Scott Wood [Fri, 12 Oct 2012 23:02:24 +0000 (18:02 -0500)]
powerpc/mpc85xx/p2020rdb-pca: Use L2 SRAM for SPL boot
This allows DDR configuration to be deferred to the final U-Boot image,
which is able to make use of SPD data. The SPL itself cannot use SPD due
to code size constraints. It previously used fixed register values for
DDR configuration, and those values did not work on the p2020rdb-pca
board I tested with. It's possible that different revisions of the board
require different settings. Using SPD eliminates that problem.
Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Andy Fleming <afleming@freescale.com>
Scott Wood [Wed, 3 Oct 2012 00:35:18 +0000 (19:35 -0500)]
powerpc/mpc85xx/p1_p2_rdb_pc: clean up memory map
- Sort by address, and fix column alignment
- Don't label things as localbus that aren't. Instead, put chipselect
info at the end of the description for localbus windows. Note that
NAND/NOR have their chipselects swapped when booting from NAND, and CS2
can be either PMC or VSC7385 depending on hwconfig.
- Shrink NAND to the 32K that's actually mapped in the localbus
- Assign an address and size to L2 SRAM. Remove the similarly named
but unintelligible "L2 SDRAM(REV.)".
- Remove the untrue comment about L1 stack being mapped with TLB0.
Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Andy Fleming <afleming@freescale.com>
Scott Wood [Fri, 21 Sep 2012 23:35:27 +0000 (18:35 -0500)]
spl/nand: config symbol documentation
Document parameters used for specifying the NAND image to be loaded.
Also fix the definition of CONFIG_SPL_NAND_SIMPLE -- it's only
nand_spl_simple.c, not the entire nand directory. The word "simple" is
there for a reason. :-)
Signed-off-by: Scott Wood <scottwood@freescale.com>
---
v2: updated for makefile changes earlier in patchset
Scott Wood [Fri, 21 Sep 2012 00:09:07 +0000 (19:09 -0500)]
spl/nand: introduce CONFIG_SPL_NAND_DRIVERS, _BASE, and _ECC.
Some small SPLs do not use nand_base.c, and a subset of those also
require a special driver. Some SPLs need software ECC but others can't
fit it.
All existing boards that specify CONFIG_SPL_NAND_SUPPORT have these
symbols added to preserve existing behavior.
Signed-off-by: Scott Wood <scottwood@freescale.com>
--
v2: use positive logic for including bits of NAND, rather than
a MINIMAL symbol that excludes things.
Scott Wood [Fri, 21 Sep 2012 00:02:18 +0000 (19:02 -0500)]
spl/85xx: new SPL support
Update CONFIG_RAMBOOT and CONFIG_NAND_SPL references to accept CONFIG_SPL
and CONFIG_SPL_BUILD, respectively. CONFIG_NAND_SPL can be removed once
the last mpc85xx nand_spl target is gone.
CONFIG_RAMBOOT will need to remain for other use cases, but it doesn't
seem right to overload it for meaning SPL as well as nand_spl does. Even
if it's somewhat appropriate for the main u-boot, the SPL itself isn't
(necessarily) ramboot, and we don't have separate configs for SPL and
main u-boot. It was also inconsistent, as other platforms such as
mpc83xx didn't use CONFIG_RAMBOOT in this way.
Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Andy Fleming <afleming@freescale.com>
Scott Wood [Thu, 20 Sep 2012 21:35:21 +0000 (16:35 -0500)]
spl/powerpc: introduce CONFIG_SPL_INIT_MINIMAL
cpu_init_nand.c is renamed to spl_minimal.c as it is not really NAND-specific.
Signed-off-by: Scott Wood <scottwood@freescale.com>
---
v2: factor out START, and change cpu_init_nand.c to spl_minimal.c Cc: Andy Fleming <afleming@freescale.com>
Scott Wood [Sat, 18 Aug 2012 00:46:29 +0000 (19:46 -0500)]
spl/mpc85xx: move udelay to cpu code
It applies to non-Freescale 85xx boards as well as Freescale boards,
so it doesn't belong in board/freescale. Plus, it needs to come out
of nand_spl if it's to be used by the new SPL.
Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Andy Fleming <afleming@freescale.com>
Scott Wood [Thu, 20 Sep 2012 23:34:49 +0000 (18:34 -0500)]
powerpc/mpc85xx: fix TLB alignment
In the RAMBOOT/SPL case we were creating a TLB entry starting at
CONFIG_SYS_MONITOR_BASE, and just hoping that the base was properly
aligned for the TLB entry size. This turned out to not be the case
with NAND SPL because the main U-Boot starts at an offset into the image
in order to skip the SPL itself.
Fix the TLB entry to always start at a proper alignment. We still assume that
CONFIG_SYS_MONITOR_BASE doesn't start immediately before a large-page boundary
thus requiring multiple TLB entries.
Signed-off-by: Scott Wood <scottwood@frescale.com> Cc: Andy Fleming <afleming@freescale.com>
Scott Wood [Fri, 21 Sep 2012 00:10:01 +0000 (19:10 -0500)]
powerpc: change .fixup test to a GCC version test
This was introduced by commit 244615197469dd6fe75ae082f38424b97c79aeaf, but it
fails in a minimal SPL build where the only thing in arch/powerpc/lib is
cache.c, which apparently doesn't generate any fixup records.
The problem is reported to occur with GCC 3.x, so insist on GCC 4.0 or newer.
Patterned after checkthumb as suggested by Tom Rini.
Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Peter Tyser <ptyser@xes-inc.com> Cc: Tom Rini <trini@ti.com>
--
v2: test gcc version instead of testing nothing
Scott Wood [Fri, 21 Sep 2012 21:27:32 +0000 (16:27 -0500)]
spl: introduce CONFIG_SPL_TARGET
Currently the SPL target is specified in a CPU-specific makefile
fragment. While some targets may need something more complicated than a
simple target name, targets which don't need this shouldn't have to provide a makefile fragment just for this.
Signed-off-by: Scott Wood <scottwood@freescale.com>
---
v2: Removed default target as it's been pointed out to me how existing platforms
cause the SPL to be built.
Samsung's S3C24XX SoCs need this in order to generate a binary image
with a padded SPL concatenated with U-Boot.
Signed-off-by: José Miguel Gonçalves <jose.goncalves@inov.pt>
[scottwood@freescale.com: fixed prereq of u-boot.ubl] Signed-off-by: Scott Wood <scottwood@freescale.com>
--
v2: Removed spl/ prefix from u-boot.ubl prerequisite.
Scott Wood [Fri, 26 Oct 2012 00:27:41 +0000 (19:27 -0500)]
powerpc/mpc85xx: move debug tlb entry after TLB is in known state
Previously, in many if not all configs we were creating overlapping TLB entries
which is illegal. This caused a crash during boot when moving p2020rdb NAND SPL
into L2 SRAM.
Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Prabhakar Kushwaha <prabhakar@freescale.com> Cc: Andy Fleming <afleming@freescale.com>
--
Prabhakar, please test that debug still works.
Scott Wood [Tue, 18 Sep 2012 23:19:05 +0000 (18:19 -0500)]
serial/ns16550: wait for TEMT before initializing
TEMT is set when the transmitter is totally empty and all output has
finished.
This prevents output problems (including a loss of synchronization
observed on p2020 that persisted for quite a while) if SPL has output
still on its way out.
Signed-off-by: Scott Wood <scottwood@freescale.com>
--
v2: fixed typo in subject, and explained what the bit does in the changelog
Scott Wood [Tue, 16 Oct 2012 20:43:15 +0000 (15:43 -0500)]
serial/ns16550: don't build serial_ns16550 with MIN_FUNCTIONS
CONFIG_NS16550_MIN_FUNCTIONS is used by small SPLs to gain access to basic
ns16550 output code without pulling in things not needed by the SPL.
This previously only worked with non-MULTI configs. Recently MULTI was
made mandatory, and MIN_FUNCTIONS fails like this:
drivers/serial/libserial.o: In function `calc_divisor.clone.0':
serial_ns16550.c:(.text.calc_divisor.clone.0+0x24): undefined reference to `get_bus_freq'
drivers/serial/libserial.o: In function `_serial_getc':
(.text._serial_getc+0x30): undefined reference to `NS16550_getc'
drivers/serial/libserial.o: In function `_serial_tstc':
(.text._serial_tstc+0x30): undefined reference to `NS16550_tstc'
drivers/serial/libserial.o: In function `_serial_setbrg':
(.text._serial_setbrg+0x3c): undefined reference to `NS16550_reinit'
make[1]: *** [/tmp/u-boot/spl/u-boot-spl] Error 1
make: *** [/tmp/u-boot/spl/u-boot-spl.bin] Error 2
With MIN_FUNCTIONS we don't need anything from this file, so don't build
it. The conditional needs to be in the file itself rather than the
makefile, because the config symbols are only imported to the makefiles
once, not separately for the SPL phase of the build.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Alejandro Mery [Wed, 31 Oct 2012 08:21:33 +0000 (08:21 +0000)]
fs: zfs: fix illegal use of fp
the upcoming sunxi (allwinner a10/a13) platform enables zfs
by default, and using linaro's hf -msoft-float makes the build
fail because this u64 division.
Signed-off-by: Alejandro Mery <amery@geeks.cl> Acked-by: Stefan Roese <sr@denx.de>
M68K: eb_cpu5282: general update and enhanced board support
- update clock settings for higher perfomance
- change standard baud rate to 115200
- fix flash base address
- remove unused defines
- add I2C support
- switch form board dependent flash to cfi
- remove board dependent flash code
- use sdram bank 0 instead of bank 1 on boot
- enable on board frame buffer instead external
- remove fake mac address form config
- add watchdog support
- add status led support
Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
[agust: fixed small style issues and build warning] Signed-off-by: Anatolij Gustschin <agust@denx.de>
Łukasz Majewski [Tue, 13 Nov 2012 03:22:12 +0000 (03:22 +0000)]
pmic: Extend PMIC framework to support battery related commands
Two extra commands:
"pmic name bat state" and "pmic name bat charge" has been added to
pmic framework. Those provides state display and charge capabilities
to named batteries.
The pmic_core.c file has been refactored to more consistent name scheme.
Łukasz Majewski [Tue, 13 Nov 2012 03:22:03 +0000 (03:22 +0000)]
pmic:fuel-gauge: Support for MAX17042 fuel-gauge
Support for MAX17042 fuel-gauge (FG), which is built into the MAX8997
power management device.
Special file - fg_battery_cell_params.h with cells characteristics
added.
The FG device will work with redesigned PMIC framework.
Łukasz Majewski [Tue, 13 Nov 2012 03:22:01 +0000 (03:22 +0000)]
pmic:battery: Support for Trats Battery at PMIC framework
Trats battery is now treated in the same way as other power related
devices. This approach allows for more unified handling of all devices
responsible for power management.
