The latest PPC4xx register cleanup patch missed some SDRAM defines.
This patch now changes lower case UIC defines to upper case. Also
some names are changed to match the naming in the IBM/AMCC users
manuals (e.g. mem_mcopt1 -> SDRAM0_CFG).
Signed-off-by: Stefan Roese <sr@denx.de>
/*--------------------------------------------------------------------
* Setup some default
*------------------------------------------------------------------*/
- mtsdram(mem_uabba, 0x00000000); /* ubba=0 (default) */
- mtsdram(mem_slio, 0x00000000); /* rdre=0 wrre=0 rarw=0 */
- mtsdram(mem_devopt, 0x00000000); /* dll=0 ds=0 (normal) */
- mtsdram(mem_wddctr, 0x00000000); /* wrcp=0 dcd=0 */
- mtsdram(mem_clktr, 0x40000000); /* clkp=1 (90 deg wr) dcdt=0 */
+ mtsdram(SDRAM0_UABBA, 0x00000000); /* ubba=0 (default) */
+ mtsdram(SDRAM0_SLIO, 0x00000000); /* rdre=0 wrre=0 rarw=0 */
+ mtsdram(SDRAM0_DEVOPT, 0x00000000); /* dll=0 ds=0 (normal) */
+ mtsdram(SDRAM0_WDDCTR, 0x00000000); /* wrcp=0 dcd=0 */
+ mtsdram(SDRAM0_CLKTR, 0x40000000); /* clkp=1 (90 deg wr) dcdt=0 */
/*--------------------------------------------------------------------
* Setup for board-specific specific mem
/*
* Following for CAS Latency = 2.5 @ 133 MHz PLB
*/
- mtsdram(mem_b0cr, 0x000a4001); /* SDBA=0x000 128MB, Mode 3, enabled */
- mtsdram(mem_tr0, 0x410a4012); /* WR=2 WD=1 CL=2.5 PA=3 CP=4 LD=2 */
+ mtsdram(SDRAM0_B0CR, 0x000a4001); /* SDBA=0x000 128MB, Mode 3, enabled */
+ mtsdram(SDRAM0_TR0, 0x410a4012); /* WR=2 WD=1 CL=2.5 PA=3 CP=4 LD=2 */
/* RA=10 RD=3 */
- mtsdram(mem_tr1, 0x8080082f); /* SS=T2 SL=STAGE 3 CD=1 CT=0x02f */
- mtsdram(mem_rtr, 0x08200000); /* Rate 15.625 ns @ 133 MHz PLB */
- mtsdram(mem_cfg1, 0x00000000); /* Self-refresh exit, disable PM */
+ mtsdram(SDRAM0_TR1, 0x8080082f); /* SS=T2 SL=STAGE 3 CD=1 CT=0x02f */
+ mtsdram(SDRAM0_RTR, 0x08200000); /* Rate 15.625 ns @ 133 MHz PLB */
+ mtsdram(SDRAM0_CFG1, 0x00000000); /* Self-refresh exit, disable PM */
udelay(400); /* Delay 200 usecs (min) */
/*--------------------------------------------------------------------
* Enable the controller, then wait for DCEN to complete
*------------------------------------------------------------------*/
- mtsdram(mem_cfg0, 0x86000000); /* DCEN=1, PMUD=1, 64-bit */
+ mtsdram(SDRAM0_CFG0, 0x86000000); /* DCEN=1, PMUD=1, 64-bit */
for (;;) {
- mfsdram(mem_mcsts, reg);
+ mfsdram(SDRAM0_MCSTS, reg);
if (reg & 0x80000000)
break;
}
/*--------------------------------------------------------------------
* Setup some default
*------------------------------------------------------------------*/
- mtsdram (mem_uabba, 0x00000000); /* ubba=0 (default) */
- mtsdram (mem_slio, 0x00000000); /* rdre=0 wrre=0 rarw=0 */
- mtsdram (mem_devopt, 0x00000000); /* dll=0 ds=0 (normal) */
- mtsdram (mem_wddctr, 0x00000000); /* wrcp=0 dcd=0 */
- mtsdram (mem_clktr, 0x40000000); /* clkp=1 (90 deg wr) dcdt=0 */
+ mtsdram (SDRAM0_UABBA, 0x00000000); /* ubba=0 (default) */
+ mtsdram (SDRAM0_SLIO, 0x00000000); /* rdre=0 wrre=0 rarw=0 */
+ mtsdram (SDRAM0_DEVOPT, 0x00000000); /* dll=0 ds=0 (normal) */
+ mtsdram (SDRAM0_WDDCTR, 0x00000000); /* wrcp=0 dcd=0 */
+ mtsdram (SDRAM0_CLKTR, 0x40000000); /* clkp=1 (90 deg wr) dcdt=0 */
/*--------------------------------------------------------------------
* Setup for board-specific specific mem
/*
* Following for CAS Latency = 2.5 @ 133 MHz PLB
*/
- mtsdram (mem_b0cr, 0x000a4001); /* SDBA=0x000 128MB, Mode 3, enabled */
- mtsdram (mem_tr0, 0x410a4012); /* WR=2 WD=1 CL=2.5 PA=3 CP=4 LD=2 */
+ mtsdram (SDRAM0_B0CR, 0x000a4001); /* SDBA=0x000 128MB, Mode 3, enabled */
+ mtsdram (SDRAM0_TR0, 0x410a4012); /* WR=2 WD=1 CL=2.5 PA=3 CP=4 LD=2 */
/* RA=10 RD=3 */
- mtsdram (mem_tr1, 0x8080082f); /* SS=T2 SL=STAGE 3 CD=1 CT=0x02f */
- mtsdram (mem_rtr, 0x08200000); /* Rate 15.625 ns @ 133 MHz PLB */
- mtsdram (mem_cfg1, 0x00000000); /* Self-refresh exit, disable PM */
+ mtsdram (SDRAM0_TR1, 0x8080082f); /* SS=T2 SL=STAGE 3 CD=1 CT=0x02f */
+ mtsdram (SDRAM0_RTR, 0x08200000); /* Rate 15.625 ns @ 133 MHz PLB */
+ mtsdram (SDRAM0_CFG1, 0x00000000); /* Self-refresh exit, disable PM */
udelay (400); /* Delay 200 usecs (min) */
/*--------------------------------------------------------------------
* Enable the controller, then wait for DCEN to complete
*------------------------------------------------------------------*/
- mtsdram (mem_cfg0, 0x86000000); /* DCEN=1, PMUD=1, 64-bit */
+ mtsdram (SDRAM0_CFG0, 0x86000000); /* DCEN=1, PMUD=1, 64-bit */
for (;;) {
- mfsdram (mem_mcsts, reg);
+ mfsdram (SDRAM0_MCSTS, reg);
if (reg & 0x80000000)
break;
}
/* go through all possible SDRAM0_TR1[RDCT] values */
for (i=0; i<=0x1ff; i++) {
/* set the current value for TR1 */
- mtsdram(mem_tr1, (0x80800800 | i));
+ mtsdram(SDRAM0_TR1, (0x80800800 | i));
/* write values */
for (j=0; j<NUM_TRIES; j++) {
/*--------------------------------------------------------------------
* Setup some default
*------------------------------------------------------------------*/
- mtsdram(mem_uabba, 0x00000000); /* ubba=0 (default) */
- mtsdram(mem_slio, 0x00000000); /* rdre=0 wrre=0 rarw=0 */
- mtsdram(mem_devopt, 0x00000000); /* dll=0 ds=0 (normal) */
- mtsdram(mem_clktr, 0x40000000); /* ?? */
- mtsdram(mem_wddctr, 0x40000000); /* ?? */
+ mtsdram(SDRAM0_UABBA, 0x00000000); /* ubba=0 (default) */
+ mtsdram(SDRAM0_SLIO, 0x00000000); /* rdre=0 wrre=0 rarw=0 */
+ mtsdram(SDRAM0_DEVOPT, 0x00000000); /* dll=0 ds=0 (normal) */
+ mtsdram(SDRAM0_CLKTR, 0x40000000); /* ?? */
+ mtsdram(SDRAM0_WDDCTR, 0x40000000); /* ?? */
/*clear this first, if the DDR is enabled by a debugger
then you can not make changes. */
- mtsdram(mem_cfg0, 0x00000000); /* Disable EEC */
+ mtsdram(SDRAM0_CFG0, 0x00000000); /* Disable EEC */
/*--------------------------------------------------------------------
* Setup for board-specific specific mem
/*
* Following for CAS Latency = 2.5 @ 133 MHz PLB
*/
- mtsdram(mem_b0cr, 0x000a4001); /* SDBA=0x000 128MB, Mode 3, enabled */
- mtsdram(mem_b1cr, 0x080a4001); /* SDBA=0x080 128MB, Mode 3, enabled */
+ mtsdram(SDRAM0_B0CR, 0x000a4001); /* SDBA=0x000 128MB, Mode 3, enabled */
+ mtsdram(SDRAM0_B1CR, 0x080a4001); /* SDBA=0x080 128MB, Mode 3, enabled */
- mtsdram(mem_tr0, 0x410a4012); /* ?? */
- mtsdram(mem_rtr, 0x04080000); /* ?? */
- mtsdram(mem_cfg1, 0x00000000); /* Self-refresh exit, disable PM */
- mtsdram(mem_cfg0, 0x30000000); /* Disable EEC */
+ mtsdram(SDRAM0_TR0, 0x410a4012); /* ?? */
+ mtsdram(SDRAM0_RTR, 0x04080000); /* ?? */
