From: Philippe Schenker <philippe.schenker@toradex.com>
Date: Fri, 8 Apr 2022 08:07:11 +0000 (+0200)
Subject: board: colibri-imx6ull: fix detecting ethernet phy
X-Git-Url: http://git.dujemihanovic.xyz/img/static/git-favicon.png?a=commitdiff_plain;h=aa6f57d87767089a8685ada55ca99e67c90a86d9;p=u-boot.git

board: colibri-imx6ull: fix detecting ethernet phy

Now that it is possible to use regulator-fixed-clock make use
of it. This makes U-Boot detect the PHY on first cold-boot.

This commit also adjusts the code in setup_fec and follows
how it is done in mx6ullevk.c

This commit also slows down the boot-process by about 150ms
as it now waits for the regulator-fixed-clock voltage that
drives the PHY to go up.
If you rely on very fast boot-speeds and don't need ethernet
for your boot-process you can safely revert the changes on
imx6ull-colibri.dtsi

Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
---

diff --git a/arch/arm/dts/imx6ull-colibri.dtsi b/arch/arm/dts/imx6ull-colibri.dtsi
index 56ee2895ae..88d5e15b8c 100644
--- a/arch/arm/dts/imx6ull-colibri.dtsi
+++ b/arch/arm/dts/imx6ull-colibri.dtsi
@@ -64,6 +64,18 @@
 		gpio = <&gpio1 2 GPIO_ACTIVE_LOW>; /* USBH_PEN */
 		vin-supply = <&reg_5v0>;
 	};
+
+	reg_eth_phy: regulator-eth-phy {
+		compatible = "regulator-fixed-clock";
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "eth_phy";
+		regulator-type = "voltage";
+		vin-supply = <&reg_module_3v3>;
+		clocks = <&clks IMX6UL_CLK_ENET2_REF_125M>;
+		startup-delay-us = <150000>;
+	};
 };
 
 &adc1 {
@@ -84,6 +96,7 @@
 	pinctrl-0 = <&pinctrl_enet2>;
 	phy-mode = "rmii";
 	phy-handle = <&ethphy1>;
+	phy-supply = <&reg_eth_phy>;
 	status = "okay";
 
 	mdio {
diff --git a/board/toradex/colibri-imx6ull/colibri-imx6ull.c b/board/toradex/colibri-imx6ull/colibri-imx6ull.c
index 3244184f27..ba4e0df2c2 100644
--- a/board/toradex/colibri-imx6ull/colibri-imx6ull.c
+++ b/board/toradex/colibri-imx6ull/colibri-imx6ull.c
@@ -100,28 +100,21 @@ static int setup_fec(void)
 	struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
 	int ret;
 
-	/* provide the PHY clock from the i.MX 6 */
+	/*
+	 * Use 50MHz anatop loopback REF_CLK2 for ENET2,
+	 * clear gpr1[14], set gpr1[18].
+	 */
+	clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC2_MASK,
+			IOMUX_GPR1_FEC2_CLOCK_MUX1_SEL_MASK);
+
 	ret = enable_fec_anatop_clock(1, ENET_50MHZ);
 	if (ret)
 		return ret;
 
-	/* Use 50M anatop REF_CLK and output it on ENET2_TX_CLK */
-	clrsetbits_le32(&iomuxc_regs->gpr[1],
-			IOMUX_GPR1_FEC2_CLOCK_MUX2_SEL_MASK,
-			IOMUX_GPR1_FEC2_CLOCK_MUX1_SEL_MASK);
-
-	/* give new Ethernet PHY power save mode circuitry time to settle */
-	mdelay(300);
+	enable_enet_clk(1);
 
 	return 0;
 }
-
-int board_phy_config(struct phy_device *phydev)
-{
-	if (phydev->drv->config)
-		phydev->drv->config(phydev);
-	return 0;
-}
 #endif /* CONFIG_FEC_MXC */
 
 int board_init(void)