Michal Simek [Tue, 6 Sep 2022 10:41:10 +0000 (12:41 +0200)]
xilinx: zynq: Disable LMB for mini configurations
There shouldn't be a reason to have LMB on for these configurations.
LMB was already disabled for ZynqMP by commit 0063487a5b60 ("configs:
zynqmp: Disable LMB for mini u-boot").
Michal Simek [Wed, 7 Sep 2022 07:52:09 +0000 (09:52 +0200)]
cmd: bdinfo: Enable dumping lmb data when LMB is enabled
The commit 9996cea75f5a ("lmb/bdinfo: dump lmb info via bdinfo") added
support for dumping LMB information as the part of bdinfo. But code itself
should be called only when LMB is enabled.
fpga: zynq: Remove post config info message for SPL
The drivers informs the user that a post config was not run after FPGA
configuration. This message is unnecessary in SPL because the
ps7_post_config function is called via spl_board_prepare_for_boot
function before jump_to_image_no_args function from board_init_r
function.
Move arm twd timer driver from zynq to generic location.
DM timer drivers are designed differently to original driver. Timer is
counting up and not down.
Information about clock rates are find out in timer_pre_probe() that's
why there is no need to get any additional information from DT in the
driver itself (only register offset).
Tom Rini [Sat, 3 Sep 2022 01:51:21 +0000 (21:51 -0400)]
Merge branch '2022-09-02-assorted-improvements' into next
- DM RTC improvements that should help in CI, allow disabling LTO from
the make line, add extension (cape, etc) support to distro bootcmd,
add a pause command and re-enable ARM v4T support.
Simon Glass [Mon, 1 Aug 2022 13:58:48 +0000 (07:58 -0600)]
dm: rtc: Try to handle the localtime() race
At present the sandbox timer uses localtime() which can jump around twice
a year when daylight-saving time changes.
It would be tricky to make use of gmtime() since we still need to present
the time in local time, as seems to be required by U-Boot's RTC interface.
The problem can only happen once, so use a loop to detect it and try
again. This should be sufficient to detect either a change in the 'second'
value, or a daylight-saving change. We can assume that the latter also
incorporates a 'second' change, so there is no need to loop more than
twice.
Simon Glass [Mon, 1 Aug 2022 13:58:46 +0000 (07:58 -0600)]
dm: rtc: Avoid a race in the rtc_reset test
Since resetting the RTC on sandbox causes it to read the base time from
the system, we cannot rely on this being unchanged since it was last read.
Allow for a one-second delay.
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Fixes: https://source.denx.de/u-boot/u-boot/-/issues/4 Reported-by: Bin Meng <bmeng.cn@gmail.com> Reported-by: Tom Rini <trini@konsulko.com> Suggested-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 3 Aug 2022 18:13:08 +0000 (12:13 -0600)]
Makefile: Allow LTO to be disabled for a build
LTO (Link-Time Optimisation) is an very useful feature which can
significantly reduce the size of U-Boot binaries. So far it has been
made available for selected ARM boards and sandbox.
However, incremental builds are much slower when LTO is used. For example,
an incremental build of sandbox takes 2.1 seconds on my machine, but 6.7
seconds with LTO enabled.
Add a NO_LTO parameter to the build, similar to NO_SDL, so it can be
disabled during development if needed, for faster builds.
Add some documentation about LTO while we are here.
Sergei Antonov [Sun, 21 Aug 2022 13:34:20 +0000 (16:34 +0300)]
arm: ARMv4 assembly compatibility
There is currently a problem that U-Boot can not work on ARMv4
because assembly imlementations of memcpy() and some other functions
use "bx lr" instruction that is not available on ARMv4 ("mov pc, lr"
should be used instead).
A working preprocessor-based solution to this problem is found in
arch/arm/lib/relocate.S. Move it to the "ret" macro in
arch/arm/include/asm/assembler.h and change all "bx lr" code
to "ret lr" in functions that may run on ARMv4. Linux source code
deals with this problem in the same manner.
v1 -> v2:
Comment update. Pointed out by Andre Przywara.
Signed-off-by: Sergei Antonov <saproj@gmail.com> CC: Samuel Holland <samuel@sholland.org> CC: Ye Li <ye.li@nxp.com> CC: Simon Glass <sjg@chromium.org> CC: Andre Przywara <andre.przywara@arm.com> CC: Marek Vasut <marex@denx.de> CC: Sean Anderson <sean.anderson@seco.com> CC: Tom Rini <trini@konsulko.com>
This command is being introduced with the goal of allowing user-friendly
"generic use case" U-Boot builds to pause until user input under some
situations.
