Zixun LI [Sun, 21 Jul 2024 21:45:52 +0000 (23:45 +0200)]
mtd: nand: raw: atmel: Use ONFI ECC params if available
When ECC parameters are not specified in DT, first try ONFI ECC parameters
before fallback to maximum strength.
It's the Linux driver behavior since the driver rewriting in f88fc12.
From then 2 nand system refactors have been done in 6a1b66d6 and 53576c7b,
chip->ecc_strength_ds and chip->ecc_step_ds became
nanddev_get_ecc_requirements(). U-Boot didn't follow the refactor and
always use these 2 fields.
v2: Fix formatting, add upstream commit hash.
Signed-off-by: Zixun LI <zli@ogga.fr> Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com> Acked-by: Balamanikandan Gunasundar
Tom Rini [Fri, 11 Oct 2024 18:23:25 +0000 (12:23 -0600)]
Merge patch series "Tidy up use of 'SPL' and CONFIG_SPL_BUILD"
Simon Glass <sjg@chromium.org> says:
When the SPL build-phase was first created it was designed to solve a
particular problem (the need to init SDRAM so that U-Boot proper could
be loaded). It has since expanded to become an important part of U-Boot,
with three phases now present: TPL, VPL and SPL
Due to this history, the term 'SPL' is used to mean both a particular
phase (the one before U-Boot proper) and all the non-proper phases.
This has become confusing.
For a similar reason CONFIG_SPL_BUILD is set to 'y' for all 'SPL'
phases, not just SPL. So code which can only be compiled for actual SPL,
for example, must use something like this:
In Makefiles we have similar issues. SPL_ has been used as a variable
which expands to either SPL_ or nothing, to chose between options like
CONFIG_BLK and CONFIG_SPL_BLK. When TPL appeared, a new SPL_TPL variable
was created which expanded to 'SPL_', 'TPL_' or nothing. Later it was
updated to support 'VPL_' as well.
This series starts a change in terminology and usage to resolve the
above issues:
- The word 'xPL' is used instead of 'SPL' to mean a non-proper build
- A new CONFIG_XPL_BUILD define indicates that the current build is an
'xPL' build
- The existing CONFIG_SPL_BUILD is changed to mean SPL; it is not now
defined for TPL and VPL phases
- The existing SPL_ Makefile variable is renamed to SPL_
- The existing SPL_TPL Makefile variable is renamed to PHASE_
It should be noted that xpl_phase() can generally be used instead of
the above CONFIGs without a code-space or run-time penalty.
This series does not attempt to convert all of U-Boot to use this new
terminology but it makes a start. In particular, renaming spl.h and
common/spl seems like a bridge too far at this point.
The series is fully bisectable. It has also been checked to ensure there
are no code-size changes on any commit.
Simon Glass [Mon, 30 Sep 2024 01:49:31 +0000 (19:49 -0600)]
scripts: Add some comments about autoconf.mk
Now that the conversion of all CONFIG options to Kconfig is complete,
these files only contain the xPL_BUILD defines. Add a comment to make
this clear.
Tom Rini [Thu, 10 Oct 2024 22:02:37 +0000 (16:02 -0600)]
Merge patch series "led: introduce LED boot and activity function"
Christian Marangi <ansuelsmth@gmail.com> says:
This series is a reworked version of the previous seried:
misc: introduce STATUS LED activity function
This series port and expand the legacy concept of LED boot from
the legacy Status LED API to new LED API.
One thing that many device need is a way to communicate to the
user that the device is actually doing something.
This is especially useful for recovery steps where an
user (for example) insert an USB drive, keep a button pressed
and the device autorecover.
There is currently no way to signal the user externally that
the bootloader is processing/recoverying aside from setting
a LED on.
A solid LED on is not enough and won't actually signal any
kind of progress.
Solution is the good old blinking LED but uboot doesn't
suggest (and support) interrupts and almost all the LED
are usually GPIO LED that doesn't support HW blink.
Additional Kconfg are also introduced to set the LED boot and
activity. Those are referenced by label.
A documentation for old and these new LED API is created.
Implement support for LED activity. If the feature is enabled,
make the defined ACTIVITY LED to signal mtd operations.
LED activity is implemented HERE and not in the subsystem side to limit
any performance degradation in case multiple call to MTD subsystem read/write
are done.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Implement LED activity API similar to BOOT LED API.
Usual activity might be a file transfer with TFTP, a flash write...
User of this API will call led_activity_on/off/blink() to signal these
kind of activity.
New Kconfig is implemented similar to BOOT LED, LED_ACTIVITY to
enable support for it.
It's introduced a new /options/u-boot property "activity-led" and
"activity-led-period" to define the activity LED label and the
default period when the activity LED is set to blink mode.
