
- };
-};
-
#include "axp209.dtsi"
®_dcdc2 {
&uart1 {
pinctrl-names = "default";
- pinctrl-0 = <&uart1_pins_b>;
+ pinctrl-0 = <&uart1_pg_pins>;
status = "okay";
};
};
&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
- usb0_id_det-gpios = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
+ usb0_id_det-gpios = <&pio 6 2 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PG2 */
usb0_vbus_det-gpios = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
usb0_vbus-supply = <®_usb0_vbus>;
usb1_vbus-supply = <®_ldo3>;
&uart1 {
pinctrl-names = "default";
- pinctrl-0 = <&uart1_pins_b>;
+ pinctrl-0 = <&uart1_pg_pins>;
status = "okay";
};
--- /dev/null
+/*
+ * Copyright 2016 Icenowy Zheng <icenowy@aosc.xyz>
+ *
+ * Based on sun5i-a13-olinuxino.dts, which is
+ * Copyright 2012 Maxime Ripard <maxime.ripard@free-electrons.com>
+ * Copyright 2013 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun5i-a13.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Lichee Pi One";
+ compatible = "licheepi,licheepi-one", "allwinner,sun5i-a13";
+
+ aliases {
+ serial0 = &uart1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-0 {
+ label ="licheepi:red:usr";
+ gpios = <&pio 2 5 GPIO_ACTIVE_LOW>;
+ };
+
+ led-1 {
+ label ="licheepi:green:usr";
+ gpios = <&pio 2 19 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+
+ led-2 {
+ label ="licheepi:blue:usr";
+ gpios = <&pio 2 4 GPIO_ACTIVE_LOW>;
+ };
+
+ };
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ axp209: pmic@34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupts = <0>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+};
+
+&i2c1 {
+ status = "disabled";
+};
+
+&i2c2 {
+ status = "disabled";
+};
+
+&lradc {
+ vref-supply = <®_ldo2>;
+ status = "okay";
+
+ button-984 {
+ label = "Home";
+ linux,code = <KEY_HOMEPAGE>;
+ channel = <0>;
+ voltage = <984126>;
+ };
+};
+
+&mmc0 {
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ broken-cd;
+ status = "okay";
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_4bit_pc_pins>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ broken-cd;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&otg_sram {
+ status = "okay";
+};
+
+#include "axp209.dtsi"
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-dll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_ldo3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "csi-1.8v";
+};
+
+®_ldo4 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "csi-2.8v";
+};
+
+®_usb0_vbus {
+ gpio = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 */
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pg_pins>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usbphy {
+ usb0_id_det-gpios = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
+ usb0_vbus_det-gpios = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
+ usb0_vbus-supply = <®_usb0_vbus>;
+ usb1_vbus-supply = <®_vcc5v0>;
+ status = "okay";
+};
pinctrl-names = "default";
pinctrl-0 = <&led_pins_olinuxinom>;
- power {
+ led {
label = "a13-olinuxino-micro:green:power";
gpios = <&pio 6 9 GPIO_ACTIVE_HIGH>;
default-state = "on";
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
};
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
};
&i2c2 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_olinuxinom>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
};
&pio {
- mmc0_cd_pin_olinuxinom: mmc0_cd_pin@0 {
- pins = "PG0";
- function = "gpio_in";
- bias-pull-up;
- };
-
- led_pins_olinuxinom: led_pins@0 {
+ led_pins_olinuxinom: led-pin {
pins = "PG9";
function = "gpio_out";
drive-strength = <20>;
};
-
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
- pins = "PG2";
- function = "gpio_in";
- bias-pull-up;
- };
-
- usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
- pins = "PG1";
- function = "gpio_in";
- bias-pull-down;
- };
-
- usb0_vbus_pin_olinuxinom: usb0_vbus_pin@0 {
- pins = "PG12";
- function = "gpio_out";
- };
-
- usb1_vbus_pin_olinuxinom: usb1_vbus_pin@0 {
- pins = "PG11";
- function = "gpio_out";
- };
};
®_usb0_vbus {
- pinctrl-0 = <&usb0_vbus_pin_olinuxinom>;
gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>;
status = "okay";
};
®_usb1_vbus {
- pinctrl-0 = <&usb1_vbus_pin_olinuxinom>;
gpio = <&pio 6 11 GPIO_ACTIVE_HIGH>;
status = "okay";
};
&uart1 {
pinctrl-names = "default";
- pinctrl-0 = <&uart1_pins_b>;
+ pinctrl-0 = <&uart1_pg_pins>;
status = "okay";
};
};
&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
- usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
- usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
+ usb0_id_det-gpios = <&pio 6 2 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PG2 */
+ usb0_vbus_det-gpios = <&pio 6 1 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; /* PG1 */
usb0_vbus-supply = <®_usb0_vbus>;
usb1_vbus-supply = <®_usb1_vbus>;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&led_pins_olinuxino>;
- power {
+ led {
gpios = <&pio 6 9 GPIO_ACTIVE_HIGH>;
default-state = "on";
};
bridge {
compatible = "dumb-vga-dac";
- #address-cells = <1>;
- #size-cells = <0>;
ports {
#address-cells = <1>;
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
};
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
};
&i2c2 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
};
vref-supply = <®_vcc3v0>;
status = "okay";
- button@191 {
+ button-191 {
label = "Volume Up";
linux,code = <KEY_VOLUMEUP>;
channel = <0>;
voltage = <191274>;
};
- button@392 {
+ button-392 {
label = "Volume Down";
linux,code = <KEY_VOLUMEDOWN>;
channel = <0>;
voltage = <392644>;
};
- button@601 {
+ button-601 {
label = "Menu";
linux,code = <KEY_MENU>;
channel = <0>;
voltage = <601151>;
};
- button@795 {
+ button-795 {
label = "Enter";
linux,code = <KEY_ENTER>;
channel = <0>;
voltage = <795090>;
};
- button@987 {
+ button-987 {
label = "Home";
linux,code = <KEY_HOMEPAGE>;
channel = <0>;
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_olinuxino>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
};
&pio {
- mmc0_cd_pin_olinuxino: mmc0_cd_pin@0 {
- pins = "PG0";
- function = "gpio_in";
- bias-pull-up;
- };
-
- led_pins_olinuxino: led_pins@0 {
+ led_pins_olinuxino: led-pin {
pins = "PG9";
function = "gpio_out";
drive-strength = <20>;
};
-
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
- pins = "PG2";
- function = "gpio_in";
- bias-pull-up;
- };
-
- usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
- pins = "PG1";
- function = "gpio_in";
- bias-pull-down;
- };
-
- usb1_vbus_pin_olinuxino: usb1_vbus_pin@0 {
- pins = "PG11";
- function = "gpio_out";
- };
};
®_usb0_vbus {
};
®_usb1_vbus {
- pinctrl-0 = <&usb1_vbus_pin_olinuxino>;
gpio = <&pio 6 11 GPIO_ACTIVE_HIGH>;
status = "okay";
};
&uart1 {
pinctrl-names = "default";
- pinctrl-0 = <&uart1_pins_b>;
+ pinctrl-0 = <&uart1_pg_pins>;
status = "okay";
};
};
&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
- usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
- usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
+ usb0_id_det-gpios = <&pio 6 2 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PG2 */
+ usb0_vbus_det-gpios = <&pio 6 1 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; /* PG1 */
usb0_vbus-supply = <®_usb0_vbus>;
usb1_vbus-supply = <®_usb1_vbus>;
status = "okay";
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright 2019 Ondrej Jirman <megous@megous.com>
+ */
+
+/dts-v1/;
+#include "sun5i-a13.dtsi"
+#include "sunxi-common-regulators.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+ model = "PocketBook Touch Lux 3";
+ compatible = "pocketbook,touch-lux-3", "allwinner,sun5i-a13";
+
+ aliases {
+ serial0 = &uart1;
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ i2c2 = &i2c2;
+ };
+
+ backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+ enable-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
+ brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+ default-brightness-level = <8>;
+ power-supply = <®_vcc3v3>;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led {
+ gpios = <&pio 4 8 GPIO_ACTIVE_LOW>; /* PE8 */
+ default-state = "on";
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ autorepeat;
+ label = "GPIO Keys";
+
+ key-right {
+ label = "Right";
+ linux,code = <KEY_RIGHT>;
+ gpios = <&pio 6 9 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PG9 */
+ };
+
+ key-left {
+ label = "Left";
+ linux,code = <KEY_LEFT>;
+ gpios = <&pio 6 10 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PG10 */
+ };
+ };
+
+ reg_1v8: regulator-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd-1v8-nor-ctp";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&pio 2 15 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_1v8_nor: regulator-nor {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd-nor";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&pio 2 14 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <®_1v8>;
+ regulator-always-on;
+ };
+
+ reg_1v8_ctp: regulator-ctp {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd-ctp";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&pio 2 13 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <®_1v8>;
+ };
+
+ reg_3v3_mmc0: regulator-mmc0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd-mmc0";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&pio 4 4 GPIO_ACTIVE_LOW>; /* PE4 */
+ vin-supply = <®_vcc3v3>;
+ };
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ axp209: pmic@34 {
+ reg = <0x34>;
+ interrupts = <0>;
+ };
+};
+
+#include "axp209.dtsi"
+
+&i2c1 {
+ status = "okay";
+
+ pcf8563: rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
+
+&i2c2 {
+ status = "okay";
+
+ /* Touchpanel is connected here. */
+};
+
+&lradc {
+ vref-supply = <®_ldo2>;
+ status = "okay";
+
+ button-200 {
+ label = "Home";
+ linux,code = <KEY_HOME>;
+ channel = <0>;
+ voltage = <200000>;
+ };
+
+ button-400 {
+ label = "Menu";
+ linux,code = <KEY_MENU>;
+ channel = <0>;
+ voltage = <400000>;
+ };
+};
+
+&mmc0 {
+ vmmc-supply = <®_3v3_mmc0>;
+ bus-width = <4>;
+ cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
+ status = "okay";
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_4bit_pc_pins>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&otg_sram {
+ status = "okay";
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_pin>;
+ status = "okay";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vdd-int-pll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_ldo3 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+ /* We need this otherwise the LDO3 would overload */
+ regulator-soft-start;
+ regulator-ramp-delay = <1600>;
+};
+
+&spi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pe_pins>, <&spi2_cs0_pe_pin>;
+ status = "okay";
+
+ epd_flash: flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "macronix,mx25u4033", "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <4000000>;
+ };
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pg_pins>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&battery_power_supply {
+ status = "okay";
+};
+
+&usb_power_supply {
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_ldo3>;
+ status = "okay";
+};
compatible = "allwinner,q8-a13", "allwinner,sun5i-a13";
panel: panel {
- compatible = "urt,umsh-8596md-t", "simple-panel";
- #address-cells = <1>;
- #size-cells = <0>;
+ compatible = "bananapi,s070wv20-ct16";
+ power-supply = <®_vcc3v3>;
+ enable-gpios = <&axp_gpio 0 GPIO_ACTIVE_HIGH>; /* AXP GPIO0 */
+ backlight = <&backlight>;
- port@0 {
- reg = <0>;
- /* TODO: lcd panel uses axp gpio0 as enable pin */
- backlight = <&backlight>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- panel_input: endpoint@0 {
- reg = <0>;
+ port {
+ panel_input: endpoint {
remote-endpoint = <&tcon0_out_lcd>;
};
};
/delete-property/stdout-path;
};
- i2c_lcd: i2c@0 {
+ i2c_lcd: i2c {
/* The lcd panel i2c interface is hooked up via gpios */
compatible = "i2c-gpio";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c_lcd_pins>;
- gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>, /* PG12, sda */
- <&pio 6 10 GPIO_ACTIVE_HIGH>; /* PG10, scl */
+ sda-gpios = <&pio 6 12 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PG12 */
+ scl-gpios = <&pio 6 10 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PG10 */
i2c-gpio,delay-us = <5>;
};
};
allwinner,pa-gpios = <&pio 6 3 GPIO_ACTIVE_HIGH>; /* PG3 */
};
-&codec_pa_pin {
- pins = "PG3";
-};
-
&mmc2 {
pinctrl-names = "default";
- pinctrl-0 = <&mmc2_pins_a>;
+ pinctrl-0 = <&mmc2_8bit_pins>;
vmmc-supply = <®_vcc3v3>;
bus-width = <8>;
non-removable;
};
};
-&pio {
- i2c_lcd_pins: i2c_lcd_pin@0 {
- pins = "PG10", "PG12";
- function = "gpio_out";
- bias-pull-up;
- };
-};
-
®_usb0_vbus {
gpio = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
};
/* The P66 uses the uart pins as gpios */
status = "disabled";
};
-
-&usb0_vbus_pin_a {
- pins = "PB4";
-};
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#include "skeleton.dtsi"
-
#include "sun5i.dtsi"
#include <dt-bindings/thermal/thermal.h>
/ {
- interrupt-parent = <&intc>;
-
thermal-zones {
- cpu_thermal {
+ cpu-thermal {
/* milliseconds */
polling-delay-passive = <250>;
polling-delay = <1000>;
allwinner,pipelines = <&fe0>;
};
- soc@1c00000 {
+ soc {
pwm: pwm@1c20e00 {
compatible = "allwinner,sun5i-a13-pwm";
reg = <0x01c20e00 0xc>;
&cpu0 {
clock-latency = <244144>; /* 8 32k periods */
- operating-points = <
+ operating-points =
/* kHz uV */
- 1008000 1400000
- 912000 1350000
- 864000 1300000
- 624000 1200000
- 576000 1200000
- 432000 1200000
- >;
+ <1008000 1400000>,
+ <912000 1350000>,
+ <864000 1300000>,
+ <624000 1200000>,
+ <576000 1200000>,
+ <432000 1200000>;
#cooling-cells = <2>;
};
mmc0_pwrseq: mmc0_pwrseq {
compatible = "mmc-pwrseq-simple";
- pinctrl-names = "default";
- pinctrl-0 = <&wifi_reg_on_pin_chip_pro>;
reset-gpios = <&pio 1 10 GPIO_ACTIVE_LOW>; /* PB10 */
};
};
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
#include "axp209.dtsi"
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "disabled";
};
&i2s0 {
pinctrl-names = "default";
- pinctrl-0 = <&i2s0_mclk_pins_a>, <&i2s0_data_pins_a>;
+ pinctrl-0 = <&i2s0_mclk_pin>, <&i2s0_data_pins>;
status = "disabled";
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>;
vmmc-supply = <®_vcc3v3>;
mmc-pwrseq = <&mmc0_pwrseq>;
bus-width = <4>;
&nfc {
pinctrl-names = "default";
- pinctrl-0 = <&nand_pins_a &nand_cs0_pins_a &nand_rb0_pins_a>;
+ pinctrl-0 = <&nand_pins &nand_cs0_pin &nand_rb0_pin>;
status = "okay";
nand@0 {
- #address-cells = <2>;
- #size-cells = <2>;
reg = <0>;
allwinner,rb = <0>;
nand-ecc-mode = "hw";
status = "okay";
};
-&pio {
- usb0_id_pin_chip_pro: usb0-id-pin@0 {
- pins = "PG2";
- function = "gpio_in";
- };
-
- wifi_reg_on_pin_chip_pro: wifi-reg-on-pin@0 {
- pins = "PB10";
- function = "gpio_out";
- };
-};
-
&pwm {
pinctrl-names = "default";
- pinctrl-0 = <&pwm0_pins>, <&pwm1_pins>;
+ pinctrl-0 = <&pwm0_pin>, <&pwm1_pins>;
status = "disabled";
};
&uart1 {
pinctrl-names = "default";
- pinctrl-0 = <&uart1_pins_b>, <&uart1_cts_rts_pins_a>;
+ pinctrl-0 = <&uart1_pg_pins>, <&uart1_cts_rts_pins>;
status = "okay";
};
&uart2 {
pinctrl-names = "default";
- pinctrl-0 = <&uart2_pins_a>, <&uart2_cts_rts_pins_a>;
+ pinctrl-0 = <&uart2_pd_pins>, <&uart2_cts_rts_pd_pins>;
status = "disabled";
};
&uart3 {
pinctrl-names = "default";
- pinctrl-0 = <&uart3_pins_a>, <&uart3_cts_rts_pins_a>;
+ pinctrl-0 = <&uart3_pg_pins>, <&uart3_cts_rts_pg_pins>;
status = "okay";
};
};
&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_pin_chip_pro>;
- usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
+ usb0_id_det-gpios = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
usb0_vbus_power-supply = <&usb_power_supply>;
usb1_vbus-supply = <®_vcc5v0>;
status = "okay";
--- /dev/null
+/*
+ * Copyright 2016 Free Electrons
+ * Copyright 2016 NextThing Co
+ *
+ * Mylène Josserand <mylene.josserand@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun5i-gr8.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ model = "NextThing GR8-EVB";
+ compatible = "nextthing,gr8-evb", "nextthing,gr8";
+
+ aliases {
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ i2c2 = &i2c2;
+ serial0 = &uart1;
+ serial1 = &uart2;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm 0 10000 0>;
+ enable-gpios = <&axp_gpio 1 GPIO_ACTIVE_HIGH>;
+ power-supply = <®_vcc3v3>;
+ brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+ default-brightness-level = <8>;
+ };
+
+ sound-analog {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "gr8-evb-wm8978";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,mclk-fs = <512>;
+
+ simple-audio-card,cpu {
+ sound-dai = <&i2s0>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&wm8978>;
+ };
+ };
+
+ sound-spdif {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "On-board SPDIF";
+
+ simple-audio-card,cpu {
+ sound-dai = <&spdif>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&spdif_out>;
+ };
+ };
+
+ spdif_out: spdif-out {
+ #sound-dai-cells = <0>;
+ compatible = "linux,spdif-dit";
+ };
+};
+
+&be0 {
+ status = "okay";
+};
+
+&codec {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ axp209: pmic@34 {
+ reg = <0x34>;
+
+ /*
+ * The interrupt is routed through the "External Fast
+ * Interrupt Request" pin (ball G13 of the module)
+ * directly to the main interrupt controller, without
+ * any other controller interfering.