The main use case would be when a boot failure happens, to pause until
the user has had time to acknowledge the current state.
Tested using:
make && ./u-boot -v -T -c 'ut lib lib_test_hush_pause'
Signed-off-by: Samuel Dionne-Riel <samuel@dionne-riel.com> Cc: Simon Glass <sjg@chromium.org>
Introduce the new Kconfig symbol CONFIG_SPL_SYS_L2_PL310 to allow the
SPL to build cache-pl310.c.
Before this commit, the SPL could enable the PL310 L2 cache [1], but the
cache maintenance functions from cache-pl310.c were only useable for
non-SPL builds.
After enabling the cache one must be able to flush it, too. Thus this
commit allows cache-pl310.c to be included in the SPL build.
[1] See for example arch/arm/mach-imx/cache.c: v7_outer_cache_enable()
That means whenever an ARCH_MX6 board had SYS_L2_PL310 disabled, this
was correctly reflected in SYS_L2CACHE_OFF. Thus it's safe to insert
the 'select' statement under ARCH_MX6.
Tom Rini [Wed, 10 Aug 2022 14:29:28 +0000 (10:29 -0400)]
Remove CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_BITS et al
This removes the following symbols:
CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_BITS
CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_DELAY_MS
CONFIG_SYS_I2C_LDI_ADDR
CONFIG_SYS_I2C_DVI_ADDR
CONFIG_SYS_I2C_DVI_BUS_NUM
Andrew Davis [Tue, 26 Jul 2022 01:25:06 +0000 (20:25 -0500)]
firmware: ti_sci: Move ACK checking to ti_sci_do_xfer() function
We can check if the message was acknowledged in the common
ti_sci_do_xfer() which lets us remove it from after each call to this
function. This simplifies the code and reduces binary size.
Andrew Davis [Tue, 26 Jul 2022 01:25:05 +0000 (20:25 -0500)]
firmware: ti_sci: Remove inline keyword from functions
The inline hint is not needed here, the compiler will do the right thing
based on if we are compiling for speed or for code size. In this case the
inline causes this function to be placed inside each callsite which is
not the right thing to do for either speed nor size. There is no
performance benefit to this due to the larger function size reducing
cache locality, but there is a huge size penalty. Remove inline keyword.
Andrew Davis [Tue, 26 Jul 2022 01:25:03 +0000 (20:25 -0500)]
firmware: ti_sci: Reduce output on ti_sci_do_xfer error
This ti_sci_do_xfer() function already prints out the reason for the
failure, and the caller of each of these functions should also notify
the user of the failed task. Remove this extra level of error message.
arm: dts: qcom: Sync pinctrl DT nodes with Linux bindings
Currently for all Qcom SoCs/boards there are separate compatibles for
GPIO and pinctrl. But this is inconsistent with official (upstream) Linux
bindings which requires only a single compatible "qcom,<SoC name>-pinctrl"
and there is no such compatible property as "qcom,tlmm-<SoC name>".
So fix this inconsistency for Qcom SoCs in order to comply with upstream
DT bindings. This is done via removing compatibles from "msm_gpio" driver
and via binding to "msm_gpio" driver from pinctrl driver in case
"gpio-controller" property is specified for pinctrl node.
Suggested-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Sumit Garg [Thu, 4 Aug 2022 14:27:20 +0000 (19:57 +0530)]
board: qcs404-evb: Enable USB3 specific PMIC GPIO
For USB3 host controller to detect devices on the bus it is required to
enable a PMIC GPIO: usb_vbus_boost_pin. So enable that during board
specific initialization.
And since this PMIC GPIO parsing is quite u-boot specific, so add a
DT override to qcs404-evb-uboot.dtsi to represent usb_vbus_boost_pin.
Sumit Garg [Thu, 4 Aug 2022 14:27:18 +0000 (19:57 +0530)]
gpio: qcom_pmic: Add support for GPIO LV/MV subtype
GPIO LV (low voltage)/MV (medium voltage) subtypes have different
features and register mappings than 4CH/8CH subtypes. Add support
for LV and MV subtypes.
With GPIO LV/MV subtype available, add "qcom,pms405-gpio" compatible
which requires support for GPIO MV subtype.