If "activity-led-period" is not defined, the value of 250 (ms) is
used by default.
If CONFIG_LED_BLINK or CONFIG_LED_SW_BLINK is not enabled,
led_boot_blink call will fallback to simple LED ON.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Rework BOOT LED handling. There is currently one legacy implementation
for BOOT LED from Status Led API.
This work on ancient implementation used by BOOTP by setting the LED
to Blink on boot and to turn it OFF when the firmware was correctly
received by network.
Now that we new LED implementation have support for LED boot, rework
this by also set the new BOOT LED to blink and also set it to ON before
entering main loop to confirm successful boot.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Implement LED boot API to signal correct boot of the system.
led_boot_on/off/blink() are introduced to turn ON, OFF and BLINK the
designated boot LED.
New Kconfig is introduced, CONFIG_LED_BOOT to enable the feature.
This makes use of the /options/u-boot property "boot-led" to the
define the boot LED.
It's also introduced a new /options/u-boot property "boot-led-period"
to define the default period when the LED is set to blink mode.
If "boot-led-period" is not defined, the value of 250 (ms) is
used by default.
If CONFIG_LED_BLINK or CONFIG_LED_SW_BLINK is not enabled,
led_boot_blink call will fallback to simple LED ON.
To cache the data we repurpose the now unused led_uc_priv for storage of
global LED uclass info.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
We currently init the LED OFF when SW blink is triggered when
on_state_change() is called. This can be problematic for very short
period as the ON/OFF blink might never trigger.
Toggle the LED (ON if OFF, OFF if ON) on initial SW blink to handle this
corner case and better display a LED blink from the user.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Joy Zou [Mon, 23 Sep 2024 13:11:31 +0000 (21:11 +0800)]
power: regulator: pca9450: Update the BUCK1 voltage range
The pmic could be trimed with updated BUCK1 range, so update the range
for trimed pmic. The default value of Toff_Deb is used to distinguish
the non-trimed and trimed pmic.
Signed-off-by: Joy Zou <joy.zou@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
S25HS02GT, S25HL02GT, and S28HS02GT are dual-die package parts and do
not support chip erase.
In v2, split the patch and add fixes tag.
Takahiro Kuwano (2):
mtd: spi-nor-ids: Add NO_CHIP_ERASE flag to Infineon s25hl02Gt and
s25hs02gt
mtd: spi-nor-ids: Add NO_CHIP_ERASE flag to Infineon s28hs02gt
The S25FS064S, S25FS128S, and S25FS256S are the same family of SPI NOR
Flash devices with S25FS512S. Some difference depending on the device
densities are taken care in post SFDP fixup.
Marek Vasut [Fri, 6 Sep 2024 21:09:16 +0000 (23:09 +0200)]
mtd: spi-nor-ids: Deduplicate w25q16dw entry
The w25q16dw entry exists twice in spi_nor_ids, remove the less
complete variant of the entry and keep only one copy of it.
Fixes: baef13ec9d59 ("mtd: spi-nor-ids: Add support for flashes tested by xilinx") Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Michal Simek <michal.simek@amd.com> Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Marek Vasut [Mon, 4 Mar 2024 16:16:05 +0000 (17:16 +0100)]
mtd: spi-nor: Clear Winbond SR3 WPS bit on boot
Some Winbond SPI NORs have special SR3 register which is
used among other things to control whether non-standard
"Individual Block/Sector Write Protection" (WPS bit)
locking scheme is activated. This non-standard locking
scheme is not supported by either U-Boot or Linux SPI
NOR stack so make sure it is disabled, otherwise the
SPI NOR may appear locked for no obvious reason.
This SR3 WPS appears e.g. on W25Q16FW which has the same ID as
W25Q16DW, but the W25Q16DW does not implement the SR3 WPS bit.
Tom Rini [Wed, 9 Oct 2024 22:58:42 +0000 (16:58 -0600)]
Merge tag 'efi-2025-01-rc1' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request efi-2025-01-rc1
Documentation:
* Move the generic memory-documentation to doc/
* Fix typo boormethod
UEFI:
* Delete rng-seed if having EFI RNG protocol
* Don't call restart_uboot in EFI watchdog test
* Simplify building EFI binaries in Makefile
* Show FirmwareVendor and FirmwareRevision in helloworld
* Add debug output for efi bootmeth
Other:
* CONFIG_CMD_CLK should depend on CONFIG_CLK
* simplify clk command
* enable clk command on the sandbox
test: don't call restart_uboot in EFI watchdog test
Calling u_boot_console.restart_uboot() in
test_efi_selftest_watchdog_reboot() may lead to incorrect results.
While the watchdog triggered reboot is running thee test environment may
need some time before triggering a reboot itself. This may lead to
duplicate output of the U-Boot greeter which is recorded as an error.