+ mtsdram(SDRAM0_CFG1, 0x00000000); /* Self-refresh exit, disable PM */
+ mtsdram(SDRAM0_CFG0, 0x30000000); /* Disable EEC */
udelay(400); /* Delay 200 usecs (min) */
/*--------------------------------------------------------------------
* Enable the controller, then wait for DCEN to complete
*------------------------------------------------------------------*/
- mtsdram(mem_cfg0, 0x80000000); /* Enable */
+ mtsdram(SDRAM0_CFG0, 0x80000000); /* Enable */
for (;;) {
- mfsdram(mem_mcsts, reg);
+ mfsdram(SDRAM0_MCSTS, reg);
if (reg & 0x80000000)
break;
}
sdram_tr1_set(0x00000000, &tr1_bank1);
sdram_tr1_set(0x08000000, &tr1_bank2);
- mtsdram(mem_tr1, (((tr1_bank1+tr1_bank2)/2) | 0x80800800));
+ mtsdram(SDRAM0_TR1, (((tr1_bank1+tr1_bank2)/2) | 0x80800800));
return CONFIG_SYS_SDRAM_BANKS * (CONFIG_SYS_KBYTES_SDRAM * 1024); /* return bytes */
}
unsigned long tmp;
/* write SDRAM bank 0 register */
- mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B0CR);
mtdcr (SDRAM0_CFGDATA, 0x00062001);
/* Set the SDRAM Timing reg, SDTR1 and the refresh timer reg, RTR. */
/* divisor = ((mfdcr(strap)>> 28) & 0x3); */
/* write SDRAM timing for 100MHz. */
- mtdcr (SDRAM0_CFGADDR, mem_sdtr1);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_TR);
mtdcr (SDRAM0_CFGDATA, 0x0086400D);
/* write SDRAM refresh interval register */
- mtdcr (SDRAM0_CFGADDR, mem_rtr);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_RTR);
mtdcr (SDRAM0_CFGDATA, 0x05F00000);
udelay (200);
/* sdram controller.*/
- mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_CFG);
mtdcr (SDRAM0_CFGDATA, 0x90800000);
udelay (200);
/* initially, disable ECC on all banks */
udelay (200);
- mtdcr (SDRAM0_CFGADDR, mem_ecccf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_ECCCFG);
tmp = mfdcr (SDRAM0_CFGDATA);
tmp &= 0xff0fffff;
- mtdcr (SDRAM0_CFGADDR, mem_ecccf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_ECCCFG);
mtdcr (SDRAM0_CFGDATA, tmp);
return;
}
printf ("Enable ECC..");
- mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_CFG);
tmp = (mfdcr (SDRAM0_CFGDATA) & ~0xFFE00000) | 0x90800000;
- mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_CFG);
mtdcr (SDRAM0_CFGDATA, tmp);
udelay (600);
for (p = (unsigned long) 0; ((unsigned long) p < L1_MEMSIZE); *p++ = 0L)
;
udelay (400);
- mtdcr (SDRAM0_CFGADDR, mem_ecccf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_ECCCFG);
tmp = mfdcr (SDRAM0_CFGDATA);
tmp |= 0x00800000;
mtdcr (SDRAM0_CFGDATA, tmp);
tot_size = 0;
- mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B0CR);
tmp = mfdcr (SDRAM0_CFGDATA);
if (tmp & 0x00000001) {
bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
tot_size += bank_size;
}
- mtdcr (SDRAM0_CFGADDR, mem_mb1cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B1CR);
tmp = mfdcr (SDRAM0_CFGDATA);
if (tmp & 0x00000001) {
bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
tot_size += bank_size;
}
- mtdcr (SDRAM0_CFGADDR, mem_mb2cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B2CR);
tmp = mfdcr (SDRAM0_CFGDATA);
if (tmp & 0x00000001) {
bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
tot_size += bank_size;
}
- mtdcr (SDRAM0_CFGADDR, mem_mb3cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B3CR);
tmp = mfdcr (SDRAM0_CFGDATA);
if (tmp & 0x00000001) {
bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
* Disable memory controller to allow
* values to be changed.
*/
- WDCR_SDRAM(mem_mcopt1, 0x00000000)
+ WDCR_SDRAM(SDRAM0_CFG, 0x00000000)
/*
* Configure Memory Banks
*/
- WDCR_SDRAM(mem_mb0cf, 0x00084001)
- WDCR_SDRAM(mem_mb1cf, 0x00000000)
- WDCR_SDRAM(mem_mb2cf, 0x00000000)
- WDCR_SDRAM(mem_mb3cf, 0x00000000)
+ WDCR_SDRAM(SDRAM0_B0CR, 0x00084001)
+ WDCR_SDRAM(SDRAM0_B1CR, 0x00000000)
+ WDCR_SDRAM(SDRAM0_B2CR, 0x00000000)
+ WDCR_SDRAM(SDRAM0_B3CR, 0x00000000)
/*
* Set up SDTR1 (SDRAM Timing Register)
*/
- WDCR_SDRAM(mem_sdtr1, 0x00854009)
+ WDCR_SDRAM(SDRAM0_TR, 0x00854009)
/*
* Set RTR (Refresh Timing Register)
*/
- WDCR_SDRAM(mem_rtr, 0x10000000)
- /* WDCR_SDRAM(mem_rtr, 0x05f00000) */
+ WDCR_SDRAM(SDRAM0_RTR, 0x10000000)
+ /* WDCR_SDRAM(SDRAM0_RTR, 0x05f00000) */
/********************************************************************
* Delay to ensure 200usec have elapsed since reset. Assume worst
/********************************************************************
* Set memory controller options reg, MCOPT1.
*******************************************************************/
- WDCR_SDRAM(mem_mcopt1,0x80800000)
+ WDCR_SDRAM(SDRAM0_CFG,0x80800000)
..sdri_done:
blr /* Return to calling function */
tot_size = 0;
- mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B0CR);
tmp = mfdcr (SDRAM0_CFGDATA);
if (tmp & 0x00000001) {
bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
tot_size += bank_size;
}
- mtdcr (SDRAM0_CFGADDR, mem_mb1cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B1CR);
tmp = mfdcr (SDRAM0_CFGDATA);
if (tmp & 0x00000001) {
bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
tot_size += bank_size;
}
- mtdcr (SDRAM0_CFGADDR, mem_mb2cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B2CR);
tmp = mfdcr (SDRAM0_CFGDATA);
if (tmp & 0x00000001) {
bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
tot_size += bank_size;
}
- mtdcr (SDRAM0_CFGADDR, mem_mb3cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B3CR);
tmp = mfdcr (SDRAM0_CFGDATA);
if (tmp & 0x00000001) {
bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
* Disable memory controller to allow
* values to be changed.
*/
- WDCR_SDRAM(mem_mcopt1, 0x00000000)
+ WDCR_SDRAM(SDRAM0_CFG, 0x00000000)
/*
* Configure Memory Banks
*/
- WDCR_SDRAM(mem_mb0cf, 0x00062001)
- WDCR_SDRAM(mem_mb1cf, 0x00000000)
- WDCR_SDRAM(mem_mb2cf, 0x00000000)
- WDCR_SDRAM(mem_mb3cf, 0x00000000)
+ WDCR_SDRAM(SDRAM0_B0CR, 0x00062001)
+ WDCR_SDRAM(SDRAM0_B1CR, 0x00000000)
+ WDCR_SDRAM(SDRAM0_B2CR, 0x00000000)
+ WDCR_SDRAM(SDRAM0_B3CR, 0x00000000)
/*
* Set up SDTR1 (SDRAM Timing Register)
*/
- WDCR_SDRAM(mem_sdtr1, 0x00854009)
+ WDCR_SDRAM(SDRAM0_TR, 0x00854009)
/*
* Set RTR (Refresh Timing Register)
*/
- WDCR_SDRAM(mem_rtr, 0x10000000)
- /* WDCR_SDRAM(mem_rtr, 0x05f00000) */
+ WDCR_SDRAM(SDRAM0_RTR, 0x10000000)
+ /* WDCR_SDRAM(SDRAM0_RTR, 0x05f00000) */
/********************************************************************
* Delay to ensure 200usec have elapsed since reset. Assume worst
/********************************************************************
* Set memory controller options reg, MCOPT1.
