Kever Yang [Thu, 24 Nov 2016 07:29:50 +0000 (15:29 +0800)]
rockchip: board: popmetal: de-assert the host rst pin in board init
The PopMetal board have a on board FE1.1 usb 2.0 hub which connect to
the usb host port, we need to de-assert its reset pin to enable it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org>
Added rockchip: tag: Signed-off-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Tue, 10 Jan 2017 04:32:07 +0000 (13:32 +0900)]
mmc: move more driver config options to Kconfig
Move (and rename) the following CONFIG options to Kconfig:
CONFIG_DAVINCI_MMC (renamed to CONFIG_MMC_DAVINCI)
CONFIG_OMAP_HSMMC (renamed to CONFIG_MMC_OMAP_HS)
CONFIG_MXC_MMC (renamed to CONFIG_MMC_MXC)
CONFIG_MXS_MMC (renamed to CONFIG_MMC_MXS)
CONFIG_TEGRA_MMC (renamed to CONFIG_MMC_SDHCI_TEGRA)
CONFIG_SUNXI_MMC (renamed to CONFIG_MMC_SUNXI)
They are the same option names as used in Linux.
This commit was created as follows:
[1] Rename the options with the following command:
Masahiro Yamada [Tue, 10 Jan 2017 04:32:05 +0000 (13:32 +0900)]
mmc: move DesignWare-based drivers to Kconfig
Move (and rename) the following CONFIG options to Kconfig:
CONFIG_EXYNOS_DWMMC (renamed to CONFIG_MMC_DW_EXYNOS)
CONFIG_HIKEY_DWMMC (renamed to CONFIG_MMC_DW_K3)
CONFIG_SOCFPGA_DWMMC (renamed to CONFIG_MMC_DW_SOCFPGA)
The "HIKEY" is a board name, so it is not suitable for the MMC
controller name. I am following the name used in Linux.
This commit was generated as follows:
[1] Rename the config options with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e '
s/CONFIG_EXYNOS_DWMMC/CONFIG_MMC_DW_EXYNOS/g
s/CONFIG_HIKEY_DWMMC/CONFIG_MMC_DW_K3/g
s/CONFIG_SOCFPGA_DWMMC/CONFIG_MMC_DW_SOCFPGA/g
'
[2] Commit the changes
[3] Create the entries in drivers/mmc/Kconfig
(with default y for EXYNOS and SOCFPGA)
[4] Run the following:
tools/moveconfig.py -y -r HEAD MMC_DW_EXYNOS MMC_DW_K3 MMC_DW_SOCFPGA
[5] Sort and align drivers/mmc/Makefile for readability
[6] Clean-up doc/README.socfpga by hand
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Marek Vasut <marex@denx.de>
Masahiro Yamada [Tue, 10 Jan 2017 04:32:04 +0000 (13:32 +0900)]
mmc: move CONFIG_DWMMC to Kconfig, renaming to CONFIG_MMC_DW
This commit was created as follows:
[1] Rename the option with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e 's/CONFIG_DWMMC/CONFIG_MMC_DW/g'
[2] create the entry for MMC_DW in drivers/mmc/Kconfig
(the prompt and help were copied from Linux)
[3] run "tools/moveconfig.py -y MMC_DW"
[4] add "depends on MMC_DW" to the MMC_DW_ROCKCHIP entry
[5] Clean-up doc/README.socfpga by hand
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Marek Vasut <marex@denx.de>
Masahiro Yamada [Tue, 10 Jan 2017 04:32:02 +0000 (13:32 +0900)]
ARM: socfpga: remove unused CONFIG option and cleanup README.socfpga
CONFIG_SOCFPGA_DWMMC_FIFO_DEPTH is defined in the socfpga_common.h,
but not referenced at all. Remove.
Also, clean-up the README.socfpga. CONFIG_MMC should not be defined
in the header since it was moved to Kconfig by commit c27269953b94
("mmc: complete unfinished move of CONFIG_MMC"). I see no grep hit
for the others.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Marek Vasut <marex@denx.de>
Masahiro Yamada [Fri, 30 Dec 2016 14:20:14 +0000 (23:20 +0900)]
mmc: uniphier-sd: fix Kconfig dependency
Some MMC drivers describe operations with the DM_MMC_OPS form, but
there are still several drivers with older implementation. We can
not compile drivers from different groups at the same time because
the core framework is shared with #ifdef CONFIG_DM_MMC_OPS.
