Tom Rini [Tue, 27 Sep 2022 12:53:51 +0000 (08:53 -0400)]
Merge tag 'u-boot-stm32-20220927' of https://source.denx.de/u-boot/custodians/u-boot-stm into next
- Increase SYS_MALLOC_F_LEN for STM32 MCU's board
- SPL fixes for STM32F7 MCUs
- Device tree alignement with kernelv6.0-rc4 for MCU's board
- Device tree alignement with kernelv6.0-rc3 for MPU's board
- Update DDR node for STM32MP15
- Cleanup config file for STM32MP1
- Update for cmd_stm32key command
- Fix compatible string to add partitions for STM32MP1
- Update for stm32programmer tool
configs: increase SYS_MALLOC_F_LEN for STM32 MCU's board
Some STM32 MCU's board need their SYS_MALLOC_F_LEN value enlarged
to avoid the "alloc space exhausted" error message during their boot
process.
Use the default SYS_MALLOC_F_LEN value which is set to 0x2000 in
Kconfig.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This is due to SYS_UBOOT_START flag set to 0x080083FD which is not correct.
If unset, SYS_UBOOT_START is set by default to CONFIG_SYS_TEXT_BASE
which match with our requirement.
arch-stm32f7/stm32.h file is shared between STM32F746 and STM32F769
MCUs. But STM32F769 embeds 2MB of internal flash instead of 1MB for
STM32F746. The flash layout is quite similar between the 2 SoCs :
STM32F746 embeds 1 MB of internal flash [0x08000000-0x080fffff],
fix CONFIG_SYS_SPL_ARGS_ADDR accordingly
It solves hard fault when jumping from SPL to U-Boot.
STM32F746 embeds 1 MB of internal flash [0x08000000-0x080fffff],
fix CONFIG_SYS_SPL_ARGS_ADDR accordingly
It solves hard fault when jumping from SPL to U-Boot.
Commit 'b4b9a00ed593 ("Convert CONFIG_SYS_SPL_ARGS_ADDR to Kconfig")'
replaces CONFIG_SYS_FDT_BASE by CONFIG_SYS_SPL_ARGS_ADDR.
As CONFIG_SYS_SPL_ARGS_ADDR enables additional code when enable, it
increases SPL size over the initial 0x8000 limit.
Increase the SPL size to 0x9000 to fix SPL boot.
Set SPL_SIZE_LIMIT to 0x9000 to avoid similar issue in the future.
Fixes 'b4b9a00ed593 ("Convert CONFIG_SYS_SPL_ARGS_ADDR to Kconfig")'
Commit 'b4b9a00ed593 ("Convert CONFIG_SYS_SPL_ARGS_ADDR to Kconfig")'
replaces CONFIG_SYS_FDT_BASE by CONFIG_SYS_SPL_ARGS_ADDR.
As CONFIG_SYS_SPL_ARGS_ADDR enables additional code when enable, it
increases SPL size over the initial 0x8000 limit.
Increase the SPL size to 0x9000 to fix SPL boot.
Set SPL_SIZE_LIMIT to 0x9000 to avoid similar issue in the future.
Fixes 'b4b9a00ed593 ("Convert CONFIG_SYS_SPL_ARGS_ADDR to Kconfig")'
Commit 'b4b9a00ed593 ("Convert CONFIG_SYS_SPL_ARGS_ADDR to Kconfig")'
replaces CONFIG_SYS_FDT_BASE by CONFIG_SYS_SPL_ARGS_ADDR.
As CONFIG_SYS_SPL_ARGS_ADDR enables additional code when enable, it
increases SPL size over the initial 0x8000 limit.
Increase the SPL size to 0x9000 to fix SPL boot.
Set SPL_SIZE_LIMIT to 0x9000 to avoid similar issue in the future.
Fixes 'b4b9a00ed593 ("Convert CONFIG_SYS_SPL_ARGS_ADDR to Kconfig")'
Michal Simek [Mon, 19 Sep 2022 12:21:10 +0000 (14:21 +0200)]
arm64: versal-net: Add support for mini configuration
Versal NET mini configuration is designed for running memory test. Current
output is on DCC but changing serial0 alias to pl011 will move console to
serial port.
Michal Simek [Mon, 19 Sep 2022 12:21:02 +0000 (14:21 +0200)]
arm64: versal-net: Add support for Versal NET platform
Versal NET platform is based on Versal chip which is reusing a lot of IPs.
