Wolfgang Denk [Mon, 16 Apr 2012 21:01:12 +0000 (23:01 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm:
ARM926EJS: Fix cache.c to comply with checkpatch.pl
ARM926EJS: Make asm routines volatile in cache ops
MX35: mx35pdk: wrong board revision
ARM1136: MX35: Make asm routines volatile in cache ops
ARM: add u-boot.imx as target for i.MX SOCs
M28: Pull out CONFIG_APBH_DMA so it's always enabled
DMA: Split the APBH DMA init into block and channel init
imx: Return gpio_set_value in gpio_direction_output
imx: Use GPIO_TO_PORT macro in the gpio driver instead of (gpio >> 5)
imx: Add GPIO_TO_PORT macro in the mxc_gpio driver
imx: Remove unneeded/repititive definitions from imx headers
i.MX28: Allow coexistence of PIO and DMA mode for SD/MMC
MX31: mx31pdk: drop enable_caches from board file
i.MX28: Fix initial stack pointer position
mx35: mx35pdk: fix when cache functions are linked
mx35: flea3: fix when cache functions are linked
ARM: 926ejs: use debug() for misaligned addresses
ARM1136: add cache flush and invalidate operations
mx6qsabrelite: Fix the serial console port
mx6qsabrelite: Add boot switch setting information into the README
i.MX6: mx6qsabrelite: add cache commands if cache is enabled
i.MX6: implement enable_caches()
i.MX6: define CACHELINE_SIZE
MX53: DDR: Fix ZQHWCTRL field TZQ_CS
mx28evk: Add a README file
mx28: Split the README into a common part and a m28 specific part
tricorder: Load kernel from ubifs
tricorder: Add UBIFS
cm-t35: fix Ethernet reset timing
hawkboard: Add CONFIG_SPL_LIBGENERIC_SUPPORT
BeagleBoard: Remove userbutton command and use gpio command instead
OMAP: Move omap1510inn to Unmaintained / Orphaned
Marek Vasut [Sun, 8 Apr 2012 17:34:46 +0000 (17:34 +0000)]
DMA: Split the APBH DMA init into block and channel init
This fixes the issue where mxs_dma_init() was called either twice or never,
without introducing any new init hooks.
The idea is to allow each and every device using the APBH DMA block to
configure and request only the channels it uses, instead of making it call init
for all the channels as is now.
The common DMA block init part, which only configures the block, is then called
from CPUs arch_cpu_init() call.
NOTE: This patch depends on:
http://patchwork.ozlabs.org/patch/150957/
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Marek Vasut [Thu, 5 Apr 2012 03:30:35 +0000 (03:30 +0000)]
i.MX28: Allow coexistence of PIO and DMA mode for SD/MMC
This SD DMA function of i.MX28 is still apparently too experimental to be
enabled by default in 2012.04 release. Enable this feature only if the user
plans to tinker with DCache or explicitly enables it.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com>
introduced usage of GENERATED_GBL_DATA_SIZE and calculation of initial stack
pointer position defived from that. Due to a small typo, the SP position moved
to 0x21f80, which is past the SRAM area. This didn't manifest on the real
hardware as the SRAM repeats there (address bits in the CPU being ignored).
Though this was caught in QEMU, where it crashed the emulator.
Misaligned warnings are useful to debug faulty drivers.
A misaligned warning is printed also when the driver
is correct - use debug() instead of printf().
Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Albert Aribaud <albert.u.boot@aribaud.net> CC: Mike Frysinger <vapier@gentoo.org> CC: Marek Vasut <marex@denx.de> Acked-by: Marek Vasut <marex@denx.de>
ARM1136: add cache flush and invalidate operations
Since commit 5c1ad3e6f8ae578bbe30e09652f1531e9bc22031
(net: fec_mxc: allow use with cache enabled) the FEC_MXC
driver uses flush_dcache_range() and invalidate_dcache_range()
functions. This driver is also configured for ARM1136 based
'flea3' and 'mx35pdk' boards which currently do not build
as there are no ARM1136 specific flush_dcache_range() and
invalidate_dcache_range() functions. Add various ARM1136
cache functions to fix building for 'flea3' and 'mx35pdk'.