Łukasz Majewski [Tue, 13 Nov 2012 03:21:56 +0000 (03:21 +0000)]
pmic: Introduce power_init_board() method at ./lib/board.c file
It is necessary to introduce a new system wide function- power_init_board()
It turns out, that power initialization must be done as early as possible.
In the case of PMIC framework redesign, which aims to support multiple
instances of PMIC devices the initialization shall be performed just
after malloc configuration.
The power_init_board function is a weak function with default implementation.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Łukasz Majewski [Tue, 13 Nov 2012 03:21:55 +0000 (03:21 +0000)]
pmic: Extend PMIC framework to support multiple instances of PMIC devices
The PMIC framework has been extended to support multiple instances of
the variety of devices responsible for power management.
This change allows supporting of e.g. fuel gauge, charger, MUIC (Micro USB
Interface Circuit).
Power related includes have been moved to ./include/power directory.
This is a first of a series of patches - in the future "pmic" will be
replaced with "power".
Two important issues:
1. The PMIC needs to be initialized just after malloc is configured
2. It uses list to hold information about available PMIC devices
Scott Wood [Tue, 13 Nov 2012 12:30:39 +0000 (12:30 +0000)]
nand_spl: fix u-boot.lst breakage
Commit 97b24d3d51a92cb8c0c1e1a74abf22fe1a1807a3 "common: Add symbol
handling for generic lists into Makefile" introduced build errors in many
nand_spl targets, complaining of a missing u-boot.lst. When not doing an
out-of-tree build, $(obj) expands to nothing, so GCC ended up being given
-I with no argument (or rather, -ansi was the argument). The failure
didn't show up during a -j1 build because it was picking up the non-SPL
version of u-boot.lst.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Simon Glass [Tue, 30 Oct 2012 06:15:16 +0000 (06:15 +0000)]
patman: Issue empty change logs for unchanged patches
Often a particular patch may change only for some versions of a series.
For versions where there is no change, issue a change log indicating
that (for example 'Changes in v4: None').
For such lines, don't add a blank line afterwards, to conserve space.
Use list.insert() instead of list = [item] + list.
Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Stefan Roese <sr@denx.de>
Thomas Chou [Mon, 5 Nov 2012 04:51:54 +0000 (12:51 +0800)]
nios2: remove asm/status_led.h
The file has a wrong inline keyword of __led_toggle(), which causes
compilation error. And its content is defined in common status_led.h.
So define CONFIG_BOARD_SPECIFIC_LED in board config files and remove
this header file.
Thomas Chou [Fri, 9 Nov 2012 06:29:15 +0000 (14:29 +0800)]
nios2: use builtin functions for control registers access
The commit 51926d5ee0be029fb45f10f42756df97279f8ad3
COMMON: Use __stringify() instead of rest of implementations
forgot to update the wrctl funtion, and causes compilation error.
But there are builtin functions for control registers access in
nios2 comipiler. It is convenient to use them instead.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Cc: Marek Vasut <marex@denx.de>
common/command.c: revert changes from commit 199adb60
commit 199adb601ff34bdbbd0667fac80dfe0a87bffc2b "common/misc: sparse
fixes" broke the help command trying to fix the sparse error
"command.c:44:38: error: bad constant expression".
As Henrik points out, the fix was bad because the commit used
CONFIG_SYS_MAXARGS whereas the code intended to use the maximum
number of commands (not arguments to a command).
Revert command.c changes to the original code as asked by Wolfgang.
Reported-by: Henrik Nordström <henrik@henriknordstrom.net> Signed-off-by: Anatolij Gustschin <agust@denx.de>
Michal Simek [Wed, 26 Sep 2012 12:24:05 +0000 (14:24 +0200)]
microblaze: Fix compilation failure because of missing libdts
Microblaze platform can use CONFIG_OF_EMBED option
but also it is necessary to support boards
which don't want to use this option.
U-Boot doesn't compile dts/libdts.o for #undef CONFIG_OF_EMBED
case that's why it should be guarded by ifdef.
Introduced a lot of compilation failures with unknow types.
include/linux/byteorder/big_endian.h:45:1: error: unknown type name '__le64'
include/linux/byteorder/big_endian.h: In function '__cpu_to_le64p':
include/linux/byteorder/big_endian.h:47:18: error: '__le64' undeclared (first use in this function)
include/linux/byteorder/big_endian.h:47:18: note: each undeclared identifier is reported only once for each function it appears in
include/linux/byteorder/big_endian.h:47:25: error: expected ';' before '__swab64p'
include/linux/byteorder/big_endian.h: At top level:
include/linux/byteorder/big_endian.h:49:1: error: unknown type name '__le64'
include/linux/byteorder/big_endian.h:53:1: error: unknown type name '__le32'
include/linux/byteorder/big_endian.h: In function '__cpu_to_le32p':
include/linux/byteorder/big_endian.h:55:18: error: '__le32' undeclared (first use in this function)
include/linux/byteorder/big_endian.h:55:25: error: expected ';' before '__swab32p'
include/linux/byteorder/big_endian.h: At top level:
include/linux/byteorder/big_endian.h:57:1: error: unknown type name '__le32'
include/linux/byteorder/big_endian.h:61:1: error: unknown type name '__le16'
...
Michal Simek [Wed, 26 Sep 2012 12:42:38 +0000 (14:42 +0200)]
microblaze: Fix compilation warning in ext2_find_next_zero_bit
ext2_find_next_zero_bit must be also static if __swab32 is also static.
