#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "Xunlong Orange Pi Zero";
aliases {
serial0 = &uart0;
/* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
+ ethernet0 = &emac;
ethernet1 = &xr819;
};
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>;
+ post-power-on-delay-ms = <200>;
};
};
+&ehci0 {
+ status = "okay";
+};
+
&ehci1 {
status = "okay";
};
&mmc0 {
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
- cd-inverted;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
status = "okay";
};
};
};
+&ohci0 {
+ status = "okay";
+};
+
&ohci1 {
status = "okay";
};
+&spi0 {
+ /* Disable SPI NOR by default: it optional on Orange Pi Zero boards */
+ status = "disabled";
+
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "mxicy,mx25l1606e", "winbond,w25q128";
+ reg = <0>;
+ spi-max-frequency = <40000000>;
+ };
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "disabled";
+};
+
+&usb_otg {
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
&usbphy {
- /* USB VBUS is always on */
+ /*
+ * USB Type-A port VBUS is always on. However, MicroUSB VBUS can only
+ * power up the board; when it's used as OTG port, this VBUS is
+ * always off even if the board is powered via GPIO pins.
+ */
status = "okay";
+ usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
};
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "Banana Pi BPI-M2-Plus";
compatible = "sinovoip,bpi-m2-plus", "allwinner,sun8i-h3";
aliases {
+ ethernet0 = &emac;
serial0 = &uart0;
serial1 = &uart1;
};
stdout-path = "serial0:115200n8";
};
+ connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
- pinctrl-0 = <&pwr_led_bpi_m2p>;
pwr_led {
label = "bananapi-m2-plus:red:pwr";
gpio_keys {
compatible = "gpio-keys";
pinctrl-names = "default";
- pinctrl-0 = <&sw_r_bpi_m2p>;
sw4 {
label = "power";
};
};
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ enable-active-high;
+ gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
+ };
+
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
pinctrl-names = "default";
- pinctrl-0 = <&wifi_en_bpi_m2p>;
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
};
};
+&de {
+ status = "okay";
+};
+
&ehci0 {
status = "okay";
};
status = "okay";
};
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_rgmii_pins>;
+ phy-supply = <®_gmac_3v3>;
+ phy-handle = <&ext_rgmii_phy>;
+ phy-mode = "rgmii";
+
+ status = "okay";
+};
+
+&external_mdio {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
&ir {
pinctrl-names = "default";
pinctrl-0 = <&ir_pins_a>;
&mmc0 {
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
- cd-inverted;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
status = "okay";
};
non-removable;
status = "okay";
- brcmf: bcrmf@1 {
+ brcmf: wifi@1 {
reg = <1>;
compatible = "brcm,bcm4329-fmac";
interrupt-parent = <&pio>;
status = "okay";
};
-&r_pio {
- pwr_led_bpi_m2p: led_pins@0 {
- allwinner,pins = "PL10";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- sw_r_bpi_m2p: key_pins@0 {
- allwinner,pins = "PL3";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- wifi_en_bpi_m2p: wifi_en_pin {
- allwinner,pins = "PL7";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
+®_usb0_vbus {
+ gpio = <&pio 3 11 GPIO_ACTIVE_HIGH>; /* PD11 */
+ status = "okay";
};
&uart0 {
};
&usbphy {
- /* USB VBUS is on as long as VCC-IO is on */
+ usb0_id_det-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+ usb0_vbus-supply = <®_usb0_vbus>;
+ /* USB host VBUS is on as long as VCC-IO is on */
status = "okay";
};
-// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Copyright (C) 2017 Chen-Yu Tsai <wens@csie.org>
+ *
+ * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
*/
/dts-v1/;
/ {
model = "FriendlyArm NanoPi M1 Plus";
compatible = "friendlyarm,nanopi-m1-plus", "allwinner,sun8i-h3";
+
+ aliases {
+ serial1 = &uart3;
+ ethernet0 = &emac;
+ ethernet1 = &sdio_wifi;
+ };
+
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ enable-active-high;
+ gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+ };
};
&ehci1 {
status = "okay";
};
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_rgmii_pins>;
+ phy-supply = <®_gmac_3v3>;
+ phy-handle = <&ext_rgmii_phy>;
+ phy-mode = "rgmii";
+
+ status = "okay";
+};
+
+&external_mdio {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <7>;
+ };
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
+&mmc1 {
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc3v3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ sdio_wifi: sdio_wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&pio>;
+ interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