Every driver should have "depends on DM_MMC_OPS" (or !DM_MMC_OPS)
explicitly to express which framework it is based on. This will
avoid enabling drivers with incompatible interface at the same time.
It is incorrect to make a driver "select DM_MMC_OPS".
While we are here, add "depends on OF_CONTROL" as well because this
driver can be configured only by Device Tree.
Jaehoon Chung [Fri, 30 Dec 2016 06:30:11 +0000 (15:30 +0900)]
mmc: sdhci: disable the 8bit mode when host doesn't support it
Buswidth is depeneded on Hardware schematic.
Evne though host can support the 8bit buswidth, if hardware doesn't
support 8bit mode, it doesn't work fine.
So the buswidth mode selection leaves a matter in each SoC drivers.
On the contrary to this, hardware supports 8bit mode, but host doesn't
support it. then controller has to disable the MMC_MODE_8BIT.
(Host can check whether 8bit mode is supported or not, since V3.0)
Kamensky Ivan [Tue, 27 Dec 2016 16:12:23 +0000 (19:12 +0300)]
xilinx_phy: Pass correct pointer to fdtdec_get_int()
This patch fixes incorrect pointer on offset device in device tree blob.
When using with the component "Ethernet 1G/2.5G BASE-X PCS/PMA or SGMII"
it does not understand what type is XAE_PHY_TYPE_1000BASE_X and trying
to change frequency.
Signed-off-by: Kamensky Ivan <kamensky.ivan@mail.ru> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Michal Simek [Mon, 9 Jan 2017 09:05:16 +0000 (10:05 +0100)]
ARM64: zynqmp: Generate handoff structure for ATF
Xilinx ATF extending options for passing images from BL2(FSBL)
to BL31. U-Boot SPL is FSBL replacement that's why it should generate
handoff structure the same. Support only one entry which is U-Boot in
EL2 itself. When FIT image is adopted structure generate should be data
driven.
Currently ATF is placing this structure at the beggining of OCM which is
rewriting early parts of ATF which should be unused at that time.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Moritz Fischer [Thu, 22 Dec 2016 17:36:11 +0000 (09:36 -0800)]
ARM64: zynqmp: Fix i2c node's compatible string
The Zynq Ultrascale MP uses version 1.4 of the Cadence IP core
which fixes some silicon bugs that needed software workarounds
in Version 1.0 that was used on Zynq systems.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Heiko Schocher <hs@denx.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ARM64: zynqmp: Enable fastboot for first SD/MMC/EMMC device
DNL numbers are not changed that's why fastboot needs to be called with
-i parameter (Xilinx vendor id).
- Show available devices
sudo fastboot -i 0x03fd devices
xilinx_zynqmp_zcu100 fastboot
- Stop fastboot and go back to U-Boot prompt
sudo fastboot -i 0x03fd continue
- Reboot the board
sudo fastboot -i 0x03fd reboot
- Get internal variables
sudo fastboot -i 0x3fd getvar bootloader-version
bootloader-version: U-Boot 2016.07-00026-g19bd53044817
sudo fastboot -i 0x3fd getvar downloadsize
downloadsize: 0x06000000
sudo fastboot -i 0x3fd getvar version
version: 0.4
(regular variables needs to have fastboot. prefix - there is also
serialno variable which should be define as serial#)
- Format SD/MMC/EMMC card
sudo fastboot -i 0x3fd oem format
- Write images to boot and Linux partition
sudo fastboot -i 0x3fd flash boot sd.img
sudo fastboot -i 0x3fd flash Linux os.img
Added the idle-states node to describe zynqmp idle states. Only cpu-sleep-0
idle state is added in this patch. References to the idle-states node are
added in all CPU nodes. Time values: entry/exit latencies and min-residency,
needs to be tuned. arm,psci-suspend-param is selected to comply with PSCIv1.0
and Extended StateID format.
Signed-off-by: Stefan Krsmanovic <stefan.krsmanovic@aggios.com> Acked-by: Will Wong <willw@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Sudeep Holla [Wed, 21 Oct 2015 10:10:16 +0000 (11:10 +0100)]
ARM: dts: zynq: replace gpio-key,wakeup with wakeup-source property
Though the keyboard driver for GPIO buttons(gpio-keys) will continue to
check for/support the legacy "gpio-key,wakeup" boolean property to
enable gpio buttons as wakeup source, "wakeup-source" is the new
standard binding.