Signed-off-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> CC: Mike Frysinger <vapier@gentoo.org> CC: Marek Vasut <marex@denx.de> Acked-by: Marek Vasut <marex@denx.de>
Bernhard Walle [Tue, 3 Apr 2012 00:37:03 +0000 (00:37 +0000)]
tricorder: Add UBIFS
Since kernel should be in a ubifs partition, we need UBIFS.
The greater malloc size is needed for UBIFS.
Signed-off-by: Bernhard Walle <walle@corscience.de>
Squashed two commits (UBIFS enabled and malloc size increased) into one. Signed-off-by: Thomas Weber <weber@corscience.de>
Tom Rini [Wed, 28 Mar 2012 06:26:19 +0000 (06:26 +0000)]
OMAP: Move omap1510inn to Unmaintained / Orphaned
After removing omap1610inn for not building, move omap1510inn to
orphaned. Also update boards.cfg to note it's part of the 'omap' SoC to
make sure the board is built more often and future breakage noticed
quicker.
Acked-by: Marek Vasut <marex@denx.de> Signed-off-by: Tom Rini <trini@ti.com>
mkenvimage.c: In function ‘main’:
mkenvimage.c:218: warning: format ‘%ld’ expects type ‘long int’, but argument 3 has type ‘unsigned int’
mkenvimage.c:226: warning: format ‘%ld’ expects type ‘long int’, but argument 3 has type ‘unsigned int’
Wolfgang Denk [Mon, 9 Apr 2012 19:34:27 +0000 (21:34 +0200)]
Merge branch 'marek.vasut@gmail.com' of git://git.denx.de/u-boot-staging
* 'marek.vasut@gmail.com' of git://git.denx.de/u-boot-staging:
LMB: Fix undefined lmb_reserve() on non-lmb platforms
MIPS: fix endianess handling
MIPS: fix inconsistency in config option for cache operation mode
MIPS: board.c: fix init of flash data in bd_info
Wolfgang Denk [Mon, 9 Apr 2012 15:10:01 +0000 (17:10 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-net
* 'master' of git://git.denx.de/u-boot-net:
net/designware: Change timeout loop implementation
net/designware: Set ANAR to 0x1e1
net/designware: Program phy registers when auto-negotiation is ON
net/designware: Try configuring phy on each dw_eth_init
net/designware: Consecutive writes must have delay
net/designware: Phy address fix
net/designware: Fix the max frame length size
net/designware: Fix to restore hw mac address
microblaze: Wire up LL_TEMAC driver initialization
microblaze: Add faked LL_TEMAC driver configuration
microblaze: Enable several ethernet driver compilation
net: ll_temac: Add LL TEMAC driver to u-boot
Update net subsystem maintainer in doc/git-mailrc
net/eth.c: fix eth_write_hwaddr() to use dev->enetaddr as fall back
mvgbe: remove warning for unused methods
Wolfgang Denk [Mon, 9 Apr 2012 15:07:50 +0000 (17:07 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-onenand
* 'master' of git://git.denx.de/u-boot-onenand:
onenand: samsung: Enable OneNAND support at Samsung's Exynos4210
onenand: Replace ONENAND_IS_MLC() with ONENAND_HAS_4KB()
onenand:samsung OneNAND chip probe functions added for GONI and Exynos4210
onenand:samsung Target dependent OneNAND chip probe function
Wolfgang Denk [Mon, 9 Apr 2012 15:00:45 +0000 (17:00 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-nios
* 'master' of git://git.denx.de/u-boot-nios:
nios2 - adjust gbl data off to account for bd_info
nios2: implement get_ticks and get_tbclk
nios2: add flush_dcache_range function
Marek Vasut [Sun, 1 Apr 2012 03:59:46 +0000 (03:59 +0000)]
LMB: Fix undefined lmb_reserve() on non-lmb platforms
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Stephen Warren <swarren@nvidia.com> Cc: Tom Warren <TWarren@nvidia.com> Cc: Graeme Russ <graeme.russ@gmail.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
Vikas Manocha [Mon, 26 Mar 2012 00:09:57 +0000 (00:09 +0000)]
net/designware: Program phy registers when auto-negotiation is ON
If AN(auto-negotiation) is ON, speed bit of control register are not
applicable. Also phy registers were not getting programmed as per the
result of AN. This patch sets only AN bit & restart AN bit for AN ON
selection & programs PHY registers as per AN result.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>
Vipin Kumar [Mon, 26 Mar 2012 00:09:56 +0000 (00:09 +0000)]
net/designware: Try configuring phy on each dw_eth_init
Phy autonegotiation works only when the ethernet cable is plugged in.