+ interrupt-names = "host-wake";
+ };
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_pins>;
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc3v3>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
&ohci1 {
status = "okay";
};
&ohci2 {
status = "okay";
};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>, <&uart3_rts_cts_pins>;
+ status = "okay";
+};
/ {
model = "FriendlyArm NanoPi M1";
compatible = "friendlyarm,nanopi-m1", "allwinner,sun8i-h3";
+
+ aliases {
+ ethernet0 = &emac;
+ };
+
+ connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+};
+
+&de {
+ status = "okay";
};
&ehci1 {
status = "okay";
};
+&emac {
+ phy-handle = <&int_mii_phy>;
+ phy-mode = "mii";
+ allwinner,leds-active-low;
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
&ohci1 {
status = "okay";
};
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "FriendlyARM NanoPi NEO Air";
gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>; /* PA10 */
};
};
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+ };
};
&mmc0 {
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
- cd-inverted;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
status = "okay";
};
+&mmc1 {
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc3v3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ brcmf: bcrmf@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&pio>;
+ interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
+ interrupt-names = "host-wake";
+ };
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
compatible = "friendlyarm,nanopi-neo", "allwinner,sun8i-h3";
};
+&ehci0 {
+ status = "okay";
+};
+
&emac {
phy-handle = <&int_mii_phy>;
phy-mode = "mii";
allwinner,leds-active-low;
status = "okay";
};
+
+&ohci0 {
+ status = "okay";
+};
+
+&usb_otg {
+ status = "okay";
+ dr_mode = "peripheral";
+};
+
+&usbphy {
+ usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+};
pinctrl-names = "default";
pinctrl-0 = <&sw_r_npi>;
- k1@0 {
+ k1 {
label = "k1";
linux,code = <KEY_POWER>;
gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
&mmc0 {
bus-width = <4>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
- cd-inverted;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
status = "okay";
vmmc-supply = <®_vcc3v3>;
};
};
&pio {
- leds_npi: led_pins@0 {
+ leds_npi: led_pins {
pins = "PA10";
function = "gpio_out";
};
};
&r_pio {
- leds_r_npi: led_pins@0 {
+ leds_r_npi: led_pins {
pins = "PL10";
function = "gpio_out";
};
- sw_r_npi: key_pins@0 {
+ sw_r_npi: key_pins {
pins = "PL3";
function = "gpio_in";
};
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "Xunlong Orange Pi 2";
stdout-path = "serial0:115200n8";
};
+ connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
};
};
+&codec {
+ allwinner,pa-gpios = <&pio 0 16 GPIO_ACTIVE_HIGH>; /* PA16 */
+ allwinner,audio-routing =
+ "Speaker", "LINEOUT",
+ "MIC1", "Mic",
+ "Mic", "MBIAS";
+ status = "okay";
+};
+
+&de {
+ status = "okay";
+};
+
&ehci1 {
status = "okay";
};
status = "okay";
};
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
&ir {
pinctrl-names = "default";
pinctrl-0 = <&ir_pins_a>;
&mmc0 {
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
- cd-inverted;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
status = "okay";
};
};
&pio {
- leds_opc: led_pins@0 {
- allwinner,pins = "PA15";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ leds_opc: led_pins {
+ pins = "PA15";
+ function = "gpio_out";
};
};
&r_pio {
- leds_r_opc: led_pins@0 {
- allwinner,pins = "PL10";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ leds_r_opc: led_pins {
+ pins = "PL10";
+ function = "gpio_out";
};
- sw_r_opc: key_pins@0 {
- allwinner,pins = "PL3", "PL4";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ sw_r_opc: key_pins {
+ pins = "PL3", "PL4";
+ function = "gpio_in";
};
- wifi_pwrseq_pin_orangepi: wifi_pwrseq_pin@0 {
- allwinner,pins = "PL7";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ wifi_pwrseq_pin_orangepi: wifi_pwrseq_pin {
+ pins = "PL7";
+ function = "gpio_out";
};
};
status = "okay";
};
-&usb1_vbus_pin_a {
- allwinner,pins = "PG13";
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "disabled";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+ status = "disabled";
};
&usbphy {
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "Xunlong Orange Pi Lite";
stdout-path = "serial0:115200n8";
};
+ connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
};
};
+&de {
+ status = "okay";
+};
+
&ehci1 {
status = "okay";
};
status = "okay";
};
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
&ir {
