#if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R)
+#define MII_MARVELL_PHY_PAGE 22
+
#define MV88E1116_LED_FCTRL_REG 10
#define MV88E1116_CPRSP_CR3_REG 21
#define MV88E1116_MAC_CTRL_REG 21
-#define MV88E1116_PGADR_REG 22
#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)
#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)
* Enable RGMII delay on Tx and Rx for CPU port
* Ref: sec 4.7.2 of chip datasheet
*/
- miiphy_write(name, phyaddr, MV88E1116_PGADR_REG, 2);
+ miiphy_write(name, phyaddr, MII_MARVELL_PHY_PAGE, 2);
miiphy_read(name, phyaddr, MV88E1116_MAC_CTRL_REG, ®);
reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
miiphy_write(name, phyaddr, MV88E1116_MAC_CTRL_REG, reg);
- miiphy_write(name, phyaddr, MV88E1116_PGADR_REG, 0);
+ miiphy_write(name, phyaddr, MII_MARVELL_PHY_PAGE, 0);
if (miiphy_reset(name, phyaddr) == 0)
printf("88E1116 Initialized on %s\n", name);
}
+
+void mv_phy_88e1318_init(const char *name, u16 phyaddr)
+{
+ u16 reg;
+
+ if (miiphy_set_current_dev(name))
+ return;
+
+ /*
+ * Set control mode 4 for LED[0].
+ */
+ miiphy_write(name, phyaddr, MII_MARVELL_PHY_PAGE, 3);
+ miiphy_read(name, phyaddr, 16, ®);
+ reg |= 0xf;
+ miiphy_write(name, phyaddr, 16, reg);
+
+ /*
+ * Enable RGMII delay on Tx and Rx for CPU port
+ * Ref: sec 4.7.2 of chip datasheet
+ */
+ miiphy_write(name, phyaddr, MII_MARVELL_PHY_PAGE, 2);
+ miiphy_read(name, phyaddr, MV88E1116_MAC_CTRL_REG, ®);
+ reg |= (MV88E1116_RGMII_TXTM_CTRL | MV88E1116_RGMII_RXTM_CTRL);
+ miiphy_write(name, phyaddr, MV88E1116_MAC_CTRL_REG, reg);
+ miiphy_write(name, phyaddr, MII_MARVELL_PHY_PAGE, 0);
+
+ if (miiphy_reset(name, phyaddr) == 0)
+ printf("88E1318 Initialized on %s\n", name);
+}
#endif /* CONFIG_CMD_NET && CONFIG_RESET_PHY_R */
#if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR)
--- /dev/null
+#
+# Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
+#
+# Based on Kirkwood support:
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# Refer docs/README.kwimage for more details about how-to configure
+# and create kirkwood boot image
+#
+
+# Boot Media configurations
+BOOT_FROM spi # Boot from SPI flash
+
+# SOC registers configuration using bootrom header extension
+# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
+
+# Configure RGMII-0 interface pad voltage to 1.8V
+DATA 0xFFD100e0 0x1B1B1B9B
+
+#Dram initalization for SINGLE x16 CL=5 @ 400MHz
+DATA 0xFFD01400 0x43000618 # DDR Configuration register
+# bit13-0: 0xa00 (2560 DDR2 clks refresh rate)
+# bit23-14: zero
+# bit24: 1= enable exit self refresh mode on DDR access
+# bit25: 1 required
+# bit29-26: zero
+# bit31-30: 01
+
+DATA 0xFFD01404 0x34143000 # DDR Controller Control Low
+# bit 4: 0=addr/cmd in smame cycle
+# bit 5: 0=clk is driven during self refresh, we don't care for APX
+# bit 6: 0=use recommended falling edge of clk for addr/cmd
+# bit14: 0=input buffer always powered up
+# bit18: 1=cpu lock transaction enabled
+# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
+# bit27-24: 8= CL+3, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
+# bit30-28: 3 required
+# bit31: 0=no additional STARTBURST delay
+
+DATA 0xFFD01408 0x11012228 # DDR Timing (Low) (active cycles value +1)
+# bit7-4: TRCD
+# bit11- 8: TRP
+# bit15-12: TWR
+# bit19-16: TWTR
+# bit20: TRAS msb
+# bit23-21: 0x0
+# bit27-24: TRRD
+# bit31-28: TRTP
+
+DATA 0xFFD0140C 0x00000A19 # DDR Timing (High)
+# bit6-0: TRFC
+# bit8-7: TR2R
+# bit10-9: TR2W
+# bit12-11: TW2W
+# bit31-13: zero required
+
+DATA 0xFFD01410 0x0000DDDD # DDR Address Control
+# bit1-0: 00, Cs0width=x8
+# bit3-2: 10, Cs0size=512Mb
+# bit5-4: 00, Cs2width=nonexistent
+# bit7-6: 00, Cs1size =nonexistent
+# bit9-8: 00, Cs2width=nonexistent
+# bit11-10: 00, Cs2size =nonexistent
+# bit13-12: 00, Cs3width=nonexistent
+# bit15-14: 00, Cs3size =nonexistent
+# bit16: 0, Cs0AddrSel
+# bit17: 0, Cs1AddrSel
+# bit18: 0, Cs2AddrSel
+# bit19: 0, Cs3AddrSel
+# bit31-20: 0 required
+
+DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
+# bit0: 0, OpenPage enabled
+# bit31-1: 0 required
+
+DATA 0xFFD01418 0x00000000 # DDR Operation
+# bit3-0: 0x0, DDR cmd
+# bit31-4: 0 required
+
+DATA 0xFFD0141C 0x00000632 # DDR Mode
+# bit2-0: 2, BurstLen=2 required
+# bit3: 0, BurstType=0 required
+# bit6-4: 4, CL=5
+# bit7: 0, TestMode=0 normal
+# bit8: 0, DLL reset=0 normal
+# bit11-9: 6, auto-precharge write recovery ????????????
