Tom Rini [Mon, 19 Oct 2020 13:29:05 +0000 (09:29 -0400)]
Merge tag 'u-boot-atmel-2021.01-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features for 2021.01 cycle:
This feature set brings the rework of the clock tree for sam9x60 SoC.
This makes the clock tree fully compatible with Common Clock Framework
and allows full clock configuration in U-Boot. This means that the
sam9x60 boards can boot now using U-Boot.
This also includes the definitions for sam9x60 SiPs and a divisor fix
for the clock on sama7g5 SoC.
Patrick Delaunay [Mon, 28 Sep 2020 09:30:14 +0000 (11:30 +0200)]
configs: migrate CONFIG_VIDEO_BMP_GZIP to defconfigs
Done with:
./tools/moveconfig.py VIDEO_BMP_GZIP
The 3 suspicious migration because CMD_BMP and SPLASH_SCREEN
are not activated in these defconfigs:
- trats_defconfig
- s5pc210_universal_defconfig
- trats2_defconfig
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Neil Armstrong [Fri, 2 Oct 2020 09:16:09 +0000 (11:16 +0200)]
video: dw-mipi-dsi: permit configuring the escape clock rate
The Amlogic D-PHY in the Amlogic AXG SoC Family does support a frequency
higher than 10MHz for the TX Escape Clock, thus make the target rate
configurable.
This is based on the Linux commit [1] and adapted to the U-Boot driver.
[1] a328ca7e4af3 ("drm/bridge: dw-mipi-dsi: permit configuring the escape clock rate")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Fri, 2 Oct 2020 09:16:08 +0000 (11:16 +0200)]
video: dw-mipi-dsi: driver-specific configuration of phy timings
The timing values for dw-dsi are often dependent on the used display and
according to Philippe Cornu will most likely also depend on the used phy
technology in the soc-specific implementation.
To solve this and allow specific implementations to define them as needed
add a new get_timing callback to phy_ops and call this from the dphy_timing
function to retrieve the necessary values for the specific mode.
This is based on the Linux commit [1] and adapted to the U-Boot driver.
[1] 25ed8aeb9c39 ("drm/bridge/synopsys: dsi: driver-specific configuration of phy timings")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Sean Anderson [Tue, 13 Oct 2020 19:20:52 +0000 (15:20 -0400)]
test: Fix sandbox tests failing to build
syslog_test.h is in test/log/, not include/
Fixes: 52d3df7fef ("log: Allow LOG_DEBUG to always enable log output") Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
watchdog: octeontx_wdt: Add support for start and stop
This patch enhances the Octeon TX/TX2 watchdog driver to fully enable
the WDT. With this changes, the "wdt" command is now also supported
on these platforms.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de> Cc: Aaron Williams <awilliams@marvell.com> Cc: Suneel Garapati <sgarapati@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com>
Tom Rini [Thu, 15 Oct 2020 12:20:42 +0000 (08:20 -0400)]
Merge tag 'mmc-2020-10-14' of https://gitlab.denx.de/u-boot/custodians/u-boot-mmc
- fsl_esdhc_imx cleanup
- not send cm13 if send_status is 0.
- Add reinit API
- Add mmc HS400 for fsl_esdhc
- Several cleanup for fsl_esdhc
- Add ADMA2 for sdhci
- Octeon TX: Add NAND driver (Suneel)
- Octeon TX: Add NIC driver driver (Suneel)
- Octeon TX2: Add NIC driver driver (Suneel)
- Armada 8040: Add iEi Puzzle-M80 board support (Luka)
- Armada A37xx SPI: Add support for CS-GPIO (George)
- Espressobin: Use Linux model/compatible strings (Andre)
- Espressobin: Add armada-3720-espressobin-emmc.dts from Linux (Andre)
- Armada A37xx: Small cleanup of config header (Pali)
Set the defaults on probe for the packet buffer size registers
for the i210.