pinctrl-names = "default";
pinctrl-0 = <&ir_pins_a>;
&mmc0 {
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
- cd-inverted;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
status = "okay";
};
};
&pio {
- leds_opc: led_pins@0 {
- allwinner,pins = "PA15";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ leds_opc: led_pins {
+ pins = "PA15";
+ function = "gpio_out";
};
};
&r_pio {
- leds_r_opc: led_pins@0 {
- allwinner,pins = "PL10";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ leds_r_opc: led_pins {
+ pins = "PL10";
+ function = "gpio_out";
};
- sw_r_opc: key_pins@0 {
- allwinner,pins = "PL3";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ sw_r_opc: key_pins {
+ pins = "PL3";
+ function = "gpio_in";
};
};
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "Xunlong Orange Pi One";
stdout-path = "serial0:115200n8";
};
+ connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
};
};
+
+ reg_vdd_cpux: vdd-cpux-regulator {
+ compatible = "regulator-gpio";
+ regulator-name = "vdd-cpux";
+ regulator-type = "voltage";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-ramp-delay = <50>; /* 4ms */
+
+ gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+ enable-active-high;
+ gpios-states = <0x1>;
+ states = <1100000 0x0
+ 1300000 0x1>;
+ };
+};
+
+&cpu0 {
+ cpu-supply = <®_vdd_cpux>;
+};
+
+&de {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
};
&ehci1 {
status = "okay";
};
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
&mmc0 {
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
- cd-inverted;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ status = "okay";
+};
+
+&ohci0 {
status = "okay";
};
};
&pio {
- leds_opc: led_pins@0 {
- allwinner,pins = "PA15";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ leds_opc: led_pins {
+ pins = "PA15";
+ function = "gpio_out";
};
};
&r_pio {
- leds_r_opc: led_pins@0 {
- allwinner,pins = "PL10";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ leds_r_opc: led_pins {
+ pins = "PL10";
+ function = "gpio_out";
};
- sw_r_opc: key_pins@0 {
- allwinner,pins = "PL3";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ sw_r_opc: key_pins {
+ pins = "PL3";
+ function = "gpio_in";
};
};
+®_usb0_vbus {
+ gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
+ status = "okay";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "disabled";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+ status = "disabled";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
&usbphy {
- /* USB VBUS is always on */
+ /* USB Type-A port's VBUS is always on */
+ usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+ usb0_vbus-supply = <®_usb0_vbus>;
status = "okay";
};
};
};
+&emac {
+ /* LEDs changed to active high on the plus */
+ /delete-property/ allwinner,leds-active-low;
+};
+
&mmc1 {
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
&mmc2_8bit_pins {
/* Increase drive strength for DDR modes */
- allwinner,drive = <SUN4I_PINCTRL_40_MA>;
+ drive-strength = <40>;
/* eMMC is missing pull-ups */
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ bias-pull-up;
};
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "Xunlong Orange Pi PC";
stdout-path = "serial0:115200n8";
};
+ connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
};
};
+&codec {
+ allwinner,audio-routing =
+ "Line Out", "LINEOUT",
+ "MIC1", "Mic",
+ "Mic", "MBIAS";
+ status = "okay";
+};
+
+&de {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <®_vdd_cpux>;
+};
+
+&ehci0 {
+ status = "okay";
+};
+
&ehci1 {
status = "okay";
};
status = "okay";
};
+&emac {
+ phy-handle = <&int_mii_phy>;
+ phy-mode = "mii";
+ allwinner,leds-active-low;
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
&ir {
pinctrl-names = "default";
pinctrl-0 = <&ir_pins_a>;
&mmc0 {
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
- cd-inverted;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ status = "okay";
+};
+
+&ohci0 {
status = "okay";
};
};
&pio {
- leds_opc: led_pins@0 {
- allwinner,pins = "PA15";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ leds_opc: led_pins {
+ pins = "PA15";
+ function = "gpio_out";
+ };
+};
+
+&r_i2c {
+ status = "okay";
+
+ reg_vdd_cpux: regulator@65 {
+ compatible = "silergy,sy8106a";
+ reg = <0x65>;
+ regulator-name = "vdd-cpux";
+ silergy,fixed-microvolt = <1200000>;
+ /*
+ * The datasheet uses 1.1V as the minimum value of VDD-CPUX,
+ * however both the Armbian DVFS table and the official one
+ * have operating points with voltage under 1.1V, and both
+ * DVFS table are known to work properly at the lowest
+ * operating point.
