Ajay Kumar [Thu, 21 Feb 2013 23:52:59 +0000 (23:52 +0000)]
video: exynos_fb: Make fimd_ctrl global
fimd_ctrl variable was redundantly defined across all the functions in
the driver even though it contains just the same address. We make it
global and initialize it in exynos_fimd_lcd_init. From then on, other
funtions can use the data in the global variable.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Ajay Kumar [Thu, 21 Feb 2013 23:52:58 +0000 (23:52 +0000)]
video: exynos_dp: Remove callbacks from the driver
Replaced the functionality of callbacks by using a standard set of functions.
Instead of implementing and hooking up a callback, put the same code in one of
the standard set of functions by overriding it.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Ajay Kumar [Thu, 21 Feb 2013 23:52:57 +0000 (23:52 +0000)]
video: exynos_fb: Remove callbacks from the driver
Replaced the functionality of callbacks by using a standard set of functions.
Instead of implementing and hooking up a callback, put the same code in one of
the standard set of functions by overriding it.
This patch is tested only on SMDK5250.
For Trats and universal_c210 board, it is only compile tested.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Tom Warren [Mon, 18 Mar 2013 21:52:26 +0000 (14:52 -0700)]
Tegra114: MMC: Enable DT MMC driver support for Tegra114 Dalmore boards
Tested on my Dalmore E1611 board, eMMC and SD-Card work fine, can load
a kernel off of an SD card OK, card detect works, and the env is now
stored in eMMC (end of the 2nd 'boot' sector, same as Tegra20/30).
Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
Allen Martin [Sat, 16 Mar 2013 18:58:07 +0000 (18:58 +0000)]
spi: add common fdt SPI driver interface
Add a common interface to fdt based SPI drivers. Each driver is
represented by a table entry in fdt_spi_drivers[]. If there are
multiple SPI drivers in the table, the first driver to return success
from spi_init() will be registered as the SPI driver.
Signed-off-by: Allen Martin <amartin@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
Allen Martin [Sat, 16 Mar 2013 18:58:02 +0000 (18:58 +0000)]
tegra: remove support for UART SPI switch
This feature was only used for tegra20 seaboard that had a pinmux
conflict on the SPI pins. These boards were never manufactured, so
remove this support to clean up SPI driver.
Signed-off-by: Allen Martin <amartin@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
Peter Korsgaard [Thu, 21 Mar 2013 04:00:03 +0000 (04:00 +0000)]
mmc: mmc_getcd/getwp: use sensible defaults
Let mmc_getcd() return true and mmc_getwp() false if mmc driver doesn't
provide handlers for them.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
[trini: Add braces around first if test in each case to fix warning] Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Matt Porter <mporter@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
[trini: Adapt to recent omap_hsmmc requirements, Matt re-tested] Signed-off-by: Tom Rini <trini@ti.com>
Matt Porter [Fri, 15 Mar 2013 10:07:05 +0000 (10:07 +0000)]
am33xx: refactor am33xx mux support and add ti814x support
AM33XX and TI814X have a similar mux though the pinmux register
layout and address space differ. Add a separate ti814x mux include
to support the TI814X-specific differences.
Signed-off-by: Matt Porter <mporter@ti.com> Reviewed-by: Tom Rini <trini@ti.com> Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Matt Porter [Fri, 15 Mar 2013 10:07:03 +0000 (10:07 +0000)]
am33xx: refactor emif4/ddr to support multiple EMIF instances
The AM33xx emif4/ddr support closely matches what is need to support
TI814x except that TI814x has two EMIF instances. Refactor all the
emif4 helper calls and the config_ddr() init function to use an
additional instance number argument.
Signed-off-by: Matt Porter <mporter@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
Tom Rini [Thu, 14 Mar 2013 11:15:25 +0000 (11:15 +0000)]
am33xx: Add required includes to some omap/am33xx code
- In arch/arm/cpu/armv7/omap-common/timer.c,
drivers/mtd/nand/omap_gpmc.c and drivers/net/cpsw.c add #include files
that the driver needs but had been relying on <config.h> to bring in.