*******************************************************************/
- WDCR_SDRAM(mem_mcopt1,0x80800000)
+ WDCR_SDRAM(SDRAM0_CFG,0x80800000)
..sdri_done:
blr /* Return to calling function */
/* Set MB0CF for bank 0. (0-32MB) Address Mode 4 since 12x8(2) */
/*------------------------------------------------------------------- */
- addi r4,0,mem_mb0cf
+ addi r4,0,SDRAM0_B0CR
mtdcr SDRAM0_CFGADDR,r4
addis r4,0,MB0CF@h
ori r4,r4,MB0CF@l
/* Set MB1CF for bank 1. (32MB-64MB) Address Mode 4 since 12x8(2) */
/*------------------------------------------------------------------- */
- addi r4,0,mem_mb1cf
+ addi r4,0,SDRAM0_B1CR
mtdcr SDRAM0_CFGADDR,r4
addis r4,0,MB1CF@h
ori r4,r4,MB1CF@l
/* Set MB2CF for bank 2. off */
/*------------------------------------------------------------------- */
- addi r4,0,mem_mb2cf
+ addi r4,0,SDRAM0_B2CR
mtdcr SDRAM0_CFGADDR,r4
addis r4,0,MB2CF@h
ori r4,r4,MB2CF@l
/* Set MB3CF for bank 3. off */
/*------------------------------------------------------------------- */
- addi r4,0,mem_mb3cf
+ addi r4,0,SDRAM0_B3CR
mtdcr SDRAM0_CFGADDR,r4
addis r4,0,MB3CF@h
ori r4,r4,MB3CF@l
/*------------------------------------------------------------------- */
/* Set SDTR1 */
/*------------------------------------------------------------------- */
- addi r4,0,mem_sdtr1
+ addi r4,0,SDRAM0_TR
mtdcr SDRAM0_CFGADDR,r4
mtdcr SDRAM0_CFGDATA,r6
/*------------------------------------------------------------------- */
/* Set RTR */
/*------------------------------------------------------------------- */
- addi r4,0,mem_rtr
+ addi r4,0,SDRAM0_RTR
mtdcr SDRAM0_CFGADDR,r4
mtdcr SDRAM0_CFGDATA,r7
/* Set DC_EN to '1' and BRD_PRF to '01' for 16 byte PLB Burst */
/* read/prefetch. */
/*------------------------------------------------------------------- */
- addi r4,0,mem_mcopt1
+ addi r4,0,SDRAM0_CFG
mtdcr SDRAM0_CFGADDR,r4
addis r4,0,0x8080 /* set DC_EN=1 */
ori r4,r4,0x0000
tot_size = 0;
- mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B0CR);
tmp = mfdcr (SDRAM0_CFGDATA);
if (tmp & 0x00000001) {
bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
tot_size += bank_size;
}
- mtdcr (SDRAM0_CFGADDR, mem_mb1cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B1CR);
tmp = mfdcr (SDRAM0_CFGDATA);
if (tmp & 0x00000001) {
bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
tot_size += bank_size;
}
- mtdcr (SDRAM0_CFGADDR, mem_mb2cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B2CR);
tmp = mfdcr (SDRAM0_CFGDATA);
if (tmp & 0x00000001) {
bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
tot_size += bank_size;
}
- mtdcr (SDRAM0_CFGADDR, mem_mb3cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B3CR);
tmp = mfdcr (SDRAM0_CFGDATA);
if (tmp & 0x00000001) {
bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
/*----------------------------------------------------------- */
/* Set SDTR1 */
/*----------------------------------------------------------- */
- addi r5,0,mem_sdtr1
+ addi r5,0,SDRAM0_TR
mtdcr SDRAM0_CFGADDR,r5
mtdcr SDRAM0_CFGDATA,r4
/* Set SDRAM bank 0 register and adjust r6 for next bank */
/*------------------------------------------------------ */
- addi r7,0,mem_mb0cf
+ addi r7,0,SDRAM0_B0CR
mtdcr SDRAM0_CFGADDR,r7
mtdcr SDRAM0_CFGDATA,r6
cmpi 0, r12, 2
bne b1skip
- addi r7,0,mem_mb1cf
+ addi r7,0,SDRAM0_B1CR
mtdcr SDRAM0_CFGADDR,r7
mtdcr SDRAM0_CFGDATA,r6
/* Set SDRAM bank 2 register and adjust r6 for next bank */
/*------------------------------------------------------ */
-b1skip: addi r7,0,mem_mb2cf
+b1skip: addi r7,0,SDRAM0_B2CR
mtdcr SDRAM0_CFGADDR,r7
mtdcr SDRAM0_CFGDATA,r6
cmpi 0, r12, 2
bne b3skip
- addi r7,0,mem_mb3cf
+ addi r7,0,SDRAM0_B3CR
mtdcr SDRAM0_CFGADDR,r7
mtdcr SDRAM0_CFGDATA,r6
b3skip:
addis r7, 0, 0x05F0 /* RTR value for 100Mhz */
bl rtr_2
rtr_1: addis r7, 0, 0x03F8
-rtr_2: addi r4,0,mem_rtr
+rtr_2: addi r4,0,SDRAM0_RTR
mtdcr SDRAM0_CFGADDR,r4
mtdcr SDRAM0_CFGDATA,r7
/* Set DC_EN to '1' and BRD_PRF to '01' for 16 byte PLB Burst */
/* read/prefetch. */
/*----------------------------------------------------------- */
- addi r4,0,mem_mcopt1
+ addi r4,0,SDRAM0_CFG
mtdcr SDRAM0_CFGADDR,r4
addis r4,0,0x80C0 /* set DC_EN=1 */
ori r4,r4,0x0000
{
#define mtsdram0(reg, data) mtdcr(SDRAM0_CFGADDR,reg);mtdcr(SDRAM0_CFGDATA,data)
/* disable memcontroller so updates work */
- mtsdram0( mem_mcopt1, MEM_MCOPT1_INIT_VAL );
- mtsdram0( mem_rtr , MEM_RTR_INIT_VAL );
- mtsdram0( mem_pmit , MEM_PMIT_INIT_VAL );
- mtsdram0( mem_mb0cf , MEM_MB0CF_INIT_VAL );
- mtsdram0( mem_mb1cf , MEM_MB1CF_INIT_VAL );
- mtsdram0( mem_sdtr1 , MEM_SDTR1_INIT_VAL );
+ mtsdram0( SDRAM0_CFG, MEM_MCOPT1_INIT_VAL );
+ mtsdram0( SDRAM0_RTR , MEM_RTR_INIT_VAL );
+ mtsdram0( SDRAM0_PMIT , MEM_PMIT_INIT_VAL );
+ mtsdram0( SDRAM0_B0CR , MEM_MB0CF_INIT_VAL );
+ mtsdram0( SDRAM0_B1CR , MEM_MB1CF_INIT_VAL );
+ mtsdram0( SDRAM0_TR , MEM_SDTR1_INIT_VAL );
/* SDRAM have a power on delay, 500 micro should do */
udelay(500);
- mtsdram0( mem_mcopt1, MEM_MCOPT1_INIT_VAL|SDRAM0_CFG_ENABLE );
+ mtsdram0( SDRAM0_CFG, MEM_MCOPT1_INIT_VAL|SDRAM0_CFG_ENABLE );
return (CONFIG_SYS_SDRAM_SIZE); /* CONFIG_SYS_SDRAM_SIZE is in G2000.h */
}
/* Configure the SDRAMS */
/* disable memory controller */
- mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_CFG);
mtdcr (SDRAM0_CFGDATA, 0x00000000);
udelay (500);
/* Clear SDRAM0_BESR0 (Bus Error Syndrome Register) */
- mtdcr (SDRAM0_CFGADDR, mem_besra);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_BESR0);
mtdcr (SDRAM0_CFGDATA, 0xffffffff);
/* Clear SDRAM0_BESR1 (Bus Error Syndrome Register) */
- mtdcr (SDRAM0_CFGADDR, mem_besrb);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_BESR1);
mtdcr (SDRAM0_CFGDATA, 0xffffffff);
/* Clear SDRAM0_ECCCFG (disable ECC) */
- mtdcr (SDRAM0_CFGADDR, mem_ecccf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_ECCCFG);
mtdcr (SDRAM0_CFGDATA, 0x00000000);
/* Clear SDRAM0_ECCESR (ECC Error Syndrome Register) */
- mtdcr (SDRAM0_CFGADDR, mem_eccerr);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_ECCESR);
mtdcr (SDRAM0_CFGDATA, 0xffffffff);
/* Timing register: CASL=2, PTA=2, CTP=2, LDF=1, RFTA=5, RCD=2 */
- mtdcr (SDRAM0_CFGADDR, mem_sdtr1);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_TR);
mtdcr (SDRAM0_CFGDATA, 0x010a4016);
/* Memory Bank 0 Config == BA=0x00000000, SZ=64M, AM=3, BE=1 */
- mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B0CR);
mtdcr (SDRAM0_CFGDATA, 0x00084001);
/* Memory Bank 1 Config == BA=0x04000000, SZ=64M, AM=3, BE=1 */
- mtdcr (SDRAM0_CFGADDR, mem_mb1cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B1CR);
mtdcr (SDRAM0_CFGDATA, 0x04084001);
/* Memory Bank 2 Config == BE=0 */
- mtdcr (SDRAM0_CFGADDR, mem_mb2cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B2CR);
mtdcr (SDRAM0_CFGDATA, 0x00000000);
/* Memory Bank 3 Config == BE=0 */
- mtdcr (SDRAM0_CFGADDR, mem_mb3cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B3CR);
mtdcr (SDRAM0_CFGDATA, 0x00000000);
/* refresh timer = 0x400 */
- mtdcr (SDRAM0_CFGADDR, mem_rtr);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_RTR);
mtdcr (SDRAM0_CFGDATA, 0x04000000);
/* Power management idle timer set to the default. */
- mtdcr (SDRAM0_CFGADDR, mem_pmit);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_PMIT);
mtdcr (SDRAM0_CFGDATA, 0x07c00000);
udelay (500);
/* Enable banks (DCE=1, BPRF=1, ECCDD=1, EMDUL=1) */
- mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_CFG);
mtdcr (SDRAM0_CFGDATA, 0x80e00000);
return SDRAM_LEN;
#ifdef DEBUG
printf ("SDRAM Controller Registers --\n");
- mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_CFG);
val = mfdcr (SDRAM0_CFGDATA);
printf (" SDRAM0_CFG : 0x%08x\n", val);