+ */
+ interrupts = <0>;
+ };
+};
+
+#include "axp209.dtsi"
+
+&i2c1 {
+ status = "okay";
+
+ wm8978: codec@1a {
+ #sound-dai-cells = <0>;
+ compatible = "wlf,wm8978";
+ reg = <0x1a>;
+ };
+
+ pcf8563: rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
+
+&i2c2 {
+ status = "okay";
+};
+
+&i2s0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s0_mclk_pin>, <&i2s0_data_pins>;
+ status = "okay";
+};
+
+&ir0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir0_rx_pin>;
+ status = "okay";
+};
+
+&lradc {
+ vref-supply = <®_ldo2>;
+ status = "okay";
+
+ button-190 {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ channel = <0>;
+ voltage = <190000>;
+ };
+
+ button-390 {
+ label = "Volume Down";
+ linux,code = <KEY_VOLUMEDOWN>;
+ channel = <0>;
+ voltage = <390000>;
+ };
+
+ button-600 {
+ label = "Menu";
+ linux,code = <KEY_MENU>;
+ channel = <0>;
+ voltage = <600000>;
+ };
+
+ button-800 {
+ label = "Search";
+ linux,code = <KEY_SEARCH>;
+ channel = <0>;
+ voltage = <800000>;
+ };
+
+ button-980 {
+ label = "Home";
+ linux,code = <KEY_HOMEPAGE>;
+ channel = <0>;
+ voltage = <980000>;
+ };
+
+ button-1180 {
+ label = "Esc";
+ linux,code = <KEY_ESC>;
+ channel = <0>;
+ voltage = <1180000>;
+ };
+
+ button-1400 {
+ label = "Enter";
+ linux,code = <KEY_ENTER>;
+ channel = <0>;
+ voltage = <1400000>;
+ };
+};
+
+&mmc0 {
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
+ status = "okay";
+};
+
+&nfc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&nand_pins &nand_cs0_pin &nand_rb0_pin>;
+
+ /* MLC Support sucks for now */
+ status = "disabled";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&otg_sram {
+ status = "okay";
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_pin>;
+ status = "okay";
+};
+
+®_dcdc2 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
+ regulator-always-on;
+};
+
+®_dcdc3 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vdd-sys";
+ regulator-always-on;
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "avcc";
+ regulator-always-on;
+};
+
+®_usb1_vbus {
+ gpio = <&pio 6 13 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&rtp {
+ allwinner,ts-attached;
+};
+
+&spdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spdif_tx_pin>;
+ status = "okay";
+};
+
+&tve0 {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pg_pins>, <&uart1_cts_rts_pins>;
+ status = "okay";
+};
+
+&usb_otg {
+ /*
+ * The GR8-EVB has a somewhat interesting design. There's a
+ * pin supposed to control VBUS, an ID pin, a VBUS detect pin,
+ * so everything should work just fine.
+ *
+ * Except that the pin supposed to control VBUS is not
+ * connected to any controllable output, neither to the SoC
+ * through a GPIO or to the PMIC, and it is pulled down,
+ * meaning that we will never be able to enable VBUS on this
+ * board.
+ */
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usb_power_supply {
+ status = "okay";
+};
+
+&usbphy {
+ usb0_id_det-gpios = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
+ usb0_vbus_det-gpios = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
+ usb0_vbus_power-supply = <&usb_power_supply>;
+ usb1_vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};
allwinner,pipelines = <&fe0>;
};
- soc@1c00000 {
+ soc {
pwm: pwm@1c20e00 {
compatible = "allwinner,sun5i-a10s-pwm";
reg = <0x01c20e00 0xc>;
&pio {
compatible = "nextthing,gr8-pinctrl";
- i2s0_data_pins_a: i2s0-data@0 {
+ i2s0_data_pins: i2s0-data-pins {
pins = "PB6", "PB7", "PB8", "PB9";
function = "i2s0";
};
- i2s0_mclk_pins_a: i2s0-mclk@0 {
+ i2s0_mclk_pin: i2s0-mclk-pin {
pins = "PB5";
function = "i2s0";
};
- pwm1_pins: pwm1 {
+ pwm1_pins: pwm1-pin {
pins = "PG13";
function = "pwm1";
};
- spdif_tx_pins_a: spdif@0 {
+ spdif_tx_pin: spdif-tx-pin {
pins = "PB10";
function = "spdif";
bias-pull-up;
};
- uart1_cts_rts_pins_a: uart1-cts-rts@0 {
+ uart1_cts_rts_pins: uart1-cts-rts-pins {
pins = "PG5", "PG6";
function = "uart1";
};
mmc0_pwrseq: mmc0_pwrseq {
compatible = "mmc-pwrseq-simple";
- pinctrl-names = "default";
- pinctrl-0 = <&chip_wifi_reg_on_pin>;
reset-gpios = <&pio 2 19 GPIO_ACTIVE_LOW>; /* PC19 */
};
onewire {
compatible = "w1-gpio";
- gpios = <&pio 3 2 GPIO_ACTIVE_HIGH>; /* PD2 */
- pinctrl-names = "default";
- pinctrl-0 = <&chip_w1_pin>;
+ gpios = <&pio 3 2 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PD2 */
};
};
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
};
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "disabled";
};
&i2c2 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
xio: gpio@38 {
};
};
-&mmc0_pins_a {
+&mmc0_pins {
bias-pull-up;
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>;
vmmc-supply = <®_vcc3v3>;
mmc-pwrseq = <&mmc0_pwrseq>;
bus-width = <4>;
status = "okay";
};
-&pio {
- chip_vbus_pin: chip_vbus_pin@0 {
- pins = "PB10";
- function = "gpio_out";
- };
-
- chip_wifi_reg_on_pin: chip_wifi_reg_on_pin@0 {
- pins = "PC19";
- function = "gpio_out";
- };
-
- chip_id_det_pin: chip_id_det_pin@0 {
- pins = "PG2";
- function = "gpio_in";
- };
-
- chip_w1_pin: chip_w1_pin@0 {
- pins = "PD2";
- function = "gpio_in";
- bias-pull-up;
- };
-};
-
®_dcdc2 {
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1400000>;
};
®_usb0_vbus {
- pinctrl-0 = <&chip_vbus_pin>;
vin-supply = <®_vcc5v0>;
gpio = <&pio 1 10 GPIO_ACTIVE_HIGH>; /* PB10 */
status = "okay";
&spi2 {
pinctrl-names = "default";
- pinctrl-0 = <&spi2_pins_a>;
+ pinctrl-0 = <&spi2_pe_pins>;
status = "disabled";
};
&uart1 {
pinctrl-names = "default";
- pinctrl-0 = <&uart1_pins_b>;
+ pinctrl-0 = <&uart1_pg_pins>;
status = "okay";
};
&uart3 {
pinctrl-names = "default";
- pinctrl-0 = <&uart3_pins_a>,
- <&uart3_cts_rts_pins_a>;
+ pinctrl-0 = <&uart3_pg_pins>,
+ <&uart3_cts_rts_pg_pins>;
status = "okay";
};
};
&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&chip_id_det_pin>;
status = "okay";
- usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
+ usb0_id_det-gpios = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
usb0_vbus_power-supply = <&usb_power_supply>;
usb0_vbus-supply = <®_usb0_vbus>;
usb1_vbus-supply = <®_vcc5v0>;
pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
default-brightness-level = <8>;
- /* TODO: backlight uses axp gpio1 as enable pin */
+ enable-gpios = <&axp_gpio 1 GPIO_ACTIVE_HIGH>; /* AXP GPIO1 */
+ power-supply = <®_vcc3v0>;
};
chosen {
};
&codec {
- pinctrl-names = "default";
- pinctrl-0 = <&codec_pa_pin>;
allwinner,pa-gpios = <&pio 6 10 GPIO_ACTIVE_HIGH>; /* PG10 */
status = "okay";
};
*/
clock-frequency = <400000>;
- touchscreen: touchscreen {
+ touchscreen: touchscreen@40 {
+ reg = <0x40>;
interrupt-parent = <&pio>;
interrupts = <6 11 IRQ_TYPE_EDGE_FALLING>; /* EINT11 (PG11) */
- pinctrl-names = "default";
- pinctrl-0 = <&ts_power_pin>;
power-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */
/* Tablet dts must provide reg and compatible */
status = "disabled";
&mmc0 {
pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ pinctrl-0 = <&mmc0_pins>;
vmmc-supply = <®_vcc3v0>;
bus-width = <4>;
cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
status = "okay";
};
-&pio {
- codec_pa_pin: codec_pa_pin@0 {
- pins = "PG10";
- function = "gpio_out";
- };
-
- mmc0_cd_pin: mmc0_cd_pin@0 {
- pins = "PG0";
- function = "gpio_in";
- bias-pull-up;
- };
-
- ts_power_pin: ts_power_pin {
- pins = "PB3";
- function = "gpio_out";
- drive-strength = <10>;
- bias-disable;
- };
-
- usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
- pins = "PG1";
- function = "gpio_in";
- bias-pull-down;
- };
-
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
- pins = "PG2";
- function = "gpio_in";
- bias-pull-up;
- };
-
- usb0_vbus_pin_a: usb0_vbus_pin@0 {
- pins = "PG12";
- function = "gpio_out";
- };
-};
-
®_dcdc2 {
regulator-always-on;
regulator-min-microvolt = <1000000>;
&uart1 {
pinctrl-names = "default";
- pinctrl-0 = <&uart1_pins_b>;
+ pinctrl-0 = <&uart1_pg_pins>;
status = "okay";
};
};
&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
- usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
- usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
+ usb0_id_det-gpios = <&pio 6 2 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PG2 */
+ usb0_vbus_det-gpios = <&pio 6 1 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; /* PG1 */
usb0_vbus_power-supply = <&usb_power_supply>;
usb0_vbus-supply = <®_usb0_vbus>;
usb1_vbus-supply = <®_ldo3>;
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#include "skeleton.dtsi"
-
#include <dt-bindings/clock/sun5i-ccu.h>
#include <dt-bindings/dma/sun4i-a10.h>
#include <dt-bindings/reset/sun5i-ccu.h>
/ {
interrupt-parent = <&intc>;
+ #address-cells = <1>;
+ #size-cells = <1>;
cpus {
#address-cells = <1>;
#size-cells = <1>;
ranges;
- framebuffer@0 {
+ framebuffer-lcd0 {
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0";
status = "disabled";
};
- framebuffer@1 {
+ framebuffer-lcd0-tve0 {
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0-tve0";
#size-cells = <1>;
ranges;
- osc24M: clk@1c20050 {
+ osc24M: clk-24M {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24000000>;
clock-output-names = "osc24M";
};
- osc32k: clk@0 {
+ osc32k: clk-32k {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
};
};
- soc@1c00000 {
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ /* Address must be kept in the lower 256 MiBs of DRAM for VE. */
+ default-pool {
+ compatible = "shared-dma-pool";
+ size = <0x6000000>;
+ alloc-ranges = <0x40000000 0x10000000>;
+ reusable;
+ linux,cma-default;
+ };
+ };
+
+ soc {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
+ dma-ranges;
ranges;
- sram-controller@1c00000 {
- compatible = "allwinner,sun4i-a10-sram-controller";
+ system-control@1c00000 {
+ compatible = "allwinner,sun5i-a13-system-control";
reg = <0x01c00000 0x30>;
#address-cells = <1>;
#size-cells = <1>;
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x00000000 0xc000>;
- };
- emac_sram: sram-section@8000 {
- compatible = "allwinner,sun4i-a10-sram-a3-a4";
- reg = <0x8000 0x4000>;
- status = "disabled";
+ emac_sram: sram-section@8000 {
+ compatible = "allwinner,sun5i-a13-sram-a3-a4",
+ "allwinner,sun4i-a10-sram-a3-a4";
+ reg = <0x8000 0x4000>;
+ status = "disabled";
+ };
};
sram_d: sram@10000 {
ranges = <0 0x00010000 0x1000>;
otg_sram: sram-section@0 {
- compatible = "allwinner,sun4i-a10-sram-d";
+ compatible = "allwinner,sun5i-a13-sram-d",
+ "allwinner,sun4i-a10-sram-d";
reg = <0x0000 0x1000>;
status = "disabled";
};
};
+
+ sram_c: sram@1d00000 {
+ compatible = "mmio-sram";
+ reg = <0x01d00000 0xd0000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x01d00000 0xd0000>;
+
+ ve_sram: sram-section@0 {
+ compatible = "allwinner,sun5i-a13-sram-c1",
+ "allwinner,sun4i-a10-sram-c1";
+ reg = <0x000000 0x80000>;
+ };
+ };
+ };
+
+ mbus: dram-controller@1c01000 {
+ compatible = "allwinner,sun5i-a13-mbus";
+ reg = <0x01c01000 0x1000>;
+ clocks = <&ccu CLK_MBUS>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ dma-ranges = <0x00000000 0x40000000 0x20000000>;
+ #interconnect-cells = <1>;
};
dma: dma-controller@1c02000 {
#dma-cells = <2>;
};
- nfc: nand@1c03000 {
+ nfc: nand-controller@1c03000 {
compatible = "allwinner,sun4i-a10-nand";
reg = <0x01c03000 0x1000>;
interrupts = <37>;
status = "disabled";
port {
- #address-cells = <1>;
- #size-cells = <0>;
- tve0_in_tcon0: endpoint@0 {
- reg = <0>;
+ tve0_in_tcon0: endpoint {
remote-endpoint = <&tcon0_out_tve0>;
};
};
compatible = "allwinner,sun5i-a13-tcon";
reg = <0x01c0c000 0x1000>;
interrupts = <44>;
+ dmas = <&dma SUN4I_DMA_DEDICATED 14>;
resets = <&ccu RST_LCD>;
reset-names = "lcd";
clocks = <&ccu CLK_AHB_LCD>,
"tcon-ch0",
"tcon-ch1";
clock-output-names = "tcon-pixel-clock";
+ #clock-cells = <0>;
status = "disabled";
ports {
#size-cells = <0>;
tcon0_in: port@0 {
- #address-cells = <1>;
- #size-cells = <0>;
reg = <0>;
- tcon0_in_be0: endpoint@0 {
- reg = <0>;
+ tcon0_in_be0: endpoint {
remote-endpoint = <&be0_out_tcon0>;
};
};
};
};
+ video-codec@1c0e000 {
+ compatible = "allwinner,sun5i-a13-video-engine";
+ reg = <0x01c0e000 0x1000>;
+ clocks = <&ccu CLK_AHB_VE>, <&ccu CLK_VE>,
+ <&ccu CLK_DRAM_VE>;
+ clock-names = "ahb", "mod", "ram";
+ resets = <&ccu RST_VE>;
+ interrupts = <53>;
+ allwinner,sram = <&ve_sram 1>;
+ };
+
mmc0: mmc@1c0f000 {
compatible = "allwinner,sun5i-a13-mmc";
reg = <0x01c0f000 0x1000>;
clocks = <&ccu CLK_AHB_MMC0>, <&ccu CLK_MMC0>;
clock-names = "ahb", "mmc";
interrupts = <32>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
phy-names = "usb";
extcon = <&usbphy 0>;
allwinner,sram = <&otg_sram 1>;