For more information about new IPs please take a look at DT which describe
currently supported devices.
The patch is adding architecture and board support with soc detection
algorithm. Generic setting should be very similar to Versal but it will
likely diverge in longer run.
Rick Chen [Wed, 21 Sep 2022 06:34:54 +0000 (14:34 +0800)]
riscv: Introduce AVAILABLE_HARTS
In SMP all harts will register themself in available_hart
during start up. Then main hart will send IPI to other harts
according to this variables. But this mechanism may not
guarantee that all other harts can jump to next stage.
When main hart is sending IPI to other hart according to
available_harts, but other harts maybe still not finish the
registration. Then the SMP booting will miss some harts finally.
So let it become an option and it will be enabled by default.
Please refer to the discussion:
https://www.mail-archive.com/u-boot@lists.denx.de/msg449997.html
Signed-off-by: Rick Chen <rick@andestech.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Simon Glass [Wed, 21 Sep 2022 14:21:41 +0000 (16:21 +0200)]
sandbox: scsi: Move reply setup out of helper
Move this code out of the helper function so we can (later) add it as part
of the shared emulation code. Set a default value of 0 for buff_used since
that is what we use when there is an error.
Simon Glass [Wed, 21 Sep 2022 14:21:36 +0000 (16:21 +0200)]
scsi: Move core emulation state into a new struct
In preparation for sharing the emulation code between two drivers, move
some of the fields into a new struct. Use a separate header file so it
can be used by various drivers.
Tom Rini [Sat, 24 Sep 2022 17:58:49 +0000 (13:58 -0400)]
Merge branch '2022-09-24-add-console-flush' into next
To quote the author:
On certain places it is required to flush output print buffers to ensure
that text strings were sent to console or serial devices. For example when
printing message that U-Boot is going to boot kernel or when U-Boot is
going to change baudrate of terminal device.
Some console devices, like UART, have putc/puts functions which just put
characters into HW transmit queue and do not wait until all data are
transmitted. Doing some sensitive operations (like changing baudrate or
starting kernel which resets UART HW) cause that U-Boot messages are lost.
Therefore introduce a new flush() function, implement it for all serial
devices via pending(false) callback and use this new flush() function on
sensitive places after which output device may go into reset state.
This change fixes printing of U-Boot messages:
"## Starting application at ..."
"## Switch baudrate to ..."
In addition, take a patch from Heinrich to rename some EFI test
functions in order to not conflict with this series.
In a lot of cases kernel resets UART HW. To ensure that U-Boot messages
printed before booting the kernel are not lost, call new U-Boot console
flush() function.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Changing baudrate is a sensitive operation. To ensure that U-Boot messages
printed before changing baudrate are not lost, call new U-Boot console
flush() function.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Simon Glass <sjg@chromium.org>
serial: Implement serial_flush() function for console flush() fallback
Like in all other console functions, implement also serial_flush() function
as a fallback int console flush() function.
Flush support is available only when config option CONSOLE_FLUSH_SUPPORT is
enabled. So when it is disabled then provides just empty static inline
function serial_flush().
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Simon Glass <sjg@chromium.org>
On certain places it is required to flush output print buffers to ensure
that text strings were sent to console or serial devices. For example when
printing message that U-Boot is going to boot kernel or when U-Boot is
going to change baudrate of terminal device.
Therefore introduce a new flush() and fflush() functions into console code.
These functions will call .flush callback of associated stdio_dev device.
As this function may increase U-Boot side, allow to compile U-Boot without
this function. For this purpose there is a new config CONSOLE_FLUSH_SUPPORT
which is enabled by default and can be disabled. It is a good idea to have
this option enabled for all boards which have enough space for it.
When option is disabled when U-Boot defines just empty static inline
function fflush() to avoid ifdefs in other code.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Fri, 23 Sep 2022 22:42:53 +0000 (18:42 -0400)]
Merge branch '2022-09-23-4gb-ddr-in-32bit-ppc' into next
To quote the author, for the first 9 patches:
This patch series fixes U-Boot code to correctly handle RAM size larger
than 2 GB and then fixes fsl ddr driver to do not crash U-Boot when 4 GB
DDR module is detected when U-Boot operates in 32-bit mode (as opposite
of the 36-bit mode).
With this patch series it is possible to boot 32-bit U-Boot with 4 GB
SODIMM DDR3 module without crashes. U-Boot will still use just
CONFIG_MAX_MEM_MAPPED amount of RAM, but it is better than crashing due
to the truncating of 4GB value to 32-bit number (which is zero).
