Simon Glass [Wed, 7 Aug 2024 22:47:28 +0000 (16:47 -0600)]
upl: Add support for writing a upl handoff
Universal Payload provides a standard way of handing off control between
two firmware phases. Add support for writing the handoff information from
a structure.
Simon Glass [Wed, 7 Aug 2024 22:47:27 +0000 (16:47 -0600)]
upl: Add support for reading a upl handoff
Universal Payload provides a standard way of handing off control between
two firmware phases. Add support for reading the handoff information into
a structure.
Simon Glass [Wed, 7 Aug 2024 22:47:26 +0000 (16:47 -0600)]
sandbox: Set up global_data earlier
It is possible for U-Boot functions such as printf() to be called
within state_init(). This can end up checking gd->flags (e.g. in putc())
before global_data is set up.
Move the setup earlier to avoid this. This fixes the suppression of some
debug output in memory allocation (when enabled).
Simon Glass [Wed, 7 Aug 2024 22:47:24 +0000 (16:47 -0600)]
sandbox: Return error code from read/write/seek
The existing API for these functions is different from the rest of
U-Boot, in that any error code must be obtained from the errno variable
on failure. This variable is part of the C library, so accessing it
outside of the special 'sandbox' shim-functions is not ideal.
Adjust the API to return an error code, to avoid this. Update existing
uses to check for any negative value, rather than just -1.
Simon Glass [Wed, 7 Aug 2024 22:47:23 +0000 (16:47 -0600)]
sandbox: fdt: Avoid overwriting an existing fdt
Since the removal of OF_HOSTFILE logic in board_fdt_blob_setup(), the
logic for obtaining the DT is handled in the OF_BOARD option. If a
devicetree comes from a bloblist it is immediately overwritten by this
function.
Fix this by skipping the function if a devicetree is already present.
This is sort-of a fix for e7fb7896 ("sandbox: Remove OF_HOSTFILE") but
it has only come to light since bloblist was added, so I have not added
a Fixes tag.
Unfortunately it is not possible to report the correct FDT source with
the current code. It might be best to use an error-return code for
board_fdt_blob_setup() so that an error can be reported if the board
does not provide the DT.
Tom Rini [Mon, 5 Aug 2024 18:15:44 +0000 (12:15 -0600)]
Merge patch series "Bug-fixes for a few boards"
Simon Glass <sjg@chromium.org> says:
This series includes fixes to get some rockchip and nvidia boards
working again. It also drops the broken Beaglebone Black config and
provides a devicetree fix for coral (x86).
Simon Glass [Thu, 1 Aug 2024 12:47:23 +0000 (06:47 -0600)]
rockchip: Avoid #ifdefs in RK3399 SPL
The code here is confusing due to large blocks which are #ifdefed out.
Add a function phase_sdram_init() which returns whether SDRAM init
should happen in the current phase, using that as needed to control the
code flow.
This increases code size by about 500 bytes in SPL when the cache is on,
since it must call the rather large rockchip_sdram_size() function.
Simon Glass [Wed, 31 Jul 2024 14:49:05 +0000 (08:49 -0600)]
fdt: Correct condition for bloblist existing
On some boards, the bloblist is created in SPL once SDRAM is ready. It
cannot be accessed until that point, so is not available early in SPL.
Add a condition to avoid a hang in this case.
This fixes a hang in chromebook_coral
Fixes: 70fe2385943 ("fdt: Allow the devicetree to come from a bloblist") Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Raymond Mao <raymond.mao@linaro.org>
Hou Zhiqiang [Thu, 1 Aug 2024 03:59:55 +0000 (11:59 +0800)]
cmd: cpu: add release subcommand
Add a new subcommand 'release' to bring up a core to run baremetal
and RTOS applications.