val = mfdcr (SDRAM0_CFGDATA);
printf (" SDRAM0_STATUS: 0x%08x\n", val);
- mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B0CR);
val = mfdcr (SDRAM0_CFGDATA);
printf (" SDRAM0_B0CR : 0x%08x\n", val);
- mtdcr (SDRAM0_CFGADDR, mem_mb1cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B1CR);
val = mfdcr (SDRAM0_CFGDATA);
printf (" SDRAM0_B1CR : 0x%08x\n", val);
- mtdcr (SDRAM0_CFGADDR, mem_sdtr1);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_TR);
val = mfdcr (SDRAM0_CFGDATA);
printf (" SDRAM0_TR : 0x%08x\n", val);
- mtdcr (SDRAM0_CFGADDR, mem_rtr);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_RTR);
val = mfdcr (SDRAM0_CFGDATA);
printf (" SDRAM0_RTR : 0x%08x\n", val);
#endif
/* trc_clocks is sum of trp_clocks + tras_clocks */
trc_clocks = trp_clocks + tras_clocks;
/* get SDRAM timing register */
- mtdcr (SDRAM0_CFGADDR, mem_sdtr1);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_TR);
sdram_tim = mfdcr (SDRAM0_CFGDATA) & ~0x018FC01F;
/* insert CASL value */
sdram_tim |= ((unsigned long) (cal_val)) << 23;
/* insert SZ value; */
tmp |= ((unsigned long) sdram_table[i].sz << 17);
/* get SDRAM bank 0 register */
- mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B0CR);
sdram_bank = mfdcr (SDRAM0_CFGDATA) & ~0xFFCEE001;
sdram_bank |= (baseaddr | tmp | 0x01);
#endif
/* write SDRAM timing register */
- mtdcr (SDRAM0_CFGADDR, mem_sdtr1);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_TR);
mtdcr (SDRAM0_CFGDATA, sdram_tim);
#ifdef SDRAM_DEBUG
#endif
/* write SDRAM bank 0 register */
- mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B0CR);
mtdcr (SDRAM0_CFGDATA, sdram_bank);
if (get_bus_freq (tmp) > 110000000) { /* > 110MHz */
/* get SDRAM refresh interval register */
- mtdcr (SDRAM0_CFGADDR, mem_rtr);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_RTR);
tmp = mfdcr (SDRAM0_CFGDATA) & ~0x3FF80000;
tmp |= 0x07F00000;
} else {
/* get SDRAM refresh interval register */
- mtdcr (SDRAM0_CFGADDR, mem_rtr);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_RTR);
tmp = mfdcr (SDRAM0_CFGDATA) & ~0x3FF80000;
tmp |= 0x05F00000;
}
/* write SDRAM refresh interval register */
- mtdcr (SDRAM0_CFGADDR, mem_rtr);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_RTR);
mtdcr (SDRAM0_CFGDATA, tmp);
/* enable ECC if used */
#if defined(ENABLE_ECC) && !defined(CONFIG_BOOT_PCI)
#ifdef SDRAM_DEBUG
serial_puts ("disable ECC.. ");
#endif
- mtdcr (SDRAM0_CFGADDR, mem_ecccf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_ECCCFG);
tmp = mfdcr (SDRAM0_CFGDATA);
tmp &= 0xff0fffff; /* disable all banks */
- mtdcr (SDRAM0_CFGADDR, mem_ecccf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_ECCCFG);
/* set up SDRAM Controller with ECC enabled */
#ifdef SDRAM_DEBUG
serial_puts ("setup SDRAM Controller.. ");
#endif
mtdcr (SDRAM0_CFGDATA, tmp);
- mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_CFG);
tmp = (mfdcr (SDRAM0_CFGDATA) & ~0xFFE00000) | 0x90800000;
- mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_CFG);
mtdcr (SDRAM0_CFGDATA, tmp);
udelay (600);
#ifdef SDRAM_DEBUG
serial_puts ("enable ECC\n");
#endif
udelay (400);
- mtdcr (SDRAM0_CFGADDR, mem_ecccf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_ECCCFG);
tmp = mfdcr (SDRAM0_CFGDATA);
tmp |= 0x00800000; /* enable bank 0 */
mtdcr (SDRAM0_CFGDATA, tmp);
#endif
{
/* enable SDRAM controller with no ECC, 32-bit SDRAM width, 16 byte burst */
- mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_CFG);
tmp = (mfdcr (SDRAM0_CFGDATA) & ~0xFFE00000) | 0x80C00000;
- mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_CFG);
mtdcr (SDRAM0_CFGDATA, tmp);
udelay (400);
}
ds = 0;
/* since the DRAM controller is allready set up, calculate the size with the
bank registers */
- mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B0CR);
bank_reg[0] = mfdcr (SDRAM0_CFGDATA);
- mtdcr (SDRAM0_CFGADDR, mem_mb1cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B1CR);
bank_reg[1] = mfdcr (SDRAM0_CFGDATA);
- mtdcr (SDRAM0_CFGADDR, mem_mb2cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B2CR);
bank_reg[2] = mfdcr (SDRAM0_CFGDATA);
- mtdcr (SDRAM0_CFGADDR, mem_mb3cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B3CR);
bank_reg[3] = mfdcr (SDRAM0_CFGDATA);
TotalSize = 0;
for (i = 0; i < 4; i++) {
} else
ds = 1;
}
- mtdcr (SDRAM0_CFGADDR, mem_ecccf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_ECCCFG);
tmp = mfdcr (SDRAM0_CFGDATA);
if (!tmp)
SDRAM_err ("unsupported SDRAM");
/* get SDRAM timing register */
- mtdcr (SDRAM0_CFGADDR, mem_sdtr1);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_TR);
tmp = mfdcr (SDRAM0_CFGDATA) & ~0x018FC01F;
/* insert CASL value */
/* tmp |= ((unsigned long)cal_val) << 23; */
#endif
/* write SDRAM timing register */
- mtdcr (SDRAM0_CFGADDR, mem_sdtr1);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_TR);
mtdcr (SDRAM0_CFGDATA, tmp);
baseaddr = CONFIG_SYS_SDRAM_BASE;
bank_size = (((unsigned long) density) << 22) / 2;
SDRAM_err ("unsupported SDRAM");
} /* endswitch */
/* get SDRAM bank 0 register */
- mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B0CR);
bank = mfdcr (SDRAM0_CFGDATA) & ~0xFFCEE001;
bank |= (baseaddr | tmp | 0x01);
#ifdef SDRAM_DEBUG
sdram_size += bank_size;
/* write SDRAM bank 0 register */
- mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B0CR);
mtdcr (SDRAM0_CFGDATA, bank);
/* get SDRAM bank 1 register */
- mtdcr (SDRAM0_CFGADDR, mem_mb1cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B1CR);
bank = mfdcr (SDRAM0_CFGDATA) & ~0xFFCEE001;
sdram_size = 0;
serial_puts ("\n");
#endif
/* write SDRAM bank 1 register */
- mtdcr (SDRAM0_CFGADDR, mem_mb1cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B1CR);
mtdcr (SDRAM0_CFGDATA, bank);
/* get SDRAM bank 2 register */
- mtdcr (SDRAM0_CFGADDR, mem_mb2cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B2CR);
bank = mfdcr (SDRAM0_CFGDATA) & ~0xFFCEE001;
bank |= (baseaddr | tmp | 0x01);
sdram_size += bank_size;
/* write SDRAM bank 2 register */
- mtdcr (SDRAM0_CFGADDR, mem_mb2cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B2CR);
mtdcr (SDRAM0_CFGDATA, bank);
/* get SDRAM bank 3 register */
- mtdcr (SDRAM0_CFGADDR, mem_mb3cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B3CR);
bank = mfdcr (SDRAM0_CFGDATA) & ~0xFFCEE001;
#ifdef SDRAM_DEBUG
#endif
/* write SDRAM bank 3 register */
- mtdcr (SDRAM0_CFGADDR, mem_mb3cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B3CR);
mtdcr (SDRAM0_CFGDATA, bank);
/* get SDRAM refresh interval register */
- mtdcr (SDRAM0_CFGADDR, mem_rtr);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_RTR);
tmp = mfdcr (SDRAM0_CFGDATA) & ~0x3FF80000;
if (tmemclk < NSto10PS (16))
tmp |= 0x03F80000;
/* write SDRAM refresh interval register */
- mtdcr (SDRAM0_CFGADDR, mem_rtr);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_RTR);
mtdcr (SDRAM0_CFGDATA, tmp);
/* enable SDRAM controller with no ECC, 32-bit SDRAM width, 16 byte burst */
- mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_CFG);
tmp = (mfdcr (SDRAM0_CFGDATA) & ~0xFFE00000) | 0x80E00000;
- mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_CFG);
mtdcr (SDRAM0_CFGDATA, tmp);
/* since the DRAM controller is allready set up,
* calculate the size with the bank registers
*/
- mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B0CR);
bank_reg[0] = mfdcr (SDRAM0_CFGDATA);
- mtdcr (SDRAM0_CFGADDR, mem_mb1cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B1CR);
bank_reg[1] = mfdcr (SDRAM0_CFGDATA);
- mtdcr (SDRAM0_CFGADDR, mem_mb2cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B2CR);
bank_reg[2] = mfdcr (SDRAM0_CFGDATA);