Warning:
include/asm/bitops.h:369:22: warning: '__fswab32' is static but
used in inline function 'ext2_find_next_zero_bit'
which is not static [enabled by default]
Signed-off-by: Michal Simek <monstr@monstr.eu> Acked-by: Stephan Linz <linz@li-pro.net>
video: Skip bitmaps which do not fit into the screen in cfb_console
The cfb console driver is trying to prevent bitmaps to spill over the
screen, but the calculations assume that at least part of the bitmap
fits into the screen area. In reality there could be bitmap elements
which are completely out of the screen area, they just need to be
discarded.
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org> Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Che-Liang Chiou <clchiou@chromium.org>
[agust: fix some minor style issues and build warnings] Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tom Wai-Hong Tam [Fri, 28 Sep 2012 15:11:14 +0000 (15:11 +0000)]
lcd: Fix BMP decode bug that skips the wrong padded row
This change fixed 2 things:
- Rename padded_line to padded_width since it is (width + padded_row) not line.
- When finished a line, should skip the padded_row that is
(padded_width - width) instead of (width - padded_width).
Reference: http://en.wikipedia.org/wiki/BMP_file_format Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Stefan Reinauer [Fri, 28 Sep 2012 15:11:11 +0000 (15:11 +0000)]
video: Provide an API to access video parameters
Create a basic API to provide access to video parameters such as screen
size, and to position the cursor on the screen. Also add a prototype
for video_display_bitmap() which was missing.
Signed-off-by: Stefan Reinauer <reinauer@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Anatolij Gustschin <agust@denx.de>
Liu Ying [Sat, 6 Oct 2012 04:16:04 +0000 (04:16 +0000)]
ipu common: reset ipuv3 correctly
This patch checks self-clear sw_ipu_rst bit in
SCR register of SRC controller to be cleared
after setting it to high to reset IPUv3. This
makes sure that IPUv3 finishes sofware reset.
A timeout mechanism is added to stop polling
on the bit status in case the bit could not be
cleared by the hardware automatically within
10 millisecond.
Wolfgang Denk [Mon, 5 Nov 2012 00:50:54 +0000 (17:50 -0700)]
Makefile: use EXTRAVERSION for -rc? tag
When using SUBLEVEL for the -rc? tag, this results in an ugly version
string like "2013.01.-rc1" - let's use EXTRAVERSION instead to get the
simple "2013.01-rc1"
Signed-off-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Wed, 31 Oct 2012 13:30:41 +0000 (13:30 +0000)]
usb gadget ether: Fix warning in is_eth_addr_valid()
The gadget ethernet driver needs to keep copies of the MAC address (at
both endpoints) as strings so it needs a custom function for validation
of the MAC. It was not however performing a totally correct check and
also was emitting a warning about a set but unused variable. The
solution to both is that after checking the string contents we use the
standard test for a valid MAC.
Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Marek Vasut <marex@denx.de> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Kim Phillips [Mon, 29 Oct 2012 13:34:46 +0000 (13:34 +0000)]
drivers/mtd/nand: sparse fixes
nand_ecc.c:82:5: warning: symbol 'nand_calculate_ecc' was not declared. Should it be static?
nand_ecc.c:155:5: warning: symbol 'nand_correct_data' was not declared. Should it be static?
nand_base.c:2854:1: error: directive in argument list
nand_base.c:2856:1: error: directive in argument list
Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Acked-by: Scott Wood <scottwood@freescale.com>
Kim Phillips [Mon, 29 Oct 2012 13:34:45 +0000 (13:34 +0000)]
drivers/mtd/cfi_flash.c: sparse fixes
cfi_flash.c:756:43: warning: Using plain integer as NULL pointer
cfi_flash.c:1150:52: warning: cast to non-scalar
cfi_flash.c:1433:46: warning: cast truncates bits from constant value (890089 becomes 89)
cfi_flash.c:1490:61: warning: cast truncates bits from constant value (1f001f becomes 1f)
cfi_flash.c:1508:61: warning: cast truncates bits from constant value (10001 becomes 1)
cfi_flash.c:1738:63: warning: cast truncates bits from constant value (10001 becomes 1)
cfi_flash.c:1857:6: warning: symbol '__flash_cmd_reset' was not declared. Should it be static?
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Kim Phillips [Mon, 29 Oct 2012 13:34:44 +0000 (13:34 +0000)]
drivers/mmc/fsl_esdhc.c: sparse fixes
fsl_esdhc.c:71:6: warning: symbol 'esdhc_xfertyp' was not declared. Should it be static?
fsl_esdhc.c:413:6: warning: symbol 'set_sysctl' was not declared. Should it be st
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Kim Phillips [Mon, 29 Oct 2012 13:34:43 +0000 (13:34 +0000)]
drivers/mmc/mmc.c: sparse fixes
mmc.c:137:5: warning: symbol 'mmc_send_cmd' was not declared. Should it be static?
mmc.c:203:5: warning: symbol 'mmc_send_status' was not declared. Should it be static?
mmc.c:247:5: warning: symbol 'mmc_set_blocklen' was not declared. Should it be static?
mmc.c:440:5: warning: symbol 'mmc_read_blocks' was not declared. Should it be static?
mmc.c:510:5: warning: symbol 'mmc_go_idle' was not declared. Should it be static?
mmc.c:532:1: warning: symbol 'sd_send_op_cond' was not declared. Should it be static?