Sumit Garg [Thu, 4 Aug 2022 14:27:17 +0000 (19:57 +0530)]
pmic: Convert pm8916 driver to a generic Qcom PMIC driver
Since both pm8916.c and pm8916_gpio.c are already supporting multiple
Qcom SoCs, it makes sense to rename these drivers to pmic_qcom.c and
qcom_pmic_gpio.c respectively. Also, these driver can be extended to
support additional functionality if required for other Qcom SoCs.
Along with this import latest DT binding: qcom,spmi-pmic.txt from Linux
kernel and thereby remove pm8916.txt.
Sumit Garg [Thu, 4 Aug 2022 14:27:16 +0000 (19:57 +0530)]
dts: qcs404-evb: Add USB controller and PHY nodes
QCS404 SoC provides support for two USB controllers: one USB3 and the
other one being USB2. The USB3 controller supports further 2 PHY: one high
speed PHY and the other super speed PHY. The USB2 controller supports a
single high speed PHY. So add corresponding DT nodes.
Sumit Garg [Thu, 4 Aug 2022 14:27:11 +0000 (19:57 +0530)]
reset: Convert ipq4019 driver to a generic Qcom driver
Since the base functionality remains the same for a reset driver on Qcom
SoCs, so leverage that to convert ipq4019 specific reset driver to a
generic Qcom reset driver. With that one just need to provide SoC specific
reset table.
Sumit Garg [Thu, 4 Aug 2022 14:27:10 +0000 (19:57 +0530)]
phy: Add support for drivers to enable USB on QCS404 SoC
QCS404 SoC supports two types of PHY, one supports high speed mode or
USB2 PHY and the other supports super speed mode or USB3 PHY. So add
corresponding PHY drivers.
- kirkwood: pogo_v4 & nsa310s: Add distro boot (Tony)
- kirkwood: add DM timer support and use it on lsxl boards (Michael)
- kirkwood: convert the Buffalo Linkstation LS-CHLv2 and XHL boards
to DM (Michael)
- mvebu: turris_mox/omnia: misc improments (Pali)
- mvebu: mbus: Fix mbus driver to work also after U-Boot relocation (Pali)
Michael Walle [Wed, 17 Aug 2022 19:38:08 +0000 (21:38 +0200)]
board: lsxl: disable eth0
The board has only one network interface. The linux kernel will
gracefully skip a the ethernet interface if no connected PHY could be
probed. u-boot on the other hand will throw an error message. The kernel
device tree is about to be fixed. For now, just disable the ethernet
interface in our -u-boot.dtsi.
Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Stefan Roese <sr@denx.de>
Michael Walle [Wed, 17 Aug 2022 19:38:06 +0000 (21:38 +0200)]
board: lsxl: convert to DM_SERIAL
DM_SERIAL needs early malloc. The on-chip RAM is pretty tight, it's only
2kiB, with DM_SERIAL enabled, this doesn't work anymore. Fortunately for
us, we don't need the on-chip RAM because the DRAM is already
initialized before u-boot starts. Just put the early malloc area there
and use the default early malloc size.
Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Stefan Roese <sr@denx.de>
Michael Walle [Wed, 17 Aug 2022 19:38:04 +0000 (21:38 +0200)]
board: lsxl: convert to DM_GPIO
Use the new mvebu GPIO driver and convert all the function calls to the
former kirkwood GPIO driver. This means that we are now using the LED
uclass and the regulator uclass. Unfortunately, the GPIO LED doesn't
offer a blinking method. Thus we are now stuck with solid on and off
states, which makes debugging a bit harder. Also, there is no GPIO fan
driver for now.
Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Stefan Roese <sr@denx.de>
Michael Walle [Wed, 17 Aug 2022 19:38:03 +0000 (21:38 +0200)]
board: lsxl: make last resort recovery more reliable
If something is wrong with the environment, we cannot rely on a proper
u-boot operation anymore. In fact, it is possible, that we never reach
misc_init_r() with a broken environment.
Also don't enable the netconsole by environment settings. This way the
user don't have to reconfigure the environment. Instead the network
console is only enabled when the push button is pressed during boot.
Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Wed, 17 Aug 2022 19:37:49 +0000 (21:37 +0200)]
arm: kirkwood: 88f6281: Detect CONFIG_SYS_TCLK from SAR register
Bit 21 in SAR register specifies if TCLK is running at 166 MHz or 200 MHz.
This information is undocumented in public Marvell Kirkwood Functional
Specifications [2], but is available in Linux v3.15 kirkwood code [1].
Commit 8ac303d49f89 ("arm: kirkwood: Do not overwrite CONFIG_SYS_TCLK")
broke support for Marvell 88F6281 SoCs because it was expected that all
those SoCs have TCLK running at 200 MHz as specified in Marvell 88F6281
Hardware Specifications [3].