- In arch/arm/cpu/armv7/omap-common/lowlevel_init.S add <config.h>
- In am335x_evm.h and pcm051.h don't globally include
<asm/arch/hardware.h> and <asm/arch/cpu.h> but just <asm/arch/omap.h>
as that is the only include which defines things the config uses.
Cc: Lars Poeschel <poeschel@lemonage.de> Signed-off-by: Tom Rini <trini@ti.com>
With v3.9 and later of the Linux Kernel defaulting to multi-platform
images with omap2plus_defconfig, uImage isn't builtable anymore by
default. Add CONFIG_CMD_BOOTZ so that we can still boot something the
kernel spits out.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Steve Kipisz [Fri, 8 Mar 2013 07:40:58 +0000 (07:40 +0000)]
am33xx:ddr:Fix config_sdram to work for all DDR
The original write to sdram_config is correct for DDR3 but incorrect
for DDR2 so SPL was hanging. For DDR2, the write to sdram_config
should be after the writes to ref_ctrl. This was working for DDR3
because there was a write of 0x2800 to ref_ctrl before a write
to sdram_config.
Tested on: GP EVM 1.1A (DDR2), GP EVM 1.5A (DDR3),
Beaglebone A6 (DDR2), Beagleone Blacd A4A (DDR3)
Koen Kooi [Thu, 14 Mar 2013 05:55:21 +0000 (05:55 +0000)]
am335x_evm: Add more variables and switch to DT booting.
Make bootcmd run findfdt so that we know what dtb file to load. Add a
loadfdt command to load this file in. Make mmcboot pass in ${fdtaddr}
and make the mmc section of bootcmd run loadfdt.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Koen Kooi [Thu, 14 Mar 2013 05:55:20 +0000 (05:55 +0000)]
am335x_evm: Enable CMD_EXT4 and CMD_FS_GENERIC, add bootpart to env
The kernel is loaded from some form of ext[234] or FAT, depending on the
distribution used. We add a bootpart variable to the environment so
that we can load from the correct mmc partition as well. We leave
CONFIG_CMD_EXT2 for existing scripts that use ext2load.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Stephen Warren [Tue, 29 Jan 2013 16:37:42 +0000 (16:37 +0000)]
ARM: rpi_b: enable SD controller, add related env/cmds
Enable the SD controller driver for the Raspberry Pi. Enable a number
of useful MMC, partition, and filesystem-related commands. Set up the
environment to provide standard locations for loading a kernel, DTB,
etc. Provide a boot command that loads and executes boot.scr.uimg from
the SD card; this is written considering future extensibilty to USB
storage.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Stephen Warren [Tue, 29 Jan 2013 16:37:41 +0000 (16:37 +0000)]
mmc: add bcm2835 driver
This adds a simple driver for the BCM2835's SD controller.
Workarounds are implemented for:
* Register writes can't be too close to each-other in time, or they will
be lost.
* Register accesses must all be 32-bit, so implement custom accessors.
This code was extracted from:
git://github.com/gonzoua/u-boot-pi.git master
which was created by Oleksandr Tymoshenko.
Portions of the code there were obviously based on the Linux kernel at:
git://github.com/raspberrypi/linux.git rpi-3.6.y
commit f5b930b "Main bcm2708 linux port" signed-off-by Dom Cobley.
swarren changed the following for upstream:
* Removed hack udelay()s in bcm2835_sdhci_raw_writel(); setting
SDHCI_QUIRK_WAIT_SEND_CMD appears to solve the issues.
* Remove register logging from read*/write* functions.
* Sort out confusion with min/max_freq values passed to add_sdhci().
* Use more descriptive variable names and calculations in IO accessors.
* Simplified and commented twoticks_delay calculation.
* checkpatch fixes.
Cc: Andy Fleming <afleming@gmail.com> Signed-off-by: Oleksandr Tymoshenko <gonzo@bluezbox.com> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Acked-by: Andy Fleming <afleming@gmail.com>
Stephen Warren [Tue, 29 Jan 2013 16:37:40 +0000 (16:37 +0000)]
video: add a driver for the bcm2835
The firmware running on the bcm2835 SoC's VideoCore CPU manages the
display controller. Add a simple "LCD" driver that communicates with the
firmware using the property mailbox protocol. This configures the
display and frame-buffer to match whatever physical resolution the
firmware chosen when booting, which is typically the native resolution
of the attached display device, presumably unless otherwise specified
in config.txt on the boot media.