This patch replaces the legacy "gpio-key,wakeup" with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.
Cc: Michal Simek <michal.simek@xilinx.com> Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support to save environment as a file of FAT filesystem
on to SD card. The file will be saved with name uEnv.txt.
This environment will be retrieved during boot.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 2 Jan 2017 08:40:09 +0000 (09:40 +0100)]
scsi: dm: Unbind all scsi based block devices before new scan
New scan should unbind all block devices not to be listed again.
Without this patch if scsi reset or scan is called new block devices are
created which point to the same id and lun.
For example:
ZynqMP> scsi scan
scsi_scan: if_type=2, devnum=0: sdhci@ff170000.blk, 6, 0
scsi_scan: if_type=2, devnum=0: ahci@fd0c0000.id1lun0, 2, 0
scsi_scan: if_type=2, devnum=0: ahci@fd0c0000.id1lun0, 2, 1
scsi_scan: if_type=2, devnum=0: ahci@fd0c0000.id1lun0, 2, 2
scsi_scan: if_type=2, devnum=0: ahci@fd0c0000.id1lun0, 2, 3
scsi_scan: if_type=2, devnum=0: ahci@fd0c0000.id1lun0, 2, 4
scanning bus for devices...
Device 0: (1:0) Vendor: ATA Prod.: KINGSTON SVP200S Rev: 501A
Type: Hard Disk
Capacity: 57241.8 MB = 55.9 GB (117231408 x 512)
Reported-by: Ken Ma <make@marvell.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Simon Glass <sjg@chromium.org>
Jagan Teki [Thu, 5 Jan 2017 14:32:50 +0000 (15:32 +0100)]
mx6ullevk: Add missing MAINTAINERS for mx6ull_14x14_evk_plugin_defconfig
Add 'Peng Fan' as MAINTAINERS of configs/mx6ull_14x14_evk_plugin_defconfig
which is missing in below commit
"imx: mx6ull_14x14_evk: add plugin defconfig"
(sha1: b90ebf49bb8f74afe68f696f59a0e24cc79f2031)
Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Jagan Teki <jagan@openedev.com>
Andrew F. Davis [Fri, 6 Jan 2017 22:32:12 +0000 (16:32 -0600)]
am335x: configs: Use ISW_ENTRY_ADDR to set SPL_TEXT_BASE
The SPL load address changes based on boot type in HS devices,
ISW_ENTRY_ADDR is used to set this address for AM43xx based SoCs
for similar reasons. Add this same logic for AM33xx devices.
Also make the default value for ISW_ENTRY_ADDR correct for GP
devices based on SoC, HS devices already pick the correct
value in their defconfig.
Andrew F. Davis [Fri, 6 Jan 2017 22:20:02 +0000 (16:20 -0600)]
arm: mach-omap2: Fix secure file generation
When TI_SECURE_DEV_PKG is not defined we warn that the file '*_HS' was
not generated but generate an unsigned one anyway, first fix this
warning to say that it was generated but not secured.
When the user then exports TI_SECURE_DEV_PKG after getting this warning,
and tries to re-build, 'make' will detect the build artifacts as
unchanged and so assume they do not need to be re-generated. This causes
it to fail to sign the files and it will pack unsigned files into the
final image, even though TI_SECURE_DEV_PKG is now correctly defined and
working.
Fix this by using FORCE on the targets causes them to be re-run even if
the dependent files have not changed.
This then causes another issue. We currently rename the signed dtb files
to overwrite the non-signed ones. We do this so the 'mkimage' tool gives
the packaged dtb sections the correct name. If we do not rename the files
then SPL will not find them during boot.
Fix this by renaming the dtb files by appending _HS to the end of the
filename, after the ".dtb", this causes them to still be named correctly
in the FIT blob.
York Sun [Wed, 28 Dec 2016 16:43:45 +0000 (08:43 -0800)]
ddr: fsl: Merge macro CONFIG_NUM_DDR_CONTROLLERS and CONFIG_SYS_NUM_DDR_CTRLS
These two macros are used for the same thing, the total number of DDR
controllers for a given SoC. Use SYS_NUM_DDR_CTRLS in Kconfig and
merge existing usage.