Fix broken support for 88F6281 by detecting CONFIG_SYS_TCLK from SAR
register, like it was doing Linux v3.15.
Michael Walle [Wed, 17 Aug 2022 19:37:48 +0000 (21:37 +0200)]
time: move the CONFIG_SYS_TIMER_RATE handling to the compiler
CONFIG_SYS_TIMER_RATE might be a dynamic value, i.e. a function call
instead of a static value, thus it has to be evaluated at runtime. If it
is a static value, the compiler should be able to optimize the unused
branches out.
This will be needed for kirkwoods dynamic CONFIG_SYS_TCLK setting.
Cc: Pali Rohár <pali@kernel.org> Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
- Add distro boot to board include file and deconfig file
- Miscellaneous changes:
- Remove Gerald from maintainer list (email bounced)
- Add CONFIG_SUPPORT_PASSING_ATAGS and friends to support legacy
kernel method of booting (e.g. OpenWrt) with appended DTB.
- Add CONFIG_UBIFS_SILENCE_MSG to reduce binary size.
Note that this patch is depended on the following patch:
https://patchwork.ozlabs.org/project/uboot/patch/20220807192709.21717-1-pali@kernel.org/
Pali Rohár [Wed, 10 Aug 2022 12:46:09 +0000 (14:46 +0200)]
arm: mvebu: mbus: Fix mbus driver to work also after U-Boot relocation
mbus driver is initialized from arch_cpu_init() callback which is called
before relocation. This driver stores lot of functions and structure
pointers into global variables, so it is data position dependent.
Therefore after relocations all pointers are invalid and driver does not
work anymore as all pointers referes to the old memory, which overlaps with
CONFIG_SYS_LOAD_ADDR and ${loadaddr}.
For example U-Boot fuse command crashes if loadaddr memory is cleared or
rewritten by some image loaded by U-Boot load command.
mw.w ${loadaddr} 0x0 10000
fuse read 0 1 2
Fix this issue by removing of all mbus global variables in which are stored
pointers to structures or functions which changes during relocation. And
replace it by direct function calls (not via pointers). With this change
fuse command finally works.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Wed, 10 Aug 2022 10:54:11 +0000 (12:54 +0200)]
arm: mvebu: turris_mox: Set "sfp" label in eth1 DT node when only Mox SFP is detected
When Mox SFP module is connected after Topaz or Peridot module then port DT
node already contains "sfp" label. But Mox SFP module can be connected also
without Topaz or Peridot module in which case it is connected directly into
he eth1 DT node, which is without any label. So add "sfp" label into eth1
DT node in this case.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <kabel@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Wed, 10 Aug 2022 09:00:25 +0000 (11:00 +0200)]
arm: mvebu: turris_omnia: Show MCU version
There are already more MCU firmware versions for Turris Omnia in
production, so display git commit (version) of the MCU firmware during
U-Boot startup. It will help to identify what version of MCU firmware is
Turris Omnia using.
MCU firmware for Turris Omnia is open source and available at website:
https://gitlab.nic.cz/turris/hw/omnia_hw_ctrl
It can be updated from running system via i2c bus with this tool:
https://gitlab.nic.cz/turris/omnia-mcutool
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
- Add distro boot to board include file and deconfig file
- Miscellaneous changes:
- Add CONFIG_SUPPORT_PASSING_ATAGS and friends to support legacy
kernel method of booting (e.g. OpenWrt) with appended DTB.
- Add CONFIG_LTO and CONFIG_UBIFS_SILENCE_MSG, and disable some
unused configs to reduce binary size.
Note that this patch is depended on the following patch:
https://patchwork.ozlabs.org/project/uboot/patch/20220807192709.21717-1-pali@kernel.org/
Pali Rohár [Mon, 8 Aug 2022 17:13:43 +0000 (19:13 +0200)]
arm: mvebu: Define env_sf_get_env_addr() for all Armada boards in SPL
SPI0 CS0 Flash is mapped to address range 0xD4000000 - 0xD7FFFFFF by BootROM.
Proper U-Boot removes this direct mapping. So it is available only in SPL.
This applies for all 32-bit Armada BootROMs. SPL mvebu code is used only on
32-bit Armada SoCs. So move env_sf_get_env_addr() function from Turris
Omnia board to common SPL mvebu code and add proper checks for SPI0 CS0.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Tom Rini [Wed, 10 Aug 2022 01:08:54 +0000 (21:08 -0400)]
CI: Move to Ubuntu 2022.04 "Jammy" for CI base
- We now have a new enough sbsigntools in the distro, stop building.