mmc.c:597:5: warning: symbol 'mmc_send_op_cond' was not declared. Should it be static?
mmc.c:661:5: warning: symbol 'mmc_send_ext_csd' was not declared. Should it be static?
mmc.c:683:5: warning: symbol 'mmc_switch' was not declared. Should it be static?
mmc.c:705:5: warning: symbol 'mmc_change_freq' was not declared. Should it be static?
mmc.c:775:5: warning: symbol 'sd_switch' was not declared. Should it be static?
mmc.c:796:5: warning: symbol 'sd_change_freq' was not declared. Should it be static?
mmc.c:935:6: warning: symbol 'mmc_set_ios' was not declared. Should it be static?
mmc.c:953:6: warning: symbol 'mmc_set_bus_width' was not declared. Should it be static?
mmc.c:1108:26: warning: dubious: !x & y
mmc.c:960:5: warning: symbol 'mmc_startup' was not declared. Should it be static?
mmc.c:1243:5: warning: symbol 'mmc_send_if_cond' was not declared. Should it be s
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Kim Phillips [Mon, 29 Oct 2012 13:34:41 +0000 (13:34 +0000)]
drivers/gpio/mpc83xx_gpio.c: sparse fixes
mpc83xx_gpio.c:166:26: warning: non-ANSI function declaration of function 'mpc83xx_gpio_init_f'
mpc83xx_gpio.c:190:26: warning: non-ANSI function declaration of function 'mpc83xx_gpio_init_r'
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Kim Phillips [Mon, 29 Oct 2012 13:34:40 +0000 (13:34 +0000)]
drivers/block/: sparse fixes
sata_sil.c:371:7: warning: symbol 'sil_sata_rw_lba28' was not declared. Should it be static?
sata_sil.c:399:7: warning: symbol 'sil_sata_rw_lba48' was not declared. Should it be static?
sata_sil.c:429:6: warning: symbol 'sil_sata_cmd_flush_cache' was not declared. Should it be static?
sata_sil.c:441:6: warning: symbol 'sil_sata_cmd_flush_cache_ext' was not declared. Should it be static?
sata_sil.c:489:7: warning: symbol 'sata_read' was not declared. Should it be static?
sata_sil.c:505:7: warning: symbol 'sata_write' was not declared. Should it be static?
sata_sil.c:526:5: warning: symbol 'init_sata' was not declared. Should it be static?
sata_sil.c:588:5: warning: symbol 'scan_sata' was not declared. Should it be static?
fsl_sata.c:59:6: warning: symbol 'dprint_buffer' was not declared. Should it be static?
fsl_sata.c:187:42: warning: incorrect type in assignment (different base types)
fsl_sata.c:187:42: expected unsigned int [unsigned] [usertype] cda
fsl_sata.c:187:42: got restricted __le32 [usertype] <noident>
fsl_sata.c:291:6: warning: symbol 'fsl_sata_hardware_reset' was not declared. Should it be static?
fsl_sata.c:418:27: warning: incorrect type in assignment (different base types)
fsl_sata.c:418:27: expected unsigned int [unsigned] [usertype] dba
fsl_sata.c:418:27: got restricted __le32 [usertype] <noident>
fsl_sata.c:424:41: warning: incorrect type in assignment (different base types)
fsl_sata.c:424:41: expected unsigned int [unsigned] [usertype] ext_c_ddc
fsl_sata.c:424:41: got restricted __le32 [usertype] <noident>
fsl_sata.c:431:41: warning: incorrect type in assignment (different base types)
fsl_sata.c:431:41: expected unsigned int [unsigned] [usertype] ext_c_ddc
fsl_sata.c:431:41: got restricted __le32 [usertype] <noident>
fsl_sata.c:442:22: warning: incorrect type in assignment (different base types)
fsl_sata.c:442:22: expected unsigned int [unsigned] [usertype] cda
fsl_sata.c:442:22: got restricted __le32 [usertype] <noident>
fsl_sata.c:446:31: warning: incorrect type in assignment (different base types)
fsl_sata.c:446:31: expected unsigned int [unsigned] [usertype] prde_fis_len
fsl_sata.c:446:31: got restricted __le32 [usertype] <noident>
fsl_sata.c:448:22: warning: incorrect type in assignment (different base types)
fsl_sata.c:448:22: expected unsigned int [unsigned] [usertype] ttl
fsl_sata.c:448:22: got restricted __le32 [usertype] <noident>
fsl_sata.c:460:28: warning: incorrect type in assignment (different base types)
fsl_sata.c:460:28: expected unsigned int [unsigned] [usertype] attribute
fsl_sata.c:460:28: got restricted __le32 [usertype] <noident>
fsl_sata.c:623:6: warning: symbol 'fsl_sata_flush_cache' was not declared. Should it be static?
fsl_sata.c:667:5: warning: symbol 'fsl_sata_rw_ncq_cmd' was not declared. Should it be static?
fsl_sata.c:710:6: warning: symbol 'fsl_sata_flush_cache_ext' was not declared. Should it be static?
fsl_sata.c:725:6: warning: symbol 'fsl_sata_software_reset' was not declared. Should it be static?
fsl_sata.c:760:5: warning: symbol 'ata_low_level_rw_lba48' was not declared. Should it be static?
fsl_sata.c:795:5: warning: symbol 'ata_low_level_rw_lba28' was not declared. Should it be static?