York Sun [Wed, 28 Dec 2016 16:43:44 +0000 (08:43 -0800)]
ddr: fsl: Move macro CONFIG_NUM_DDR_CONTROLLERS to Kconfig
Use option NUM_DDR_CONTROLLERS in ddr Kconfig and clean up existing
usage in ls102xa and fsl-layerscape. Remove all powerpc macros in
config header and board header files.
York Sun [Wed, 28 Dec 2016 16:43:42 +0000 (08:43 -0800)]
mmc: move CONFIG_SYS_FSL_ERRATUM_ESDHC* to Kconfig
Add option SYS_FSL_ERRATUM_ESDHC111, SYS_FSL_ERRATUM_ESDHC13,
SYS_FSL_ERRATUM_ESDHC135, SYS_FSL_ERRATUM_ESDHC_A001 to mmc Kconfig.
Move existing macros to related Kconfig.
Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Migrate bk4r1] Signed-off-by: Tom Rini <trini@konsulko.com>
York Sun [Wed, 28 Dec 2016 16:43:40 +0000 (08:43 -0800)]
fsl_ddr: Move DDR config options to driver Kconfig
Create driver/ddr/fsl/Kconfig and move existing options. Clean up
existing macros.
Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Migrate sbc8641d, xpedite537x and MPC8536DS, run a moveconfig.py -s] Signed-off-by: Tom Rini <trini@konsulko.com>
Vignesh R [Wed, 21 Dec 2016 05:12:33 +0000 (10:42 +0530)]
spi: cadence_qspi_apb: Use 32 bit indirect read transaction when possible
According to Section 11.15.4.9.1 Indirect Read Controller of K2G SoC
TRM SPRUHY8D[1], the external master is only permitted to issue 32-bit
data interface reads until the last word of an indirect transfer
So, make sure that QSPI indirect reads are 32 bit sized except for the
final read. If the rxbuf is unaligned then use bounce buffer, so that
readsl() can be used instead of readsb() to avoid non 32-bit accesses.
[1]www.ti.com/lit/ug/spruhy8d/spruhy8d.pdf
Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Jagan Teki <jagan@openedev.com>
Vignesh R [Wed, 21 Dec 2016 05:12:32 +0000 (10:42 +0530)]
spi: cadence_qspi_apb: Use 32 bit indirect write transaction when possible
According to Section 11.15.4.9.2 Indirect Write Controller of K2G SoC
TRM SPRUHY8D[1], the external master is only permitted to issue 32-bit
data interface writes until the last word of an indirect transfer
otherwise indirect writes is known to fails sometimes. So, make sure
that QSPI indirect writes are 32 bit sized except for the last write. If
the txbuf is unaligned then use bounce buffer to avoid data aborts.
So, now that the driver uses bounce_buffer, enable CONFIG_BOUNCE_BUFFER
for all boards that use Cadence QSPI driver.
[1]www.ti.com/lit/ug/spruhy8d/spruhy8d.pdf
Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Jagan Teki <jagan@openedev.com>
Andre Przywara [Mon, 2 Jan 2017 11:48:45 +0000 (11:48 +0000)]
sunxi: A64: enable SPL
Now that the SPL is ready to be compiled in AArch64 and the DRAM
init code is ready, enable SPL support for the A64 SoC and in the
Pine64 defconfig.
For now we keep the boot0 header in the U-Boot proper, as this allows
to still use boot0 as an SPL replacement without hurting the SPL use
case.
We disable FEL support for now by making its compilation conditional
and disabling it for ARM64, as the code isn't ready yet.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jagan@openedev.com>
Andre Przywara [Mon, 2 Jan 2017 11:48:44 +0000 (11:48 +0000)]
sunxi: DRAM: fix H3 DRAM size display on aarch64
Fix the output of the DRAM size on AArch64 SPLs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Alexander Graf <agraf@suse.de> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Jens Kuske [Mon, 2 Jan 2017 11:48:42 +0000 (11:48 +0000)]
sunxi: A64: use H3 DRAM initialization code for A64 as well
The A64 DRAM controller is very similar to the H3 one,
so the code can be reused with some small changes.
This refactoring does not change the code size for the existing H3 part.
[Andre: rework from #ifdefs to using socid parameters in static
functions, minor fixes, merging in fixes from Jens]
Signed-off-by: Jens Kuske <jenskuske@gmail.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Philipp Tomsich [Mon, 2 Jan 2017 11:48:41 +0000 (11:48 +0000)]
sunxi: clocks: Use the correct pattern register for PLL11
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
projects / u-boot.git / log