- mtdcr (SDRAM0_CFGADDR, mem_mb3cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B3CR);
bank_reg[3] = mfdcr (SDRAM0_CFGDATA);
TotalSize = 0;
for (i = 0; i < 4; i++) {
u32 value;
printf("SDRAM Controller Registers --\n");
- mfsdram(mem_mcopt1, value);
+ mfsdram(SDRAM0_CFG, value);
printf(" SDRAM0_CFG : 0x%08x\n", value);
- mfsdram(mem_status, value);
+ mfsdram(SDRAM0_STATUS, value);
printf(" SDRAM0_STATUS: 0x%08x\n", value);
- mfsdram(mem_mb0cf, value);
+ mfsdram(SDRAM0_B0CR, value);
printf(" SDRAM0_B0CR : 0x%08x\n", value);
- mfsdram(mem_mb1cf, value);
+ mfsdram(SDRAM0_B1CR, value);
printf(" SDRAM0_B1CR : 0x%08x\n", value);
- mfsdram(mem_sdtr1, value);
+ mfsdram(SDRAM0_TR, value);
printf(" SDRAM0_TR : 0x%08x\n", value);
- mfsdram(mem_rtr, value);
+ mfsdram(SDRAM0_RTR, value);
printf(" SDRAM0_RTR : 0x%08x\n", value);
}
#endif
printf(__FUNCTION__);
#endif
/* disable memory controller */
- mtsdram(mem_mcopt1, 0x00000000);
+ mtsdram(SDRAM0_CFG, 0x00000000);
udelay (500);
/* Clear SDRAM0_BESR0 (Bus Error Syndrome Register) */
- mtsdram(mem_besra, 0xffffffff);
+ mtsdram(SDRAM0_BESR0, 0xffffffff);
/* Clear SDRAM0_BESR1 (Bus Error Syndrome Register) */
- mtsdram(mem_besrb, 0xffffffff);
+ mtsdram(SDRAM0_BESR1, 0xffffffff);
/* Clear SDRAM0_ECCCFG (disable ECC) */
- mtsdram(mem_ecccf, 0x00000000);
+ mtsdram(SDRAM0_ECCCFG, 0x00000000);
/* Clear SDRAM0_ECCESR (ECC Error Syndrome Register) */
- mtsdram(mem_eccerr, 0xffffffff);
+ mtsdram(SDRAM0_ECCESR, 0xffffffff);
/* Timing register: CASL=2, PTA=2, CTP=2, LDF=1, RFTA=5, RCD=2
*/
- mtsdram(mem_sdtr1, 0x008a4015);
+ mtsdram(SDRAM0_TR, 0x008a4015);
/* Memory Bank 0 Config == BA=0x00000000, SZ=64M, AM=3, BE=1
* and refresh timer
*/
switch (dram_size >> 20) {
case 32:
- mtsdram(mem_mb0cf, 0x00062001);
- mtsdram(mem_rtr, 0x07F00000);
+ mtsdram(SDRAM0_B0CR, 0x00062001);
+ mtsdram(SDRAM0_RTR, 0x07F00000);
break;
case 64:
- mtsdram(mem_mb0cf, 0x00084001);
- mtsdram(mem_rtr, 0x04100000);
+ mtsdram(SDRAM0_B0CR, 0x00084001);
+ mtsdram(SDRAM0_RTR, 0x04100000);
break;
case 128:
- mtsdram(mem_mb0cf, 0x000A4001);
- mtsdram(mem_rtr, 0x04100000);
+ mtsdram(SDRAM0_B0CR, 0x000A4001);
+ mtsdram(SDRAM0_RTR, 0x04100000);
break;
default:
printf("Invalid memory size of %d MB given\n", dram_size >> 20);
}
/* Power management idle timer set to the default. */
- mtsdram(mem_pmit, 0x07c00000);
+ mtsdram(SDRAM0_PMIT, 0x07c00000);
udelay (500);
/* Enable banks (DCE=1, BPRF=1, ECCDD=1, EMDUL=1) TODO */
- mtsdram(mem_mcopt1, 0x90800000);
+ mtsdram(SDRAM0_CFG, 0x90800000);
#ifdef DEBUG
printf("%s: done\n", __FUNCTION__);
/*--------------------------------------------------------------------
* Setup some default
*------------------------------------------------------------------*/
- mtsdram (mem_uabba, 0x00000000); /* ubba=0 (default) */
- mtsdram (mem_slio, 0x00000000); /* rdre=0 wrre=0 rarw=0 */
- mtsdram (mem_devopt, 0x00000000); /* dll=0 ds=0 (normal) */
- mtsdram (mem_wddctr, 0x00000000); /* wrcp=0 dcd=0 */
- mtsdram (mem_clktr, 0x40000000); /* clkp=1 (90 deg wr) dcdt=0 */
+ mtsdram (SDRAM0_UABBA, 0x00000000); /* ubba=0 (default) */
+ mtsdram (SDRAM0_SLIO, 0x00000000); /* rdre=0 wrre=0 rarw=0 */
+ mtsdram (SDRAM0_DEVOPT, 0x00000000); /* dll=0 ds=0 (normal) */
+ mtsdram (SDRAM0_WDDCTR, 0x00000000); /* wrcp=0 dcd=0 */
+ mtsdram (SDRAM0_CLKTR, 0x40000000); /* clkp=1 (90 deg wr) dcdt=0 */
/*--------------------------------------------------------------------
* Setup for board-specific specific mem
/*
* Following for CAS Latency = 2.5 @ 133 MHz PLB
*/
- mtsdram (mem_b0cr, 0x000a4001); /* SDBA=0x000 128MB, Mode 3, enabled */
- mtsdram (mem_tr0, 0x410a4012); /* WR=2 WD=1 CL=2.5 PA=3 CP=4 LD=2 */
+ mtsdram (SDRAM0_B0CR, 0x000a4001); /* SDBA=0x000 128MB, Mode 3, enabled */
+ mtsdram (SDRAM0_TR0, 0x410a4012); /* WR=2 WD=1 CL=2.5 PA=3 CP=4 LD=2 */
/* RA=10 RD=3 */
- mtsdram (mem_tr1, 0x8080082f); /* SS=T2 SL=STAGE 3 CD=1 CT=0x02f */
- mtsdram (mem_rtr, 0x08200000); /* Rate 15.625 ns @ 133 MHz PLB */
- mtsdram (mem_cfg1, 0x00000000); /* Self-refresh exit, disable PM */
+ mtsdram (SDRAM0_TR1, 0x8080082f); /* SS=T2 SL=STAGE 3 CD=1 CT=0x02f */
+ mtsdram (SDRAM0_RTR, 0x08200000); /* Rate 15.625 ns @ 133 MHz PLB */
+ mtsdram (SDRAM0_CFG1, 0x00000000); /* Self-refresh exit, disable PM */
udelay (400); /* Delay 200 usecs (min) */
/*--------------------------------------------------------------------
* Enable the controller, then wait for DCEN to complete
*------------------------------------------------------------------*/
- mtsdram (mem_cfg0, 0x86000000); /* DCEN=1, PMUD=1, 64-bit */
+ mtsdram (SDRAM0_CFG0, 0x86000000); /* DCEN=1, PMUD=1, 64-bit */
for (;;) {
- mfsdram (mem_mcsts, reg);
+ mfsdram (SDRAM0_MCSTS, reg);
if (reg & 0x80000000)
break;
}
}
#ifdef SC3_DEBUGOUT
-static unsigned int mbcf[] = {mem_mb0cf, mem_mb1cf, mem_mb2cf, mem_mb3cf};
+static unsigned int mbcf[] = {SDRAM0_B0CR, SDRAM0_B1CR, SDRAM0_B2CR, SDRAM0_B3CR};
#endif
phys_size_t initdram (int board_type)
puts("\nSDRAM configuration:\n");
- mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_CFG);
ul1 = mfdcr(SDRAM0_CFGDATA);
if (!(ul1 & 0x80000000)) {
mems += printSDRAMConfig (i, ul1);
}
- mtdcr (SDRAM0_CFGADDR, mem_sdtr1);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_TR);
ul1 = mfdcr(SDRAM0_CFGDATA);
printf ("Timing:\n -CAS latency %lu\n", ((ul1 & 0x1800000) >> 23)+1);
printf (" -CAS to RAS %lu\n", ((ul1 & 0x1C) >> 2) + 4);
printf (" -RAS to CAS %lu\n", ((ul1 & 0x3) + 1));
puts ("Misc:\n");
- mtdcr (SDRAM0_CFGADDR, mem_rtr);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_RTR);
ul1 = mfdcr(SDRAM0_CFGDATA);
printf (" -Refresh rate: %luns\n", (ul1 >> 16) * 7);
- mtdcr(SDRAM0_CFGADDR,mem_pmit);
+ mtdcr(SDRAM0_CFGADDR,SDRAM0_PMIT);
ul2=mfdcr(SDRAM0_CFGDATA);
- mtdcr(SDRAM0_CFGADDR,mem_mcopt1);
+ mtdcr(SDRAM0_CFGADDR,SDRAM0_CFG);
ul1=mfdcr(SDRAM0_CFGDATA);
if (ul1 & 0x20000000)
else
puts(" -Memory lines only at write cycles active outputs\n");
- mtdcr (SDRAM0_CFGADDR, mem_status);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_STATUS);
ul1 = mfdcr (SDRAM0_CFGDATA);
if (ul1 & 0x80000000)
puts(" -SDRAM Controller ready\n");
return (mems * 1024 * 1024);
#else
- mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B0CR);
ul1 = mfdcr (SDRAM0_CFGDATA);
mems = printSDRAMConfig (0, ul1);
- mtdcr (SDRAM0_CFGADDR, mem_mb1cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B1CR);
ul1 = mfdcr (SDRAM0_CFGDATA);
mems += printSDRAMConfig (1, ul1);
- mtdcr (SDRAM0_CFGADDR, mem_mb2cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B2CR);
ul1 = mfdcr(SDRAM0_CFGDATA);
mems += printSDRAMConfig (2, ul1);
- mtdcr (SDRAM0_CFGADDR, mem_mb3cf);
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B3CR);
ul1 = mfdcr(SDRAM0_CFGDATA);
mems += printSDRAMConfig (3, ul1);
* Disable memory controller to allow
* values to be changed.
*/
- addi r3, 0, mem_mcopt1
+ addi r3, 0, SDRAM0_CFG
mtdcr SDRAM0_CFGADDR, r3
addis r4, 0, 0x0
ori r4, r4, 0x0
* Set MB0CF for ext bank 0. (0-4MB) Address Mode 5 since 11x8x2
* All other banks are disabled.
*/
- addi r3, 0, mem_mb0cf
+ addi r3, 0, SDRAM0_B0CR
mtdcr SDRAM0_CFGADDR, r3
addis r4, 0, 0x0000 /* BA=0x0, SZ=4MB */
ori r4, r4, 0x8001 /* Mode is 5, 11x8x2or4, BE=Enabled */
/*
* Set up SDTR1
*/
- addi r3, 0, mem_sdtr1
+ addi r3, 0, SDRAM0_TR
mtdcr SDRAM0_CFGADDR, r3
addis r4, 0, 0x0086 /* SDTR1 value for 100Mhz */
ori r4, r4, 0x400D
/*
* Set RTR
*/
- addi r3, 0, mem_rtr
+ addi r3, 0, SDRAM0_RTR
mtdcr SDRAM0_CFGADDR, r3
addis r4, 0, 0x05F0 /* RTR refresh val = 15.625ms@100Mhz */
mtdcr SDRAM0_CFGDATA, r4
/********************************************************************
* Set memory controller options reg, MCOPT1.