I tested this patch series on powerpc P2020 based board but only with
U-Boot v2022.04 because U-Boot master branch is still broken on P2020.
And then the final two patches here are (in my mind at least) related
clean-ups.
board_f: show_dram_config: Print also real DRAM size
32-bit U-Boot builds cannot use more than around 2 GB of DDR memory. But on
some platforms/boards it is possible to connect also 4 GB SODIMM DDR memory.
U-Boot currently prints only effective size of RAM which can use, which may
be misleading as somebody would expect that this line prints total size of
connected DDR modules. So change show_dram_config code to prints both real
and effective DRAM size if they are different. If they are same then print
just one number like before. It is possible that effective size is just few
bytes smaller than the real size, so print both numbers only in case
function print_size() prints formats them differently.
powerpc/mpc85xx: Fix re-align of unmapped DDR memory message for non-SPL builds
During init_dram() is called also setup_ddr_tlbs_phys() function which may
print message about unmapped DDR memory. So in this case print also
re-aligning filler after unmapped DDR memory message.
Currently U-Boot SPL prints just generic message "2 GiB left unmapped".
Change it to more detailed "2 GiB of DDR memory left unmapped in U-Boot".
This is just U-Boot configuration and operating system may map more (or
also less) memory.
ddr: fsl: Fix re-align of verbose DRAM information for non-SPL builds
During init_dram() is called also compute_lowest_common_dimm_parameters()
function which prints multi-line detailed output. So print also re-aligning
filler after "Detected ?DIMM" line to have "DRAM: " output aligned.
ddr: fsl: Allow to detect 4 GB DDR modules in 32-bit mode
U-Boot core code already handles the case when RAM size is bigger than
CONFIG_MAX_MEM_MAPPED. So there is no need to do duplicate check in fsl ddr
driver for CONFIG_MAX_MEM_MAPPED. Instead simplify code to just check if
RAM size can be representable in phys_size_t type. And avoid printing
warning if phys_size_t is just 1 byte smaller than RAM size, which is the
typical situation with 4 GB DDR module.
ddr: fsl: Fix fsl_ddr_sdram_size() for 4GB modules with 32-bit phys_size_t
Function fsl_ddr_compute() always return size in unsigned long long type,
but function fsl_ddr_sdram_size() returns size in phys_size_t type.
When 36-bit addressing mode is not enabled then phys_size_t type is only
32-bit and thus it cannot store value 4GB (0x100000000). Function
fsl_ddr_sdram_size() in this case returns truncated value 0x0.
Fix this issue by returning the highest representable value, which is
0xffffffff (4GB - 1 byte).
This change fixes crashing of proper U-Boot because it detected 4 GB module
as RAM with zero size.
ddr: fsl: Fix checking for maximal mappable memory
Check needs to be done against CONFIG_MAX_MEM_MAPPED macro and not fixed
size 4GB (as CONFIG_MAX_MEM_MAPPED can be lower and for example for e500
cores it is just 2GB). Also fix printf re-align, which should be applied
only for non-SPL builds, during init_dram() call.
Commit 37dc958947ed ("global_data.h: Change ram_top type to phys_addr_t")
changed type of ram_top member from ulong to phys_addr_t but did not
changed types in board_get_usable_ram_top() function which returns value
for ram_top.
So change ulong to phys_addr_t type also in board_get_usable_ram_top()
signature and implementations.
Fixes: 37dc958947ed ("global_data.h: Change ram_top type to phys_addr_t") Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Simon Glass <sjg@chromium.org>
common/memsize.c: Fix get_effective_memsize() to check for overflow
Ensure that top of RAM can be represented by phys_size_t type. If RAM is
too large or RAM base address is too upper then limit RAM size to prevent
address space overflow.
Tom Rini [Fri, 23 Sep 2022 19:09:44 +0000 (15:09 -0400)]
Merge branch '2022-09-23-add-mediatek-mt7986-support' into next
To quote the author:
This patch series add support for MediaTek MT7981/MT7986 SoCs with their
reference boards and related drivers.
This patch series add basic boot support on eMMC/SD/SPI-NOR/SPI-NAND for
these boards. The clock, pinctrl drivers and the SoC initializaton code
are also included.