+ dr_mode = "otg";
status = "disabled";
};
usbphy: phy@1c13400 {
#phy-cells = <1>;
compatible = "allwinner,sun5i-a13-usb-phy";
- reg = <0x01c13400 0x10 0x01c14800 0x4>;
+ reg = <0x01c13400 0x10>, <0x01c14800 0x4>;
reg-names = "phy_ctrl", "pmu1";
clocks = <&ccu CLK_USB_PHY0>;
clock-names = "usb_phy";
#interrupt-cells = <3>;
#gpio-cells = <3>;
- emac_pins_a: emac0@0 {
+ emac_pd_pins: emac-pd-pins {
pins = "PD6", "PD7", "PD10",
"PD11", "PD12", "PD13", "PD14",
"PD15", "PD18", "PD19", "PD20",
function = "emac";
};
- i2c0_pins_a: i2c0@0 {
+ i2c0_pins: i2c0-pins {
pins = "PB0", "PB1";
function = "i2c0";
};
- i2c1_pins_a: i2c1@0 {
+ i2c1_pins: i2c1-pins {
pins = "PB15", "PB16";
function = "i2c1";
};
- i2c2_pins_a: i2c2@0 {
+ i2c2_pins: i2c2-pins {
pins = "PB17", "PB18";
function = "i2c2";
};
- ir0_rx_pins_a: ir0@0 {
+ ir0_rx_pin: ir0-rx-pin {
pins = "PB4";
function = "ir0";
};
- lcd_rgb565_pins: lcd_rgb565@0 {
+ lcd_rgb565_pins: lcd-rgb565-pins {
pins = "PD3", "PD4", "PD5", "PD6", "PD7",
"PD10", "PD11", "PD12", "PD13", "PD14", "PD15",
"PD19", "PD20", "PD21", "PD22", "PD23",
function = "lcd0";
};
- lcd_rgb666_pins: lcd_rgb666@0 {
+ lcd_rgb666_pins: lcd-rgb666-pins {
pins = "PD2", "PD3", "PD4", "PD5", "PD6", "PD7",
"PD10", "PD11", "PD12", "PD13", "PD14", "PD15",
"PD18", "PD19", "PD20", "PD21", "PD22", "PD23",
function = "lcd0";
};
- mmc0_pins_a: mmc0@0 {
+ mmc0_pins: mmc0-pins {
pins = "PF0", "PF1", "PF2", "PF3",
"PF4", "PF5";
function = "mmc0";
bias-pull-up;
};
- mmc2_pins_a: mmc2@0 {
+ mmc2_4bit_pc_pins: mmc2-4bit-pc-pins {
pins = "PC6", "PC7", "PC8", "PC9",
- "PC10", "PC11", "PC12", "PC13",
- "PC14", "PC15";
+ "PC10", "PC11";
function = "mmc2";
drive-strength = <30>;
bias-pull-up;
};
- mmc2_4bit_pins_a: mmc2-4bit@0 {
+ mmc2_8bit_pins: mmc2-8bit-pins {
pins = "PC6", "PC7", "PC8", "PC9",
- "PC10", "PC11";
+ "PC10", "PC11", "PC12", "PC13",
+ "PC14", "PC15";
function = "mmc2";
drive-strength = <30>;
bias-pull-up;
};
- nand_pins_a: nand-base0@0 {
+ nand_pins: nand-pins {
pins = "PC0", "PC1", "PC2",
"PC5", "PC8", "PC9", "PC10",
"PC11", "PC12", "PC13", "PC14",
function = "nand0";
};
- nand_cs0_pins_a: nand-cs@0 {
+ nand_cs0_pin: nand-cs0-pin {
pins = "PC4";
function = "nand0";
};
- nand_rb0_pins_a: nand-rb@0 {
+ nand_rb0_pin: nand-rb0-pin {
pins = "PC6";
function = "nand0";
};
- spi2_pins_a: spi2@0 {
+ pwm0_pin: pwm0-pin {
+ pins = "PB2";
+ function = "pwm";
+ };
+
+ spi2_pe_pins: spi2-pe-pins {
pins = "PE1", "PE2", "PE3";
function = "spi2";
};
- spi2_cs0_pins_a: spi2-cs0@0 {
+ spi2_cs0_pe_pin: spi2-cs0-pe-pin {
pins = "PE0";
function = "spi2";
};
- uart1_pins_a: uart1@0 {
+ uart1_pe_pins: uart1-pe-pins {
pins = "PE10", "PE11";
function = "uart1";
};
- uart1_pins_b: uart1@1 {
+ uart1_pg_pins: uart1-pg-pins {
pins = "PG3", "PG4";
function = "uart1";
};
- uart2_pins_a: uart2@0 {
+ uart2_pd_pins: uart2-pd-pins {
pins = "PD2", "PD3";
function = "uart2";
};
- uart2_cts_rts_pins_a: uart2-cts-rts@0 {
+ uart2_cts_rts_pd_pins: uart2-cts-rts-pd-pins {
pins = "PD4", "PD5";
function = "uart2";
};
- uart3_pins_a: uart3@0 {
+ uart3_pg_pins: uart3-pg-pins {
pins = "PG9", "PG10";
function = "uart3";
};
- uart3_cts_rts_pins_a: uart3-cts-rts@0 {
+ uart3_cts_rts_pg_pins: uart3-cts-rts-pg-pins {
pins = "PG11", "PG12";
function = "uart3";
};
-
- pwm0_pins: pwm0 {
- pins = "PB2";
- function = "pwm";
- };
};
timer@1c20c00 {
compatible = "allwinner,sun4i-a10-timer";
reg = <0x01c20c00 0x90>;
- interrupts = <22>;
+ interrupts = <22>,
+ <23>,
+ <24>,
+ <25>,
+ <67>,
+ <68>;
clocks = <&ccu CLK_HOSC>;
};
wdt: watchdog@1c20c90 {
compatible = "allwinner,sun4i-a10-wdt";
reg = <0x01c20c90 0x10>;
+ interrupts = <24>;
+ clocks = <&osc24M>;
};
ir0: ir@1c21800 {
reg = <0x01c2ac00 0x400>;
interrupts = <7>;
clocks = <&ccu CLK_APB1_I2C0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x01c2b000 0x400>;
interrupts = <8>;
clocks = <&ccu CLK_APB1_I2C1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x01c2b400 0x400>;
interrupts = <9>;
clocks = <&ccu CLK_APB1_I2C2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
+ mali: gpu@1c40000 {
+ compatible = "allwinner,sun4i-a10-mali", "arm,mali-400";
+ reg = <0x01c40000 0x10000>;
+ interrupts = <69>, <70>, <71>, <72>, <73>;
+ interrupt-names = "gp", "gpmmu", "pp0", "ppmmu0", "pmu";
+ clocks = <&ccu CLK_AHB_GPU>, <&ccu CLK_GPU>;
+ clock-names = "bus", "core";
+ resets = <&ccu RST_GPU>;
+ assigned-clocks = <&ccu CLK_GPU>;
+ assigned-clock-rates = <320000000>;
+ };
+
timer@1c60000 {
compatible = "allwinner,sun5i-a13-hstimer";
reg = <0x01c60000 0x1000>;
clock-names = "ahb", "mod",
"ram";
resets = <&ccu RST_DE_FE>;
+ interconnects = <&mbus 19>;
+ interconnect-names = "dma-mem";
status = "disabled";
ports {
#size-cells = <0>;
fe0_out: port@1 {
- #address-cells = <1>;
- #size-cells = <0>;
reg = <1>;
- fe0_out_be0: endpoint@0 {
- reg = <0>;
+ fe0_out_be0: endpoint {
remote-endpoint = <&be0_in_fe0>;
};
};
clock-names = "ahb", "mod",
"ram";
resets = <&ccu RST_DE_BE>;
+ interconnects = <&mbus 18>;
+ interconnect-names = "dma-mem";
status = "disabled";
- assigned-clocks = <&ccu CLK_DE_BE>;
- assigned-clock-rates = <300000000>;
-
ports {
#address-cells = <1>;
#size-cells = <0>;
be0_in: port@0 {
- #address-cells = <1>;
- #size-cells = <0>;
reg = <0>;
- be0_in_fe0: endpoint@0 {
- reg = <0>;
+ be0_in_fe0: endpoint {
remote-endpoint = <&fe0_out_be0>;
};
};
be0_out: port@1 {
- #address-cells = <1>;
- #size-cells = <0>;
reg = <1>;
- be0_out_tcon0: endpoint@0 {
- reg = <0>;
+ be0_out_tcon0: endpoint {
remote-endpoint = <&tcon0_in_be0>;
};
};
status = "okay";
};
-&pio {
- usb1_vbus_pin_a: usb1_vbus_pin@0 {
- pins = "PH27";
- function = "gpio_out";
- };
-};
-
®_usb1_vbus {
- pinctrl-0 = <&usb1_vbus_pin_a>;
gpio = <&pio 7 27 GPIO_ACTIVE_HIGH>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_ph_pins>;
status = "okay";
};
stdout-path = "serial0:115200n8";
};
- i2c_lcd: i2c@0 {
+ i2c_lcd: i2c {
/* The lcd panel i2c interface is hooked up via gpios */
compatible = "i2c-gpio";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c_lcd_pins>;
- gpios = <&pio 0 23 GPIO_ACTIVE_HIGH>, /* PA23, sda */
- <&pio 0 24 GPIO_ACTIVE_HIGH>; /* PA24, scl */
+ sda-gpios = <&pio 0 23 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PA23 */
+ scl-gpios = <&pio 0 24 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PA24 */
i2c-gpio,delay-us = <5>;
};
};
&gmac {
pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_rgmii_a>;
- phy = <&phy1>;
+ pinctrl-0 = <&gmac_rgmii_pins>;
+ phy-handle = <&phy1>;
phy-mode = "rgmii";
status = "okay";
-
- phy1: ethernet-phy@1 {
- reg = <1>;
- };
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "fail";
};
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
};
&i2c2 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
mma8452: mma8452@1d {
};
};
+&mdio {
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_colombus>;
vmmc-supply = <®_vcc3v0>;
bus-width = <4>;
cd-gpios = <&pio 0 8 GPIO_ACTIVE_LOW>; /* PA8 */
status = "okay";
};
-&mmc0_pins_a {
- bias-pull-up;
-};
-
-&pio {
- mmc0_cd_pin_colombus: mmc0_cd_pin@0 {
- pins = "PA8";
- function = "gpio_in";
- bias-pull-up;
- };
-
- usb2_vbus_pin_colombus: usb2_vbus_pin@0 {
- pins = "PH24";
- function = "gpio_out";
- };
-
- i2c_lcd_pins: i2c_lcd_pin@0 {
- pins = "PA23", "PA24";
- function = "gpio_out";
- bias-pull-up;
- };
-};
-
®_usb2_vbus {
- pinctrl-names = "default";
- pinctrl-0 = <&usb2_vbus_pin_colombus>;
gpio = <&pio 7 24 GPIO_ACTIVE_HIGH>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_ph_pins>;
status = "okay";
};
vga-dac {
compatible = "dumb-vga-dac";
vdd-supply = <®_vga_3v3>;
- #address-cells = <1>;
- #size-cells = <0>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
- #address-cells = <1>;
- #size-cells = <0>;
reg = <0>;
- vga_dac_in: endpoint@0 {
- reg = <0>;
+ vga_dac_in: endpoint {
remote-endpoint = <&tcon0_out_vga>;
};
};
port@1 {
- #address-cells = <1>;
- #size-cells = <0>;
reg = <1>;
- vga_dac_out: endpoint@0 {
- reg = <0>;
+ vga_dac_out: endpoint {
remote-endpoint = <&vga_con_in>;
};
};
&gmac {
pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_rgmii_a>, <&gmac_phy_reset_pin_hummingbird>;
- phy = <&phy1>;
+ pinctrl-0 = <&gmac_rgmii_pins>;
+ phy-handle = <&phy1>;
phy-mode = "rgmii-id";
- snps,reset-gpio = <&pio 0 21 GPIO_ACTIVE_HIGH>;
- snps,reset-active-low;
- snps,reset-delays-us = <0 10000 30000>;
status = "okay";
-
- phy1: ethernet-phy@1 {
- reg = <1>;
- };
};
&hdmi {
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
/* pull-ups and devices require AXP221 DLDO3 */
status = "failed";
};
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
};
&i2c2 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
pcf8563: rtc@51 {
&ir {
pinctrl-names = "default";
- pinctrl-0 = <&ir_pins_a>;
+ pinctrl-0 = <&s_ir_rx_pin>;
status = "okay";
};
+&mdio {
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ reset-gpios = <&pio 0 21 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <30000>;
+ };
+};
+
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_hummingbird>;
vmmc-supply = <®_dcdc1>;
bus-width = <4>;
cd-gpios = <&pio 0 8 GPIO_ACTIVE_LOW>; /* PA8 */
status = "okay";
};
-&mmc0_pins_a {
- /* external pull-ups missing for some pins */
- bias-pull-up;
-};
-
&mmc1 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc1_pins_a>, <&wifi_reset_pin_hummingbird>;
vmmc-supply = <®_aldo1>;
mmc-pwrseq = <&wifi_pwrseq>;
bus-width = <4>;
status = "okay";
};
-&pio {
- gmac_phy_reset_pin_hummingbird: gmac_phy_reset_pin@0 {
- pins = "PA21";
- function = "gpio_out";
- };
-
- mmc0_cd_pin_hummingbird: mmc0_cd_pin@0 {
- pins = "PA8";
- function = "gpio_in";
- bias-pull-up;
- };
-
- wifi_reset_pin_hummingbird: wifi_reset_pin@0 {
- pins = "PG10";
- function = "gpio_out";
- };
-};
-
&p2wi {
status = "okay";
axp22x: pmic@68 {
compatible = "x-powers,axp221";
reg = <0x68>;
- interrupt-parent = <&nmi_intc>;
+ interrupt-parent = <&r_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
x-powers,drive-vbus-en;
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_ph_pins>;
status = "okay";
};
};
&usbphy {
- usb0_id_det-gpio = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15 */
- usb0_vbus_det-gpio = <&pio 0 16 GPIO_ACTIVE_HIGH>; /* PA16 */
+ usb0_id_det-gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15 */
+ usb0_vbus_det-gpios = <&pio 0 16 GPIO_ACTIVE_HIGH>; /* PA16 */
usb0_vbus_power-supply = <&usb_power_supply>;
usb0_vbus-supply = <®_drivevbus>;
usb1_vbus-supply = <®_usb1_vbus>;
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins_i7>;
- blue {
+ led {
label = "i7:blue:usr";
gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>;
};
&gmac {
pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_mii_a>;
- phy = <&phy1>;
+ pinctrl-0 = <&gmac_mii_pins>;
+ phy-handle = <&phy1>;
phy-mode = "mii";
status = "okay";
-
- phy1: ethernet-phy@1 {
- reg = <1>;
- };
};
&hdmi {
&ir {
pinctrl-names = "default";
- pinctrl-0 = <&ir_pins_a>;
+ pinctrl-0 = <&s_ir_rx_pin>;
status = "okay";
};
+&mdio {
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_i7>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 22 GPIO_ACTIVE_LOW>; /* PH22 */
status = "okay";
};
-&pio {
- led_pins_i7: led_pins@0 {
- pins = "PH13";
- function = "gpio_out";
- };
-
- mmc0_cd_pin_i7: mmc0_cd_pin@0 {
- pins = "PH22";
- function = "gpio_in";
- bias-pull-up;
- };
-
- usb1_vbus_pin_i7: usb1_vbus_pin@0 {
- pins = "PC27";
- function = "gpio_out";
- };
-};
-
®_usb1_vbus {
- pinctrl-names = "default";
- pinctrl-0 = <&usb1_vbus_pin_i7>;
gpio = <&pio 2 27 GPIO_ACTIVE_HIGH>;
status = "okay";
};
&spdif {
pinctrl-names = "default";
- pinctrl-0 = <&spdif_pins_a>;
- spdif-out = "okay";
+ pinctrl-0 = <&spdif_tx_pin>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_ph_pins>;
status = "okay";
};
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins_m9>;
- blue {
+ led {
label = "m9:blue:pwr";
gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>;
default-state = "on";
&gmac {
pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_mii_a>;
- phy = <&phy1>;
+ pinctrl-0 = <&gmac_mii_pins>;
+ phy-handle = <&phy1>;
phy-mode = "mii";
phy-supply = <®_dldo1>;
status = "okay";
-
- phy1: ethernet-phy@1 {
- reg = <1>;
- };
};
&ir {
pinctrl-names = "default";
- pinctrl-0 = <&ir_pins_a>;
+ pinctrl-0 = <&s_ir_rx_pin>;
status = "okay";
};
+&mdio {
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_m9>;
vmmc-supply = <®_dcdc1>;
bus-width = <4>;
cd-gpios = <&pio 7 22 GPIO_ACTIVE_LOW>; /* PH22 */
axp22x: pmic@68 {
compatible = "x-powers,axp221";