+# bit12: 0, PD must be zero
+# bit31-13: 0 required
+
+DATA 0xFFD01420 0x00000004 # DDR Extended Mode
+# bit0: 0, DDR DLL enabled
+# bit1: 1, DDR drive strenght reduced
+# bit2: 1, DDR ODT control lsd enabled
+# bit5-3: 000, required
+# bit6: 1, DDR ODT control msb, enabled
+# bit9-7: 000, required
+# bit10: 0, differential DQS enabled
+# bit11: 0, required
+# bit12: 0, DDR output buffer enabled
+# bit31-13: 0 required
+
+DATA 0xFFD01424 0x0000F07F # DDR Controller Control High
+# bit2-0: 111, required
+# bit3 : 1 , MBUS Burst Chop disabled
+# bit6-4: 111, required
+# bit7 : 1 , D2P Latency enabled
+# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
+# bit9 : 0 , no half clock cycle addition to dataout
+# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
+# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
+# bit15-12: 1111 required
+# bit31-16: 0 required
+
+DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
+DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
+
+DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
+DATA 0xFFD01504 0x07FFFFF1 # CS[0]n Size
+# bit0: 1, Window enabled
+# bit1: 0, Write Protect disabled
+# bit3-2: 00, CS0 hit selected
+# bit23-4: ones, required
+# bit31-24: 0x07, Size (i.e. 128MB)
+
+DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled
+DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
+DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
+
+DATA 0xFFD01494 0x00010000 # DDR ODT Control (Low)
+# bit3-0: 1, ODT0Rd, MODT[0] asserted during read from DRAM CS0
+# bit19-16:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0
+
+DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
+# bit1-0: 00, ODT0 controlled by ODT Control (low) register above
+# bit3-2: 01, ODT1 active NEVER!
+# bit31-4: zero, required
+
+DATA 0xFFD0149C 0x0000E40F # CPU ODT Control
+# bit3-0: 1, ODT0Rd, Internal ODT asserted during read from DRAM bank0
+# bit7-4: 1, ODT0Wr, Internal ODT asserted during write to DRAM bank0
+# bit11-10:1, DQ_ODTSel. ODT select turned on
+
+DATA 0xFFD01480 0x00000001 # DDR Initialization Control
+#bit0=1, enable DDR init upon this register write
+
+# End of Header extension
+DATA 0x0 0x0
#elif defined(CONFIG_NETSPACE_V2)
#define CONFIG_MACH_TYPE MACH_TYPE_NETSPACE_V2
#define CONFIG_IDENT_STRING " NS v2"
+#elif defined(CONFIG_NETSPACE_LITE_V2)
+#define MACH_TYPE_NETSPACE_LITE_V2 2983 /* missing in mach-types.h */
+#define CONFIG_MACH_TYPE MACH_TYPE_NETSPACE_LITE_V2
+#define CONFIG_IDENT_STRING " NS v2 Lite"
+#elif defined(CONFIG_NETSPACE_MINI_V2)
+#define MACH_TYPE_NETSPACE_MINI_V2 2831 /* missing in mach-types.h */
+#define CONFIG_MACH_TYPE MACH_TYPE_NETSPACE_MINI_V2
+#define CONFIG_IDENT_STRING " NS v2 Mini"
#elif defined(CONFIG_NETSPACE_MAX_V2)
#define CONFIG_MACH_TYPE MACH_TYPE_NETSPACE_MAX_V2
#define CONFIG_IDENT_STRING " NS Max v2"
* High Level Configuration Options (easy to change)
*/
#define CONFIG_FEROCEON_88FR131 /* CPU Core subversion */
-#define CONFIG_KIRKWOOD /* SOC Family Name */
-#define CONFIG_KW88F6281 /* SOC Name */
+#define CONFIG_KIRKWOOD /* SoC Family Name */
+/* SoC name */
+#if defined(CONFIG_NETSPACE_LITE_V2) || defined(CONFIG_NETSPACE_MINI_V2)
+#define CONFIG_KW88F6192
+#else
+#define CONFIG_KW88F6281
+#endif
#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
/*
#define CONFIG_CMD_SF
#define CONFIG_CMD_I2C
#define CONFIG_CMD_IDE
+#ifndef CONFIG_NETSPACE_MINI_V2 /* No USB ports on Network Space v2 Mini */
#define CONFIG_CMD_USB
+#endif
/*
* Core clock definition
*/
#define CONFIG_NR_DRAM_BANKS 1
-#ifdef CONFIG_INETSPACE_V2
-/* Different SDRAM configuration and size for Internet Space v2 */
+/*
+ * Different SDRAM configuration and size for some of the boards derived
+ * from the Network Space v2
+ */
+#if defined(CONFIG_INETSPACE_V2)
#define CONFIG_SYS_KWD_CONFIG $(SRCTREE)/$(CONFIG_BOARDDIR)/kwbimage-is2.cfg
+#elif defined(CONFIG_NETSPACE_LITE_V2) || defined(CONFIG_NETSPACE_MINI_V2)
+#define CONFIG_SYS_KWD_CONFIG $(SRCTREE)/$(CONFIG_BOARDDIR)/kwbimage-ns2l.cfg
#endif
/*
projects / u-boot.git / commitdiff