Since the phy was configured only at the init time, a plugged in cable
was necessary to initialize the phy properly.
This patch keeps a flag to check if the phy initialization has
succeeded, and calls configure_phy routine at every init if this flag
reports otherwise.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>
Armando Visconti [Mon, 26 Mar 2012 00:09:55 +0000 (00:09 +0000)]
net/designware: Consecutive writes must have delay
This patch solves a TX/RX problem which happens at 10Mbps, due to the
fact that we are not respecting 4 cyles of the phy_clk (2.5MHz) between
two consecutive writes on the same register.
Signed-off-by: Armando Visconti <armando.visconti@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>
Vipin KUMAR [Mon, 26 Mar 2012 00:09:53 +0000 (00:09 +0000)]
net/designware: Fix the max frame length size
The max frame length for normal descriptor can be 0x7FF i.e 2047. It was wrongly
specified as 2048. Currently, the max descriptor length is around 1500, so
redefining the mask to 1600
Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>
Vipin KUMAR [Mon, 26 Mar 2012 00:09:52 +0000 (00:09 +0000)]
net/designware: Fix to restore hw mac address
The network controller mac resets hardware address stored in MAC_HI and MAC_LO
registers if mac is resetted. So, hw mac address needs to be restored in case
mac is explicitly resetted from driver.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>
Expand the specific configuration for the microblaze-generic
board in xparameters.h with a faked setup to enable the
LL_TEMAC driver.
Note: From now the microblaze-generic board is no longer a
valid board configuration for a real piece of hardware. Rather
than, we use the file config.mk and xparameters.h as a faked
board configuration to force the compilation of all potential
driver code for Microblaze systems.
Eric Miao [Wed, 18 Jan 2012 22:56:33 +0000 (22:56 +0000)]
net/eth.c: fix eth_write_hwaddr() to use dev->enetaddr as fall back
Ignore the return value of eth_getenv_enetaddr_by_index(), and if it
fails, fall back to use dev->enetaddr, which could be filled up by
the ethernet device driver:
With the current code, introduced with below commit, eth_write_hwaddr()
will fail immediately if there is no eth<n>addr in the environment variables.
However, e.g. for an overo based product that uses the SMSC911x ethernet
chip (with the MAC address set via EEPROM connected to the SMSC911x chip),
the MAC address is still OK.
On mx28 boards that are depending on the OCOTP bits to set the MAC address
(like the Denx m28 board), the OCOTP bits should be used instead of
failing on the environment variables.
Signed-off-by: Eric Miao <eric.miao@linaro.org> Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Dirk Behme <dirk.behme@de.bosch.com> CC: Stefan Roese <sr@denx.de> CC: Eric Miao <eric.miao@linaro.org> CC: Wolfgang Denk <wd@denx.de> CC: Philip Balister <philip@balister.org> CC: Zach Sadecki <zach@itwatchdogs.com>
Stefan Bigler [Mon, 26 Mar 2012 00:02:13 +0000 (00:02 +0000)]
mvgbe: remove warning for unused methods
Some baords may use the GBE interface but they have no
phy connected to the interface and a direct MAC/MAC interface.
For them we need to get rid of compiler warnings.