For example on i.MX8M Plus EVK, release the LAST core to run a RTOS
application, passing the sequence number of the CPU core to release,
here it is 3:
u-boot=> cpu list
0: cpu@0 NXP i.MX8MP Rev1.1 A53 at 1200 MHz at 31C
1: cpu@1 NXP i.MX8MP Rev1.1 A53 at 1200 MHz at 30C
2: cpu@2 NXP i.MX8MP Rev1.1 A53 at 1200 MHz at 31C
3: cpu@3 NXP i.MX8MP Rev1.1 A53 at 1200 MHz at 31C
u-boot=> load mmc 1:2 c0000000 /hello_world.bin
66008 bytes read in 5 ms (12.6 MiB/s)
u-boot=> dcache flush; icache flush
u-boot=> cpu release 3 c0000000
Released CPU core (mpidr: 0x3) to address 0xc0000000
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Hou Zhiqiang [Thu, 1 Aug 2024 03:59:47 +0000 (11:59 +0800)]
cpu: add release_core callback
Add a new callback release_core to the cpu_ops, which is used to
release a CPU core to run baremetal or RTOS application on a SoC
with multiple CPU cores.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Hou Zhiqiang [Thu, 1 Aug 2024 03:59:46 +0000 (11:59 +0800)]
clk: imx8m: register ARM A53 core clock
Register ARM A53 core clock for i.MX 8M Mini, Nano and Plus, preparing
for enabling the 'cpu' command, which depends on this to print CPU core
frequency.
Instead of using the local imx7s-warp devicetree copies from U-Boot,
convert the imx7s-warp board to OF_UPSTREAM so that the upstream
kernel devicetree can be used instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Alexander Dahl [Fri, 3 May 2024 07:20:09 +0000 (09:20 +0200)]
clk: Revise help text for clk_get_parent_rate()
The function returns the rate of the parent clock, the previous text
made no sense at all.
Fixes: 4aa78300a025 ("dm: clk: Define clk_get_parent_rate() for clk operations") Signed-off-by: Alexander Dahl <ada@thorsis.com> Reviewed-by: Sean Anderson <seanga2@gmail.com>
Jan Kiszka [Sat, 9 Mar 2024 12:27:09 +0000 (13:27 +0100)]
clk: Fix error message in clk_get_bulk
Fix a logical inversion of the printed text.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Sean Anderson <seanga2@gmail.com>
Tom Rini [Thu, 1 Aug 2024 21:32:54 +0000 (15:32 -0600)]
Merge patch series "clk: mediatek: add OPs to support OF_UPSTREAM"
Christian Marangi <ansuelsmth@gmail.com> says:
This series doesn't currently change anything and it does add all the
additional OPs to make support of OF_UPSTREAM.
While converting the mt7681/7686/7688/7623/7622 it was notice lots of
discrepancy between the downstream dtsi and the upstream one and the
clock ID between downstream clock ID and upstream clock ID.
Upstream reference clock by names and clock are handled by the
CCF (Common Clock Framework). The same can't be used here as we would
quickly reach the max space allocated before relocation.
The current mediatek clock driver reference all the parents and clocks
with offset from the clk ID related to the different tables.
Discrepancy between clock ID and the order in the clocks table cause
one clock referenced for another or even crash for trying to access
a clock at an offset that doesn't exist.
To handle this and permit use of OF_UPSTREAM, various measure and
changes are done to the mediatek clock driver to support it.
This series have all the generic clock changes. Once this is merged,
series for each SoC will came that will just change files in their
dedicated clock driver. This is to prevent massive patch and to
permit to split series, one for each SoC.
As said at the start, these changes doesn't cause regression and are
just expansion to the current API. Current behaviour is saved in every
possible way (aside from the first 2 patch that fixes latent bugs)
clk: mediatek: add support for GATEs for APMIXED OPs
Add support for GATEs for APMIXED OPs. It's possible that some APMIXED
have also gates on top of PLL. This is the case for mt7622. Add support
for this.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
clk: mediatek: implement MUX_FLAGS and MUX_MIXED_FLAGS macro
Some simple MUX might require flags to specify the parent source.
Implement MUX_FLAGS as a variant of the MUX macro that takes custom
flags as last arg.
Also implement MUX_MIXED_FLAGS for PARENT_MIXED implementation and
MUX_MIXED with no additional flags.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Upstream kernel linux might have a different clock ID order in their
<soc>-clk.h header. This is the case of some clock ID for mt7623 that
upstream use the shared header clk-mt7601.h
This header doesn't have a well distincted order and have factor or mux
in the middle of the CLK ID list. This is problematic with the mtk clock
driver that expect everything well organized in block and apply offset
to reference the clk in the different array.
To solve this problem, implement in the mtk_clk_tree an additional
option .id_offs_map, an array where each CLK ID can be remapped to what
the driver expect permitting to reorganize the clock following the
expected logic of fixed, factor, mux and gates.