the following compiler warnings show up after fixing the above, so
remove those three functions:
fsl_sata.c:59:13: warning: 'dprint_buffer' defined but not used [-Wunused-function]
fsl_sata.c:291:13: warning: 'fsl_sata_hardware_reset' defined but not used [-Wunused-function]
fsl_sata.c:726:13: warning: 'fsl_sata_software_reset' defined but not used [-Wunused-function]
Other than that, the following are fixed by __iomem annotation:
fsl_sata.c:84:39: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:84:39: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:84:39: got unsigned int volatile *addr
fsl_sata.c:172:26: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:172:26: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:172:26: got unsigned int *<noident>
fsl_sata.c:175:19: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:175:19: expected unsigned int volatile [noderef] <asn:2>*addr
fsl_sata.c:175:19: got unsigned int *<noident>
fsl_sata.c:181:19: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:181:19: expected unsigned int volatile [noderef] <asn:2>*addr
fsl_sata.c:181:19: got unsigned int *<noident>
fsl_sata.c:184:26: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:184:26: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:184:26: got unsigned int *<noident>
fsl_sata.c:186:19: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:186:19: expected unsigned int volatile [noderef] <asn:2>*addr
fsl_sata.c:186:19: got unsigned int *<noident>
fsl_sata.c:189:26: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:189:26: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:189:26: got unsigned int *<noident>
fsl_sata.c:191:19: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:191:19: expected unsigned int volatile [noderef] <asn:2>*addr
fsl_sata.c:191:19: got unsigned int *<noident>
fsl_sata.c:194:26: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:194:26: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:194:26: got unsigned int *<noident>
fsl_sata.c:195:19: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:195:19: expected unsigned int volatile [noderef] <asn:2>*addr
fsl_sata.c:195:19: got unsigned int *<noident>
fsl_sata.c:198:19: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:198:19: expected unsigned int volatile [noderef] <asn:2>*addr
fsl_sata.c:198:19: got unsigned int *<noident>
fsl_sata.c:201:19: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:201:19: expected unsigned int volatile [noderef] <asn:2>*addr
fsl_sata.c:201:19: got unsigned int *<noident>
fsl_sata.c:204:26: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:204:26: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:204:26: got unsigned int *<noident>
fsl_sata.c:205:19: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:205:19: expected unsigned int volatile [noderef] <asn:2>*addr
fsl_sata.c:205:19: got unsigned int *<noident>
fsl_sata.c:208:26: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:208:26: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:208:26: got unsigned int *<noident>
fsl_sata.c:209:19: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:209:19: expected unsigned int volatile [noderef] <asn:2>*addr
fsl_sata.c:209:19: got unsigned int *<noident>
fsl_sata.c:212:26: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:212:26: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:212:26: got unsigned int *<noident>
fsl_sata.c:213:19: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:213:19: expected unsigned int volatile [noderef] <asn:2>*addr
fsl_sata.c:213:19: got unsigned int *<noident>
fsl_sata.c:216:19: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:216:19: expected unsigned int volatile [noderef] <asn:2>*addr
fsl_sata.c:216:19: got unsigned int *<noident>
fsl_sata.c:219:19: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:219:19: expected unsigned int volatile [noderef] <asn:2>*addr
fsl_sata.c:219:19: got unsigned int *<noident>
fsl_sata.c:222:19: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:222:19: expected unsigned int volatile [noderef] <asn:2>*addr
fsl_sata.c:222:19: got unsigned int *<noident>
fsl_sata.c:225:26: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:225:26: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:225:26: got unsigned int *<noident>
fsl_sata.c:227:19: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:227:19: expected unsigned int volatile [noderef] <asn:2>*addr
fsl_sata.c:227:19: got unsigned int *<noident>
fsl_sata.c:242:26: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:242:26: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:242:26: got unsigned int *<noident>
fsl_sata.c:256:32: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:256:32: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:256:32: got unsigned int *<noident>
fsl_sata.c:262:26: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:262:26: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:262:26: got unsigned int *<noident>
fsl_sata.c:274:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:274:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:274:53: got unsigned int *<noident>
fsl_sata.c:275:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:275:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:275:53: got unsigned int *<noident>
fsl_sata.c:276:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:276:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:276:53: got unsigned int *<noident>
fsl_sata.c:277:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:277:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:277:53: got unsigned int *<noident>
fsl_sata.c:278:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:278:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:278:53: got unsigned int *<noident>
fsl_sata.c:279:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:279:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:279:53: got unsigned int *<noident>
fsl_sata.c:280:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:280:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:280:53: got unsigned int *<noident>
fsl_sata.c:281:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:281:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:281:53: got unsigned int *<noident>
fsl_sata.c:282:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:282:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:282:53: got unsigned int *<noident>
fsl_sata.c:283:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:283:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:283:53: got unsigned int *<noident>
fsl_sata.c:284:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:284:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:284:53: got unsigned int *<noident>
fsl_sata.c:285:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:285:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:285:53: got unsigned int *<noident>
fsl_sata.c:286:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:286:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:286:53: got unsigned int *<noident>
fsl_sata.c:287:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:287:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:287:53: got unsigned int *<noident>
fsl_sata.c:288:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:288:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:288:53: got unsigned int *<noident>
fsl_sata.c:289:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:289:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:289:53: got unsigned int *<noident>
fsl_sata.c:290:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:290:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:290:53: got unsigned int *<noident>
fsl_sata.c:291:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:291:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:291:53: got unsigned int *<noident>
fsl_sata.c:292:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:292:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:292:53: got unsigned int *<noident>
fsl_sata.c:293:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:293:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:293:53: got unsigned int *<noident>
fsl_sata.c:294:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:294:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:294:53: got unsigned int *<noident>
fsl_sata.c:295:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:295:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:295:53: got unsigned int *<noident>
fsl_sata.c:296:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:296:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:296:53: got unsigned int *<noident>
fsl_sata.c:297:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:297:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:297:53: got unsigned int *<noident>
fsl_sata.c:298:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:298:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:298:53: got unsigned int *<noident>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Kim Phillips [Mon, 29 Oct 2012 13:34:39 +0000 (13:34 +0000)]
powerpc/mpc83xx: sparse fixes
fdt.c:91:78: warning: Using plain integer as NULL pointer
fdt.c:103:78: warning: Using plain integer as NULL pointer
speed.c:55:11: warning: symbol 'corecnf_tab' was not declared. Should it be static?