reg = <0x68>;
- interrupt-parent = <&nmi_intc>;
+ interrupt-parent = <&r_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
};
};
#include "axp22x.dtsi"
-&pio {
- led_pins_m9: led_pins@0 {
- pins = "PH13";
- function = "gpio_out";
- };
-
- mmc0_cd_pin_m9: mmc0_cd_pin@0 {
- pins = "PH22";
- function = "gpio_in";
- bias-pull-up;
- };
-
- usb1_vbus_pin_m9: usb1_vbus_pin@0 {
- pins = "PC27";
- function = "gpio_out";
- };
-};
-
®_aldo1 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
®_usb1_vbus {
- pinctrl-names = "default";
- pinctrl-0 = <&usb1_vbus_pin_m9>;
gpio = <&pio 2 27 GPIO_ACTIVE_HIGH>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_ph_pins>;
status = "okay";
};
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins_m9>;
- blue {
+ led {
label = "a1000g:blue:pwr";
gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>;
default-state = "on";
&gmac {
pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_mii_a>;
- phy = <&phy1>;
+ pinctrl-0 = <&gmac_mii_pins>;
+ phy-handle = <&phy1>;
phy-mode = "mii";
phy-supply = <®_dldo1>;
status = "okay";
-
- phy1: ethernet-phy@1 {
- reg = <1>;
- };
};
&ir {
pinctrl-names = "default";
- pinctrl-0 = <&ir_pins_a>;
+ pinctrl-0 = <&s_ir_rx_pin>;
status = "okay";
};
+&mdio {
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_m9>;
vmmc-supply = <®_dcdc1>;
bus-width = <4>;
cd-gpios = <&pio 7 22 GPIO_ACTIVE_LOW>; /* PH22 */
axp22x: pmic@68 {
compatible = "x-powers,axp221";
reg = <0x68>;
- interrupt-parent = <&nmi_intc>;
+ interrupt-parent = <&r_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
};
};
#include "axp22x.dtsi"
-&pio {
- led_pins_m9: led_pins@0 {
- pins = "PH13";
- function = "gpio_out";
- };
-
- mmc0_cd_pin_m9: mmc0_cd_pin@0 {
- pins = "PH22";
- function = "gpio_in";
- bias-pull-up;
- };
-
- usb1_vbus_pin_m9: usb1_vbus_pin@0 {
- pins = "PC27";
- function = "gpio_out";
- };
-};
-
®_aldo1 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
®_usb1_vbus {
- pinctrl-names = "default";
- pinctrl-0 = <&usb1_vbus_pin_m9>;
gpio = <&pio 2 27 GPIO_ACTIVE_HIGH>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_ph_pins>;
status = "okay";
};
&gmac {
pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_rgmii_a>;
+ pinctrl-0 = <&gmac_rgmii_pins>;
phy = <&phy1>;
phy-mode = "rgmii";
status = "okay";
+};
+&mdio {
phy1: ethernet-phy@1 {
reg = <1>;
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_ph_pins>;
status = "okay";
};
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#include "skeleton.dtsi"
-
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/thermal/thermal.h>
/ {
interrupt-parent = <&gic>;
+ #address-cells = <1>;
+ #size-cells = <1>;
aliases {
ethernet0 = &gmac;
#size-cells = <1>;
ranges;
- simplefb_hdmi: framebuffer@0 {
+ simplefb_hdmi: framebuffer-lcd0-hdmi {
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0-hdmi";
status = "disabled";
};
- simplefb_lcd: framebuffer@1 {
+ simplefb_lcd: framebuffer-lcd0 {
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0";
reg = <0>;
clocks = <&ccu CLK_CPU>;
clock-latency = <244144>; /* 8 32k periods */
- operating-points = <
+ operating-points =
/* kHz uV */
- 1008000 1200000
- 864000 1200000
- 720000 1100000
- 480000 1000000
- >;
+ <1008000 1200000>,
+ <864000 1200000>,
+ <720000 1100000>,
+ <480000 1000000>;
#cooling-cells = <2>;
};
- cpu@1 {
+ cpu1: cpu@1 {
compatible = "arm,cortex-a7";
device_type = "cpu";
reg = <1>;
+ clocks = <&ccu CLK_CPU>;
+ clock-latency = <244144>; /* 8 32k periods */
+ operating-points =
+ /* kHz uV */
+ <1008000 1200000>,
+ <864000 1200000>,
+ <720000 1100000>,
+ <480000 1000000>;
+ #cooling-cells = <2>;
};
- cpu@2 {
+ cpu2: cpu@2 {
compatible = "arm,cortex-a7";
device_type = "cpu";
reg = <2>;
+ clocks = <&ccu CLK_CPU>;
+ clock-latency = <244144>; /* 8 32k periods */
+ operating-points =
+ /* kHz uV */
+ <1008000 1200000>,
+ <864000 1200000>,
+ <720000 1100000>,
+ <480000 1000000>;
+ #cooling-cells = <2>;
};
- cpu@3 {
+ cpu3: cpu@3 {
compatible = "arm,cortex-a7";
device_type = "cpu";
reg = <3>;
+ clocks = <&ccu CLK_CPU>;
+ clock-latency = <244144>; /* 8 32k periods */
+ operating-points =
+ /* kHz uV */
+ <1008000 1200000>,
+ <864000 1200000>,
+ <720000 1100000>,
+ <480000 1000000>;
+ #cooling-cells = <2>;
};
};
thermal-zones {
- cpu_thermal {
+ cpu-thermal {
/* milliseconds */
polling-delay-passive = <250>;
polling-delay = <1000>;
cooling-maps {
map0 {
trip = <&cpu_alert0>;
- cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
};
};
};
- memory {
- reg = <0x40000000 0x80000000>;
- };
-
pmu {
- compatible = "arm,cortex-a7-pmu", "arm,cortex-a15-pmu";
+ compatible = "arm,cortex-a7-pmu";
interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
#size-cells = <1>;
ranges;
- osc24M: osc24M {
+ osc24M: clk-24M {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24000000>;
+ clock-accuracy = <50000>;
+ clock-output-names = "osc24M";
};
- osc32k: clk@0 {
+ osc32k: clk-32k {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
- clock-output-names = "osc32k";
+ clock-accuracy = <50000>;
+ clock-output-names = "ext_osc32k";
};
/*
* The actual TX clock rate is not controlled by the
* gmac_tx clock.
*/
- mii_phy_tx_clk: clk@1 {
+ mii_phy_tx_clk: clk-mii-phy-tx {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <25000000>;
clock-output-names = "mii_phy_tx";
};
- gmac_int_tx_clk: clk@2 {
+ gmac_int_tx_clk: clk-gmac-int-tx {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <125000000>;
status = "disabled";
};
- soc@1c00000 {
+ soc {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
compatible = "allwinner,sun6i-a31-tcon";
reg = <0x01c0c000 0x1000>;
interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
- resets = <&ccu RST_AHB1_LCD0>;
- reset-names = "lcd";
+ dmas = <&dma 11>;
+ resets = <&ccu RST_AHB1_LCD0>,
+ <&ccu RST_AHB1_LVDS>;
+ reset-names = "lcd",
+ "lvds";
clocks = <&ccu CLK_AHB1_LCD0>,
<&ccu CLK_LCD0_CH0>,
- <&ccu CLK_LCD0_CH1>;
+ <&ccu CLK_LCD0_CH1>,
+ <&ccu 15>;
clock-names = "ahb",
"tcon-ch0",
- "tcon-ch1";
+ "tcon-ch1",
+ "lvds-alt";
clock-output-names = "tcon0-pixel-clock";
+ #clock-cells = <0>;
ports {
#address-cells = <1>;
compatible = "allwinner,sun6i-a31-tcon";
reg = <0x01c0d000 0x1000>;
interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
- resets = <&ccu RST_AHB1_LCD1>;
- reset-names = "lcd";
+ dmas = <&dma 12>;
+ resets = <&ccu RST_AHB1_LCD1>,
+ <&ccu RST_AHB1_LVDS>;
+ reset-names = "lcd", "lvds";
clocks = <&ccu CLK_AHB1_LCD1>,
<&ccu CLK_LCD1_CH0>,
- <&ccu CLK_LCD1_CH1>;
+ <&ccu CLK_LCD1_CH1>,
+ <&ccu 15>;
clock-names = "ahb",
"tcon-ch0",
- "tcon-ch1";
+ "tcon-ch1",
+ "lvds-alt";
clock-output-names = "tcon1-pixel-clock";
+ #clock-cells = <0>;
ports {
#address-cells = <1>;
resets = <&ccu RST_AHB1_MMC0>;
reset-names = "ahb";
interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
resets = <&ccu RST_AHB1_MMC1>;
reset-names = "ahb";
interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
<&ccu CLK_PLL_VIDEO1_2X>;
clock-names = "ahb", "mod", "ddc", "pll-0", "pll-1";
resets = <&ccu RST_AHB1_HDMI>;
- reset-names = "ahb";
dma-names = "ddc-tx", "ddc-rx", "audio-tx";
dmas = <&dma 13>, <&dma 13>, <&dma 14>;
status = "disabled";
};
hdmi_out: port@1 {
- #address-cells = <1>;
- #size-cells = <0>;
reg = <1>;
};
};
phys = <&usbphy 0>;
phy-names = "usb";
extcon = <&usbphy 0>;
+ dr_mode = "otg";
status = "disabled";
};
ccu: clock@1c20000 {
compatible = "allwinner,sun6i-a31-ccu";
reg = <0x01c20000 0x400>;
- clocks = <&osc24M>, <&osc32k>;
+ clocks = <&osc24M>, <&rtc 0>;
clock-names = "hosc", "losc";
#clock-cells = <1>;
#reset-cells = <1>;
<GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_APB1_PIO>, <&osc24M>, <&osc32k>;
+ clocks = <&ccu CLK_APB1_PIO>, <&osc24M>, <&rtc 0>;
clock-names = "apb", "hosc", "losc";
gpio-controller;
interrupt-controller;
#interrupt-cells = <3>;
#gpio-cells = <3>;
- gmac_pins_gmii_a: gmac_gmii@0 {
+ gmac_gmii_pins: gmac-gmii-pins {
pins = "PA0", "PA1", "PA2", "PA3",
"PA4", "PA5", "PA6", "PA7",
"PA8", "PA9", "PA10", "PA11",
drive-strength = <30>;
};
- gmac_pins_mii_a: gmac_mii@0 {
+ gmac_mii_pins: gmac-mii-pins {
pins = "PA0", "PA1", "PA2", "PA3",
"PA8", "PA9", "PA11",
"PA12", "PA13", "PA14", "PA19",
function = "gmac";
};
- gmac_pins_rgmii_a: gmac_rgmii@0 {
+ gmac_rgmii_pins: gmac-rgmii-pins {
pins = "PA0", "PA1", "PA2", "PA3",
"PA9", "PA10", "PA11",
"PA12", "PA13", "PA14", "PA19",
drive-strength = <40>;
};
- i2c0_pins_a: i2c0@0 {
+ i2c0_pins: i2c0-pins {
pins = "PH14", "PH15";
function = "i2c0";
};
- i2c1_pins_a: i2c1@0 {
+ i2c1_pins: i2c1-pins {
pins = "PH16", "PH17";
function = "i2c1";
};
- i2c2_pins_a: i2c2@0 {
+ i2c2_pins: i2c2-pins {
pins = "PH18", "PH19";
function = "i2c2";
};
- lcd0_rgb888_pins: lcd0_rgb888 {
+ lcd0_rgb888_pins: lcd0-rgb888-pins {
pins = "PD0", "PD1", "PD2", "PD3",
"PD4", "PD5", "PD6", "PD7",
"PD8", "PD9", "PD10", "PD11",
function = "lcd0";
};
- mmc0_pins_a: mmc0@0 {
+ mmc0_pins: mmc0-pins {
pins = "PF0", "PF1", "PF2",
"PF3", "PF4", "PF5";
function = "mmc0";
bias-pull-up;
};
- mmc1_pins_a: mmc1@0 {
+ mmc1_pins: mmc1-pins {
pins = "PG0", "PG1", "PG2", "PG3",
"PG4", "PG5";
function = "mmc1";
bias-pull-up;
};
- mmc2_pins_a: mmc2@0 {
+ mmc2_4bit_pins: mmc2-4bit-pins {
pins = "PC6", "PC7", "PC8", "PC9",
"PC10", "PC11";
function = "mmc2";
bias-pull-up;
};
- mmc2_8bit_emmc_pins: mmc2@1 {
+ mmc2_8bit_emmc_pins: mmc2-8bit-emmc-pins {
pins = "PC6", "PC7", "PC8", "PC9",
"PC10", "PC11", "PC12",
"PC13", "PC14", "PC15",
bias-pull-up;
};
- mmc3_8bit_emmc_pins: mmc3@1 {
+ mmc3_8bit_emmc_pins: mmc3-8bit-emmc-pins {
pins = "PC6", "PC7", "PC8", "PC9",
"PC10", "PC11", "PC12",
"PC13", "PC14", "PC15",
bias-pull-up;
};
- spdif_pins_a: spdif@0 {
+ spdif_tx_pin: spdif-tx-pin {
pins = "PH28";
function = "spdif";
};
- uart0_pins_a: uart0@0 {
+ uart0_ph_pins: uart0-ph-pins {
pins = "PH20", "PH21";
function = "uart0";
};
<GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+ <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&osc24M>;
};
wdt1: watchdog@1c20ca0 {
compatible = "allwinner,sun6i-a31-wdt";
reg = <0x01c20ca0 0x20>;
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&osc24M>;
};
spdif: spdif@1c21000 {
interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_APB2_I2C0>;
resets = <&ccu RST_APB2_I2C0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_APB2_I2C1>;
resets = <&ccu RST_APB2_I2C1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_APB2_I2C2>;
resets = <&ccu RST_APB2_I2C2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
snps,fixed-burst;
snps,force_sf_dma_mode;
status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
+
+ mdio: mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
};
crypto: crypto-engine@1c15000 {
dma-names = "rx", "tx";
resets = <&ccu RST_AHB1_SPI0>;
status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
};
spi1: spi@1c69000 {
dma-names = "rx", "tx";
resets = <&ccu RST_AHB1_SPI1>;
status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
};
spi2: spi@1c6a000 {
dma-names = "rx", "tx";
resets = <&ccu RST_AHB1_SPI2>;
status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
};
spi3: spi@1c6b000 {
dma-names = "rx", "tx";
resets = <&ccu RST_AHB1_SPI3>;
status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
};
gic: interrupt-controller@1c81000 {
- compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
+ compatible = "arm,gic-400";
reg = <0x01c81000 0x1000>,
<0x01c82000 0x2000>,
<0x01c84000 0x2000>,
"ram";
resets = <&ccu RST_AHB1_BE1>;
- assigned-clocks = <&ccu CLK_BE1>;
- assigned-clock-rates = <300000000>;
-
ports {
#address-cells = <1>;
#size-cells = <0>;
"ram";
resets = <&ccu RST_AHB1_DRC1>;
- assigned-clocks = <&ccu CLK_IEP_DRC1>;
- assigned-clock-rates = <300000000>;
-
ports {
#address-cells = <1>;
#size-cells = <0>;
"ram";
resets = <&ccu RST_AHB1_BE0>;
- assigned-clocks = <&ccu CLK_BE0>;
- assigned-clock-rates = <300000000>;
-
ports {
#address-cells = <1>;
#size-cells = <0>;
};
be0_out: port@1 {
- #address-cells = <1>;
- #size-cells = <0>;
reg = <1>;
- be0_out_drc0: endpoint@0 {
- reg = <0>;
+ be0_out_drc0: endpoint {
remote-endpoint = <&drc0_in_be0>;
};
};
"ram";
resets = <&ccu RST_AHB1_DRC0>;
- assigned-clocks = <&ccu CLK_IEP_DRC0>;
- assigned-clock-rates = <300000000>;
-
ports {
#address-cells = <1>;
#size-cells = <0>;
drc0_in: port@0 {
- #address-cells = <1>;
- #size-cells = <0>;
reg = <0>;
- drc0_in_be0: endpoint@0 {
- reg = <0>;
+ drc0_in_be0: endpoint {
remote-endpoint = <&be0_out_drc0>;
};
};
};
rtc: rtc@1f00000 {
+ #clock-cells = <1>;
compatible = "allwinner,sun6i-a31-rtc";
reg = <0x01f00000 0x54>;
interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&osc32k>;
+ clock-output-names = "osc32k";
};
- nmi_intc: interrupt-controller@1f00c00 {
+ r_intc: interrupt-controller@1f00c00 {
compatible = "allwinner,sun6i-a31-r-intc";
interrupt-controller;
#interrupt-cells = <2>;
ar100: ar100_clk {
compatible = "allwinner,sun6i-a31-ar100-clk";
#clock-cells = <0>;
- clocks = <&osc32k>, <&osc24M>,
+ clocks = <&rtc 0>, <&osc24M>,
<&ccu CLK_PLL_PERIPH>,
<&ccu CLK_PLL_PERIPH>;
clock-output-names = "ar100";
ir_clk: ir_clk {
#clock-cells = <0>;
compatible = "allwinner,sun4i-a10-mod0-clk";
- clocks = <&osc32k>, <&osc24M>;
+ clocks = <&rtc 0>, <&osc24M>;
clock-output-names = "ir";
};
};
ir: ir@1f02000 {
- compatible = "allwinner,sun5i-a13-ir";
+ compatible = "allwinner,sun6i-a31-ir";
clocks = <&apb0_gates 1>, <&ir_clk>;
clock-names = "apb", "ir";
resets = <&apb0_rst 1>;
reg = <0x01f02c00 0x400>;
interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&apb0_gates 0>, <&osc24M>, <&osc32k>;
+ clocks = <&apb0_gates 0>, <&osc24M>, <&rtc 0>;
clock-names = "apb", "hosc", "losc";
resets = <&apb0_rst 0>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <3>;
- #size-cells = <0>;
#gpio-cells = <3>;
- ir_pins_a: ir@0 {
+ s_ir_rx_pin: s-ir-rx-pin {
pins = "PL4";
function = "s_ir";
};
- p2wi_pins: p2wi {
+ s_p2wi_pins: s-p2wi-pins {
pins = "PL0", "PL1";
function = "s_p2wi";
};
clock-frequency = <100000>;
resets = <&apb0_rst 3>;
pinctrl-names = "default";
- pinctrl-0 = <&p2wi_pins>;
+ pinctrl-0 = <&s_p2wi_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
vref-supply = <®_aldo3>;
status = "okay";
- button@1000 {
+ button-1000 {
label = "Home";
linux,code = <KEY_HOMEPAGE>;
channel = <0>;
&gmac {
pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_mii_a>;
- phy = <&phy1>;
+ pinctrl-0 = <&gmac_mii_pins>;
+ phy-handle = <&phy1>;
phy-mode = "mii";
status = "okay";
- phy1: ethernet-phy@1 {
- reg = <1>;
- };
};
&ir {
pinctrl-names = "default";
- pinctrl-0 = <&ir_pins_a>;
+ pinctrl-0 = <&s_ir_rx_pin>;
status = "okay";
};
+&mdio {
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
&ohci1 {
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_ph_pins>;
status = "okay";
};
};
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
ft5406ee8: touchscreen@38 {
vref-supply = <®_aldo3>;
status = "okay";
- button@200 {
+ button-200 {
label = "Volume Down";
linux,code = <KEY_VOLUMEDOWN>;
channel = <0>;
voltage = <200000>;
};
- button@900 {
+ button-900 {
label = "Volume Up";
linux,code = <KEY_VOLUMEUP>;
channel = <0>;
voltage = <900000>;
};
- button@1200 {
+ button-1200 {
label = "Back";
linux,code = <KEY_BACK>;
channel = <0>;
&i2c0 {
/* pull-ups and device VDDIO use AXP221 DLDO3 */
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "failed";
};
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
ctp@5d {
- pinctrl-names = "default";
- pinctrl-0 = <>911_int_primo81>;
compatible = "goodix,gt911";
reg = <0x5d>;
interrupt-parent = <&pio>;
};
&i2c2 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
accelerometer@1c {
reg = <0x1c>;
interrupt-parent = <&pio>;
interrupts = <0 9 IRQ_TYPE_LEVEL_HIGH>; /* PA9 */
- #io-channel-cells = <1>;
};
};
vref-supply = <®_aldo3>;
status = "okay";
- button@158 {
+ button-158 {
label = "Volume Up";
linux,code = <KEY_VOLUMEUP>;
channel = <0>;
voltage = <158730>;
};
- button@349 {
+ button-349 {
label = "Volume Down";
linux,code = <KEY_VOLUMEDOWN>;
channel = <0>;
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_primo81>;
vmmc-supply = <®_dcdc1>;
bus-width = <4>;
cd-gpios = <&pio 0 8 GPIO_ACTIVE_LOW>; /* PA8 */
};
&pio {
- gt911_int_primo81: gt911_int_pin@0 {
- pins = "PA3";
- function = "gpio_in";
- };
-
- mma8452_int_primo81: mma8452_int_pin@0 {
+ mma8452_int_primo81: mma8452-int-pin {
pins = "PA9";
function = "gpio_in";
bias-pull-up;
};
-
- mmc0_cd_pin_primo81: mmc0_cd_pin@0 {
- pins = "PA8";
- function = "gpio_in";
- bias-pull-up;
- };
};
&p2wi {
axp22x: pmic@68 {
compatible = "x-powers,axp221";
reg = <0x68>;
- interrupt-parent = <&nmi_intc>;
+ interrupt-parent = <&r_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
x-powers,drive-vbus-en;
};
};
&usbphy {
- usb0_id_det-gpio = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15 */
+ usb0_id_det-gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15 */
usb0_vbus_power-supply = <&usb_power_supply>;
usb0_vbus-supply = <®_drivevbus>;
usb1_vbus-supply = <®_dldo1>;
axp22x: pmic@68 {
compatible = "x-powers,axp221";
reg = <0x68>;
- interrupt-parent = <&nmi_intc>;
+ interrupt-parent = <&r_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
};
};
/* UART0 pads available on core board */
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_ph_pins>;
status = "okay";
};
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pin_sina31s>;
status {
label = "sina31s:status:usr";
&gmac {
pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_mii_a>;
- phy = <&phy1>;
+ pinctrl-0 = <&gmac_mii_pins>;
+ phy-handle = <&phy1>;
phy-mode = "mii";
phy-supply = <®_dldo1>;
status = "okay";
-
- phy1: ethernet-phy@1 {
- reg = <1>;
- };
};
&hdmi {
&ir {
pinctrl-names = "default";
- pinctrl-0 = <&ir_pins_a>;
+ pinctrl-0 = <&s_ir_rx_pin>;
status = "okay";
};
vref-supply = <®_aldo3>;
status = "okay";
- button@158 {
+ button-158 {
label = "Volume Up";
linux,code = <KEY_VOLUMEUP>;
channel = <0>;
voltage = <158730>;
};
- button@349 {
+ button-349 {
label = "Volume Down";
linux,code = <KEY_VOLUMEDOWN>;
channel = <0>;
};
};
+&mdio {
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_sina31s>;
vmmc-supply = <®_dcdc1>;
bus-width = <4>;
cd-gpios = <&pio 0 4 GPIO_ACTIVE_LOW>; /* PA4 */
status = "okay";
};
-&pio {
- led_pin_sina31s: led_pin@0 {
- pins = "PH13";
- function = "gpio_out";
- };
-
- mmc0_cd_pin_sina31s: mmc0_cd_pin@0 {
- pins = "PA4";
- function = "gpio_in";
- bias-pull-up;
- };
-};
-
®_dldo1 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
&spdif {
pinctrl-names = "default";
- pinctrl-0 = <&spdif_pins_a>;
+ pinctrl-0 = <&spdif_tx_pin>;
status = "okay";
};
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins_bpi_m2>;
- blue {
+ led-0 {
label = "bpi-m2:blue:usr";
gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
};
- green {
+ led-1 {
label = "bpi-m2:green:usr";
gpios = <&pio 6 10 GPIO_ACTIVE_HIGH>; /* PG10 */
};
- red {
+ led-2 {
label = "bpi-m2:red:usr";
gpios = <&pio 6 5 GPIO_ACTIVE_HIGH>; /* PG5 */
};
mmc2_pwrseq: mmc2_pwrseq {
compatible = "mmc-pwrseq-simple";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc2_pwrseq_pin_bpi_m2>;
reset-gpios = <&r_pio 0 8 GPIO_ACTIVE_LOW>; /* PL8 WIFI_EN */
};
};
&gmac {
pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_rgmii_a>, <&gmac_phy_reset_pin_bpi_m2>;
- phy = <&phy1>;
+ pinctrl-0 = <&gmac_rgmii_pins>;
+ phy-handle = <&phy1>;
phy-mode = "rgmii";
phy-supply = <®_dldo1>;
- snps,reset-gpio = <&pio 0 21 GPIO_ACTIVE_HIGH>; /* PA21 */
- snps,reset-active-low;
- snps,reset-delays-us = <0 10000 30000>;
status = "okay";
-
- phy1: ethernet-phy@1 {
- reg = <1>;
- };
};
&ir {
pinctrl-names = "default";
- pinctrl-0 = <&ir_pins_a>;
+ pinctrl-0 = <&s_ir_rx_pin>;
status = "okay";
};
+&mdio {
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ reset-gpios = <&pio 0 21 GPIO_ACTIVE_LOW>; /* PA21 */
+ reset-assert-us = <10000>;
+ reset-deassert-us = <30000>;
+ };
+};
+
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bpi_m2>;
vmmc-supply = <®_dcdc1>;
bus-width = <4>;
cd-gpios = <&pio 0 4 GPIO_ACTIVE_LOW>; /* PA4 */
status = "okay";
};
-&mmc0_pins_a {
- bias-pull-up;
-};
-
&mmc2 {
pinctrl-names = "default";
- pinctrl-0 = <&mmc2_pins_a>;
+ pinctrl-0 = <&mmc2_4bit_pins>;
vmmc-supply = <®_aldo1>;
mmc-pwrseq = <&mmc2_pwrseq>;
bus-width = <4>;
};
};
-&mmc2_pins_a {
- bias-pull-up;
-};
-
&ohci0 {
status = "okay";
};
axp22x: pmic@68 {
compatible = "x-powers,axp221";
reg = <0x68>;
- interrupt-parent = <&nmi_intc>;
+ interrupt-parent = <&r_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
eldoin-supply = <®_dcdc1>;
x-powers,drive-vbus-en;
};
};
-&pio {
- gmac_phy_reset_pin_bpi_m2: gmac_phy_reset_pin@0 {
- pins = "PA21";
- function = "gpio_out";
- };
-
- led_pins_bpi_m2: led_pins@0 {
- pins = "PG5", "PG10", "PG11";
- function = "gpio_out";
- };
-
- mmc0_cd_pin_bpi_m2: mmc0_cd_pin@0 {
- pins = "PA4";
- function = "gpio_in";
- bias-pull-up;
- };
-};
-
-&r_pio {
- mmc2_pwrseq_pin_bpi_m2: mmc2_pwrseq_pin@0 {
- pins = "PL8";
- function = "gpio_out";
- };
-};
-
#include "axp22x.dtsi"
®_aldo1 {
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_ph_pins>;
status = "okay";
};
&usbphy {
status = "okay";
};
+
+&pio {
+ gpio-line-names =
+ /* PA */
+ "ETXD0", "ETXD1", "ETXD2", "ETXD3", "SDC0-DET", "", "",
+ "", "ETXCLK", "ETXEN", "EGTXCLK", "ERXD0", "ERXD1",
+ "ERXD2", "ERXD3", "", "", "", "", "ERXDV", "ERXCK",
+ "ETXERR", "ERXERR", "ECOL", "ECRS", "ECLKIN", "EMDC",
+ "EMDIO", "", "", "", "",
+
+ /* PB */
+ "CN7-P29", "CN7-P31", "CN7-P33", "CN7-P35", "CN7-P37",
+ "CN7-P28", "CN7-P27", "CN7-P32", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "",
+
+ /* PC */
+ "", "", "", "", "", "", "WL-SDIO-CMD", "WL-SDIO-CLK",
+ "WL-SDIO-D0", "WL-SDIO-D2", "WL-SDIO-D2", "WL-SDIO-D3",
+ "", "", "", "", "", "", "", "", "", "", "", "", "", "",
+ "", "USB-DRV", "", "", "", "",
+
+ /* PD */
+ "CN9-P09", "CN9-P11", "CN9-P13", "CN9-P15", "CN9-P17",
+ "CN9-P19", "CN9-P21", "CN9-P23", "CN9-P25", "CN9-P27",
+ "CN9-P29", "CN9-P31", "CN9-P33", "CN9-P35", "CN9-P37",
+ "CN9-P39", "CN9-P40", "CN9-P38", "CN9-P36", "CN9-P34",
+ "CN9-P32", "CN9-P30", "CN9-P28", "CN9-P26", "CN9-P22",
+ "CN9-P14", "CN9-P18", "CN9-P16", "", "", "", "",
+
+ /* PE */
+ "CN6-P20", "CN6-P24", "CN6-P30", "CN6-P28", "CN7-P08",
+ "CN7-P10", "CN7-P36", "CN7-P38", "CN6-P17", "CN6-P19",
+ "CN6-P21", "CN6-P23", "CN6-P25", "CN6-P27", "CN6-P29",
+ "CN6-P31", "", "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "",
+
+ /* PF */
+ "SDC0-D1", "SDC0-D0", "SDC0-CLK", "SDC0-CMD", "SDC0-D3",
+ "SDC0-D2", "", "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "", "", "", "", "",
+ "",
+
+ /* PG */
+ "CN9-P06", "CN9-P08", "CN9-P20", "CN9-P12", "CN9-P07",
+ "LED-PWR", "CN7-P13", "CN7-P11", "CN7-P22", "CN7-P15",
+ "LED-G", "LED-B", "CN7-P26", "CN7-P24", "CN7-P23",
+ "CN7-P19", "CN7-P21", "HCEC", "CN6-P22", "", "", "", "",
+ "", "", "", "", "", "", "", "", "",
+
+ /* PH */
+ "", "", "", "", "", "", "", "", "", "CN7-P07",
+ "CN7-P12", "CN7-P16", "CN7-P18", "CN9-P10", "CN6-P16",
+ "CN6-P14", "CN9-P04", "CN9-P02", "CN7-P05", "CN7-P03",
+ "CN8-P03", "CN8-P02", "", "", "CN6-P34", "CN6-P32",
+ "CN6-P26", "CN6-P18", "", "", "", "";
+};
+
+&r_pio {
+ gpio-line-names =
+ /* PL */
+ "PMU-SCK", "PMU-SDA", "VBAT-EN", "", "IR-RX",
+ "WL-WAKE-HOST", "BT-WAKE_HOST", "BT-ENABLE",
+ "WL-PMU-EN", "", "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "", "", "",
+
+ /* PM */
+ "CN6-P12", "CN6-P35", "CN7-P40", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "";
+};
};
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
};
&i2c2 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
};
status = "okay";
};
-&pio {
- mmc0_cd_pin_bs1078v2: mmc0_cd_pin@0 {
- pins = "PA8";
- function = "gpio_in";
- bias-pull-up;
- };
-};
-
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bs1078v2>;
vmmc-supply = <®_vcc3v0>;
bus-width = <4>;
cd-gpios = <&pio 0 8 GPIO_ACTIVE_LOW>; /* PA8 */
status = "okay";
};
-&mmc0_pins_a {
- bias-pull-up;
-};
-
&p2wi {
status = "okay";
axp22x: pmic@68 {
compatible = "x-powers,axp221";
reg = <0x68>;
- interrupt-parent = <&nmi_intc>;
+ interrupt-parent = <&r_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
};
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_ph_pins>;
status = "okay";
};
&mmc0 {
pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_e708_q1>;
+ pinctrl-0 = <&mmc0_pins>;
vmmc-supply = <®_dcdc1>;
bus-width = <4>;
cd-gpios = <&pio 0 8 GPIO_ACTIVE_LOW>; /* PA8 */
status = "okay";
};
-&pio {
- mmc0_cd_pin_e708_q1: mmc0_cd_pin@0 {
- pins = "PA8";
- function = "gpio_in";
- bias-pull-up;
- };
-
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
- pins = "PA15";
- function = "gpio_in";
- bias-pull-up;
- };
-};
-
&p2wi {
status = "okay";
axp22x: pmic@68 {
compatible = "x-powers,axp221";
reg = <0x68>;
- interrupt-parent = <&nmi_intc>;
+ interrupt-parent = <&r_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
drivevbus-supply = <®_vcc5v0>;
x-powers,drive-vbus-en;
};
&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_detect_pin>;
- usb0_id_det-gpio = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15 */