Enable this driver in the Raspberry Pi board configuration.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Acked-by: Anatolij Gustschin <agust@denx.de>
Stephen Warren [Tue, 29 Jan 2013 16:37:39 +0000 (16:37 +0000)]
ARM: rpi_b: disable rpi_b dcache explicitly
There appears to be no implementation of flush_dcache_range() for
ARM1176, so explicitly disable dcache support to avoid references to
that function from the LCD core in the next patch. This was presumably
not noticed before simply because no drivers for the rpi_b were
attempting DMA.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Stephen Warren [Tue, 29 Jan 2013 16:37:38 +0000 (16:37 +0000)]
lcd: calculate line_length after lcd_ctrl_init()
When an LCD driver is actually driving a regular external display, e.g.
an HDMI monitor, the display resolution might not be known until the
display controller has initialized, i.e. during lcd_ctrl_init(). However,
lcd.c calculates lcd_line_length before calling this function, thus
relying on a hard-coded resolution in struct panel_info.
Instead, defer this calculation until after lcd_ctrl_init() has had the
chance to dynamically determine the resolution. This needs to happen
before lcd_clear(), since the value is used there.
grep indicates that no code outside lcd.c uses this lcd_line_length; in
particular, no lcd_ctrl_init() implementations read it.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Acked-by: Anatolij Gustschin <agust@denx.de>
Stephen Warren [Tue, 29 Jan 2013 16:37:37 +0000 (16:37 +0000)]
ARM: rpi_b: use bcm2835 mbox driver to get memory size
The firmware running on the bcm2835 SoC's VideoCore CPU determines how
much of the system RAM is available for use by the ARM CPU. Previously,
U-Boot assumed that only 128MB was available, since this was the
smallest value configured by any public firmware. However, we can now
query the actual value at run-time from the firmware using the mbox
property protocol.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Stephen Warren [Tue, 29 Jan 2013 16:37:36 +0000 (16:37 +0000)]
ARM: bcm2835: add mailbox driver
The BCM2835 SoC contains (at least) two CPUs; the VideoCore (a/k/a "GPU")
and the ARM CPU. The ARM CPU is often thought of as the main CPU.
However, the VideoCore actually controls the initial SoC boot, and hides
much of the hardware behind a protocol. This protocol is transported
using the SoC's mailbox hardware module.
Here, we add a very simplistic driver for the mailbox module, and define
a few structures for the property messages.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Tom Rini [Mon, 18 Mar 2013 16:31:00 +0000 (12:31 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
Albert's rework of the linker scripts conflicted with Simon's making
everyone use __bss_end. We also had a minor conflict over
README.scrapyard being added to in mainline and enhanced in
u-boot-arm/master with proper formatting.
Michael Spang [Wed, 6 Mar 2013 14:08:33 +0000 (14:08 +0000)]
usb: usbeth: smsc95xx: remove EEPROM loaded check
[port of Linux kernel commit bcd218be5aeb by Steve Glendinning]
The eeprom read & write commands currently check the E2P_CMD_LOADED_ bit is
set before allowing any operations. This prevents any reading or writing
unless a correctly programmed EEPROM is installed.
Signed-off-by: Michael Spang <spang@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Marek Vasut <marex@denx.de>
Vincent Palatin [Wed, 6 Mar 2013 14:08:32 +0000 (14:08 +0000)]
usb: ehci: Fix aliasing issue in EHCI interrupt code
The interrupt endpoint handling code stores the buffer pointer in the QH
padding field. We need to make it the size of a pointer to avoid strict
aliasing issue with the compiler.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Patrick Georgi [Wed, 6 Mar 2013 14:08:31 +0000 (14:08 +0000)]
usb: ehci: Support interrupt transfers via periodic list
Interrupt transfers aren't meant to be used from the async list
(the EHCI spec indicates trouble with low/full-speed intr on async).
Build a periodic list instead, and provide an API to make use of it.