Product spec for MT7986:
https://www.mediatek.com/products/home-networking/mediatek-filogic-830
tools: mtk_image: add support for nand headers used by newer chips
This patch adds more nand headers in two new types:
1. HSM header, used for spi-nand thru SNFI interface
2. SPIM header, used for spi-nand thru spi-mem interface
The original nand header is renamed to AP header.
Tested-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
tools: mtk_image: split the code of generating NAND header into a new file
The predefined NAND headers take too much spaces in the mtk_image.c.
Moving them into a new file can significantly improve the readability of
both mtk_image.c and the new mtk_nand_headers.c.
This is a preparation for adding more NAND headers.
Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
clk: mediatek: add clock driver support for MediaTek MT7986 SoC
This patch adds clock driver support for MediaTek MT7986 SoC
Reviewed-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
clk: mediatek: add CLK_BYPASS_XTAL flag to allow bypassing searching clock parent of xtal clock
The mtk clock framework in u-boot uses array index for searching clock
parent (kernel uses strings for search), so we need to specify a special
clock with ID=0 for CLK_XTAL in u-boot.
In the mt7622/mt7629 clock tree, the clocks with ID=0 never call
mtk_topckgen_get_mux_rate, adn return xtal clock directly. This what we
expected.
However for newer chips, they may have some clocks with ID=0 not
representing the xtal clock and still needs mtk_topckgen_get_mux_rate be
called. Current logic will make entire clock driver not working.
This patch adds a flag to indicate that whether a clock driver needs clocks
with ID=0 to call mtk_topckgen_get_mux_rate.
Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
timer: mtk: add support for MediaTek MT7981/MT7986 SoCs
This patch add general-purpose timer support for MediaTek MT7981/MT7986.
These two SoCs uses a newer version of timer with its register definition
slightly changed.
Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds PWM support for MediaTek MT7981 SoC.
MT7981 uses a different register offset so we have to add a version field
to indicate the IP core version.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
serial: mtk: add support for using dynamic baud clock souce
The baud clock on some platform may change due to assigned-clock-parent
set in DT. In current flow the baud clock is only retrieved during probe
stage. If the parent of the source clock changes after probe stage, the
setbrg will set wrong baudrate.
To get the right clock rate, this patch records the baud clk struct to the
driver's priv, and changes the driver's flow to get the clock rate before
calling _mtk_serial_setbrg().
Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds support for PDMA v2 hardware. The PDMA v2 has extended the
DMA descriptor to 8-words, and some of its fields have changed comparing
to the v1 hardware.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
net: mediatek: stop using bitfileds for DMA descriptors
This patch is a preparation for adding a new version of PDMA of which the
DMA descriptor fields has changed. Using bitfields will result in a complex
modification. Convert bitfields to u32 units can solve this problem easily.
Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
net: mediatek: use a struct to cover variations of all SoCs
Using a single soc id to control different initialization and TX/RX flow
for all SoCs is not extensible if more hardware variations are added in
the future.
This patch introduces a struct to replace the original mtk_soc to allow
the driver be able handle newer hardwares.
Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This patch adds general board files based on MT7981 SoCs.
MT7981 uses one mmc controller for booting from both SD and eMMC, and the
pins of mmc controller are also shared with spi controller.
So three configs are need for these boot types:
1. mt7981_rfb_defconfig - SPI-NOR and SPI-NAND
2. mt7981_emmc_rfb_defconfig - eMMC only
3. mt7981_sd_rfb_defconfig - SD only
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
MT7986 uses one mmc controller for booting from both SD and eMMC.
Both MT7986A and MT7986B use the same pins for spi controller.
Configs for various boot types:
1. mt7986_rfb_defconfig - SPI-NOR and SPI-NAND for MT7986A/B
2. mt7986a_bpir3_emmc_defconfig - eMMC for MT7986A only
3. mt7986a_bpir3_sd_defconfig - SD for MT7986A only
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Patrick Delaunay [Wed, 21 Sep 2022 07:37:13 +0000 (09:37 +0200)]
ARM: dts: stm32mp15: update DDR node
Remove the unnecessary nodes for TFABOOT and keep the mandatory part
in SOC dtsi, only the DDRCTRL and DDRPHY addresses.
This patch allows to manage the DDR configuration setting in U-Boot
device tree only if it is needed, when CONFIG_SPL is defined.
With TFABOOT, the DDR configuration is done in TF-A BL2 and the DDR size
is dynamically computed in U-Boot since commit d72e7bbe7c28 ("ram:
stm32mp1: compute DDR size from DDRCTL registers").
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
projects / u-boot.git / log