speed.c:519:5: warning: symbol 'do_clocks' was not declared. Should it be static?
mpc8313erdb.c:73:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:74:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:75:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:76:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:79:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:80:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:81:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:82:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:85:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:86:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:87:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:88:17: warning: obsolete struct initializer, use C99 syntax
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Kim Phillips [Mon, 29 Oct 2012 13:34:38 +0000 (13:34 +0000)]
powerpc/mpc85xx: sparse fixes
fsl_corenet_serdes.c:485:6: warning: symbol '__soc_serdes_init' was not declared. Should it be static?
cpu_init.c:185:6: warning: symbol 'invalidate_cpc' was not declared. Should it be static?
bcsr.c:28:27: warning: non-ANSI function declaration of function 'enable_8568mds_duart'
bcsr.c:39:33: warning: non-ANSI function declaration of function 'enable_8568mds_flash_write'
bcsr.c:46:34: warning: non-ANSI function declaration of function 'disable_8568mds_flash_write'
bcsr.c:53:29: warning: non-ANSI function declaration of function 'enable_8568mds_qe_mdio'
bcsr.c:28:33: warning: non-ANSI function declaration of function 'enable_8569mds_flash_write'
bcsr.c:33:34: warning: non-ANSI function declaration of function 'disable_8569mds_flash_write'
bcsr.c:38:28: warning: non-ANSI function declaration of function 'enable_8569mds_qe_uec'
bcsr.c:63:47: warning: non-ANSI function declaration of function 'disable_8569mds_brd_eeprom_write_protect'
ngpixis.c:245:1: error: directive in argument list
ngpixis.c:247:1: error: directive in argument list
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Kim Phillips [Mon, 29 Oct 2012 13:34:37 +0000 (13:34 +0000)]
arch/powerpc/cpu/mpc8xxx/: sparse fixes
ctrl_regs.c:31:5: warning: symbol 'fsl_ddr_get_version' was not declared. Should it be static?
cpu.c:135:14: warning: non-ANSI function declaration of function 'cpu_mask'
cpu.c:154:18: warning: non-ANSI function declaration of function 'cpu_numcores'
cpu.c:37:17: warning: symbol 'cpu_type_list' was not declared. Should it be static?
cpu.c:117:17: warning: symbol 'cpu_type_unknown' was not declared. Should it be static?
fsl_lbc.c:14:6: warning: symbol '__lbc_sdram_init' was not declared. Should it be static?
and:
lc_common_dimm_params.c:15:1: warning: symbol 'compute_cas_latency_ddr3' was not declared. Should it be static?
making it static produces the following compiler warning:
lc_common_dimm_params.c:15:1: warning: 'compute_cas_latency_ddr3' defined but not used [-Wunused-function]
so we protect it with the preprocessor.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Kim Phillips [Mon, 29 Oct 2012 13:34:35 +0000 (13:34 +0000)]
lib/zlib: sparse fixes
define Z_NULL to (void *)0 include/u-boot/zlib.h to get rid of most of
the NULL pointer warnings.