The TX/RX PBSIZE register of the i210 resets to its default value
only at power-on - see Intel Ethernet Controller I210 Datasheet rev 3.5
chapter 8.3 'Internal Packet Buffer Size Registers'.
If something (another driver, another OS, etc.) modifies this register
from its default value, the e1000 driver doesn't function correctly. It
detects a hang of the transmitter and continuously resets the adapter.
Here we set this value to its default when resetting the i210 to
resolve this issue.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
checkpatch.pl: Make CONFIG_IS_ENABLED(CONFIG_*) an error
CONFIG_IS_ENABLED() takes the kconfig name without the CONFIG_ prefix,
e.g. CONFIG_IS_ENABLED(CLK) for CONFIG_CLK. Make including the prefix
an error in checkpatch.pl so calls in the wrong format aren't
accidentally reintroduced.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
CONFIG_IS_ENABLED() takes the kconfig name without the CONFIG_ prefix,
e.g. CONFIG_IS_ENABLED(CLK) for CONFIG_CLK. Some of these were being
fixed every now and then, see:
Sean Anderson [Wed, 9 Sep 2020 20:24:56 +0000 (16:24 -0400)]
time: Fix get_ticks being non-monotonic
get_ticks does not always succeed. Sometimes it can be called before the
timer has been initialized. If it does, it returns a negative errno.
This causes the timer to appear non-monotonic, because the value will
become much smaller after the timer is initialized.
No users of get_ticks which I checked handle errors of this kind. Further,
functions like tick_to_time mangle the result of get_ticks, making it very
unlikely that one could check for an error without suggesting a patch such
as this one.
This patch panics if we ever get an error. There are two cases in which
this can occur. The first is if we couldn't find/probe the timer for some
reason. One reason for this is if the timer is not available so early. This
likely indicates misconfiguration. Another reason is that the timer has an
invalid/missing device tree binding. In this case, panicing is also
correct. The second case covers errors calling get_count. This can only
occur if the timer is missing a get_count function (or on RISC-V, but that
should be fixed soon).
Fixes: c8a7ba9e6a5 Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
David Woodhouse [Tue, 4 Aug 2020 09:05:47 +0000 (10:05 +0100)]
env/ext4.c: allow loading from an EXT4 partition on the MMC boot device
This parallels what I added for FAT in commit 6731bef6966, allowing the
environment to be found in a specific partition on the device that the
board's mmc_get_env_dev() returns. On the Banana Pi R2 that means the
device that U-Boot was loaded from; either the internal eMMC or an SD
card.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Frédéric Danis [Fri, 20 Mar 2020 09:59:24 +0000 (10:59 +0100)]
cmd: Fixup DT to pass PStore Ramoops parameters
To simplify configuration and keep synchronized the PStore/Ramoops between
U-Boot and the Linux kernel, this commit dynamically adds the Ramoops
parameters defined in the U-Boot session to the Device Tree.
Signed-off-by: Frédéric Danis <frederic.danis@collabora.com> Cc: Tom Rini <trini@konsulko.com> Cc: Heinrich Schuchardt <xypron.glpk@gmx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Heiko Schocher <hs@denx.de>
Frédéric Danis [Fri, 20 Mar 2020 09:59:23 +0000 (10:59 +0100)]
test: Add PStore command tests
Add PStore command to sandbox and sandbox64 defconfigs.
Add test checking:
- 'pstore display' of all records
- 'pstore display' only the 2nd dump record
- 'pstore save' of all records
Signed-off-by: Frédéric Danis <frederic.danis@collabora.com>
[trini: Adjust to always load files from source directory] Signed-off-by: Tom Rini <trini@konsulko.com> Cc: Heinrich Schuchardt <xypron.glpk@gmx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Heiko Schocher <hs@denx.de>
Frédéric Danis [Fri, 20 Mar 2020 09:59:22 +0000 (10:59 +0100)]
cmd: Add command to display or save Linux PStore dumps
This patch adds a new pstore command allowing to display or save ramoops
logs (oops, panic, console, ftrace and user) generated by a previous
kernel crash.