Marek Vasut [Sun, 1 Apr 2012 03:59:46 +0000 (03:59 +0000)]
LMB: Fix undefined lmb_reserve() on non-lmb platforms
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Stephen Warren <swarren@nvidia.com> Cc: Tom Warren <TWarren@nvidia.com> Cc: Graeme Russ <graeme.russ@gmail.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
Boards with CONFIG_SYS_NO_FLASH should not forced to define
CONFIG_SYS_FLASH_BASE. In this case the flash data in bd_info
should be initialized with 0 like the other archs do.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
net/altera_tse: use flush_dcache_range instead of flush_dcache
flush_dcache is not declared in the common.h API,
flush_dcache_range however is
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi> Cc: Ben Warren <biggerbadderben@gmail.com> Cc: Thomas Chou <thomas@wytron.com.tw> Acked-by: Thomas Chou <thomas@wytron.com.tw>
net/ethoc: use flush_dcache_range instead of flush_dcache
flush_dcache is not declared in the common.h API,
flush_dcache_range however is
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi> Cc: Ben Warren <biggerbadderben@gmail.com> Cc: Thomas Chou <thomas@wytron.com.tw> Acked-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Tom Warren <TWarren@nvidia.com> Cc: albert.u.boot@aribaud.net Cc: afleming@gmail.com Cc: Simon Glass <sjg@chromium.org> Cc: Stephen Warren <swarren@nvidia.com> Cc: Nicolas Pitre <nico@fluxnic.net> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de>
Marek Vasut [Wed, 14 Mar 2012 21:52:45 +0000 (21:52 +0000)]
BOOT: Add "bootz" command to boot Linux zImage on ARM
This command boots Linux zImage from where the zImage is loaded to. Passing
initrd and fdt is supported.
Tested on i.MX28 based DENX M28EVK
Tested on PXA270 based Voipac PXA270.
NOTE: This currently only supports ARM, but other architectures can be easily
added by defining bootz_setup().
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Warren <TWarren@nvidia.com> Cc: albert.u.boot@aribaud.net Cc: afleming@gmail.com, Cc: Simon Glass <sjg@chromium.org>, Cc: Stephen Warren <swarren@nvidia.com> Cc: Nicolas Pitre <nico@fluxnic.net> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de>
Fix:
drivers/mmc/libmmc.o: In function `mxsmmc_send_cmd':
/home/ag/git/u-boot/drivers/mmc/mxsmmc.c:210: undefined reference to `mxs_dma_desc_append'
/home/ag/git/u-boot/drivers/mmc/mxsmmc.c:211: undefined reference to `mxs_dma_go'
drivers/mmc/libmmc.o: In function `mxsmmc_initialize':
/home/ag/git/u-boot/drivers/mmc/mxsmmc.c:306: undefined reference to `mxs_dma_desc_alloc'
Linus Walleij [Sun, 25 Mar 2012 12:13:05 +0000 (12:13 +0000)]
pci: get rid of local prototypes
two boards were redeclaring pciauto_region_allocate() in their local
scope for no obvious reason, the function is in <pci.h> anyway,
this is probably just copying artifacts and old cruft.
Marek Vasut [Mon, 5 Mar 2012 15:10:51 +0000 (15:10 +0000)]
MAKEALL: Add -m/-M option to determine maintainers
The -m option tries to find the board in MAINTAINERS file and figure out the
email. The -M option lists boards including their maintainers emails and all
affiliated emails. There are multiple strategies used to retrieve these emails:
1) Check board/<boardname> with git log and use three most recent emails
2) Check board/<boardname> with git log and use three most used emails
3) Try finding board in MAINTAINERS file and retrieve all emails from there
The result is then sorted and unique results are retrieved and reported.
For -m option, only strategy 3) is used.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de>
Heiko Schocher [Thu, 16 Feb 2012 01:02:21 +0000 (01:02 +0000)]
command, log: print with "log show" a full logbuffer
If the logbuffer contains LOGBUFF_LEN chars, they never got
printed with the "log show" command, because chars get
printed with the following for loop:
for (i = 0; i < (size & LOGBUFF_MASK); i++) {
with size = LOGBUFF_LEN and LOGBUFF_MASK = (LOGBUFF_LEN-1)
for loop never executed ...