inflate.c:942:1: warning: non-ANSI definition of function 'inflateEnd'
inflate.c:9:1: warning: non-ANSI definition of function 'inflateReset'
inflate.c:12:17: warning: Using plain integer as NULL pointer
inflate.c:12:42: warning: Using plain integer as NULL pointer
inflate.c:15:17: warning: Using plain integer as NULL pointer
inflate.c:21:19: warning: Using plain integer as NULL pointer
inflate.c:35:1: warning: non-ANSI definition of function 'inflateInit2_'
inflate.c:38:20: warning: Using plain integer as NULL pointer
inflate.c:41:17: warning: Using plain integer as NULL pointer
inflate.c:42:17: warning: Using plain integer as NULL pointer
inflate.c:50:18: warning: Using plain integer as NULL pointer
inflate.c:65:23: warning: Using plain integer as NULL pointer
inflate.c:69:21: warning: Using plain integer as NULL pointer
inflate.c:78:1: warning: non-ANSI definition of function 'inflateInit_'
inflate.c:86:1: warning: non-ANSI definition of function 'fixedtables'
inflate.c:108:26: warning: Using plain integer as NULL pointer
inflate.c:109:1: warning: non-ANSI definition of function 'updatewindow'
inflate.c:112:30: warning: Using plain integer as NULL pointer
inflate.c:339:1: warning: non-ANSI definition of function 'inflate'
inflate.c:349:17: warning: Using plain integer as NULL pointer
inflate.c:349:42: warning: Using plain integer as NULL pointer
inflate.c:350:27: warning: Using plain integer as NULL pointer
inflate.c:369:42: warning: Using plain integer as NULL pointer
inflate.c:376:32: warning: Using plain integer as NULL pointer
inflate.c:401:54: warning: Using plain integer as NULL pointer
inflate.c:419:32: warning: Using plain integer as NULL pointer
inflate.c:426:32: warning: Using plain integer as NULL pointer
inflate.c:433:32: warning: Using plain integer as NULL pointer
inflate.c:444:36: warning: Using plain integer as NULL pointer
inflate.c:449:37: warning: Using plain integer as NULL pointer
inflate.c:450:38: warning: Using plain integer as NULL pointer
inflate.c:457:40: warning: Using plain integer as NULL pointer
inflate.c:458:47: warning: Using plain integer as NULL pointer
inflate.c:480:40: warning: Using plain integer as NULL pointer
inflate.c:481:50: warning: Using plain integer as NULL pointer
inflate.c:491:37: warning: Using plain integer as NULL pointer
inflate.c:492:37: warning: Using plain integer as NULL pointer
inflate.c:501:40: warning: Using plain integer as NULL pointer
inflate.c:502:53: warning: Using plain integer as NULL pointer
inflate.c:512:37: warning: Using plain integer as NULL pointer
inflate.c:513:40: warning: Using plain integer as NULL pointer
inflate.c:525:32: warning: Using plain integer as NULL pointer
inflate.c:529:52: warning: Using plain integer as NULL pointer
inflate.c:543:54: warning: Using plain integer as NULL pointer
inflate.c:932:17: warning: Using plain integer as NULL pointer
inflate.c:932:42: warning: Using plain integer as NULL pointer
inflate.c:935:26: warning: Using plain integer as NULL pointer
inflate.c:940:19: warning: Using plain integer as NULL pointer
adler32.c:58:5: warning: non-ANSI definition of function 'adler32'
adler32.c:81:16: warning: Using plain integer as NULL pointer
zutil.c:53:9: warning: non-ANSI definition of function 'zcalloc'
zutil.c:64:9: warning: non-ANSI definition of function 'zcfree'
inffast.c:70:1: warning: non-ANSI definition of function 'inflate_fast'
inftrees.c:33:1: warning: non-ANSI definition of function 'inflate_table'
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Kim Phillips [Mon, 29 Oct 2012 13:34:34 +0000 (13:34 +0000)]
drivers/net/: sparse fixes
phy.c:46:5: warning: symbol 'genphy_config_advert' was not declared. Should it be static?
phy.c:121:5: warning: symbol 'genphy_setup_forced' was not declared. Should it be static?
phy.c:468:5: warning: symbol 'phy_probe' was not declared. Should it be static?
phy.c:491:19: warning: symbol 'get_phy_driver' was not declared. Should it be static?
phy.c:508:19: warning: symbol 'phy_device_create' was not declared. Should it be static?
phy.c:552:5: warning: symbol 'get_phy_id' was not declared. Should it be static?
phy.c:584:19: warning: symbol 'get_phy_device' was not declared. Should it be sta
vitesse.c:126:5: warning: symbol 'vsc8601_config' was not declared. Should it be static?
vsc7385.c:33:5: warning: symbol 'vsc7385_upload_firmware' was not declared. Should it be static?
tgec_phy.c:33:5: warning: symbol 'tgec_mdio_write' was not declared. Should it be static?
tgec_phy.c:75:5: warning: symbol 'tgec_mdio_read' was not declared. Should it be static?
tgec_phy.c:117:5: warning: symbol 'tgec_mdio_reset' was not declared. Should it be static?
eth.c:48:6: warning: symbol 'dtsec_configure_serdes' was not declared. Should it be static?
p4080.c:26:5: warning: symbol 'port_to_devdisr' was not declared. Should it be static?
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Kim Phillips [Mon, 29 Oct 2012 13:34:33 +0000 (13:34 +0000)]
net/: sparse fixes
bootp.c:44:14: warning: symbol 'dhcp_state' was not declared. Should it be static?
bootp.c:45:15: warning: symbol 'dhcp_leasetime' was not declared. Should it be static?
bootp.c:46:10: warning: symbol 'NetDHCPServerIP' was not declared. Should it be static?
arp.c:30:17: warning: symbol 'NetArpWaitReplyIP' was not declared. Should it be static?
arp.c:37:16: warning: symbol 'NetArpTxPacket' was not declared. Should it be static?
arp.c:38:17: warning: symbol 'NetArpPacketBuf' was not declared. Should it be static?
atheros.c:33:19: warning: symbol 'AR8021_driver' was not declared. Should it be static?
net.c:183:7: warning: symbol 'PktBuf' was not declared. Should it be static?
net.c:159:21: warning: symbol 'net_state' was not declared. Should it be static?
ping.c:73:6: warning: symbol 'ping_start' was not declared. Should it be static?
ping.c:82:13: warning: symbol 'ping_receive' was not declared. Should it be static?
tftp.c:53:7: warning: symbol 'TftpRRQTimeoutMSecs' was not declared. Should it be static?
tftp.c:54:5: warning: symbol 'TftpRRQTimeoutCountMax' was not declared. Should it be static?
eth.c:125:19: warning: symbol 'eth_current' was not declared. Should it be static?
Note: in the ping.c fix, commit a36b12f95a29647a06b5459198684fc142482020
"net: Move PING out of net.c" mistakenly carried the ifdef CMD_PING
clause from when it was necessary to avoid warnings when it was embedded
in net.c.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
projects / u-boot.git / log
;st=author){kind=link}