Each clock function is updated to tranparently handle this by first
converting the clk ID to the remapped one.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
clk: mediatek: provide common clk init function for infrasys
Provide common clk init function for infrasys that defaults to topckgen
driver if clock-parent is not defined. This is the case for upstream
DTSI that doesn't provide this entry.
This is needed for infracfg driver that will make use of the unified
gates + muxes implementation.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
clk: mediatek: add support for gate clock to reference topckgen clock
Add support for gate clock get_rate to reference topckgen clock for
infracfg-ao implementation.
In infracfg-ao implementation topckgen is on second level of parent with
infracfg in the middle.
To correctly detect this, check the driver of the dev parent and use the
second level parent if it's not mtk_clk_topckgen.
Due to all the dependency, parent tree must be filled before a gate is
used, hence is safe to assume it will be there.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
clk: mediatek: add support for parent mux from different source for topckgen
As done for infracfg, also add support for parent mux from different
source for topckgen. This is needed as upstream linux doesn't use 1/1
factor and use directly the APMIXED clocks.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
clk: mediatek: add support for parent mux from different source
There is a current limitation where parents for a mux can be all declared
as they are from a common source. This is not true as there are some MUX
that can have parent from both infracfg or from topckgen.
To handle this, implement a new flag for the mux, CLK_PARENT_MIXED, and
a new entry for the mux parent_flags.
To use this, CLK_PARENT_MIXED must be used and parent_flags will be used
instead of the parent variable.
Entry in parent_flags are just a struct of ID and flags where it will be
defined where that parent comes from with the usage of
CLK_PARENT_INFRASYS or CLK_PARENT_TOPCKGEN.
This permits to have MUX with parents from infracfg or topckgen.
Notice that with CLK_PARENT_MIXED applied the CLK_BYPASS_XTAL is
ignored.
With CLK_PARENT_MIXED declare CLK_PARENT_XTAL for the relevant parent
instead.
Also alias for the CLK_PARENT macro are provided to better clear their
usage. CLK_PARENT_MIXED require these alias that describe the clk type
to be defined in the clk_tree flags to prevent clk ID clash from
different subsystem that may have equal clk ID.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add support to clk_gate ops to reference the clk ID at an offset by
using the just introduced gates_offs value from the unified muxes +
gates implementation.
Gate clock that doesn't have gates_offs set won't be affected as the
offset will simply be 0 and won't be offset of any value.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
clk: mediatek: add support for gates in clk_tree for infrasys
Add support for gates in clk_tree for infrasys ops.
Infracfg clks can have a sum of gates and muxes, and current solution
handle this by duplicating the driver and split clks for mux and clks
for gates. Upstream linux kernel handle this differently and doesn't
have this distinction.
To be closer to the upstream kernel clock definition, implement
additional logic to have gates defined in the clk_tree and implement
variant for the infrasys ops to handle gates defined in the tree.
Similar to how it's done with factor and mux, we introduce gates_offs.
Upstream kernel follow the similar logic with all the ID defined as
FDIVS, MUXES and finally GATES.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
clk: mediatek: return XTAL rate for infrasys get_mux_rate
We currently return 0 if XTAL rate is requested in get_mux_rate. This
deviates from what is done in get_factor_rate and is totally wrong as it
can cause unwanted results (division by 0 crash)
For infrasys that makes use of CLK_XTAL, assume xtal_rate to be defined
in clk_tree and return the rate when BYPASS_XTAL is not enabled with
clk ID 0 index parents.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
clk: mediatek: return XTAL rate directly for gates with XTAL parent
There is currently a massive bug that makes any gate clk that have
CLK_XTAL as parent to return the wrong clock.
Following the code, with CLK_XTAL defined as TOPCKGEN parent, the
topckgen get_rate is called. The clk ID (0) is parsed and only in some
corner case (scenario where fixed clock are not defined) the correct
XTAL rate will be returned as get_factor or get_mux is called (that have
correct handling for CLK_XTAL). With fixed clock defined, the rate that
will be returned will always be the FIRST ELEMENT of the fixed clock
table instead of the hardcoded XTAL rate.
To handle this, add additional logic and if the flag is set to
PARENT_XTAL for the gate, return the XTAL rate directly.
We assume the clk_tree to have xtal_rate defined with clk gates that
have XTAL as parents.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Bevor this commit, only clause 22 access was possible. After this commit,
clause 45 direct access will available as well.