- Use the 20220801 tag for Jammy.
- Move to pygit2 1.9.2 (current version) as the old one doesn't build on
"Jammy".
- Add the working directory to the list of safe directories for git.
- Move to pytest 6.2.5 to address other issues.
- This move exposed a number of minor issues in the existing scripts we
used within CI to perform the jobs themselves. The most notable changes
here involve using 'set +e / set -e' to enforce when we should or should
not make non-zero buildman status be a fatal error.
Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Pali Rohár [Fri, 19 Aug 2022 09:20:01 +0000 (11:20 +0200)]
mtd: rawnand: fsl_elbc: Fix reading address pointer from DT
During compilation gcc throws warning:
drivers/mtd/nand/raw/fsl_elbc_nand.c: In function ‘fsl_elbc_nand_probe’:
drivers/mtd/nand/raw/fsl_elbc_nand.c:841:31: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
return fsl_elbc_chip_init(0, (void *)dev_read_addr(dev), dev);
^
Fix it by using dev_read_addr_ptr() function which returns pointer instead
of dev_read_addr() which returns integer type.
Pali Rohár [Mon, 15 Aug 2022 08:01:40 +0000 (10:01 +0200)]
mtd: rawnand: fsl_elbc: Remove NAND_NO_SUBPAGE_WRITE flag
Subpage write support for freescale eLBC NAND controller driver is
implemented in U-Boot and was fixes in the commit d3963721d93f ("nand: Sync
with Linux v4.1").
So remove NAND_NO_SUBPAGE_WRITE flag from the fsl_elbc_nand.c driver. This
partially revert commit cb04c7723429 ("nand/fsl: add NAND_NO_SUBPAGE_WRITE
to eLBC and IFC drivers"), only eLBC driver part.
With this change U-Boot with default settings can read from NAND UBIFS
image created on Linux with Linux default settings. Prior this change
U-Boot was unable to read from NAND UBIFS images created with Linux default
settings due to differnet UBI geometry.
Linux kernel fsl_elbc_nand.c driver also does not set NAND_NO_SUBPAGE_WRITE
flag and has implemented subpage write support.
Fixes: cb04c7723429 ("nand/fsl: add NAND_NO_SUBPAGE_WRITE to eLBC and IFC drivers") Fixes: d3963721d93f ("nand: Sync with Linux v4.1") Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com> Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com> Acked-By: Michael Trimarchi<michael@amarulasolutions.com> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
On some nand controllers with hw-ecc the controller code wants to know
the ecc strength and size and having these as 0, 0 is not accepted.
Specifying these in devicetree is possible but undesirable as the nand
may be different in different production runs of the same board, so it
is better to get this info from the nand id where possible.
This commit adds code to read the ecc strength and size from the nand
for Samsung extended-id nands. This code is based on the info for the 5th
id byte in the datasheets for the following Samsung nands: K9GAG08U0E,
K9GAG08U0F, K9GAG08X0D, K9GBG08U0A, K9GBG08U0B. These all use these bits
in the exact same way.
Holger Brunck [Fri, 19 Aug 2022 14:55:06 +0000 (16:55 +0200)]
powerpc: remove support for kmtergr1 and MPC8309
The kmtegr1 board is out of maintenance and can be removed. As it is the
only board in the tree using MPC8309 the support for this CPU is dropped
completely.
Enforce requiring DM_ETH to be enabled for ethernet drivers, as the
migration deadline has well passed. To facilitate this, we remove some
non-migrated platforms and disable networking on a few others. Finally
we remove some of the now-useless non-DM_ETH code in some platforms as a
prerequisite for DM_ETH being set.
Tom Rini [Tue, 2 Aug 2022 11:33:47 +0000 (07:33 -0400)]
net: Make DM_ETH be selected by NETDEVICE
The deadline for DM_ETH migration passed 2 years ago. Now that
platforms which cannot be migrated have been either removed or had
drivers disabled, and platforms that needed minor help to migrate have
been forcefully migrated, we can complete the migration.
This entails select'ing DM_ETH under NETDEVICES, and then removing now
extraneous depends on lines. In a few places, we can now either remove
options or just simplify later dependencies.
Cc: Ramon Fried <rfried.dev@gmail.com> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Ramon Fried <rfried.dev@gmail.com>
projects / u-boot.git / log