+ *
+ * Use 1.0V as the minimum voltage instead.
+ */
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ regulator-always-on;
};
};
&r_pio {
- leds_r_opc: led_pins@0 {
- allwinner,pins = "PL10";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ leds_r_opc: led_pins {
+ pins = "PL10";
+ function = "gpio_out";
};
- sw_r_opc: key_pins@0 {
- allwinner,pins = "PL3";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ sw_r_opc: key_pins {
+ pins = "PL3";
+ function = "gpio_in";
};
};
+®_usb0_vbus {
+ gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
+ status = "okay";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
-&usbphy {
- /* USB VBUS is always on */
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "disabled";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+ status = "disabled";
+};
+
+&usb_otg {
+ dr_mode = "otg";
status = "okay";
};
-&emac {
- phy-handle = <&int_mii_phy>;
- phy-mode = "mii";
- allwinner,leds-active-low;
+&usbphy {
+ usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+ usb0_vbus-supply = <®_usb0_vbus>;
+ /* VBUS on USB host ports are always on */
status = "okay";
};
model = "Xunlong Orange Pi Plus / Plus 2";
compatible = "xunlong,orangepi-plus", "allwinner,sun8i-h3";
+ aliases {
+ ethernet0 = &emac;
+ };
+
reg_gmac_3v3: gmac-3v3 {
compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&gmac_power_pin_orangepi>;
regulator-name = "gmac-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
&emac {
- /* The Orange Pi Plus uses an external phy */
pinctrl-names = "default";
pinctrl-0 = <&emac_rgmii_pins>;
phy-supply = <®_gmac_3v3>;
+ phy-handle = <&ext_rgmii_phy>;
phy-mode = "rgmii";
+
+ status = "okay";
};
&external_mdio {
&mmc2_8bit_pins {
/* Increase drive strength for DDR modes */
- allwinner,drive = <SUN4I_PINCTRL_40_MA>;
+ drive-strength = <40>;
/* eMMC is missing pull-ups */
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ bias-pull-up;
};
&pio {
- gmac_power_pin_orangepi: gmac_power_pin@0 {
- allwinner,pins = "PD6";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- usb3_vbus_pin_a: usb3_vbus_pin@0 {
- allwinner,pins = "PG11";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ usb3_vbus_pin_a: usb3_vbus_pin {
+ pins = "PG11";
+ function = "gpio_out";
};
};
reg_gmac_3v3: gmac-3v3 {
compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&gmac_power_pin_orangepi>;
regulator-name = "gmac-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
startup-delay-us = <100000>;
enable-active-high;
- gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
+ gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */
};
};
&emac {
- /* The Orange Pi Plus 2E uses an external gbit phy */
pinctrl-names = "default";
pinctrl-0 = <&emac_rgmii_pins>;
phy-supply = <®_gmac_3v3>;
phy-handle = <&ext_rgmii_phy>;
phy-mode = "rgmii";
+ status = "okay";
};
&external_mdio {
reg = <1>;
};
};
-
-&pio {
- gmac_power_pin_orangepi: gmac_power_pin@0 {
- allwinner,pins = "PD6";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-};
projects / u-boot.git / commitdiff