PStore parameters can be set in U-Boot configuration file, or at run-time
using "pstore set" command. Records size should be the same as the ones
used by kernel, and should be a power of 2.
This command allows:
- to display uncompressed logs
- to save compressed or uncompressed logs, compressed logs are saved as a
compressed stream, it may need some work to be able to decompress it,
e.g. adding a fake header:
"printf "\x1f\x8b\x08\x00\x00\x00\x00\x00\x00\x00" |
cat - dmesg-ramoops-0.enc.z | gzip -dc"
- ECC part is not used to check memory corruption
- only 1st FTrace log is displayed or saved
Signed-off-by: Frédéric Danis <frederic.danis@collabora.com>
[trini: Minor updates for current design, correct spacing in rST] Signed-off-by: Tom Rini <trini@konsulko.com> Cc: Heinrich Schuchardt <xypron.glpk@gmx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Heiko Schocher <hs@denx.de>
Michael Walle [Mon, 12 Oct 2020 08:07:14 +0000 (10:07 +0200)]
mmc: fsl_esdhc: add ADMA2 support
Newer eSDHC controllers support ADMA2 descriptor tables which support
64bit DMA addresses. One notable user of addresses in the upper memory
segment is the EFI loader.
If support is enabled, but the controller doesn't support ADMA2, we
will fall back to SDMA (and thus 32 bit DMA addresses only).
Andre Heider [Fri, 4 Sep 2020 15:33:54 +0000 (17:33 +0200)]
arm64: dts: a3720: add support for espressobin with populated emmc
Import armada-3720-espressobin-emmc.dts from Linux, but use sdhc1 for
emmc, since our dtsi is still based on downstream and sdhc0 is used for
the sd card.
Add support for this, while retaining backward-compatibility with
existing device trees; the driver will preserve existing behavior if a
cs-gpios list is not given, or if a particular line is specified as <0>
(native).
This implementation is inspired by similar implementations in
neighboring drivers for other platforms: atmega, mxc, etc.
Signed-off-by: George Hilliard <ghilliar@amazon.com> Reviewed-by: Stefan Roese <sr@denx.de>
Luka Kovacic [Fri, 28 Aug 2020 22:35:51 +0000 (00:35 +0200)]
arm: mvebu: mvebu_armada-8k: Add support for initializing iEi Puzzle-M801 networking
Add support for the marvell,armada8040-puzzle-m801 compatible string
in the board/Marvell/mvebu_armada-8k/board.c file to initialize the
networking on iEi Puzzle-M801 board (2x CP1 1 Gb ports).
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr> Cc: Luka Perkov <luka.perkov@sartura.hr> Reviewed-by: Stefan Roese <sr@denx.de>
Suneel Garapati [Wed, 26 Aug 2020 12:37:22 +0000 (14:37 +0200)]
mtd: nand: Add NAND controller driver for OcteonTX
Adds support for NAND controllers found on OcteonTX or
OcteonTX2 SoC platforms. Also includes driver to support
Hardware ECC using BCH HW engine found on these platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Suneel Garapati <sgarapati@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
- Fix verified boot on BE targets
- Add support for multiple required keys in verified boots
- Add support for Initialization Vectors in AES keys in FIT images
- Assorted fixes in the RSA code
rsa: fix retrieving public exponent on big-endian systems
Commit fdf0819afb (rsa: fix alignment issue when getting public
exponent) changed the logic to avoid doing an 8-byte access to a
possibly-not-8-byte-aligned address.