Fix this.
Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Detlev Zundel <dzu@denx.de>
Fixed merge conflict. Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Fri, 30 Mar 2012 18:17:11 +0000 (20:17 +0200)]
Merge branch 'master' of /home/wd/git/u-boot/custodians
* 'master' of /home/wd/git/u-boot/custodians:
lzma: fix printf warnings
Remove CONFIG_SYS_EXTBDINFO from snapper9260.h
cmd_pxe.c: fix strict-aliasing warnings
net: smc91111: use mdelay()
doc: Fix some typos in different files
disk/part.c: Fix device enumeration through API
mkenvimage: Really set the redundant byte when applicable
mkenvimage: Don't try to detect comments in the input file
mkenvimage: Use mmap() when reading from a regular file
mkenvimage: Read/Write from/to stdin/out by default or if the filename is "-"
mkenvimage: More error handling
mkenvimage: Correct an include and add a missing one
mkenvimage: correct and clarify comments and error messages
MAKEALL: display SPL size if present
ARMV7/Vexpress: add missing get_ticks() and get_tbclk()
mkenvimage: fix usage message
cmd_fat: add FAT write command
fs/fat/fat_write.c: Fix GCC 4.6 warnings
FAT write: Fix compile errors
Wolfgang Denk [Fri, 30 Mar 2012 18:17:02 +0000 (20:17 +0200)]
Merge branch 'agust@denx.de' of git://git.denx.de/u-boot-staging
* 'agust@denx.de' of git://git.denx.de/u-boot-staging:
lzma: fix printf warnings
Remove CONFIG_SYS_EXTBDINFO from snapper9260.h
cmd_pxe.c: fix strict-aliasing warnings
net: smc91111: use mdelay()
doc: Fix some typos in different files
disk/part.c: Fix device enumeration through API
mkenvimage: Really set the redundant byte when applicable
mkenvimage: Don't try to detect comments in the input file
mkenvimage: Use mmap() when reading from a regular file
mkenvimage: Read/Write from/to stdin/out by default or if the filename is "-"
mkenvimage: More error handling
mkenvimage: Correct an include and add a missing one
mkenvimage: correct and clarify comments and error messages
MAKEALL: display SPL size if present
ARMV7/Vexpress: add missing get_ticks() and get_tbclk()
mkenvimage: fix usage message
cmd_fat: add FAT write command
fs/fat/fat_write.c: Fix GCC 4.6 warnings
FAT write: Fix compile errors
Since commit 96f5c4b the needed functions (get_ticks() and get_tbclk() )
are defined for kirkwood CPUs as well. This warning is then not relevant
anymore.
Wolfgang Denk [Fri, 30 Mar 2012 16:09:08 +0000 (18:09 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm: (146 commits)
arm: Use common .lds file where possible
arm: add a common .lds link script
arm: Remove unneeded setting of LDCSRIPT
Define CPUDIR for the .lds link script
arm: Remove zipitz2 link script
Allow arch directory to contain .lds without requiring Makefile
OMAP: Remove omap1610inn-based boards
arch/arm/cpu/armv7/omap-common/clocks-common.c: Fix build warnings
board/ti/beagle/beagle.c: Fix build warnings
sdrc.c: Fix typo in do_sdrc_init() for SPL
tegra: i2c: Add I2C driver
tegra: fdt: i2c: Add extra I2C bindings for U-Boot
tegra: i2c: Select I2C ordering for Seaboard
tegra: i2c: Enable I2C on Seaboard