+ usb0_id_det-gpios = <&pio 0 15 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PA15 */
usb0_vbus_power-supply = <&usb_power_supply>;
usb0_vbus-supply = <®_drivevbus>;
usb1_vbus-supply = <®_dldo1>;
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#include "skeleton.dtsi"
-
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/sun8i-a23-a33-ccu.h>
/ {
interrupt-parent = <&gic>;
+ #address-cells = <1>;
+ #size-cells = <1>;
chosen {
#address-cells = <1>;
#size-cells = <1>;
ranges;
- simplefb_lcd: framebuffer@0 {
+ simplefb_lcd: framebuffer-lcd0 {
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0";
};
};
+ de: display-engine {
+ /* compatible gets set in SoC specific dtsi file */
+ allwinner,pipelines = <&fe0>;
+ status = "disabled";
+ };
+
timer {
compatible = "arm,armv7-timer";
interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
};
};
- soc@1c00000 {
+ soc {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
+ system-control@1c00000 {
+ compatible = "allwinner,sun8i-a23-system-control";
+ reg = <0x01c00000 0x30>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ sram_c: sram@1d00000 {
+ compatible = "mmio-sram";
+ reg = <0x01d00000 0x80000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x01d00000 0x80000>;
+
+ ve_sram: sram-section@0 {
+ compatible = "allwinner,sun8i-a23-sram-c1",
+ "allwinner,sun4i-a10-sram-c1";
+ reg = <0x000000 0x80000>;
+ };
+ };
+ };
+
dma: dma-controller@1c02000 {
compatible = "allwinner,sun8i-a23-dma";
reg = <0x01c02000 0x1000>;
#dma-cells = <1>;
};
+ nfc: nand-controller@1c03000 {
+ compatible = "allwinner,sun8i-a23-nand-controller";
+ reg = <0x01c03000 0x1000>;
+ interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_NAND>, <&ccu CLK_NAND>;
+ clock-names = "ahb", "mod";
+ resets = <&ccu RST_BUS_NAND>;
+ reset-names = "ahb";
+ dmas = <&dma 5>;
+ dma-names = "rxtx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&nand_pins &nand_cs0_pin &nand_rb0_pin>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ tcon0: lcd-controller@1c0c000 {
+ /* compatible gets set in SoC specific dtsi file */
+ reg = <0x01c0c000 0x1000>;
+ interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&dma 12>;
+ clocks = <&ccu CLK_BUS_LCD>,
+ <&ccu CLK_LCD_CH0>,
+ <&ccu 13>;
+ clock-names = "ahb",
+ "tcon-ch0",
+ "lvds-alt";
+ clock-output-names = "tcon-pixel-clock";
+ #clock-cells = <0>;
+ resets = <&ccu RST_BUS_LCD>,
+ <&ccu RST_BUS_LVDS>;
+ reset-names = "lcd",
+ "lvds";
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon0_in: port@0 {
+ reg = <0>;
+
+ tcon0_in_drc0: endpoint {
+ remote-endpoint = <&drc0_out_tcon0>;
+ };
+ };
+
+ tcon0_out: port@1 {
+ reg = <1>;
+ };
+ };
+ };
+
mmc0: mmc@1c0f000 {
compatible = "allwinner,sun7i-a20-mmc";
reg = <0x01c0f000 0x1000>;
resets = <&ccu RST_BUS_MMC0>;
reset-names = "ahb";
interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
#size-cells = <0>;
};
- nfc: nand@1c03000 {
- compatible = "allwinner,sun4i-a10-nand";
- reg = <0x01c03000 0x1000>;
- interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_NAND>, <&ccu CLK_NAND>;
- clock-names = "ahb", "mod";
- resets = <&ccu RST_BUS_NAND>;
- reset-names = "ahb";
- pinctrl-names = "default";
- pinctrl-0 = <&nand_pins &nand_pins_cs0 &nand_pins_rb0>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
usb_otg: usb@1c19000 {
/* compatible gets set in SoC specific dtsi file */
reg = <0x01c19000 0x0400>;
phys = <&usbphy 0>;
phy-names = "usb";
extcon = <&usbphy 0>;
+ dr_mode = "otg";
status = "disabled";
};
#interrupt-cells = <3>;
#gpio-cells = <3>;
- uart0_pins_a: uart0@0 {
- pins = "PF2", "PF4";
- function = "uart0";
+ i2c0_pins: i2c0-pins {
+ pins = "PH2", "PH3";
+ function = "i2c0";
};
- uart1_pins_a: uart1@0 {
- pins = "PG6", "PG7";
- function = "uart1";
+ i2c1_pins: i2c1-pins {
+ pins = "PH4", "PH5";
+ function = "i2c1";
};
- uart1_pins_cts_rts_a: uart1-cts-rts@0 {
- pins = "PG8", "PG9";
- function = "uart1";
+ i2c2_pins: i2c2-pins {
+ pins = "PE12", "PE13";
+ function = "i2c2";
};
- mmc0_pins_a: mmc0@0 {
+ lcd_rgb666_pins: lcd-rgb666-pins {
+ pins = "PD2", "PD3", "PD4", "PD5", "PD6", "PD7",
+ "PD10", "PD11", "PD12", "PD13", "PD14", "PD15",
+ "PD18", "PD19", "PD20", "PD21", "PD22", "PD23",
+ "PD24", "PD25", "PD26", "PD27";
+ function = "lcd0";
+ };
+
+ mmc0_pins: mmc0-pins {
pins = "PF0", "PF1", "PF2",
"PF3", "PF4", "PF5";
function = "mmc0";
bias-pull-up;
};
- mmc1_pins_a: mmc1@0 {
+ mmc1_pg_pins: mmc1-pg-pins {
pins = "PG0", "PG1", "PG2",
"PG3", "PG4", "PG5";
function = "mmc1";
bias-pull-up;
};
- mmc2_8bit_pins: mmc2_8bit {
+ mmc2_8bit_pins: mmc2-8bit-pins {
pins = "PC5", "PC6", "PC8",
"PC9", "PC10", "PC11",
"PC12", "PC13", "PC14",
function = "nand0";
};
- nand_pins_cs0: nand-pins-cs0 {
+ nand_cs0_pin: nand-cs0-pin {
pins = "PC4";
function = "nand0";
bias-pull-up;
};
- nand_pins_cs1: nand-pins-cs1 {
+ nand_cs1_pin: nand-cs1-pin {
pins = "PC3";
function = "nand0";
bias-pull-up;
};
- nand_pins_rb0: nand-pins-rb0 {
+ nand_rb0_pin: nand-rb0-pin {
pins = "PC6";
function = "nand0";
bias-pull-up;
};
- nand_pins_rb1: nand-pins-rb1 {
+ nand_rb1_pin: nand-rb1-pin {
pins = "PC7";
function = "nand0";
bias-pull-up;
};
- pwm0_pins: pwm0 {
+ pwm0_pin: pwm0-pin {
pins = "PH0";
function = "pwm0";
};
- i2c0_pins_a: i2c0@0 {
- pins = "PH2", "PH3";
- function = "i2c0";
- };
-
- i2c1_pins_a: i2c1@0 {
- pins = "PH4", "PH5";
- function = "i2c1";
+ uart0_pf_pins: uart0-pf-pins {
+ pins = "PF2", "PF4";
+ function = "uart0";
};
- i2c2_pins_a: i2c2@0 {
- pins = "PE12", "PE13";
- function = "i2c2";
+ uart1_pg_pins: uart1-pg-pins {
+ pins = "PG6", "PG7";
+ function = "uart1";
};
- lcd_rgb666_pins: lcd-rgb666@0 {
- pins = "PD2", "PD3", "PD4", "PD5", "PD6", "PD7",
- "PD10", "PD11", "PD12", "PD13", "PD14", "PD15",
- "PD18", "PD19", "PD20", "PD21", "PD22", "PD23",
- "PD24", "PD25", "PD26", "PD27";
- function = "lcd0";
+ uart1_cts_rts_pg_pins: uart1-cts-rts-pg-pins {
+ pins = "PG8", "PG9";
+ function = "uart1";
};
};
timer@1c20c00 {
- compatible = "allwinner,sun4i-a10-timer";
+ compatible = "allwinner,sun8i-a23-timer";
reg = <0x01c20c00 0xa0>;
interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
compatible = "allwinner,sun6i-a31-wdt";
reg = <0x01c20ca0 0x20>;
interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&osc24M>;
};
pwm: pwm@1c21400 {
interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_I2C0>;
resets = <&ccu RST_BUS_I2C0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_I2C1>;
resets = <&ccu RST_BUS_I2C1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_I2C2>;
resets = <&ccu RST_BUS_I2C2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
gic: interrupt-controller@1c81000 {
- compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
+ compatible = "arm,gic-400";
reg = <0x01c81000 0x1000>,
<0x01c82000 0x2000>,
<0x01c84000 0x2000>,
interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
};
+ fe0: display-frontend@1e00000 {
+ /* compatible gets set in SoC specific dtsi file */
+ reg = <0x01e00000 0x20000>;
+ interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_DE_FE>, <&ccu CLK_DE_FE>,
+ <&ccu CLK_DRAM_DE_FE>;
+ clock-names = "ahb", "mod",
+ "ram";
+ resets = <&ccu RST_BUS_DE_FE>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fe0_out: port@1 {
+ reg = <1>;
+
+ fe0_out_be0: endpoint {
+ remote-endpoint = <&be0_in_fe0>;
+ };
+ };
+ };
+ };
+
+ be0: display-backend@1e60000 {
+ /* compatible gets set in SoC specific dtsi file */
+ reg = <0x01e60000 0x10000>;
+ interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_DE_BE>, <&ccu CLK_DE_BE>,
+ <&ccu CLK_DRAM_DE_BE>;
+ clock-names = "ahb", "mod",
+ "ram";
+ resets = <&ccu RST_BUS_DE_BE>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ be0_in: port@0 {
+ reg = <0>;
+
+ be0_in_fe0: endpoint {
+ remote-endpoint = <&fe0_out_be0>;
+ };
+ };
+
+ be0_out: port@1 {
+ reg = <1>;
+
+ be0_out_drc0: endpoint {
+ remote-endpoint = <&drc0_in_be0>;
+ };
+ };
+ };
+ };
+
+ drc0: drc@1e70000 {
+ /* compatible gets set in SoC specific dtsi file */
+ reg = <0x01e70000 0x10000>;
+ interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_DRC>, <&ccu CLK_DRC>,
+ <&ccu CLK_DRAM_DRC>;
+ clock-names = "ahb", "mod", "ram";
+ resets = <&ccu RST_BUS_DRC>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ drc0_in: port@0 {
+ reg = <0>;
+
+ drc0_in_be0: endpoint {
+ remote-endpoint = <&be0_out_drc0>;
+ };
+ };
+
+ drc0_out: port@1 {
+ reg = <1>;
+
+ drc0_out_tcon0: endpoint {
+ remote-endpoint = <&tcon0_in_drc0>;
+ };
+ };
+ };
+ };
+
rtc: rtc@1f00000 {
- compatible = "allwinner,sun6i-a31-rtc";
- reg = <0x01f00000 0x54>;
+ compatible = "allwinner,sun8i-a23-rtc";
+ reg = <0x01f00000 0x400>;
interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
- clock-output-names = "osc32k";
+ clock-output-names = "osc32k", "osc32k-out";
clocks = <&ext_osc32k>;
#clock-cells = <1>;
};
- nmi_intc: interrupt-controller@1f00c00 {
+ r_intc: interrupt-controller@1f00c00 {
compatible = "allwinner,sun6i-a31-r-intc";
interrupt-controller;
#interrupt-cells = <2>;
status = "disabled";
};
+ r_i2c: i2c@1f02400 {
+ compatible = "allwinner,sun8i-a23-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x01f02400 0x400>;
+ interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&r_i2c_pins>;
+ clocks = <&apb0_gates 6>;
+ resets = <&apb0_rst 6>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
r_pio: pinctrl@1f02c00 {
compatible = "allwinner,sun8i-a23-r-pinctrl";
reg = <0x01f02c00 0x400>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <3>;
- #address-cells = <1>;
- #size-cells = <0>;
#gpio-cells = <3>;
- r_rsb_pins: r_rsb {
+ r_i2c_pins: r-i2c-pins {
+ pins = "PL0", "PL1";
+ function = "s_i2c";
+ bias-pull-up;
+ };
+
+ r_rsb_pins: r-rsb-pins {
pins = "PL0", "PL1";
function = "s_rsb";
drive-strength = <20>;
bias-pull-up;
};
- r_uart_pins_a: r_uart@0 {
+ r_uart_pins_a: r-uart-pins {
pins = "PL2", "PL3";
function = "s_uart";
};
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
};
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
};
vref-supply = <®_vcc3v0>;
status = "okay";
- button@190 {
+ button-190 {
label = "Volume Up";
linux,code = <KEY_VOLUMEUP>;
channel = <0>;
voltage = <190000>;
};
- button@390 {
+ button-390 {
label = "Volume Down";
linux,code = <KEY_VOLUMEDOWN>;
channel = <0>;
voltage = <390000>;
};
- button@600 {
+ button-600 {
label = "Home";
linux,code = <KEY_HOME>;
channel = <0>;
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_evb>;
vmmc-supply = <®_vcc3v0>;
bus-width = <4>;
cd-gpios = <&pio 1 4 GPIO_ACTIVE_LOW>; /* PB4 */
status = "okay";
};
-&pio {
- mmc0_cd_pin_evb: mmc0_cd_pin@0 {
- pins = "PB4";
- function = "gpio_in";
- bias-pull-up;
- };
-};
-
/*
* The RX line has a non-populated resistance. In order to use it, you
* need to solder R207 on the back of the board in order to close the
};
&lradc {
- button@600 {
+ button-600 {
label = "Back";
linux,code = <KEY_BACK>;
channel = <0>;
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-a23.dtsi"
+#include "sun8i-q8-common.dtsi"
+
+/ {
+ model = "Q8 A23 Tablet";
+ compatible = "allwinner,q8-a23", "allwinner,sun8i-a23";
+};
+
+&codec {
+ allwinner,pa-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */
+ allwinner,audio-routing =
+ "Headphone", "HP",
+ "Headphone", "HPCOM",
+ "Speaker", "HP",
+ "MIC1", "Mic",
+ "MIC2", "Headset Mic",
+ "Mic", "MBIAS",
+ "Headset Mic", "HBIAS";
+ status = "okay";
+};
+
+&panel {
+ compatible = "bananapi,s070wv20-ct16";
+};
+
+&tcon0_out {
+ tcon0_out_lcd: endpoint {
+ remote-endpoint = <&panel_input>;
+ };
+};
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-a23.dtsi"
+#include "sun8i-q8-common.dtsi"
+
+/ {
+ model = "Q8 A23 Tablet";
+ compatible = "allwinner,q8-a23", "allwinner,sun8i-a23";
+};
+
+&codec {
+ allwinner,pa-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */
+ allwinner,audio-routing =
+ "Headphone", "HP",
+ "Headphone", "HPCOM",
+ "Speaker", "HP",
+ "MIC1", "Mic",
+ "MIC2", "Headset Mic",
+ "Mic", "MBIAS",
+ "Headset Mic", "HBIAS";
+ status = "okay";
+};
+
+&panel {
+ compatible = "bananapi,s070wv20-ct16";
+};
+
+&tcon0_out {
+ tcon0_out_lcd: endpoint {
+ remote-endpoint = <&panel_input>;
+ };
+};
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
- pinctrl-names = "default";
- pinctrl-0 = <&wifi_pwrseq_pin_mid2407>;
reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL6 */
/* The esp8089 needs 200 ms after driving wifi-en high */
post-power-on-delay-ms = <200>;
&mmc1 {
pinctrl-names = "default";
- pinctrl-0 = <&mmc1_pins_a>;
+ pinctrl-0 = <&mmc1_pg_pins>;
vmmc-supply = <®_dldo1>;
