From 62c390f8a3f0aabe61656d6996f1d49766de2c20 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Mon, 14 Sep 2015 08:47:47 +0200 Subject: [PATCH] mtd: nand: fsmc: Fixes and cleanup for fsmc_nand_switch_ecc() This patch addresses some comments raised by Scott in the last versions. Here the changes in detail: - Removed __maybe_unused as its not needed - Added check for strength == 4 and error out for the unsupported ECC strength values - Don't set .caclulate, .correct, and .bytes for NAND_ECC_SOFT_BCH as this will be done in nand_scan_tail() - Set .caclulate back to fsmc_read_hwecc() in the HW case - Added comment that this function will only be called on SPEAr platforms, not supporting the BCH8 HW ECC (FSMC_VER8) Signed-off-by: Stefan Roese Cc: Scott Wood Cc: Tom Rini Acked-by: Scott Wood --- drivers/mtd/nand/fsmc_nand.c | 21 +++++++++++++++------ 1 file changed, 15 insertions(+), 6 deletions(-) diff --git a/drivers/mtd/nand/fsmc_nand.c b/drivers/mtd/nand/fsmc_nand.c index 0976a67ff8..e0e9e1ebd0 100644 --- a/drivers/mtd/nand/fsmc_nand.c +++ b/drivers/mtd/nand/fsmc_nand.c @@ -13,7 +13,6 @@ #include #include #include -#include #include #include #include @@ -398,12 +397,18 @@ static int fsmc_read_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, * @eccstrength - the number of bits that could be corrected * (1 - HW, 4 - SW BCH4) */ -int __maybe_unused fsmc_nand_switch_ecc(uint32_t eccstrength) +int fsmc_nand_switch_ecc(uint32_t eccstrength) { struct nand_chip *nand; struct mtd_info *mtd; int err; + /* + * This functions is only called on SPEAr600 platforms, supporting + * 1 bit HW ECC. The BCH8 HW ECC (FSMC_VER8) from the ST-Ericsson + * Nomadik SoC is currently supporting this fsmc_nand_switch_ecc() + * function, as it doesn't need to switch to a different ECC layout. + */ mtd = &nand_info[nand_curr_device]; nand = mtd->priv; @@ -413,14 +418,18 @@ int __maybe_unused fsmc_nand_switch_ecc(uint32_t eccstrength) nand->ecc.bytes = 3; nand->ecc.strength = 1; nand->ecc.layout = &fsmc_ecc1_layout; + nand->ecc.calculate = fsmc_read_hwecc; nand->ecc.correct = nand_correct_data; - } else { + } else if (eccstrength == 4) { + /* + * .calculate .correct and .bytes will be set in + * nand_scan_tail() + */ nand->ecc.mode = NAND_ECC_SOFT_BCH; - nand->ecc.calculate = nand_bch_calculate_ecc; - nand->ecc.correct = nand_bch_correct_data; - nand->ecc.bytes = 7; nand->ecc.strength = 4; nand->ecc.layout = NULL; + } else { + printf("Error: ECC strength %d not supported!\n", eccstrength); } /* Update NAND handling after ECC mode switch */ -- 2.39.5