*******************************************************************/
- addi r3, 0, mem_mcopt1
+ addi r3, 0, SDRAM0_CFG
mtdcr SDRAM0_CFGADDR, r3
addis r4, 0, 0x80E0 /* DC_EN=1,SRE=0,PME=0,MEMCHK=0 */
ori r4, r4, 0x0000 /* REGEN=0,DRW=00,BRPF=01,ECCDD=1 */
int size = 0;
/* Get bank Size registers */
- mtdcr (SDRAM0_CFGADDR, mem_mb0cf); /* get bank 0 config reg */
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B0CR); /* get bank 0 config reg */
regs[0] = mfdcr (SDRAM0_CFGDATA);
- mtdcr (SDRAM0_CFGADDR, mem_mb1cf); /* get bank 1 config reg */
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B1CR); /* get bank 1 config reg */
regs[1] = mfdcr (SDRAM0_CFGDATA);
- mtdcr (SDRAM0_CFGADDR, mem_mb2cf); /* get bank 2 config reg */
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B2CR); /* get bank 2 config reg */
regs[2] = mfdcr (SDRAM0_CFGDATA);
- mtdcr (SDRAM0_CFGADDR, mem_mb3cf); /* get bank 3 config reg */
+ mtdcr (SDRAM0_CFGADDR, SDRAM0_B3CR); /* get bank 3 config reg */
regs[3] = mfdcr (SDRAM0_CFGDATA);
/* compute the size, add each bank if enabled */
puts ("\nMemory (SDRAM) Configuration\n"
"besra besrsa besrb besrsb bear mcopt1 rtr pmit\n");
- mtdcr(SDRAM0_CFGADDR,mem_besra); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
- mtdcr(SDRAM0_CFGADDR,mem_besrsa); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
- mtdcr(SDRAM0_CFGADDR,mem_besrb); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
- mtdcr(SDRAM0_CFGADDR,mem_besrsb); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
- mtdcr(SDRAM0_CFGADDR,mem_bear); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
- mtdcr(SDRAM0_CFGADDR,mem_mcopt1); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
- mtdcr(SDRAM0_CFGADDR,mem_rtr); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
- mtdcr(SDRAM0_CFGADDR,mem_pmit); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
+ mtdcr(SDRAM0_CFGADDR,SDRAM0_BESR0); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
+ mtdcr(SDRAM0_CFGADDR,SDRAM0_BESRS0); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
+ mtdcr(SDRAM0_CFGADDR,SDRAM0_BESR1); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
+ mtdcr(SDRAM0_CFGADDR,SDRAM0_BESRS1); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
+ mtdcr(SDRAM0_CFGADDR,SDRAM0_BEAR); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
+ mtdcr(SDRAM0_CFGADDR,SDRAM0_CFG); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
+ mtdcr(SDRAM0_CFGADDR,SDRAM0_RTR); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
+ mtdcr(SDRAM0_CFGADDR,SDRAM0_PMIT); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
puts ("\n"
"mb0cf mb1cf mb2cf mb3cf sdtr1 ecccf eccerr\n");
- mtdcr(SDRAM0_CFGADDR,mem_mb0cf); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
- mtdcr(SDRAM0_CFGADDR,mem_mb1cf); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
- mtdcr(SDRAM0_CFGADDR,mem_mb2cf); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
- mtdcr(SDRAM0_CFGADDR,mem_mb3cf); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
- mtdcr(SDRAM0_CFGADDR,mem_sdtr1); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
- mtdcr(SDRAM0_CFGADDR,mem_ecccf); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
- mtdcr(SDRAM0_CFGADDR,mem_eccerr); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
+ mtdcr(SDRAM0_CFGADDR,SDRAM0_B0CR); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
+ mtdcr(SDRAM0_CFGADDR,SDRAM0_B1CR); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
+ mtdcr(SDRAM0_CFGADDR,SDRAM0_B2CR); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
+ mtdcr(SDRAM0_CFGADDR,SDRAM0_B3CR); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
+ mtdcr(SDRAM0_CFGADDR,SDRAM0_TR); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
+ mtdcr(SDRAM0_CFGADDR,SDRAM0_ECCCFG); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
+ mtdcr(SDRAM0_CFGADDR,SDRAM0_ECCESR); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
printf ("\n\n"
"DMA Channels\n"
puts ("\nMemory (SDRAM) Configuration\n"
"mcopt1 rtr pmit mb0cf mb1cf sdtr1\n");
- mtdcr(SDRAM0_CFGADDR,mem_mcopt1); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
- mtdcr(SDRAM0_CFGADDR,mem_rtr); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
- mtdcr(SDRAM0_CFGADDR,mem_pmit); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
- mtdcr(SDRAM0_CFGADDR,mem_mb0cf); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
- mtdcr(SDRAM0_CFGADDR,mem_mb1cf); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
- mtdcr(SDRAM0_CFGADDR,mem_sdtr1); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
+ mtdcr(SDRAM0_CFGADDR,SDRAM0_CFG); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
+ mtdcr(SDRAM0_CFGADDR,SDRAM0_RTR); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
+ mtdcr(SDRAM0_CFGADDR,SDRAM0_PMIT); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
+ mtdcr(SDRAM0_CFGADDR,SDRAM0_B0CR); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
+ mtdcr(SDRAM0_CFGADDR,SDRAM0_B1CR); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
+ mtdcr(SDRAM0_CFGADDR,SDRAM0_TR); printf ("%08x ", mfdcr(SDRAM0_CFGDATA));
printf ("\n\n"
"DMA Channels\n"
#define mtsdram0(reg, data) mtdcr(SDRAM0_CFGADDR,reg);mtdcr(SDRAM0_CFGDATA,data)
/* disable memcontroller so updates work */
- mtsdram0( mem_mcopt1, 0 );
+ mtsdram0( SDRAM0_CFG, 0 );
#ifndef CONFIG_405EP /* not on PPC405EP */
- mtsdram0( mem_besra , sdram0_besr0 );
- mtsdram0( mem_besrb , sdram0_besr1 );
- mtsdram0( mem_ecccf , sdram0_ecccfg );
- mtsdram0( mem_eccerr, sdram0_eccesr );
+ mtsdram0( SDRAM0_BESR0 , sdram0_besr0 );
+ mtsdram0( SDRAM0_BESR1 , sdram0_besr1 );
+ mtsdram0( SDRAM0_ECCCFG , sdram0_ecccfg );
+ mtsdram0( SDRAM0_ECCESR, sdram0_eccesr );
#endif
- mtsdram0( mem_rtr , sdram0_rtr );
- mtsdram0( mem_pmit , sdram0_pmit );
- mtsdram0( mem_mb0cf , sdram0_b0cr );
- mtsdram0( mem_mb1cf , sdram0_b1cr );
+ mtsdram0( SDRAM0_RTR , sdram0_rtr );
+ mtsdram0( SDRAM0_PMIT , sdram0_pmit );
+ mtsdram0( SDRAM0_B0CR , sdram0_b0cr );
+ mtsdram0( SDRAM0_B1CR , sdram0_b1cr );
#ifndef CONFIG_405EP /* not on PPC405EP */
- mtsdram0( mem_mb2cf , sdram0_b2cr );
- mtsdram0( mem_mb3cf , sdram0_b3cr );
+ mtsdram0( SDRAM0_B2CR , sdram0_b2cr );
+ mtsdram0( SDRAM0_B3CR , sdram0_b3cr );
#endif
- mtsdram0( mem_sdtr1 , sdram0_tr );
+ mtsdram0( SDRAM0_TR , sdram0_tr );
/* SDRAM have a power on delay, 500 micro should do */
udelay(500);
sdram0_cfg = SDRAM0_CFG_DCE | SDRAM0_CFG_BRPF(1) | SDRAM0_CFG_ECCDD | SDRAM0_CFG_EMDULR;
if (ecc_on)
sdram0_cfg |= SDRAM0_CFG_MEMCHK;
- mtsdram0(mem_mcopt1, sdram0_cfg);
+ mtsdram0(SDRAM0_CFG, sdram0_cfg);
return (total_size);
}
/*
* program SDRAM Clock Timing Register (SDRAM0_CLKTR)
*/
- mtsdram(mem_clktr, 0x40000000);
+ mtsdram(SDRAM0_CLKTR, 0x40000000);
/*
* delay to ensure 200 usec has elapsed
/*
* enable the memory controller
*/
- mfsdram(mem_cfg0, cfg0);
- mtsdram(mem_cfg0, cfg0 | SDRAM_CFG0_DCEN);
+ mfsdram(SDRAM0_CFG0, cfg0);
+ mtsdram(SDRAM0_CFG0, cfg0 | SDRAM_CFG0_DCEN);
/*
* wait for SDRAM_CFG0_DC_EN to complete
*/
while (1) {
- mfsdram(mem_mcsts, mcsts);
+ mfsdram(SDRAM0_MCSTS, mcsts);
if ((mcsts & SDRAM_MCSTS_MRSC) != 0)
break;
}
/*
* get Memory Controller Options 0 data
*/
- mfsdram(mem_cfg0, cfg0);
+ mfsdram(SDRAM0_CFG0, cfg0);
/*
* clear bits
* Note: DCEN must be enabled after all DDR SDRAM controller
* configuration registers get initialized.
*/
- mtsdram(mem_cfg0, cfg0);
+ mtsdram(SDRAM0_CFG0, cfg0);
}
static void program_cfg1(unsigned long *dimm_populated,
unsigned long num_dimm_banks)
{
unsigned long cfg1;
- mfsdram(mem_cfg1, cfg1);
+ mfsdram(SDRAM0_CFG1, cfg1);
/*
* Self-refresh exit, disable PM
/*
* program Memory Controller Options 1
*/
- mtsdram(mem_cfg1, cfg1);
+ mtsdram(SDRAM0_CFG1, cfg1);
}
static void program_rtr(unsigned long *dimm_populated,
/*
* program Refresh Timer Register (SDRAM0_RTR)
*/
- mtsdram(mem_rtr, sdram_rtr);
+ mtsdram(SDRAM0_RTR, sdram_rtr);
}
static void program_tr0(unsigned long *dimm_populated,
/*
* get SDRAM Timing Register 0 (SDRAM_TR0) and clear bits
*/
- mfsdram(mem_tr0, tr0);
+ mfsdram(SDRAM0_TR0, tr0);
tr0 &= ~(SDRAM_TR0_SDWR_MASK | SDRAM_TR0_SDWD_MASK |
SDRAM_TR0_SDCL_MASK | SDRAM_TR0_SDPA_MASK |
SDRAM_TR0_SDCP_MASK | SDRAM_TR0_SDLD_MASK |
}
debug("tr0: %x\n", tr0);
- mtsdram(mem_tr0, tr0);
+ mtsdram(SDRAM0_TR0, tr0);
}
static int short_mem_test(void)
0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55}};
for (bxcr_num = 0; bxcr_num < MAXBXCR; bxcr_num++) {
- mtdcr(SDRAM0_CFGADDR, mem_b0cr + (bxcr_num << 2));
+ mtdcr(SDRAM0_CFGADDR, SDRAM0_B0CR + (bxcr_num << 2));
if ((mfdcr(SDRAM0_CFGDATA) & SDRAM_BXCR_SDBE) == SDRAM_BXCR_SDBE) {
/* Bank is enabled */
membase = (unsigned long*)
/*
* get SDRAM Timing Register 0 (SDRAM_TR0) and clear bits
*/
- mfsdram(mem_tr1, tr1);
+ mfsdram(SDRAM0_TR1, tr1);
tr1 &= ~(SDRAM_TR1_RDSS_MASK | SDRAM_TR1_RDSL_MASK |
SDRAM_TR1_RDCD_MASK | SDRAM_TR1_RDCT_MASK);
- mfsdram(mem_tr0, tr0);
+ mfsdram(SDRAM0_TR0, tr0);
if (((tr0 & SDRAM_TR0_SDCL_MASK) == SDRAM_TR0_SDCL_2_5_CLK) &&
(sys_info.freqPLB > 100000000)) {
tr1 |= SDRAM_TR1_RDSS_TR2;
/*
* save CFG0 ECC setting to a temporary variable and turn ECC off
*/
- mfsdram(mem_cfg0, cfg0);
+ mfsdram(SDRAM0_CFG0, cfg0);
ecc_temp = cfg0 & SDRAM_CFG0_MCHK_MASK;
- mtsdram(mem_cfg0, (cfg0 & ~SDRAM_CFG0_MCHK_MASK) | SDRAM_CFG0_MCHK_NON);
+ mtsdram(SDRAM0_CFG0, (cfg0 & ~SDRAM_CFG0_MCHK_MASK) | SDRAM_CFG0_MCHK_NON);
/*
* get the delay line calibration register value
*/
- mfsdram(mem_dlycal, dlycal);
+ mfsdram(SDRAM0_DLYCAL, dlycal);
dly_val = SDRAM_DLYCAL_DLCV_DECODE(dlycal) << 2;
max_pass_length = 0;
/*
* Set the timing reg for the test.
