From: Chintan Vankar Date: Thu, 26 Sep 2024 05:01:38 +0000 (+0530) Subject: doc: board: ti: am62x_sk: Add document for Ethernet boot on AM62x SoC. X-Git-Url: http://git.dujemihanovic.xyz/img/static/git-favicon.png?a=commitdiff_plain;h=4b5750aaeeb007bd822c77fee77dc3c51597e5d2;p=u-boot.git doc: board: ti: am62x_sk: Add document for Ethernet boot on AM62x SoC. Document the procedure to enable Ethernet Boot on AM62x SoC. Signed-off-by: Chintan Vankar --- diff --git a/doc/board/ti/am62x_sk.rst b/doc/board/ti/am62x_sk.rst index 51dab839dd..dab2970a85 100644 --- a/doc/board/ti/am62x_sk.rst +++ b/doc/board/ti/am62x_sk.rst @@ -305,6 +305,10 @@ https://www.ti.com/lit/pdf/spruiv7 under the `Boot Mode Pins` section. - 00000000 - 11001010 + * - Ethernet + - 00110000 + - 11000100 + For SW2 and SW1, the switch state in the "ON" position = 1. DFU based boot @@ -330,6 +334,198 @@ When using dfu-util the following commands can be used to boot to a U-Boot shell .. am62x_evm_rst_include_end_dfu_boot +Ethernet based boot +------------------- + +To boot the board via Ethernet, configure the BOOT MODE pins for Ethernet boot. + +On powering on the device, ROM uses the Ethernet Port corresponding to CPSW3G's MAC +Port 1 to transmit "TI K3 Bootp Boot". + +The TFTP server and DHCP server on the receiver device need to be configured such +that VCI string "TI K3 Bootp Boot" maps to the file `tiboot3.bin` and the TFTP +server should be capable of transferring it to the device. + +**Configuring DHCP server includes following steps:** + +* Install DHCP server: + +.. prompt:: bash $ + + sudo apt install isc-dhcp-server + +* Disable services before configuring: + +.. prompt:: bash $ + + sudo systemctl disable --now isc-dhcp-server.service isc-dhcp-server6.service + +* DHCP server setup + +Run the ip link or ifconfig command to find the name of your network interface: + +Example + +.. code-block:: + + eno1: flags=4163 mtu 1500 + inet 172.24.145.229 netmask 255.255.254.0 broadcast 172.24.145.255 + inet6 fe80::bbd5:34c8:3d4c:5de4 prefixlen 64 scopeid 0x20 + ether c0:18:03:bd:b1:a6 txqueuelen 1000 (Ethernet) + RX packets 2733979 bytes 1904440459 (1.9 GB) + RX errors 0 dropped 3850 overruns 0 frame 0 + TX packets 796807 bytes 84534764 (84.5 MB) + TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 + device interrupt 16 memory 0xe2200000-e2220000 + + enxf8e43b8cffe8: flags=4163 mtu 1500 + ether f8:e4:3b:8c:ff:e8 txqueuelen 1000 (Ethernet) + RX packets 95 bytes 31160 (31.1 KB) + RX errors 0 dropped 0 overruns 0 frame 0 + TX packets 89 bytes 17445 (17.4 KB) + TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 + + lo: flags=73 mtu 65536 + inet 127.0.0.1 netmask 255.0.0.0 + inet6 ::1 prefixlen 128 scopeid 0x10 + loop txqueuelen 1000 (Local Loopback) + RX packets 85238 bytes 7244462 (7.2 MB) + RX errors 0 dropped 0 overruns 0 frame 0 + TX packets 85238 bytes 7244462 (7.2 MB) + TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 + +Suppose we are using enxf8e43b8cffe8 interface, one end of it is connected to host PC +and other to board. + +* Do the following changes in /etc/dhcp/dhcpd.conf in host PC. + +.. code-block:: + + subnet 192.168.0.0 netmask 255.255.254.0 + { + range dynamic-bootp 192.168.0.2 192.168.0.5; + if substring (option vendor-class-identifier, 0, 16) = "TI K3 Bootp Boot" + { + filename "tiboot3.bin"; + } elsif substring (option vendor-class-identifier, 0, 20) = "AM62X U-Boot R5 SPL" + { + filename "tispl.bin"; + } elsif substring (option vendor-class-identifier, 0, 21) = "AM62X U-Boot A53 SPL" + { + filename "u-boot.img"; + } + default-lease-time 60000; + max-lease-time 720000; + next-server 192.168.0.1; + } + +* Do following changes in /etc/default/isc-dhcp-server + +.. code-block:: + + DHCPDv4_CONF=/etc/dhcp/dhcpd.conf + INTERFACESv4="enxf8e43b8cffe8" + INTERFACESv6="" + +* For your interface change ip address and netmask to next-server and your netmask + +.. prompt:: bash $ + + sudo ifconfig enxf8e43b8cffe8 192.168.0.1 netmask 255.255.254.0 + +* Enable DHCP + +.. prompt:: bash $ + + sudo systemctl enable --now isc-dhcp-server + +* To see if there is any configuration error or if dhcp is running run + +.. prompt:: bash $ + + sudo service isc-dhcp-server status + # If it shows error then something is wrong with configuration + +**For TFTP setup follow below steps:** + +* Install TFTP server: + +.. prompt:: bash $ + + sudo apt install tftpd-hpa + +tftpd-hpa package should be installed. + +Now, check whether the tftpd-hpa service is running with the following command: + +.. prompt:: bash $ + + sudo systemctl status tftpd-hpa + +* Configuring TFTP server: + +The default configuration file of tftpd-hpa server is /etc/default/tftpd-hpa. +If you want to configure the TFTP server, then you have to modify this configuration +file and restart the tftpd-hpa service afterword. + +To modify the /etc/default/tftpd-hpa configuration file, run the following command + +.. prompt:: bash $ + + sudo vim /etc/default/tftpd-hpa + +Configuration file may contain following configuration options by default: + +.. code-block:: + + # /etc/default/tftpd-hpa + + TFTP_USERNAME="tftp" + TFTP_DIRECTORY="/var/lib/tftpboot" + TFTP_ADDRESS=":69" + TFTP_OPTIONS="--secure" + +Now change the **TFTP_DIRECTORY** to **/tftp** and add the **--create** option to the +**TFTP_OPTIONS**. Without the **--create** option, you won't be able to create or upload +new files to the TFTP server. You will only be able to update existing files. + +After above changes /etc/default/tftpd-hpa file would look like this: + +.. code-block:: + + # /etc/default/tftpd-hpa + + TFTP_USERNAME="tftp" + TFTP_DIRECTORY="/tftp" + TFTP_ADDRESS=":69" + TFTP_OPTIONS="--secure --create" + +Since we have configured tftp directory as /tftp, put tiboot3.bin, tispl.bin +and u-boot.img after building it using sdk or manually cloning all the repos. + +To build binaries use following defconfig files: + +.. code-block:: + + am62x_evm_r5_ethboot_defconfig + am62x_evm_a53_ethboot_defconfig + +`tiboot3.bin` is expected to be built from `am62x_evm_r5_ethboot_defconfig` and +`tispl.bin` and `u-boot.img` are expected to be built from +`am62x_evm_a53_ethboot_defconfig`. + +Images should get fetched in following sequence as a part of boot procedure: + +.. code-block:: + + tiboot3.bin => tispl.bin => u-boot.img + +ROM loads and executes `tiboot3.bin` provided by the TFTP server. + +Next, based on NET_VCI_STRING string mentioned in respective defconfig file `tiboot3.bin` +fetches `tispl.bin` and then `tispl.bin` fetches `u-boot.img` from TFTP server which +completes Ethernet boot on the device. + Debugging U-Boot ----------------