ARM: dts: am57xx: Disable voltage switching for SD card

If UHS speed modes are enabled, a compatible SD card switches down to 1.8V
during enumeration. If after this a software reboot/crash takes place and
on-chip ROM tries to enumerate the SD card, the difference in
IO voltages (host @ 3.3V and card @ 1.8V) may end up damaging the card.

The fix for this is to have support for power cycling the card in
hardware (with a PORz/soft-reset line causing a power cycle of the card).
Because the beaglebone X15 (rev A,B and C), am57xx-evms and am57xx-idks don't
have this capability, disable voltage switching for these boards.

The major effect of this is that the maximum supported speed mode is now
high speed(50 MHz) down from SDR104(200 MHz).

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>

diff --git a/arch/arm/dts/am571x-idk.dts b/arch/arm/dts/am571x-idk.dts
index eb5fda81f5567679c89889f8a3b72c5e26776356..798fbfe19d403a75921749675c3da4f5e63bc8ab 100644 (file)
--- a/arch/arm/dts/am571x-idk.dts
+++ b/arch/arm/dts/am571x-idk.dts
@@ -102,14 +102,9 @@
 };
 
 &mmc1 {
-       pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104";
+       pinctrl-names = "default", "hs";
        pinctrl-0 = <&mmc1_pins_default_no_clk_pu>;
        pinctrl-1 = <&mmc1_pins_hs>;
-       pinctrl-2 = <&mmc1_pins_sdr12>;
-       pinctrl-3 = <&mmc1_pins_sdr25>;
-       pinctrl-4 = <&mmc1_pins_sdr50>;
-       pinctrl-5 = <&mmc1_pins_ddr50_rev20 &mmc1_iodelay_ddr50_conf>;
-       pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev20_conf>;
 };
 
 &mmc2 {

diff --git a/arch/arm/dts/am572x-idk.dts b/arch/arm/dts/am572x-idk.dts
index 224794855312118878f8736d40dc8adb95f31633..42e88c1bc08fa97cb5eb4e77c555c6ffc1f26bdc 100644 (file)
--- a/arch/arm/dts/am572x-idk.dts
+++ b/arch/arm/dts/am572x-idk.dts
@@ -21,14 +21,9 @@
 };
 
 &mmc1 {
-       pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104";
+       pinctrl-names = "default", "hs";
        pinctrl-0 = <&mmc1_pins_default_no_clk_pu>;
        pinctrl-1 = <&mmc1_pins_hs>;
-       pinctrl-2 = <&mmc1_pins_sdr12>;
-       pinctrl-3 = <&mmc1_pins_sdr25>;
-       pinctrl-4 = <&mmc1_pins_sdr50>;
-       pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_rev20_conf>;
-       pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev20_conf>;
 };
 
 &mmc2 {

diff --git a/arch/arm/dts/am57xx-beagle-x15-common.dtsi b/arch/arm/dts/am57xx-beagle-x15-common.dtsi
index 49aeecd312b4b10af2cb3badd68a4982fa8a921d..d6b94d528f483b5a5b916bae42ca2ade679ed96b 100644 (file)
--- a/arch/arm/dts/am57xx-beagle-x15-common.dtsi
+++ b/arch/arm/dts/am57xx-beagle-x15-common.dtsi
@@ -433,6 +433,7 @@
 
        bus-width = <4>;
        cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; /* gpio 219 */
+       no-1-8-v;
 };
 
 &mmc2 {

diff --git a/arch/arm/dts/am57xx-beagle-x15-revb1.dts b/arch/arm/dts/am57xx-beagle-x15-revb1.dts
index 5a77b334923d051f6943730b8d51849fe6161596..34c69965821bb5d20fe941d2cd5f95343f777338 100644 (file)
--- a/arch/arm/dts/am57xx-beagle-x15-revb1.dts
+++ b/arch/arm/dts/am57xx-beagle-x15-revb1.dts
@@ -19,14 +19,9 @@
 };
 
 &mmc1 {
-       pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104";
+       pinctrl-names = "default", "hs";
        pinctrl-0 = <&mmc1_pins_default>;
        pinctrl-1 = <&mmc1_pins_hs>;
-       pinctrl-2 = <&mmc1_pins_sdr12>;
-       pinctrl-3 = <&mmc1_pins_sdr25>;
-       pinctrl-4 = <&mmc1_pins_sdr50>;
-       pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_rev11_conf>;
-       pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev11_conf>;
        vmmc-supply = <&vdd_3v3>;
        vqmmc-supply = <&ldo1_reg>;
 };

diff --git a/arch/arm/dts/am57xx-beagle-x15-revc.dts b/arch/arm/dts/am57xx-beagle-x15-revc.dts
index 17c41da3b55f1c7d94460f98647f0fdb084a9dbe..ccd99160bbdfb869451f1a53001068369eb98936 100644 (file)
--- a/arch/arm/dts/am57xx-beagle-x15-revc.dts
+++ b/arch/arm/dts/am57xx-beagle-x15-revc.dts
@@ -19,14 +19,9 @@
 };
 
 &mmc1 {
-       pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104";
+       pinctrl-names = "default", "hs";
        pinctrl-0 = <&mmc1_pins_default>;
        pinctrl-1 = <&mmc1_pins_hs>;
-       pinctrl-2 = <&mmc1_pins_sdr12>;
-       pinctrl-3 = <&mmc1_pins_sdr25>;
-       pinctrl-4 = <&mmc1_pins_sdr50>;
-       pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_rev20_conf>;
-       pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev20_conf>;
        vmmc-supply = <&vdd_3v3>;
        vqmmc-supply = <&ldo1_reg>;
 };

diff --git a/arch/arm/dts/am57xx-idk-common.dtsi b/arch/arm/dts/am57xx-idk-common.dtsi
index fa5a078b27b2c837cbf11eded1b8be51f2807fb1..fdb4e0e47c724a0faa365afc1deba906013729e1 100644 (file)
--- a/arch/arm/dts/am57xx-idk-common.dtsi
+++ b/arch/arm/dts/am57xx-idk-common.dtsi
@@ -405,6 +405,7 @@
        vqmmc-supply = <&ldo1_reg>;
        bus-width = <4>;
        cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; /* gpio 219 */
+       no-1-8-v;
 };
 
 &mmc2 {