*/
- mtsdram(mem_tr1, (tr1 | SDRAM_TR1_RDCT_ENCODE(rdclt)));
+ mtsdram(SDRAM0_TR1, (tr1 | SDRAM_TR1_RDCT_ENCODE(rdclt)));
if (short_mem_test()) {
if (fail_found == TRUE) {
/*
* restore the orignal ECC setting
*/
- mtsdram(mem_cfg0, (cfg0 & ~SDRAM_CFG0_MCHK_MASK) | ecc_temp);
+ mtsdram(SDRAM0_CFG0, (cfg0 & ~SDRAM_CFG0_MCHK_MASK) | ecc_temp);
/*
* set the SDRAM TR1 RDCD value
/*
* program SDRAM Timing Register 1 TR1
*/
- mtsdram(mem_tr1, tr1);
+ mtsdram(SDRAM0_TR1, tr1);
}
static unsigned long program_bxcr(unsigned long *dimm_populated,
* Set the BxCR regs. First, wipe out the bank config registers.
*/
for (bx_cr_num = 0; bx_cr_num < MAXBXCR; bx_cr_num++) {
- mtdcr(SDRAM0_CFGADDR, mem_b0cr + (bx_cr_num << 2));
+ mtdcr(SDRAM0_CFGADDR, SDRAM0_B0CR + (bx_cr_num << 2));
mtdcr(SDRAM0_CFGDATA, 0x00000000);
bank_parms[bx_cr_num].bank_size_bytes = 0;
}
/* Set the SDRAM0_BxCR regs thanks to sort tables */
for (bx_cr_num = 0, bank_base_addr = 0; bx_cr_num < MAXBXCR; bx_cr_num++) {
if (bank_parms[sorted_bank_num[bx_cr_num]].bank_size_bytes) {
- mtdcr(SDRAM0_CFGADDR, mem_b0cr + (sorted_bank_num[bx_cr_num] << 2));
+ mtdcr(SDRAM0_CFGADDR, SDRAM0_B0CR + (sorted_bank_num[bx_cr_num] << 2));
temp = mfdcr(SDRAM0_CFGDATA) & ~(SDRAM_BXCR_SDBA_MASK | SDRAM_BXCR_SDSZ_MASK |
SDRAM_BXCR_SDAM_MASK | SDRAM_BXCR_SDBE);
temp = temp | (bank_base_addr & SDRAM_BXCR_SDBA_MASK) |
/*
* Disable memory controller.
*/
- mtsdram(mem_mcopt1, 0x00000000);
+ mtsdram(SDRAM0_CFG, 0x00000000);
/*
* Set MB0CF for bank 0.
*/
- mtsdram(mem_mb0cf, mb0cf[i].reg);
- mtsdram(mem_sdtr1, sdtr1);
- mtsdram(mem_rtr, compute_rtr(speed, mb0cf[i].rows, 64));
+ mtsdram(SDRAM0_B0CR, mb0cf[i].reg);
+ mtsdram(SDRAM0_TR, sdtr1);
+ mtsdram(SDRAM0_RTR, compute_rtr(speed, mb0cf[i].rows, 64));
udelay(200);
* Set DC_EN to '1' and BRD_PRF to '01' for 16 byte PLB Burst
* read/prefetch.
*/
- mtsdram(mem_mcopt1, 0x80800000);
+ mtsdram(SDRAM0_CFG, 0x80800000);
udelay(10000);
* defined (assumes same type as bank 0)
*/
#ifdef CONFIG_SDRAM_BANK1
- mtsdram(mem_mcopt1, 0x00000000);
- mtsdram(mem_mb1cf, mb0cf[i].size | mb0cf[i].reg);
- mtsdram(mem_mcopt1, 0x80800000);
+ mtsdram(SDRAM0_CFG, 0x00000000);
+ mtsdram(SDRAM0_B1CR, mb0cf[i].size | mb0cf[i].reg);
+ mtsdram(SDRAM0_CFG, 0x80800000);
udelay(10000);
/*
*/
if (get_ram_size((long *)mb0cf[i].size, mb0cf[i].size) !=
mb0cf[i].size) {
- mtsdram(mem_mb1cf, 0);
- mtsdram(mem_mcopt1, 0);
+ mtsdram(SDRAM0_B1CR, 0);
+ mtsdram(SDRAM0_CFG, 0);
} else {
/*
* We have two identical banks, so the size
/* go through all possible SDRAM0_TR1[RDCT] values */
for (i=0; i<=0x1ff; i++) {
/* set the current value for TR1 */
- mtsdram(mem_tr1, (0x80800800 | i));
+ mtsdram(SDRAM0_TR1, (0x80800800 | i));
/* write values */
for (j=0; j<NUM_TRIES; j++) {
/*
* Disable memory controller.
*/
- mtsdram(mem_cfg0, 0x00000000);
+ mtsdram(SDRAM0_CFG0, 0x00000000);
/*
* Setup some default
*/
- mtsdram(mem_uabba, 0x00000000); /* ubba=0 (default) */
- mtsdram(mem_slio, 0x00000000); /* rdre=0 wrre=0 rarw=0 */
- mtsdram(mem_devopt, 0x00000000); /* dll=0 ds=0 (normal) */
- mtsdram(mem_wddctr, CONFIG_SYS_SDRAM0_WDDCTR);
- mtsdram(mem_clktr, 0x40000000); /* clkp=1 (90 deg wr) dcdt=0 */
+ mtsdram(SDRAM0_UABBA, 0x00000000); /* ubba=0 (default) */
+ mtsdram(SDRAM0_SLIO, 0x00000000); /* rdre=0 wrre=0 rarw=0 */
+ mtsdram(SDRAM0_DEVOPT, 0x00000000); /* dll=0 ds=0 (normal) */
+ mtsdram(SDRAM0_WDDCTR, CONFIG_SYS_SDRAM0_WDDCTR);
+ mtsdram(SDRAM0_CLKTR, 0x40000000); /* clkp=1 (90 deg wr) dcdt=0 */
/*
* Following for CAS Latency = 2.5 @ 133 MHz PLB
*/
- mtsdram(mem_b0cr, mb0cf[i].reg);
- mtsdram(mem_tr0, CONFIG_SYS_SDRAM0_TR0);
- mtsdram(mem_tr1, 0x80800800); /* SS=T2 SL=STAGE 3 CD=1 CT=0x00*/
- mtsdram(mem_rtr, CONFIG_SYS_SDRAM0_RTR);
- mtsdram(mem_cfg1, 0x00000000); /* Self-refresh exit, disable PM*/
+ mtsdram(SDRAM0_B0CR, mb0cf[i].reg);
+ mtsdram(SDRAM0_TR0, CONFIG_SYS_SDRAM0_TR0);
+ mtsdram(SDRAM0_TR1, 0x80800800); /* SS=T2 SL=STAGE 3 CD=1 CT=0x00*/
+ mtsdram(SDRAM0_RTR, CONFIG_SYS_SDRAM0_RTR);
+ mtsdram(SDRAM0_CFG1, 0x00000000); /* Self-refresh exit, disable PM*/
udelay(400); /* Delay 200 usecs (min) */
/*
* Enable the controller, then wait for DCEN to complete
*/
- mtsdram(mem_cfg0, CONFIG_SYS_SDRAM0_CFG0);
+ mtsdram(SDRAM0_CFG0, CONFIG_SYS_SDRAM0_CFG0);
udelay(10000);
if (get_ram_size(0, mb0cf[i].size) == mb0cf[i].size) {
* Optimize TR1 to current hardware environment
*/
sdram_tr1_set(0x00000000, &tr1_bank1);
- mtsdram(mem_tr1, (tr1_bank1 | 0x80800800));
+ mtsdram(SDRAM0_TR1, (tr1_bank1 | 0x80800800));
/*
* defined (assumes same type as bank 0)
*/
#ifdef CONFIG_SDRAM_BANK1
- mtsdram(mem_cfg0, 0);
- mtsdram(mem_b1cr, mb0cf[i].size | mb0cf[i].reg);
- mtsdram(mem_cfg0, CONFIG_SYS_SDRAM0_CFG0);
+ mtsdram(SDRAM0_CFG0, 0);
+ mtsdram(SDRAM0_B1CR, mb0cf[i].size | mb0cf[i].reg);
+ mtsdram(SDRAM0_CFG0, CONFIG_SYS_SDRAM0_CFG0);
udelay(10000);
/*
*/
if (get_ram_size((long *)mb0cf[i].size, mb0cf[i].size)
!= mb0cf[i].size) {
- mtsdram(mem_cfg0, 0);
- mtsdram(mem_b1cr, 0);
- mtsdram(mem_cfg0, CONFIG_SYS_SDRAM0_CFG0);
+ mtsdram(SDRAM0_CFG0, 0);
+ mtsdram(SDRAM0_B1CR, 0);
+ mtsdram(SDRAM0_CFG0, CONFIG_SYS_SDRAM0_CFG0);
udelay(10000);
} else {
/*
* SDRAM Controller
*/
-/*
- * XXX - ToDo: Revisit file to change all these lower case defines into
- * upper case. Also needs to be done in the controller setup code too
- * of course. sr, 2008-06-02
- */
#ifndef CONFIG_405EP
-#define mem_besra 0x00 /* bus error syndrome reg a */
-#define mem_besrsa 0x04 /* bus error syndrome reg set a */
-#define mem_besrb 0x08 /* bus error syndrome reg b */
-#define mem_besrsb 0x0c /* bus error syndrome reg set b */
-#define mem_bear 0x10 /* bus error address reg */
+#define SDRAM0_BESR0 0x00 /* bus error syndrome reg a */
+#define SDRAM0_BESRS0 0x04 /* bus error syndrome reg set a */
+#define SDRAM0_BESR1 0x08 /* bus error syndrome reg b */
+#define SDRAM0_BESRS1 0x0c /* bus error syndrome reg set b */
+#define SDRAM0_BEAR 0x10 /* bus error address reg */
#endif