Reported-by: Tom Rini <trini@konsulko.com> Fixes: df172e117d1d ("test/py: test reboot by EFI watchdog") Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Simon Glass [Thu, 26 Sep 2024 21:59:31 +0000 (23:59 +0200)]
efi_loader: Rename and move CMD_BOOTEFI_HELLO_COMPILE
This is not actually a command so the name is confusing. Use
BOOTEFI_HELLO_COMPILE instead. Put it in the efi_loader directory
with the other such config options.
The link rule (for $(obj)/%_efi.so) in scripts/Makefile.lib handles
pulling in efi_crt0.o and efi_reloc.o so drop the 'extra' rules.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tom Rini [Wed, 9 Oct 2024 18:25:39 +0000 (12:25 -0600)]
Merge patch series "spi: Various Kconfig fixes"
John Watts <contact@jookia.org> says:
I'm doing some SPI work so I tried to compile all the drivers on my
sunxi board to try and avoid some regressions. This failed, so here are
some fixes for this.
This series adds support for Xilinx qspi parallel and
stacked memeories.
In parallel mode, the current implementation assumes that a maximum
of two flashes are connected. The QSPI controller splits the data
evenly between both the flashes so, both the flashes that are connected
in parallel mode should be identical.
During each operation SPI-NOR sets 0th bit for CS0 & 1st bit for CS1 in
nor->flags.
In stacked mode the current implementation assumes that a maximum of two
flashes are connected and both the flashes are of same make but can differ
in sizes. So, except the sizes all other flash parameters of both the flashes
are identical.
Spi-nor will pass on the appropriate flash select flag to low level driver,
and it will select pass all the data to that particular flash.
Write operation in parallel mode are performed in page size * 2 chunks as
each write operation results in writing both the flashes. For doubling the
address space each operation is performed at addr/2 flash offset, where addr
is the address specified by the user.
Similarly for read and erase operations it will read from both flashes, so
size and offset are divided by 2 and send to flash.
spi: zynq_qspi: Add parallel memories support in QSPI driver
Add support for parallel memories in zynq_qspi.c driver. In case of
parallel memories STRIPE bit is set and sent to the qspi ip, which will
send data bits to both the flashes in parallel. However for few commands
we should not use stripe, instead send same data to both the flashes.
Those commands are exclueded by using zynqmp_qspi_update_stripe().
spi: zynqmp_gqspi: Add parallel memories support in GQSPI driver
Add support for parallel memories in zynqmp_gqspi.c driver. In case of
parallel memories STRIPE bit is set and sent to the qspi ip, which will
send data bits to both the flashes in parallel. However for few commands
we should not use stripe, instead send same data to both the flashes.
Those commands are exclueded by using zynqmp_qspi_update_stripe().
spi: spi-uclass: Read chipselect and restrict capabilities
Read chipselect properties from DT which are populated using 'reg'
property and save it in plat->cs[] array for later use.
Also read multi chipselect capability which is used for
parallel-memories and return errors if they are passed on using DT but
driver is not capable of handling it.
mtd: spi-nor: Add parallel and stacked memories support
In parallel mode, the current implementation assumes that a maximum of
two flashes are connected. The QSPI controller splits the data evenly
between both the flashes so, both the flashes that are connected in
parallel mode should be identical.
During each operation SPI-NOR sets 0th bit for CS0 & 1st bit for CS1 in
nor->flags.
In stacked mode the current implementation assumes that a maximum of two
flashes are connected and both the flashes are of same make but can
differ in sizes. So, except the sizes all other flash parameters of both
the flashes are identical
Spi-nor will pass on the appropriate flash select flag to low level
driver, and it will select pass all the data to that particular flash.
Write operation in parallel mode are performed in page size * 2 chunks as
each write operation results in writing both the flashes. For doubling
the address space each operation is performed at addr/2 flash offset,
where addr is the address specified by the user.
Similarly for read and erase operations it will read from both flashes,
so size and offset are divided by 2 and send to flash.
Adding the config option SPI_ADVANCE for non SPL code.
Daniel Palmer [Sun, 29 Sep 2024 09:27:39 +0000 (18:27 +0900)]
cmd: Make bootvx independent of bootelf
There are lots of usecases for running baremetal ELF
binaries via bootelf but if you enable bootelf you
get bootvx as well and you probably don't want or need
it.
mkimage: ecdsa: add signature/key nodes to dtb if missing
If the signature/key node(s) are not yet present in the U-Boot device
tree, ecdsa_add_verify_data simply fails if it can't find the nodes.
This behaviour differs from rsa_add_verify_data, wich does add the missing
nodes and proceeds in that case.
This change is mainly copy&paste from rsa_add_verify_data to add the
same behaviour to ecdsa_add_verify_data.
projects / u-boot.git / log