However, using rsa_convert_big_endian is wrong: That function converts
an array of big-endian (32-bit) words with the most significant word
first (aka a BE byte array) to an array of cpu-endian words with the
least significant word first. While the exponent is indeed _stored_ as
a big-endian 64-bit word (two BE words with MSW first), we want to
extract it as a cpu-endian 64 bit word. On a little-endian host,
swapping the words and byte-swapping each 32-bit word works, because
that's the same as byte-swapping the whole 64 bit word. But on a
big-endian host, the fdt32_to_cpu are no-ops, but
rsa_convert_big_endian() still does the word-swapping, breaking
verified boot.
To fix that, while still ensuring we don't do unaligned accesses, add
a little helper that first memcpy's the bytes to a local fdt64_t, then
applies fdt64_to_cpu(). [The name is chosen based on the
[bl]eXX_to_cpup in linux/byteorder/generic.h].
Fixes: fdf0819afb ("rsa: fix alignment issue when getting public exponent") Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Reviewed-by: Simon Glass <sjg@chromium.org>
lib: rsa: check algo match in rsa_verify_with_keynode
The algo name should match between the FIT's signature node and the
U-Boot's control FDT.
If we do not check it, U-Boot's control FDT can expect sha512 hash but
nothing will prevent to accept image with sha1 hash if the signature is correct.
Philippe Reynes [Thu, 17 Sep 2020 13:01:46 +0000 (15:01 +0200)]
fit: cipher: aes: allow to store the IV in the FIT image
Binaries may be encrypted in a FIT image with AES. This
algo needs a key and an IV (Initialization Vector). The
IV is provided in a file (pointer by iv-name-hint in the
ITS file) when building the ITB file.
This commits adds provide an alternative way to manage
the IV. If the property iv-name-hint is not provided in
the ITS file, the tool mkimage will generate an random
IV and store it in the FIT image.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
This patch adds vboot tests to verify the support for multiple
required keys using new required-mode DTB policy.
This patch also fixes existing test where dev
key is assumed to be marked as not required, although
it is marked as required.
Note that this patch re-added sign_fit_norequire().
sign_fit_norequire() was removed as part of the following:
commit b008677daf2a ("test: vboot: Fix pylint errors").
This patch leverages sign_fit_norequire() to fix the
existing bug.
Signed-off-by: Thirupathaiah Annapureddy <thiruan@linux.microsoft.com> Reviewed-by: Simon Glass <sjg@chromium.org>
vboot: add DTB policy for supporting multiple required conf keys
Currently FIT image must be signed by all required conf keys. This means
Verified Boot fails if there is a signature verification failure
using any required key in U-Boot DTB.
This patch introduces a new policy in DTB that can be set to any required
conf key. This means if verified boot passes with one of the required
keys, U-Boot will continue the OS hand off.
There were prior attempts to address this:
https://lists.denx.de/pipermail/u-boot/2019-April/366047.html
The above patch was failing "make tests".
https://lists.denx.de/pipermail/u-boot/2020-January/396629.html
Signed-off-by: Thirupathaiah Annapureddy <thiruan@linux.microsoft.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Mon, 12 Oct 2020 11:26:57 +0000 (07:26 -0400)]
Merge tag 'ti-v2021.01-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-ti
- Minor cleanup on K3 env variables
- Fix OSPI compatible for J721e
- Drop unused property in omap-usb2-phy
- Update Maintainer for am335x-guardian board.
Michael Walle [Wed, 23 Sep 2020 10:42:51 +0000 (12:42 +0200)]
mmc: sdhci: move the ADMA2 table handling into own module
There are other (non-SDHCI) controllers which supports ADMA2 descriptor
tables, namely the Freescale eSDHC. Instead of copying the code, move it
into an own module.
Michael Walle [Wed, 23 Sep 2020 10:42:49 +0000 (12:42 +0200)]
mmc: fsl_esdhc: simplify esdhc_setup_data()
First, we need the waterlevel setting for PIO mode only. Secondy, both DMA
setup code is identical for both directions, except for the data pointer.
Thus, unify them.
projects / u-boot.git / log