mmc-pwrseq = <&wifi_pwrseq>;
bus-width = <4>;
};
};
-&mmc1_pins_a {
- bias-pull-up;
-};
-
-&r_pio {
- wifi_pwrseq_pin_mid2407: wifi_pwrseq_pin@0 {
- pins = "PL6";
- function = "gpio_out";
- };
-};
-
&touchscreen {
reg = <0x40>;
compatible = "silead,gsl1680";
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
- pinctrl-names = "default";
- pinctrl-0 = <&wifi_pwrseq_pin_mid2809>;
reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL6 */
/* The esp8089 needs 200 ms after driving wifi-en high */
post-power-on-delay-ms = <200>;
&mmc1 {
pinctrl-names = "default";
- pinctrl-0 = <&mmc1_pins_a>;
+ pinctrl-0 = <&mmc1_pg_pins>;
vmmc-supply = <®_dldo1>;
mmc-pwrseq = <&wifi_pwrseq>;
bus-width = <4>;
};
};
-&mmc1_pins_a {
- bias-pull-up;
-};
-
-&r_pio {
- wifi_pwrseq_pin_mid2809: wifi_pwrseq_pin@0 {
- pins = "PL6";
- function = "gpio_out";
- };
-};
-
&touchscreen {
reg = <0x40>;
compatible = "silead,gsl3670";
"Headset Mic", "HBIAS";
status = "okay";
};
+
+&panel {
+ compatible = "bananapi,s070wv20-ct16";
+};
+
+&tcon0_out {
+ tcon0_out_lcd: endpoint {
+ remote-endpoint = <&panel_input>;
+ };
+};
#include "sun8i-a23-a33.dtsi"
/ {
- memory {
- reg = <0x40000000 0x40000000>;
- };
-
- soc@1c00000 {
+ soc {
codec: codec@1c22c00 {
#sound-dai-cells = <0>;
compatible = "allwinner,sun8i-a23-codec";
};
};
+&be0 {
+ compatible = "allwinner,sun8i-a23-display-backend";
+};
+
&ccu {
compatible = "allwinner,sun8i-a23-ccu";
};
+&de {
+ compatible = "allwinner,sun8i-a23-display-engine";
+};
+
+&drc0 {
+ compatible = "allwinner,sun8i-a23-drc";
+};
+
+&fe0 {
+ compatible = "allwinner,sun8i-a23-display-frontend";
+};
+
&pio {
compatible = "allwinner,sun8i-a23-pinctrl";
interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
};
+&tcon0 {
+ compatible = "allwinner,sun8i-a23-tcon";
+};
+
&usb_otg {
compatible = "allwinner,sun6i-a31-musb";
};
/*
- * Copyright (c) 2016 FUKAUMI Naoki <naobsd@gmail.com>
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
/dts-v1/;
#include "sun8i-a33.dtsi"
+#include "sun8i-q8-common.dtsi"
/ {
- model = "Nintendo NES Classic Edition";
- compatible = "nintendo,nes-classic-edition", "allwinner,sun8i-a33";
-
- aliases {
- serial0 = &uart0;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
+ model = "Q8 A33 Tablet";
+ compatible = "allwinner,q8-a33", "allwinner,sun8i-a33";
};
-&uart0 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
- status = "okay";
-};
-
-&nfc {
- status = "okay";
-
- nand@0 {
- #address-cells = <1>;
- #size-cells = <1>;
+&tcon0_out {
+ tcon0_out_lcd: endpoint@0 {
reg = <0>;
- allwinner,rb = <0>;
- nand-ecc-mode = "hw";
+ remote-endpoint = <&panel_input>;
};
};
};
&lradc {
- button@600 {
+ button-600 {
label = "Back";
linux,code = <KEY_BACK>;
channel = <0>;
&mmc1 {
pinctrl-names = "default";
- pinctrl-0 = <&mmc1_pins_a>;
+ pinctrl-0 = <&mmc1_pg_pins>;
vmmc-supply = <®_dldo1>;
bus-width = <4>;
non-removable;
pinctrl-names = "default";
pinctrl-0 = <&led_pin_d978>;
- home {
+ led {
label = "d978:blue:home";
gpios = <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /* PL5 */
};
};
};
-&mmc1_pins_a {
- bias-pull-up;
-};
-
&mmc1 {
pinctrl-names = "default";
- pinctrl-0 = <&mmc1_pins_a>;
+ pinctrl-0 = <&mmc1_pg_pins>;
vmmc-supply = <®_dldo1>;
bus-width = <4>;
non-removable;
};
&r_pio {
- led_pin_d978: led_pin_d978@0 {
+ led_pin_d978: led-pin {
pins = "PL5";
function = "gpio_out";
drive-strength = <20>;
&uart1 {
pinctrl-names = "default";
- pinctrl-0 = <&uart1_pins_a>,
- <&uart1_pins_cts_rts_a>;
+ pinctrl-0 = <&uart1_pg_pins>,
+ <&uart1_cts_rts_pg_pins>;
status = "okay";
};
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-a33.dtsi"
+#include "sun8i-q8-common.dtsi"
+
+/ {
+ model = "Q8 A33 Tablet";
+ compatible = "allwinner,q8-a33", "allwinner,sun8i-a33";
+};
+
+&tcon0_out {
+ tcon0_out_lcd: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&panel_input>;
+ };
+};
leds {
compatible = "gpio-leds";
- green {
+ led {
label = "a33-olinuxino:green:usr";
gpios = <&pio 1 7 GPIO_ACTIVE_HIGH>;
};
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>;
vmmc-supply = <®_dcdc1>;
bus-width = <4>;
cd-gpios = <&pio 1 4 GPIO_ACTIVE_LOW>; /* PB4 */
axp22x: pmic@3a3 {
compatible = "x-powers,axp223";
reg = <0x3a3>;
- interrupt-parent = <&nmi_intc>;
+ interrupt-parent = <&r_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
eldoin-supply = <®_dcdc1>;
x-powers,drive-vbus-en;
"Headphone", "Headphone Jack";
/* Board level routing. First 2 routes copied from SoC level */
simple-audio-card,routing =
- "Left DAC", "AIF1 Slot 0 Left",
- "Right DAC", "AIF1 Slot 0 Right",
+ "Left DAC", "DACL",
+ "Right DAC", "DACR",
"HP", "HPCOM",
"Headphone Jack", "HP",
"MIC1", "Microphone Jack",
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_b>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
model = "Q8 A33 Tablet";
compatible = "allwinner,q8-a33", "allwinner,sun8i-a33";
};
+
+&tcon0_out {
+ tcon0_out_lcd: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&panel_input>;
+ };
+};
panel {
compatible = "netron-dy,e231732";
- #address-cells = <1>;
- #size-cells = <0>;
+ power-supply = <®_vcc3v3>;
- port@0 {
- reg = <0>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- panel_input: endpoint@0 {
- reg = <0>;
+ port {
+ panel_input: endpoint {
remote-endpoint = <&tcon0_out_panel>;
};
};
vref-supply = <®_dcdc1>;
status = "okay";
- button@200 {
+ button-200 {
label = "Volume Up";
linux,code = <KEY_VOLUMEUP>;
channel = <0>;
voltage = <191011>;
};
- button@400 {
+ button-400 {
label = "Volume Down";
linux,code = <KEY_VOLUMEDOWN>;
channel = <0>;
voltage = <391304>;
};
- button@600 {
+ button-600 {
label = "Home";
linux,code = <KEY_HOME>;
channel = <0>;
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_sina33>;
vmmc-supply = <®_dcdc1>;
bus-width = <4>;
cd-gpios = <&pio 1 4 GPIO_ACTIVE_LOW>; /* PB4 */
&mmc2_8bit_pins {
/* Increase drive strength for DDR modes */
drive-strength = <40>;
- /* eMMC is missing pull-ups */
- bias-pull-up;
};
&ohci0 {
status = "okay";
};
-&pio {
- mmc0_cd_pin_sina33: mmc0_cd_pin@0 {
- pins = "PB4";
- function = "gpio_in";
- bias-pull-up;
- };
-};
-
&r_rsb {
status = "okay";
axp22x: pmic@3a3 {
compatible = "x-powers,axp223";
reg = <0x3a3>;
- interrupt-parent = <&nmi_intc>;
+ interrupt-parent = <&r_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
eldoin-supply = <®_dcdc1>;
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_b>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
#include <dt-bindings/thermal/thermal.h>
/ {
- cpu0_opp_table: opp_table0 {
+ cpu0_opp_table: opp-table-cpu {
compatible = "operating-points-v2";
opp-shared;
#cooling-cells = <2>;
};
- cpu@1 {
+ cpu1: cpu@1 {
+ clocks = <&ccu CLK_CPUX>;
+ clock-names = "cpu";
operating-points-v2 = <&cpu0_opp_table>;
+ #cooling-cells = <2>;
};
- cpu@2 {
+ cpu2: cpu@2 {
compatible = "arm,cortex-a7";
device_type = "cpu";
reg = <2>;
+ clocks = <&ccu CLK_CPUX>;
+ clock-names = "cpu";
operating-points-v2 = <&cpu0_opp_table>;
+ #cooling-cells = <2>;
};
- cpu@3 {
+ cpu3: cpu@3 {
compatible = "arm,cortex-a7";
device_type = "cpu";
reg = <3>;
+ clocks = <&ccu CLK_CPUX>;
+ clock-names = "cpu";
operating-points-v2 = <&cpu0_opp_table>;
+ #cooling-cells = <2>;
};
};
- de: display-engine {
- compatible = "allwinner,sun8i-a33-display-engine";
- allwinner,pipelines = <&fe0>;
- status = "disabled";
- };
-
iio-hwmon {
compatible = "iio-hwmon";
io-channels = <&ths>;
};
- mali_opp_table: gpu-opp-table {
+ mali_opp_table: opp-table-gpu {
compatible = "operating-points-v2";
opp-144000000 {
};
};
- memory {
- reg = <0x40000000 0x80000000>;
- };
-
sound: sound {
compatible = "simple-audio-card";
simple-audio-card,name = "sun8i-a33-audio";
simple-audio-card,format = "i2s";
simple-audio-card,frame-master = <&link_codec>;
simple-audio-card,bitclock-master = <&link_codec>;
- simple-audio-card,mclk-fs = <512>;
+ simple-audio-card,mclk-fs = <128>;
simple-audio-card,aux-devs = <&codec_analog>;
simple-audio-card,routing =
- "Left DAC", "AIF1 Slot 0 Left",
- "Right DAC", "AIF1 Slot 0 Right";
+ "Left DAC", "DACL",
+ "Right DAC", "DACR";
status = "disabled";
simple-audio-card,cpu {
};
link_codec: simple-audio-card,codec {
- sound-dai = <&codec>;
+ sound-dai = <&codec 0>;
};
};
- soc@1c00000 {
- tcon0: lcd-controller@1c0c000 {
- compatible = "allwinner,sun8i-a33-tcon";
- reg = <0x01c0c000 0x1000>;
- interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_LCD>,
- <&ccu CLK_LCD_CH0>;
- clock-names = "ahb",
- "tcon-ch0";
- clock-output-names = "tcon-pixel-clock";
- resets = <&ccu RST_BUS_LCD>;
- reset-names = "lcd";
- status = "disabled";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- tcon0_in: port@0 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>;
-
- tcon0_in_drc0: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&drc0_out_tcon0>;
- };
- };
-
- tcon0_out: port@1 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <1>;
-
- tcon0_out_dsi: endpoint@1 {
- reg = <1>;
- remote-endpoint = <&dsi_in_tcon0>;
- };
- };
- };
+ soc {
+ video-codec@1c0e000 {
+ compatible = "allwinner,sun8i-a33-video-engine";
+ reg = <0x01c0e000 0x1000>;
+ clocks = <&ccu CLK_BUS_VE>, <&ccu CLK_VE>,
+ <&ccu CLK_DRAM_VE>;
+ clock-names = "ahb", "mod", "ram";
+ resets = <&ccu RST_BUS_VE>;
+ interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
+ allwinner,sram = <&ve_sram 1>;
};
crypto: crypto-engine@1c15000 {
- compatible = "allwinner,sun4i-a10-crypto";
+ compatible = "allwinner,sun8i-a33-crypto";
reg = <0x01c15000 0x1000>;
interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_SS>, <&ccu CLK_SS>;
};
codec: codec@1c22e00 {
- #sound-dai-cells = <0>;
+ #sound-dai-cells = <1>;
compatible = "allwinner,sun8i-a33-codec";
reg = <0x01c22e00 0x400>;
interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
phys = <&dphy>;
phy-names = "dphy";
status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>;
-
- dsi_in_tcon0: endpoint {
- remote-endpoint = <&tcon0_out_dsi>;
- };
+ port {
+ dsi_in_tcon0: endpoint {
+ remote-endpoint = <&tcon0_out_dsi>;
};
};
};
status = "disabled";
#phy-cells = <0>;
};
-
- fe0: display-frontend@1e00000 {
- compatible = "allwinner,sun8i-a33-display-frontend";
- reg = <0x01e00000 0x20000>;
- interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_DE_FE>, <&ccu CLK_DE_FE>,
- <&ccu CLK_DRAM_DE_FE>;
- clock-names = "ahb", "mod",
- "ram";
- resets = <&ccu RST_BUS_DE_FE>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- fe0_out: port@1 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <1>;
-
- fe0_out_be0: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&be0_in_fe0>;
- };
- };
- };
- };
-
- be0: display-backend@1e60000 {
- compatible = "allwinner,sun8i-a33-display-backend";
- reg = <0x01e60000 0x10000>, <0x01e80000 0x1000>;
- reg-names = "be", "sat";
- interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_DE_BE>, <&ccu CLK_DE_BE>,
- <&ccu CLK_DRAM_DE_BE>, <&ccu CLK_BUS_SAT>;
- clock-names = "ahb", "mod",
- "ram", "sat";
- resets = <&ccu RST_BUS_DE_BE>, <&ccu RST_BUS_SAT>;
- reset-names = "be", "sat";
- assigned-clocks = <&ccu CLK_DE_BE>;
- assigned-clock-rates = <300000000>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- be0_in: port@0 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>;
-
- be0_in_fe0: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&fe0_out_be0>;
- };
- };
-
- be0_out: port@1 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <1>;
-
- be0_out_drc0: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&drc0_in_be0>;
- };
- };
- };
- };
-
- drc0: drc@1e70000 {
- compatible = "allwinner,sun8i-a33-drc";
- reg = <0x01e70000 0x10000>;
- interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_DRC>, <&ccu CLK_DRC>,
- <&ccu CLK_DRAM_DRC>;
- clock-names = "ahb", "mod", "ram";
- resets = <&ccu RST_BUS_DRC>;
-
- assigned-clocks = <&ccu CLK_DRC>;
- assigned-clock-rates = <300000000>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- drc0_in: port@0 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>;
-
- drc0_in_be0: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&be0_out_drc0>;
- };
- };
-
- drc0_out: port@1 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <1>;
-
- drc0_out_tcon0: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&tcon0_in_drc0>;
- };
- };
- };
- };
};
thermal-zones {
- cpu_thermal {
+ cpu-thermal {
/* milliseconds */
polling-delay-passive = <250>;
polling-delay = <1000>;
cooling-maps {
map0 {
trip = <&cpu_alert0>;
- cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
map1 {
trip = <&cpu_alert1>;
- cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
map2 {
};
};
+&be0 {
+ compatible = "allwinner,sun8i-a33-display-backend";
+ /* A33 has an extra "SAT" module packed inside the display backend */
+ reg = <0x01e60000 0x10000>, <0x01e80000 0x1000>;
+ reg-names = "be", "sat";
+ clocks = <&ccu CLK_BUS_DE_BE>, <&ccu CLK_DE_BE>,
+ <&ccu CLK_DRAM_DE_BE>, <&ccu CLK_BUS_SAT>;
+ clock-names = "ahb", "mod",
+ "ram", "sat";
+ resets = <&ccu RST_BUS_DE_BE>, <&ccu RST_BUS_SAT>;
+ reset-names = "be", "sat";
+};
+
&ccu {
compatible = "allwinner,sun8i-a33-ccu";
};
+&de {
+ compatible = "allwinner,sun8i-a33-display-engine";
+};
+
+&drc0 {
+ compatible = "allwinner,sun8i-a33-drc";
+};
+
+&fe0 {
+ compatible = "allwinner,sun8i-a33-display-frontend";
+};
+
&mali {
operating-points-v2 = <&mali_opp_table>;
};
interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
- uart0_pins_b: uart0@1 {
+ uart0_pb_pins: uart0-pb-pins {
pins = "PB0", "PB1";
function = "uart0";
};
};
+&tcon0 {
+ compatible = "allwinner,sun8i-a33-tcon";
+};
+
+&tcon0_out {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon0_out_dsi: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&dsi_in_tcon0>;
+ };
+};
+
&usb_otg {
compatible = "allwinner,sun8i-a33-musb";
};
ethernet0 = &sdio_wifi;
};
+ panel: panel {
+ /* Tablet dts should provide panel compatible */
+ backlight = <&backlight>;
+ enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
+ power-supply = <®_dc1sw>;
+
+ port {
+ panel_input: endpoint {
+ remote-endpoint = <&tcon0_out_lcd>;
+ };
+ };
+ };
+
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
/*
};
};
+&de {
+ status = "okay";
+};
+
&ehci0 {
status = "okay";
};
&mmc1 {
pinctrl-names = "default";
- pinctrl-0 = <&mmc1_pins_a>;
+ pinctrl-0 = <&mmc1_pg_pins>;
vmmc-supply = <®_dldo1>;
mmc-pwrseq = <&wifi_pwrseq>;
bus-width = <4>;
};
};
-&mmc1_pins_a {
- bias-pull-up;
-};
-
&r_pio {
- wifi_pwrseq_pin_q8: wifi_pwrseq_pin@0 {
+ wifi_pwrseq_pin_q8: wifi-pwrseq-pins {
pins = "PL6", "PL7", "PL11";
function = "gpio_in";
bias-pull-up;
};
};
+&tcon0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcd_rgb666_pins>;
+ status = "okay";
+};
+
&usbphy {
usb1_vbus-supply = <®_dldo1>;
};
leds {
compatible = "gpio-leds";
- blue {
+ led-0 {
label = "bpi-m2m:blue:usr";
gpios = <&pio 2 7 GPIO_ACTIVE_LOW>;
};
- green {
+ led-1 {
label = "bpi-m2m:green:usr";
gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>;
};
- red {
+ led-2 {
label = "bpi-m2m:red:power";
gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
default-state = "on";
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL06 */
+ clocks = <&rtc 1>;
+ clock-names = "ext_clock";
};
};
};
&cpu0_opp_table {
- opp@1104000000 {
+ opp-1104000000 {
opp-hz = /bits/ 64 <1104000000>;
opp-microvolt = <1320000>;
clock-latency-ns = <244144>; /* 8 32k periods */
};
- opp@1200000000 {
+ opp-1200000000 {
opp-hz = /bits/ 64 <1200000000>;
opp-microvolt = <1320000>;
clock-latency-ns = <244144>; /* 8 32k periods */
status = "okay";
};
-/* This is the i2c bus exposed on the DSI connector for the touch panel */
-&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
- status = "disabled";
-};
-
-/* This is the i2c bus exposed on the GPIO header */
-&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
- status = "disabled";
-};
-
-/* This is the i2c bus exposed on the CSI connector to control the sensor */
-&i2c2 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_a>;
- status = "disabled";
-};
-
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>;
vmmc-supply = <®_dcdc1>;
bus-width = <4>;
cd-gpios = <&pio 1 4 GPIO_ACTIVE_LOW>; /* PB4 */
&mmc1 {
pinctrl-names = "default";
- pinctrl-0 = <&mmc1_pins_a>;
+ pinctrl-0 = <&mmc1_pg_pins>;
vmmc-supply = <®_aldo1>;
mmc-pwrseq = <&wifi_pwrseq>;
bus-width = <4>;
axp22x: pmic@3a3 {
compatible = "x-powers,axp223";
reg = <0x3a3>;
- interrupt-parent = <&nmi_intc>;
+ interrupt-parent = <&r_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
eldoin-supply = <®_dcdc1>;
x-powers,drive-vbus-en;
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_b>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
&uart1 {
pinctrl-names = "default";
- pinctrl-0 = <&uart1_pins_a>, <&uart1_pins_cts_rts_a>;
+ pinctrl-0 = <&uart1_pg_pins>, <&uart1_cts_rts_pg_pins>;
+ uart-has-rtscts;
status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ clocks = <&rtc 1>;
+ clock-names = "lpo";
+ vbat-supply = <®_dldo1>;
+ vddio-supply = <®_aldo3>;
+ device-wakeup-gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
+ host-wakeup-gpios = <&r_pio 0 9 GPIO_ACTIVE_HIGH>; /* PL9 */
+ shutdown-gpios = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
+ };
};
&usb_otg {
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0 OR X11
+/* Copyright (c) 2016 FUKAUMI Naoki <naobsd@gmail.com> */
+
+/dts-v1/;
+#include "sun8i-a33.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+/ {
+ model = "Nintendo NES Classic Edition";
+ compatible = "nintendo,nes-classic", "allwinner,sun8i-r16",
+ "allwinner,sun8i-a33";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&uart0 {
+ /*
+ * UART0 is available on two ports: PB and PF, both are accessible.
+ * PF can also be used for the SD card so PB is preferred.
+ */
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pf_pins>;
+ status = "okay";
+};
+
+&nfc {
+ status = "okay";
+
+ /* 2Gb Macronix MX30LF2G18AC (3V) */
+ nand@0 {
+ reg = <0>;
+ allwinner,rb = <0>;
+ nand-ecc-mode = "hw";
+ nand-ecc-strength = <16>;
+ nand-ecc-step-size = <1024>;
+ };
+};
+
+&usb_otg {
+ status = "okay";
+ dr_mode = "otg";
+};
+
+&usbphy {
+ /* VBUS is always on because it is wired to the power supply */
+ usb1_vbus-supply = <®_vcc5v0>;
+ status = "okay";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0 OR X11
+/* Copyright (c) 2018 Miquèl RAYNAL <miquel.raynal@bootlin.com> */
+
+/dts-v1/;
+#include "sun8i-r16-nintendo-nes-classic.dts"
+
+/ {
+ model = "Nintendo SuperNES Classic Edition";
+ compatible = "nintendo,super-nes-classic", "nintendo,nes-classic",
+ "allwinner,sun8i-r16", "allwinner,sun8i-a33";
+};
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins_parrot>;
- led1 {
+ led-1 {
label = "parrot:led1:usr";
- gpio = <&pio 4 17 GPIO_ACTIVE_HIGH>; /* PE17 */
+ gpios = <&pio 4 17 GPIO_ACTIVE_HIGH>; /* PE17 */
};
- led2 {
+ led-2 {
label = "parrot:led2:usr";
- gpio = <&pio 4 16 GPIO_ACTIVE_HIGH>; /* PE16 */
+ gpios = <&pio 4 16 GPIO_ACTIVE_HIGH>; /* PE16 */
};
};
};
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
/*
vref-supply = <®_aldo3>;
status = "okay";
- button@0 {
+ button-190 {
label = "V+";
linux,code = <KEY_VOLUMEUP>;
channel = <0>;
voltage = <190000>;
};
- button@1 {
+ button-390 {
label = "V-";
linux,code = <KEY_VOLUMEDOWN>;
channel = <0>;
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_parrot>;
vmmc-supply = <®_dcdc1>;
cd-gpios = <&pio 3 14 GPIO_ACTIVE_LOW>; /* PD14 */
bus-width = <4>;
&mmc1 {
pinctrl-names = "default";
- pinctrl-0 = <&mmc1_pins_a>, <&wifi_reset_pin_parrot>;
+ pinctrl-0 = <&mmc1_pg_pins>;
vmmc-supply = <®_aldo1>;
mmc-pwrseq = <&wifi_pwrseq>;
bus-width = <4>;
&mmc2_8bit_pins {
drive-strength = <40>;
- bias-pull-up;
};
&ohci0 {
status = "okay";
};
-&pio {
- mmc0_cd_pin_parrot: mmc0_cd_pin@0 {
- pins = "PD14";
- function = "gpio_in";
- bias-pull-up;
- };
-
- led_pins_parrot: led_pins@0 {
- pins = "PE16", "PE17";
- function = "gpio_out";
- };
-
- usb0_id_det: usb0_id_detect_pin@0 {
- pins = "PD10";
- function = "gpio_in";
- bias-pull-up;
- };
-
- usb1_vbus_pin_parrot: usb1_vbus_pin@0 {
- pins = "PD12";
- function = "gpio_out";
- };
-};
-
-&r_pio {
- wifi_reset_pin_parrot: wifi_reset_pin@0 {
- pins = "PL6";
- function = "gpio_out";
- };
-};
-
&r_rsb {
status = "okay";
axp22x: pmic@3a3 {
compatible = "x-powers,axp223";
reg = <0x3a3>;
- interrupt-parent = <&nmi_intc>;
+ interrupt-parent = <&r_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
drivevbus-supply = <®_vcc5v0>;
x-powers,drive-vbus-en;
};
®_usb1_vbus {
- pinctrl-names = "default";
- pinctrl-0 = <&usb1_vbus_pin_parrot>;
gpio = <&pio 3 12 GPIO_ACTIVE_HIGH>; /* PD12 */
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_b>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
&usbphy {
status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_det>;
usb0_vbus-supply = <®_drivevbus>;
- usb0_id_det-gpios = <&pio 3 10 GPIO_ACTIVE_HIGH>; /* PD10 */
+ usb0_id_det-gpios = <&pio 3 10 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PD10 */
usb0_vbus_power-supply = <&usb_power_supply>;
usb1_vbus-supply = <®_usb1_vbus>;
};
brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
default-brightness-level = <8>;
enable-gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
+ power-supply = <®_dc1sw>;
};
chosen {
*/
clock-frequency = <400000>;
- touchscreen: touchscreen@0 {
+ touchscreen: touchscreen@40 {
+ reg = <0x40>;
interrupt-parent = <&pio>;
interrupts = <1 5 IRQ_TYPE_EDGE_FALLING>; /* PB5 */
- pinctrl-names = "default";
- pinctrl-0 = <&ts_power_pin>;
power-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
/* Tablet dts must provide reg and compatible */
status = "disabled";
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
vmmc-supply = <®_dcdc1>;
bus-width = <4>;
cd-gpios = <&pio 1 4 GPIO_ACTIVE_LOW>; /* PB4 */
status = "okay";
};
-&pio {
- mmc0_cd_pin: mmc0_cd_pin@0 {
- pins = "PB4";
- function = "gpio_in";
- bias-pull-up;
- };
-
- ts_power_pin: ts_power_pin@0 {
- pins = "PH1";
- function = "gpio_out";
- };
-
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
- pins = "PH8";
- function = "gpio_in";
- bias-pull-up;
- };
-};
-
&r_rsb {
status = "okay";
axp22x: pmic@3a3 {
compatible = "x-powers,axp223";
reg = <0x3a3>;
- interrupt-parent = <&nmi_intc>;
+ interrupt-parent = <&r_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
eldoin-supply = <®_dcdc1>;
drivevbus-supply = <®_vcc5v0>;
};
&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_detect_pin>;
- usb0_id_det-gpio = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
+ usb0_id_det-gpios = <&pio 7 8 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH8 */
usb0_vbus_power-supply = <&usb_power_supply>;
usb0_vbus-supply = <®_drivevbus>;
status = "okay";
*/
#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
-
-&pio {
- ahci_pwr_pin_a: ahci_pwr_pin@0 {
- allwinner,pins = "PB8";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- usb0_vbus_pin_a: usb0_vbus_pin@0 {
- allwinner,pins = "PB9";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- usb1_vbus_pin_a: usb1_vbus_pin@0 {
- allwinner,pins = "PH6";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- usb2_vbus_pin_a: usb2_vbus_pin@0 {
- allwinner,pins = "PH3";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-};
/ {
reg_ahci_5v: ahci-5v {
compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&ahci_pwr_pin_a>;
regulator-name = "ahci-5v";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
reg_usb0_vbus: usb0-vbus {
compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_vbus_pin_a>;
regulator-name = "usb0-vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
reg_usb1_vbus: usb1-vbus {
compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&usb1_vbus_pin_a>;
regulator-name = "usb1-vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
reg_usb2_vbus: usb2-vbus {
compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&usb2_vbus_pin_a>;
regulator-name = "usb2-vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
#include "sunxi-common-regulators.dtsi"
&i2c0 {
pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
+ pinctrl-0 = <&i2c0_pins>;
status = "okay";
};
&i2c1 {
pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
+ pinctrl-0 = <&i2c1_pins>;
status = "okay";
};
vref-supply = <®_vcc3v0>;
status = "okay";
- button@200 {
+ button-200 {
label = "Volume Up";
linux,code = <KEY_VOLUMEUP>;
channel = <0>;
voltage = <200000>;
};
- button@400 {
+ button-400 {
label = "Volume Down";
linux,code = <KEY_VOLUMEDOWN>;
channel = <0>;
&pwm {
pinctrl-names = "default";
- pinctrl-0 = <&pwm0_pins>;
+ pinctrl-0 = <&pwm0_pin>;
status = "okay";
};
config VIDEO_LCD_PANEL_I2C_NAME
string "LCD panel i2c interface node name"
depends on VIDEO_LCD_PANEL_I2C
- default "i2c@0"
+ default "i2c"
---help---
Set the device tree node name for the LCD i2c interface.
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
-CONFIG_DEFAULT_DEVICE_TREE="sun8i-r16-nintendo-nes-classic-edition"
+CONFIG_DEFAULT_DEVICE_TREE="sun8i-r16-nintendo-nes-classic"
CONFIG_SPL=y
CONFIG_MACH_SUN8I_A33=y
CONFIG_DRAM_CLK=600
projects / u-boot.git / commitdiff
