arm: dts: am642-sk: Add initial sk dts

AM642 StarterKit (SK) board is a low cost, small form factor board
designed for TI’s AM642 SoC. It supports the following interfaces:
* 2 GB LPDDR4 RAM
* x2 Gigabit Ethernet interfaces capable of working in switch and MAC mode
* x1 USB 3.0 Type-A port
* x1 UHS-1 capable µSD card slot
* 2.4/5 GHz WLAN + Bluetooth 4.2 through WL1837
* 512 Mbit OSPI flash
* x2 UART through UART-USB bridge
* XDS110 for onboard JTAG debug using USB
* Temperature sensors, user push buttons and LEDs
* 40-pin Raspberry Pi compatible GPIO header
* 24-pin header for peripherals in MCU island (I2C, UART, SPI, IO)
* 54-pin header for Programmable Realtime Unit (PRU) IO pins
* Interface for remote automation. Includes:
	* power measurement and reset control
	* boot mode change

Add basic support for AM642 SK.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index a61f34aebac7bad30f06a774cf51edb76284ac42..aadda1991b06a2579f11c361a78b9d98ef54e7c7 100644 (file)
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -1057,7 +1057,8 @@ dtb-$(CONFIG_SOC_K3_J721E) += k3-j721e-common-proc-board.dtb \
                              k3-j7200-common-proc-board.dtb \
                              k3-j7200-r5-common-proc-board.dtb
 dtb-$(CONFIG_SOC_K3_AM642) += k3-am642-evm.dtb \
-                             k3-am642-r5-evm.dtb
+                             k3-am642-r5-evm.dtb \
+                             k3-am642-sk.dtb
 
 dtb-$(CONFIG_ARCH_MEDIATEK) += \
        mt7622-rfb.dtb \

diff --git a/arch/arm/dts/k3-am642-sk-u-boot.dtsi b/arch/arm/dts/k3-am642-sk-u-boot.dtsi
new file mode 100644 (file)
index 0000000..9e170e5
--- /dev/null
+++ b/arch/arm/dts/k3-am642-sk-u-boot.dtsi
@@ -0,0 +1,87 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/ {
+       chosen {
+               stdout-path = "serial2:115200n8";
+               tick-timer = &timer1;
+       };
+};
+
+&cbass_main{
+       u-boot,dm-spl;
+       timer1: timer@2400000 {
+               compatible = "ti,omap5430-timer";
+               reg = <0x0 0x2400000 0x0 0x80>;
+               ti,timer-alwon;
+               clock-frequency = <250000000>;
+               u-boot,dm-spl;
+       };
+};
+
+&main_conf {
+       u-boot,dm-spl;
+       chipid@14 {
+               u-boot,dm-spl;
+       };
+};
+
+&main_pmx0 {
+       u-boot,dm-spl;
+       main_i2c0_pins_default: main-i2c0-pins-default {
+               u-boot,dm-spl;
+               pinctrl-single,pins = <
+                       AM64X_IOPAD(0x0260, PIN_INPUT_PULLUP, 0) /* (A18) I2C0_SCL */
+                       AM64X_IOPAD(0x0264, PIN_INPUT_PULLUP, 0) /* (B18) I2C0_SDA */
+               >;
+       };
+};
+
+&main_i2c0 {
+       u-boot,dm-spl;
+       pinctrl-names = "default";
+       pinctrl-0 = <&main_i2c0_pins_default>;
+       clock-frequency = <400000>;
+};
+
+&main_uart0 {
+       u-boot,dm-spl;
+};
+
+&dmss {
+       u-boot,dm-spl;
+};
+
+&secure_proxy_main {
+       u-boot,dm-spl;
+};
+
+&dmsc {
+       u-boot,dm-spl;
+};
+
+&k3_pds {
+       u-boot,dm-spl;
+};
+
+&k3_clks {
+       u-boot,dm-spl;
+};
+
+&k3_reset {
+       u-boot,dm-spl;
+};
+
+&sdhci0 {
+       u-boot,dm-spl;
+};
+
+&sdhci1 {
+       u-boot,dm-spl;
+};
+
+&main_mmc1_pins_default {
+       u-boot,dm-spl;
+};

diff --git a/arch/arm/dts/k3-am642-sk.dts b/arch/arm/dts/k3-am642-sk.dts
new file mode 100644 (file)
index 0000000..d557c49
--- /dev/null
+++ b/arch/arm/dts/k3-am642-sk.dts
@@ -0,0 +1,94 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include "k3-am642.dtsi"
+
+/ {
+       compatible =  "ti,am642-sk", "ti,am642";
+       model = "Texas Instruments AM642 SK";
+
+       chosen {
+               stdout-path = "serial2:115200n8";
+               bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
+       };
+
+       memory@80000000 {
+               device_type = "memory";
+               /* 2G RAM */
+               reg = <0x00000000 0x80000000 0x00000000 0x80000000>;
+
+       };
+
+       reserved-memory {
+               #address-cells = <2>;
+               #size-cells = <2>;
+               ranges;
+
+               secure_ddr: optee@9e800000 {
+                       reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */
+                       alignment = <0x1000>;
+                       no-map;
+               };
+       };
+};
+
+&main_pmx0 {
+       main_mmc1_pins_default: main-mmc1-pins-default {
+               pinctrl-single,pins = <
+                       AM64X_IOPAD(0x0294, PIN_INPUT, 0) /* (J19) MMC1_CMD */
+                       AM64X_IOPAD(0x0290, PIN_INPUT, 0) /* (#N/A) MMC1_CLKLB */
+                       AM64X_IOPAD(0x028c, PIN_INPUT, 0) /* (L20) MMC1_CLK */
+                       AM64X_IOPAD(0x0288, PIN_INPUT, 0) /* (K21) MMC1_DAT0 */
+                       AM64X_IOPAD(0x0284, PIN_INPUT, 0) /* (L21) MMC1_DAT1 */
+                       AM64X_IOPAD(0x0280, PIN_INPUT, 0) /* (K19) MMC1_DAT2 */
+                       AM64X_IOPAD(0x027c, PIN_INPUT, 0) /* (K18) MMC1_DAT3 */
+                       AM64X_IOPAD(0x0298, PIN_INPUT, 0) /* (D19) MMC1_SDCD */
+               >;
+       };
+
+       main_i2c1_pins_default: main-i2c1-pins-default {
+               pinctrl-single,pins = <
+                       AM64X_IOPAD(0x0268, PIN_INPUT_PULLUP, 0) /* (C18) I2C1_SCL */
+                       AM64X_IOPAD(0x026c, PIN_INPUT_PULLUP, 0) /* (B19) I2C1_SDA */
+               >;
+       };
+};
+
+&main_uart1 {
+       /* main_uart1 is reserved for firmware usage */
+       status = "reserved";
+};
+
+&main_uart2 {
+       status = "disabled";
+};
+
+&main_uart3 {
+       status = "disabled";
+};
+
+&main_uart4 {
+       status = "disabled";
+};
+
+&main_uart5 {
+       status = "disabled";
+};
+
+&main_uart6 {
+       status = "disabled";
+};
+
+&sdhci1 {
+       /* SD/MMC */
+       pinctrl-names = "default";
+       bus-width = <4>;
+       pinctrl-0 = <&main_mmc1_pins_default>;
+       ti,driver-strength-ohm = <50>;
+       disable-wp;
+};