-#define mem_mcopt1 0x20 /* memory controller options 1 */
-#define mem_status 0x24 /* memory status */
-#define mem_rtr 0x30 /* refresh timer reg */
-#define mem_pmit 0x34 /* power management idle timer */
-#define mem_mb0cf 0x40 /* memory bank 0 configuration */
-#define mem_mb1cf 0x44 /* memory bank 1 configuration */
+#define SDRAM0_CFG 0x20 /* memory controller options 1 */
+#define SDRAM0_STATUS 0x24 /* memory status */
+#define SDRAM0_RTR 0x30 /* refresh timer reg */
+#define SDRAM0_PMIT 0x34 /* power management idle timer */
+#define SDRAM0_B0CR 0x40 /* memory bank 0 configuration */
+#define SDRAM0_B1CR 0x44 /* memory bank 1 configuration */
#ifndef CONFIG_405EP
-#define mem_mb2cf 0x48 /* memory bank 2 configuration */
-#define mem_mb3cf 0x4c /* memory bank 3 configuration */
+#define SDRAM0_B2CR 0x48 /* memory bank 2 configuration */
+#define SDRAM0_B3CR 0x4c /* memory bank 3 configuration */
#endif
-#define mem_sdtr1 0x80 /* timing reg 1 */
+#define SDRAM0_TR 0x80 /* timing reg 1 */
#ifndef CONFIG_405EP
-#define mem_ecccf 0x94 /* ECC configuration */
-#define mem_eccerr 0x98 /* ECC error status */
+#define SDRAM0_ECCCFG 0x94 /* ECC configuration */
+#define SDRAM0_ECCESR 0x98 /* ECC error status */
#endif
#endif /* CONFIG_SDRAM_PPC4xx_IBM_SDRAM */
#define SDRAM_CFG0 0x20 /* memory controller options 0 */
#define SDRAM_CFG1 0x21 /* memory controller options 1 */
-/*
- * XXX - ToDo: Revisit file to change all these lower case defines into
- * upper case. Also needs to be done in the controller setup code too
- * of course. sr, 2008-06-02
- */
-#define mem_besr0_clr 0x0000 /* bus error status reg 0 (clr) */
-#define mem_besr0_set 0x0004 /* bus error status reg 0 (set) */
-#define mem_besr1_clr 0x0008 /* bus error status reg 1 (clr) */
-#define mem_besr1_set 0x000c /* bus error status reg 1 (set) */
-#define mem_bear 0x0010 /* bus error address reg */
-#define mem_mirq_clr 0x0011 /* bus master interrupt (clr) */
-#define mem_mirq_set 0x0012 /* bus master interrupt (set) */
-#define mem_slio 0x0018 /* ddr sdram slave interface options */
-#define mem_cfg0 0x0020 /* ddr sdram options 0 */
-#define mem_cfg1 0x0021 /* ddr sdram options 1 */
-#define mem_devopt 0x0022 /* ddr sdram device options */
-#define mem_mcsts 0x0024 /* memory controller status */
-#define mem_rtr 0x0030 /* refresh timer register */
-#define mem_pmit 0x0034 /* power management idle timer */
-#define mem_uabba 0x0038 /* plb UABus base address */
-#define mem_b0cr 0x0040 /* ddr sdram bank 0 configuration */
-#define mem_b1cr 0x0044 /* ddr sdram bank 1 configuration */
-#define mem_b2cr 0x0048 /* ddr sdram bank 2 configuration */
-#define mem_b3cr 0x004c /* ddr sdram bank 3 configuration */
-#define mem_tr0 0x0080 /* sdram timing register 0 */
-#define mem_tr1 0x0081 /* sdram timing register 1 */
-#define mem_clktr 0x0082 /* ddr clock timing register */
-#define mem_wddctr 0x0083 /* write data/dm/dqs clock timing reg */
-#define mem_dlycal 0x0084 /* delay line calibration register */
-#define mem_eccesr 0x0098 /* ECC error status */
+#define SDRAM0_BEAR 0x0010 /* bus error address reg */
+#define SDRAM0_SLIO 0x0018 /* ddr sdram slave interface options */
+#define SDRAM0_CFG0 0x0020 /* ddr sdram options 0 */
+#define SDRAM0_CFG1 0x0021 /* ddr sdram options 1 */
+#define SDRAM0_DEVOPT 0x0022 /* ddr sdram device options */
+#define SDRAM0_MCSTS 0x0024 /* memory controller status */
+#define SDRAM0_RTR 0x0030 /* refresh timer register */
+#define SDRAM0_PMIT 0x0034 /* power management idle timer */
+#define SDRAM0_UABBA 0x0038 /* plb UABus base address */
+#define SDRAM0_B0CR 0x0040 /* ddr sdram bank 0 configuration */
+#define SDRAM0_B1CR 0x0044 /* ddr sdram bank 1 configuration */
+#define SDRAM0_B2CR 0x0048 /* ddr sdram bank 2 configuration */
+#define SDRAM0_B3CR 0x004c /* ddr sdram bank 3 configuration */
+#define SDRAM0_TR0 0x0080 /* sdram timing register 0 */
+#define SDRAM0_TR1 0x0081 /* sdram timing register 1 */
+#define SDRAM0_CLKTR 0x0082 /* ddr clock timing register */
+#define SDRAM0_WDDCTR 0x0083 /* write data/dm/dqs clock timing reg */
+#define SDRAM0_DLYCAL 0x0084 /* delay line calibration register */
+#define SDRAM0_ECCESR 0x0098 /* ECC error status */
/*
* Memory Controller Options 0
u32 val;
do {
- mfsdram(mem_mcsts, val);
+ mfsdram(SDRAM0_MCSTS, val);
} while (!(val & 0x80000000));
}
/*
* Disable memory controller.
*/
- mtsdram(mem_cfg0, 0x00000000);
+ mtsdram(SDRAM0_CFG0, 0x00000000);
/*
* Setup some default
*/
- mtsdram(mem_uabba, 0x00000000); /* ubba=0 (default) */
- mtsdram(mem_slio, 0x00000000); /* rdre=0 wrre=0 rarw=0 */
- mtsdram(mem_devopt, 0x00000000); /* dll=0 ds=0 (normal) */
- mtsdram(mem_wddctr, 0x00000000); /* wrcp=0 dcd=0 */
- mtsdram(mem_clktr, 0x40000000); /* clkp=1 (90 deg wr) dcdt=0 */
+ mtsdram(SDRAM0_UABBA, 0x00000000); /* ubba=0 (default) */
+ mtsdram(SDRAM0_SLIO, 0x00000000); /* rdre=0 wrre=0 rarw=0 */
+ mtsdram(SDRAM0_DEVOPT, 0x00000000); /* dll=0 ds=0 (normal) */
+ mtsdram(SDRAM0_WDDCTR, 0x00000000); /* wrcp=0 dcd=0 */
+ mtsdram(SDRAM0_CLKTR, 0x40000000); /* clkp=1 (90 deg wr) dcdt=0 */
/*
* Following for CAS Latency = 2.5 @ 133 MHz PLB
*/
- mtsdram(mem_b0cr, 0x00082001);
- mtsdram(mem_tr0, 0x41094012);
- mtsdram(mem_tr1, 0x8080083d); /* SS=T2 SL=STAGE 3 CD=1 CT=0x00*/
- mtsdram(mem_rtr, 0x04100000); /* Interval 7.8µs @ 133MHz PLB */
- mtsdram(mem_cfg1, 0x00000000); /* Self-refresh exit, disable PM*/
+ mtsdram(SDRAM0_B0CR, 0x00082001);
+ mtsdram(SDRAM0_TR0, 0x41094012);
+ mtsdram(SDRAM0_TR1, 0x8080083d); /* SS=T2 SL=STAGE 3 CD=1 CT=0x00*/
+ mtsdram(SDRAM0_RTR, 0x04100000); /* Interval 7.8µs @ 133MHz PLB */
+ mtsdram(SDRAM0_CFG1, 0x00000000); /* Self-refresh exit, disable PM*/
/*
* Enable the controller, then wait for DCEN to complete
*/
- mtsdram(mem_cfg0, 0x80000000); /* DCEN=1, PMUD=0*/
+ mtsdram(SDRAM0_CFG0, 0x80000000); /* DCEN=1, PMUD=0*/
wait_init_complete();
return CONFIG_SYS_MBYTES_SDRAM << 20;
projects / u-boot.git / commitdiff
