net: mediatek: connect switch to PSE only when starting eth is requested

So far the switch is initialized in probe stage and is connected to PSE
unconditionally. This will cause all packets being flooded to PSE and may
cause PSE hang before entering linux.

This patch changes the connection between switch and PSE:
- Still initialize switch in probe stage, but disconnect it with PSE
- Connect switch with PSE on eth start
- Disconnect on eth stop

Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>

diff --git a/drivers/net/mtk_eth.c b/drivers/net/mtk_eth.c
index 4c9fb266c7aeb4f3c9f6fe5fe340ddeadaf3278d..90f1d2591b6eb030684e8ec9511a976dabb82b6d 100644 (file)
--- a/drivers/net/mtk_eth.c
+++ b/drivers/net/mtk_eth.c
@@ -123,8 +123,10 @@ struct mtk_eth_priv {
 
        enum mtk_switch sw;
        int (*switch_init)(struct mtk_eth_priv *priv);
+       void (*switch_mac_control)(struct mtk_eth_priv *priv, bool enable);
        u32 mt753x_smi_addr;
        u32 mt753x_phy_base;
+       u32 mt753x_pmcr;
 
        struct gpio_desc rst_gpio;
        int mcm;
@@ -613,6 +615,16 @@ static int mt7530_pad_clk_setup(struct mtk_eth_priv *priv, int mode)
        return 0;
 }
 
+static void mt7530_mac_control(struct mtk_eth_priv *priv, bool enable)
+{
+       u32 pmcr = FORCE_MODE;
+
+       if (enable)
+               pmcr = priv->mt753x_pmcr;
+
+       mt753x_reg_write(priv, PMCR_REG(6), pmcr);
+}
+
 static int mt7530_setup(struct mtk_eth_priv *priv)
 {
        u16 phy_addr, phy_val;
@@ -663,11 +675,14 @@ static int mt7530_setup(struct mtk_eth_priv *priv)
              FORCE_DPX | FORCE_LINK;
 
        /* MT7530 Port6: Forced 1000M/FD, FC disabled */
-       mt753x_reg_write(priv, PMCR_REG(6), val);
+       priv->mt753x_pmcr = val;
 
        /* MT7530 Port5: Forced link down */
        mt753x_reg_write(priv, PMCR_REG(5), FORCE_MODE);
 
+       /* Keep MAC link down before starting eth */
+       mt753x_reg_write(priv, PMCR_REG(6), FORCE_MODE);
+
        /* MT7530 Port6: Set to RGMII */
        mt753x_reg_rmw(priv, MT7530_P6ECR, P6_INTF_MODE_M, P6_INTF_MODE_RGMII);
 
@@ -823,6 +838,17 @@ static void mt7531_phy_setting(struct mtk_eth_priv *priv)
        }
 }
 
+static void mt7531_mac_control(struct mtk_eth_priv *priv, bool enable)
+{
+       u32 pmcr = FORCE_MODE_LNK;
+
+       if (enable)
+               pmcr = priv->mt753x_pmcr;
+
+       mt753x_reg_write(priv, PMCR_REG(5), pmcr);
+       mt753x_reg_write(priv, PMCR_REG(6), pmcr);
+}
+
 static int mt7531_setup(struct mtk_eth_priv *priv)
 {
        u16 phy_addr, phy_val;
@@ -882,8 +908,11 @@ static int mt7531_setup(struct mtk_eth_priv *priv)
               (SPEED_1000M << FORCE_SPD_S) | FORCE_DPX |
               FORCE_LINK;
 
-       mt753x_reg_write(priv, PMCR_REG(5), pmcr);
-       mt753x_reg_write(priv, PMCR_REG(6), pmcr);
+       priv->mt753x_pmcr = pmcr;
+
+       /* Keep MAC link down before starting eth */
+       mt753x_reg_write(priv, PMCR_REG(5), FORCE_MODE_LNK);
+       mt753x_reg_write(priv, PMCR_REG(6), FORCE_MODE_LNK);
 
        /* Turn on PHYs */
        for (i = 0; i < MT753X_NUM_PHYS; i++) {
@@ -1227,6 +1256,9 @@ static int mtk_eth_start(struct udevice *dev)
 
        mtk_eth_fifo_init(priv);
 
+       if (priv->switch_mac_control)
+               priv->switch_mac_control(priv, true);
+
        /* Start PHY */
        if (priv->sw == SW_NONE) {
                ret = mtk_phy_start(priv);
@@ -1245,6 +1277,9 @@ static void mtk_eth_stop(struct udevice *dev)
 {
        struct mtk_eth_priv *priv = dev_get_priv(dev);
 
+       if (priv->switch_mac_control)
+               priv->switch_mac_control(priv, false);
+
        mtk_pdma_rmw(priv, PDMA_GLO_CFG_REG,
                     TX_WB_DDONE | RX_DMA_EN | TX_DMA_EN, 0);
        udelay(500);
@@ -1484,16 +1519,19 @@ static int mtk_eth_of_to_plat(struct udevice *dev)
        /* check for switch first, otherwise phy will be used */
        priv->sw = SW_NONE;
        priv->switch_init = NULL;
+       priv->switch_mac_control = NULL;
        str = dev_read_string(dev, "mediatek,switch");
 
        if (str) {
                if (!strcmp(str, "mt7530")) {
                        priv->sw = SW_MT7530;
                        priv->switch_init = mt7530_setup;
+                       priv->switch_mac_control = mt7530_mac_control;
                        priv->mt753x_smi_addr = MT753X_DFL_SMI_ADDR;
                } else if (!strcmp(str, "mt7531")) {
                        priv->sw = SW_MT7531;
                        priv->switch_init = mt7531_setup;
+                       priv->switch_mac_control = mt7531_mac_control;
                        priv->mt753x_smi_addr = MT753X_DFL_SMI_ADDR;
                } else {
                        printf("error: unsupported switch\n");