tegra: i2c: Select number of controllers for Tegra2 boards
tegra: i2c: Initialise I2C on Nvidia boards
tegra: Enhance clock support to handle 16-bit clock divisors
fdt: Add function to allow aliases to refer to multiple nodes
tegra: Rename NV_PA_PMC_BASE to TEGRA2_PMC_BASE
tegra: fdt: Enable FDT support for Ventana
tegra: fdt: Enable FDT support for Seaboard
tegra: usb: Enable USB on Seaboard
tegra: usb: Add common USB defines for tegra2 boards
tegra: usb: Add USB support to nvidia boards
arm: Check for valid FDT after console is up
fdt: Avoid early panic() when there is no FDT present
tegra: usb: Add support for Tegra USB peripheral
tegra: fdt: Add function to return peripheral/clock ID
usb: Add support for txfifo threshold
tegra: usb: fdt: Add USB definitions for Tegra2 Seaboard
tegra: usb: fdt: Add additional device tree definitions for USB ports
tegra: fdt: Add clock bindings for Tegra2 Seaboard
tegra: fdt: Add clock bindings
tegra: fdt: Add additional USB binding
fdt: Add tegra-usb bindings file from linux
fdt: Add staging area for device tree binding documentation
tegra: fdt: Add device tree file for Tegra2 Seaboard from kernel
tegra: fdt: Add Tegra2x device tree file from kernel
arm: fdt: Add skeleton device tree file from kernel
fdt: Add basic support for decoding GPIO definitions
fdt: Add functions to access phandles, arrays and bools
fdt: Tidy up a few fdtdec problems
fdt: Add tests for fdtdec
fdt: Add fdtdec_find_aliases() to deal with alias nodes
arm: Tegra2: Fix ELDK42 gcc failure with inline asm stack pointer load
net: fec_mxc: allow use with cache enabled
net: force PKTALIGN to ARCH_DMA_MINALIGN
i.MX28: Enable caches by default
i.MX28: Make use of the bounce buffer
i.MX28: Do data transfers via DMA in MMC driver
MMC: Implement generic bounce buffer
i.MX28: Add cache support to MXS NAND driver
i.MX28: Add cache support into the APBH DMA driver
ARM926EJS: Implement cache operations
board/vpac270/onenand.c: Fix build errors
nhk8815: fix build errors
atmel-boards: add missing atmel_mci.h
ARM: highbank: setup env from boot source register
ARM: highbank: change env config to use nvram
ARM: highbank: add reset support
ARM: highbank: Add boot counter support
ARM: highbank: change TEXT_BASE to 0x8000
ARM: highbank: fix us_to_tick calculation
ARM: highbank: add missing get_tbclk
ARM: highbank: fix warning for calxedaxgmac_initialize
net: calxedaxgmac: fix build due to missing __aligned definition
EXYNOS: Add structure for Exynos4 DMC
EXYNOS: SMDK5250: Support all 4 UARTs
ARM: fix s3c2410 timer code
ARM: davinci: fixes for cam_enc_4xx board
omap3_spi: receive transmit mode
calimain, enbw_cmc: Fix typo in comments
Davinci: ea20: use gpio framework to access gpios
OMAP3: mt_ventoux: sets its own mtdparts
OMAP3: mt_ventoux: updated timing for FPGA
twl4030: fix potential power supply handling issues
NAND: TI: fix warnings in omap_gpmc.c
cam_enc_4xx: Rename 'images' to 'imgs'
arm: Add Prep subcommand support to bootm
OMAP3: twister: add support to boot Linux from SPL
SPL: call cleanup_before_linux() before booting Linux
OMAP3: SPL: do not call I2C init if no I2C is set.