Note that there is a slight change of behavior: Before this commit, the
C45E bit was set to whatever value was left in the register from the
previous access. After this commit, we adopt the common practice of
discerning C45 from C22 using the devad argument.
Signed-off-by: Philip Oberfichtner <pro@denx.de> Reviewed-by: Marek Vasut <marex@denx.de>
net/tftp: make tftpput working with servers that do not use OACK
Option Acknowledgment (OACK) is an extension of TFTP protocol (see rfc2347).
Not all tftp servers implements it. For example it does not supported by
tftpd server from debian-11 (https://packages.debian.org/bullseye/tftpd).
Starting the "tftpput $loadaddr $size out_file" command with such server
will results in the following packets flow:
eth_env_set_enetaddr_by_index() declaration is duplicated in eth_internal.h
and net.h, but all units including eth_internal.h already include net.h.
Remove the superfluous declaration.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Tom Rini [Wed, 31 Jul 2024 19:39:14 +0000 (13:39 -0600)]
Merge tag 'video-20240731' of https://source.denx.de/u-boot/custodians/u-boot-video
- improve video sync performance with background syncing (cyclic)
- fix dropping characters when pasting commands over the UART
- enable background syncing by default for boards using VIDEO
- make sandbox video more responsive
Simon Glass [Fri, 26 Jul 2024 12:36:09 +0000 (06:36 -0600)]
usb: bootm: Drop old USB-device-removal code
USB is stopped using driver model now, in dm_remove_devices_flags() in
announce_and_cleanup() at the top of this file.
The usb_stop() call actually unbinds devices.
When a USB device is unbound, it causes any bootflows attached to it to
be removed, via a call to bootdev_clear_bootflows() from
bootdev_pre_unbind(). This obviously makes it impossible to boot the
bootflow.
However, when booting a bootflow that relies on USB, usb_stop() is
called, which unbinds the device. At that point any information
attached to the bootflow is dropped.
This is quite risky since the contents of freed memory are not
guaranteed to remain unchanged. Depending on what other options are
done before boot, a hard-to-find bug may crop up.
Drop the call to this old function.
Leave the netconsole call there, since this needs conversion to
driver model.
Raymond Mao [Thu, 25 Jul 2024 13:57:51 +0000 (06:57 -0700)]
tools: Add script to update git subtree projects
Recently we are introducing multiple git subtree projects and
it is the right time to have a universal script to update
various subtrees and replace the dts/update-dts-subtree.sh.
update-subtree.sh is a wrapper of git subtree commands.
Usage: From U-Boot top directory,
run
$ ./tools/update-subtree.sh pull <subtree-name> <release-tag>
for pulling a tag from the upstream.
Or run
$ ./tools/update-subtree.sh pick <subtree-name> <commit-id>
for cherry-pick a commit from the upstream.
Currently <subtree-name> supports dts, mbedtls and lwip.
Signed-off-by: Raymond Mao <raymond.mao@linaro.org>
# 2. Restore default environment and save to MMC
=> env default -a -f
=> saveenv
# 3. Read back mmc0boot1 and confirm the env is present
=> mmc read ${loadaddr} 0 400
=> md ${loadaddr} 4 82000000: 13e0632e726464617469665f3978303d .c..addr_fit=0x9
Fixes: 5b4acb0ff79d ("env: mmc: Apply GPT only on eMMC user HW partition") Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Jiaxun Yang [Wed, 17 Jul 2024 08:07:02 +0000 (16:07 +0800)]
Kconfig: Unify endian support option
Move SUPPORT_BIG_ENDIAN, SUPPORT_LITTLE_ENDIAN to top-level
arch Kconfig and let architectures select them as necessary.
Remove if guard for Endianness selection choice so we can
have one of SYS_BIG_ENDIAN, SYS_LITTLE_ENDIAN config symbol
defined even on single endian system.
Default endian to SYS_BIG_ENDIAN for MIPS || MICROBLAZE
and LITTLE_ENDIAN for the rest to retain old config
behaviour.
Note: PPC, SH, Xtensa are technically bi-endian, but I
checked compiled u-boot image with readelf, U-Boot currently
only support little endian for SH and Xtensa, Big Endian for
PPC.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Simon Glass [Wed, 31 Jul 2024 14:44:10 +0000 (08:44 -0600)]
video: Use cyclic to handle video sync
At present U-Boot flushes the cache after every character written to
the display. This makes the command-line slower, to the point that
pasting in long strings can fail.