Then, use that API from the existing interrupt transfer API.
This provides support for USB keyboards using EHCI.
Use timeouts to ensure we cannot get stuck in the keyboard scanning
if something wrong happens (USB device unplugged or fatal I/O error)
Signed-off-by: Vincent Palatin <vpalatin@chromium.org> Signed-off-by: Julius Werner <jwerner@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Vivek Gautam [Wed, 6 Mar 2013 08:48:32 +0000 (14:18 +0530)]
usb: ehci: exynos: Fix multiple FDT decode
With current FDT support driver tries to parse device node
twice in ehci_hcd_init() and ehci_hcd_stop(), which shouldn't
happen ideally.
Making provision to store data in a global structure and thereby
passing its pointer when needed.
Lukasz Majewski [Tue, 5 Mar 2013 11:10:17 +0000 (12:10 +0100)]
usb:gadget: USB Mass Storage Gadget support
This patch adds the USB Mass Storage Gadget to u-boot
New command called "ums" is implemented to provide access
to on-device embedded persistent memory.
USB Mass Storage is supposed to work on top of the USB
Gadget framework
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> CC: Marek Vasut <marek.vasut@gmail.com>
Lukasz Majewski [Fri, 1 Mar 2013 14:30:18 +0000 (15:30 +0100)]
usb:composite:fix Provide function data when addressing device with only one interface
This commit fixes problems with some non-standard requests send with
device address instead of interface address (bmRequestType.Receipent field).
This happens with dfu-util (debian version: 0.5), which address non standard
requests (like w_value=0x21 and bRequest=GET_DESCRIPTOR) to device.
Without this fix, the above request is STALLED, and hence causes dfu-util
to assume some standard configuration (packet size = 1024B instead of 4096B)
In turn it displays following errors:
Error obtaining DFU functional descriptor
Warning: Assuming DFU version 1.0
Warning: Transfer size can not be detected
...
Warning: Trying default transfer size 1024
This fix allows passing non-standard request to function setup code, where
it shall be handled.
Tested at: Trats (exynos4210)
Tested with:DFU and UMS gadgets
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Simon Glass [Tue, 5 Mar 2013 14:40:04 +0000 (14:40 +0000)]
sparc: Fix build warnings in serial.c
These macros are already defined in io.h so should not be declared in
serial.c.
serial.c:38:0: warning: "READ_BYTE" redefined
/home/sjg/c/src/third_party/u-boot/files/include/asm/io.h:36:0: note: this is the location of the previous definition
serial.c:39:0: warning: "READ_HWORD" redefined
/home/sjg/c/src/third_party/u-boot/files/include/asm/io.h:37:0: note: this is the location of the previous definition
serial.c:40:0: warning: "READ_WORD" redefined
/home/sjg/c/src/third_party/u-boot/files/include/asm/io.h:38:0: note: this is the location of the previous definition
serial.c:41:0: warning: "READ_DWORD" redefined
/home/sjg/c/src/third_party/u-boot/files/include/asm/io.h:39:0: note: this is the location of the previous definition
Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 5 Mar 2013 14:40:03 +0000 (14:40 +0000)]
sparc: Fix out-of-tree building
It isn't clear why the sparc cpu Makefile has its own compile line, but
it does not work correctly with an out-of-tree build. Removing it fixes
this problem. Perhaps it does not introduce others.
Simon Glass [Tue, 5 Mar 2013 14:39:52 +0000 (14:39 +0000)]
x86: Adjust board_f.c for x86
For x86, things have adjusted somewhat since this series was originally
written. It has its own way of running through initcalls which is actually
nicer than others archs.
Unfortunately this does introduce exceptions. We will soon require use of
generic board on x86, but until then we need to fit in with what is there,
and treat x86 as a special case.
Simon Glass [Mon, 11 Mar 2013 07:06:48 +0000 (07:06 +0000)]
Add CONFIG_SYS_SYM_OFFSETS to support offset symbols
Link symbols as created by the link script can either be absolute or
relative to the text start. This option switches between the two options
so that we can support both.
As we convert architectures over to generic board, we can see if this
option is actually needed, or whether it is possible to unify this feature
also.
projects / u-boot.git / log