Add cache functions to SPL for armv7
devkit8000: Implement and activate direct OS boot
omap/spl: change output of spl_parse_image_header
omap-common/spl: Add linux boot to SPL
devkit8000/spl: init GPMC for dm9000 in SPL
omap-common: Add NAND SPL linux booting
devkit8000: add config for spl command
Add cmd_spl command
mx53ard: Initialize return code with error
mx53: Make PLL2 to be the parent of UART clock
configs: imx: Use CONFIG_SF_DEFAULT_CS
mx28evk: Provide default values for SPI bus and chip select
USB: ehci-mx6: Add proper IO accessors
mx6: Read silicon revision from register
i.MX28: Drop __naked function from spl_mem_init
mxs_spi: Return proper timeout error
i.MX28: Make the stabilization delays shorter
pmic_i2c: Return error in case of invalid pmic_i2c_tx_num
mx6: Remove duplicate definition of ANATOP_BASE_ADDR
mx6: Fix reset cause for Power On Reset case
i.MX6: mx6qsabrelite: add MACH_TYPE_MX6Q_SABRELITE
i.MX6: mx6q_sabrelite: add CONFIG_REVISION_TAG
i.MX28: Enable additional DRAM address bits
mx6q: mx6qsabrelite: setup_spi() should be called in board_init to allow use for environment
mx31: add "ARM11P power gating" to get_reset_cause
mx31pdk: Fix CONFIG_SYS_MEMTEST_END
efikamx: Fix CONFIG_SYS_MEMTEST_END
mx53smd: Fix CONFIG_SYS_MEMTEST_END
mx53evk: Fix CONFIG_SYS_MEMTEST_END
mx51evk: Fix CONFIG_SYS_MEMTEST_END
i.MX6: mx6qsabrelite: add ext2 support
imximage: Remove overwriting of flash_offset
IXP: Fix GPIO_INT_ACT_LOW_SET()
IXP: Fix NAND build warning on PDNB3 and SCPU
IXP: Move PDNB3 and SCPU from Makefile to boards.cfg
IXP: Squash warnings in IXP NPE
IXP: Fix missing MACH_TYPE_{ACTUX?,PNB3,DVLHOST}
IXP: Make IXP buildable with arm-linux- toolchains
Examples: Properly append LDFLAGS to LD command
SPL: Enable YMODEM support on BeagleBone and AM335x EVM
SPL: Add YMODEM over UART load support
SPL: Add README.omap3
README: document more SPL config options
spl.c: Use __noreturn decorator
config.mk: Check for -fstack-usage support
config.mk: Make cc-option create a file under include/generated
...
Simon Glass [Thu, 23 Feb 2012 03:28:41 +0000 (03:28 +0000)]
arm: add a common .lds link script
Most ARM CPUs use a very similar link script. This adds a basic
script that can be used by most CPUs.
Two new symbols are introduced which are intended to eventually be
defined on all architectures to make things easier for generic relocation
and reduce special-case code for each architecture:
__image_copy_start is the start of the text area (equivalent to the
existing _start on ARM). It marks the start of the region which must be
copied to a new location during relocation. This symbol is called
__text_start on x86 and microblaze.
__image_copy_end is the end of the region which must be copied to a new
location during relocation. It is normally equal to the start of the BSS
region, but this can vary in some cases (SPL?). Making this an explicit
symbol on its own removes any ambiguity and permits common code to always
do the right thing.
This new script makes use of CPUDIR, now defined by both Makefile and
spl/Makefile, to find the directory containing the start.o object file,
which is always placed first in the image.
To permit MMU setup prior to relocation (as used by pxa) we add an area
to the link script which contains space for this. This is taken
from commit 7f4cfcf. CPUs can put the contents in there using their
start.S file. BTW, shouldn't that area be 16KB-aligned?
Simon Glass [Mon, 21 Nov 2011 10:49:41 +0000 (10:49 +0000)]
arm: Remove unneeded setting of LDCSRIPT
This is set by the top level Makefile anyway, so drop it. This does
have the effect of changing the order - now the board link script will
have preference over the CPU one. But this seems more correct anyway.
Simon Glass [Mon, 21 Nov 2011 10:49:37 +0000 (10:49 +0000)]
Allow arch directory to contain .lds without requiring Makefile
The Makefile for a CPU is in arch/($ARCH)/cpu/$(CPU). We want to support
having an .lds file in arch/$(ARCH)/cpu without requiring an additional
Makefile there. This change makes it clear that we expect a Makefile in
the same directory as the link script except in this case.
Fix:
clocks-common.c: In function 'setup_non_essential_dplls':
clocks-common.c:323:6: warning: variable 'sys_clk_khz' set but not used
[-Wunused-but-set-variable]
clocks-common.c: In function 'setup_non_essential_dplls':
clocks-common.c:323:6: warning: variable 'sys_clk_khz' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Tom Rini <trini@ti.com>
projects / u-boot.git / log