Add a cyclic function to sync the display every 10ms. Enable this by
default.
Allow much longer times for sandbox, since the SDL display is quite
slow.
Avoid size growth if the feature is disabled by making the new init and
destroy functions dependent on CYCLIC being enabled.
Simon Glass [Wed, 31 Jul 2024 14:44:09 +0000 (08:44 -0600)]
video: Move last_sync to private data
Rather than using a static variable, use the video device's private
data to remember when the last video sync was completed. This allows
each display to have its own sync and avoids using static data in SPL.
Simon Glass [Wed, 31 Jul 2024 14:44:08 +0000 (08:44 -0600)]
cyclic: Add a symbol for SPL
The cyclic subsystem is currently enabled either in all build phases
or none. For tools this should not be enabled, but since lib/shc256.c
and other files include watchdog.h in the host build, we must make
sure that it is not enabled there.
Add an SPL symbol so that there is more control of this.
Add an include into cyclic.h so that tools can include this file.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Devarsh Thakkar <devarsht@ti.com> Reviewed-by: Stefan Roese <sr@denx.de>
Tom Rini [Wed, 31 Jul 2024 13:20:32 +0000 (07:20 -0600)]
Merge tag 'efi-2024-10-rc2' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request efi-2024-10-rc2
Documentation:
* Add a description for bootmeth_android
UEFI:
* Provide and use function list_count_nodes()
* Require EFI boot manager for EBBR compliance
* Correct check in efi_load_option_dp_join()
* Adjust config options for capsule updates
dm: use list_count_nodes() for counting list nodes
The linux kernel has the list_count_nodes() API functions which is
used for counting nodes of a list. This has now been imported in
U-Boot as part of an earlier commit. Use this function and drop the
list_count_items().
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
efi_memory: avoid possible null pointer dereference
Populate the previous memory descriptor node pointer only after it's
parent struct has been initialised. The compiler fixes this logic to
do the right thing, but it is better to have correct code in place.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Ilias Apalodimas [Thu, 20 Jun 2024 20:15:31 +0000 (23:15 +0300)]
efi_loader: adjust config options for capsule updates
EFI_IGNORE_OSINDICATIONS is used to ignore OsIndications if setvariable
at runtime is not supported and allow the platform to perform capsule
updates on disk. With the recent changes boards can conditionally enable
setvariable at runtime using EFI_RT_VOLATILE_STORE.
Let's make that visible in our Kconfigs and enable EFI_IGNORE_OSINDICATIONS
when set variable at runtime is disabled.
Since EFI_RT_VOLATILE_STORE needs help from the OS to persist the
variables, allow users to ignore OsIndications even if setvariable at
runtime is enabled.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
v2 changes:
* Drop sw_blink_state structure, move its necessary fields to
led_uc_plat structure.
* Add cyclic_info pointer to led_uc_plat structure. This
simplify code a lot.
* Remove cyclic function search logic. Not needed anymore.
* Fix blinking period. It was twice large.
* Other cleanups.
v3 changes:
* Adapt code to recent cyclic function changes
* Move software blinking functions to separate file
* Other small changes
v4 changes:
* Refactoring of led_set_period() function
v5 changes
* Fix compilation if CONFIG_LED_BLINK is not defined
v6 changes:
* Enable LEDST_BLINK state unconditionally.
* Function led_set_period() becomes available when CONFIG_LED_BLINK
is disabled. This makes led code simpler.
* Software blinking requires about 100 bytes of data for a led. It's
not a good idea to allocate so much memory for each supported led.
Change the code to allocate blinking data only for required leds.
If hardware (or driver) doesn't support leds blinking, it's
now possible to use software implementation of blinking instead.
This relies on cyclic functions.
Signed-off-by: Michael Polyntsov <michael.polyntsov@iopsys.eu> Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu> Reviewed-by: Simon Glass <sjg@chromium.org>
Changes:
* enable LEDST_BLINK state unconditionally
* function led_set_period() becomes available when CONFIG_LED_BLINK
is disabled. This makes led code simpler.
* fix cmd/led.c to work properly when LEDST_BLINK present, but
CONFIG_LED_BLINK is disabled
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu> Reviewed-by: Simon Glass <sjg@chromium.org>
projects / u-boot.git / log