Marek Vasut [Sat, 12 Sep 2020 23:35:08 +0000 (01:35 +0200)]
ARM: mx6: ddr: Add support for iMX6UL/ULL/SL/SDL
This patch adds support for iMX6UL/ULL/SL/SDL MMDC into the DDR calibration
code. The difference between MX6DQ and MX6UL/ULL/SL is that the later SoCs
have 2 SDQS registers, just like MX6SX, while the MX6DQ/MX6SDL has 8.
Fixes: 4f4c128c65 ("ARM: mx6: ddr: Add support for iMX6SX") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Eric Nelson <eric@nelint.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Fabio Estevam <festevam@gmail.com>
The size of the binary created with the default U-boot config is much
greater than the default offset for environment `0x60000`.
In case if that binary is used for booting via MMC it is overlapped with
the environment stored on MMC.
This leads to U-Boot corruption while saving environment with `saveenv`
command and non-bootable SabreLite board.
The offset for environment `CONFIG_ENV_OFFSET=0x60000` was added in
commit a09fea1 but did not count in the change to `0xC0000` if option
`CONFIG_ENV_IS_IN_MMC` is used.
The offset is also used for variant with environment saving onto SPI NOR
flash (with enabled option `CONFIG_ENV_IS_IN_SPI_FLASH`). In that case the
U-Boot binary flashed on SPI NOR is also corrupted after environment
saving with the original 0x60000 offset.
Signed-off-by: Denis Pynkin <denis.pynkin@collabora.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Peng Fan [Wed, 16 Sep 2020 07:17:18 +0000 (15:17 +0800)]
imx7: ccm: correct target interface num
According to i.MX 7Dual Applications Processor Reference Manual, Rev. 1
The target interface CCM root index ranges [0,124], so the number
should be 125.
Reported-by: Coverity 18045 Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com>
Igor Opaniuk [Mon, 14 Sep 2020 08:01:10 +0000 (11:01 +0300)]
colibri_imx7: use preboot for fdtfile evaluation
Enable and set preboot var with fdtfile evaluation.
preboot will be checked and run immediately before starting the
CONFIG_BOOTDELAY countdown and/or running the auto-boot command resp.
entering interactive mode.
This provides possibility to use different boot cmds in interactive mode
without manual setting fdtfile value, as it it's already evaluated
before entering interactive mode.
Igor Opaniuk [Mon, 14 Sep 2020 08:01:09 +0000 (11:01 +0300)]
colibri_vf: use preboot for fdtfile evaluation
Enable and set preboot var with fdtfile evaluation.
preboot will be checked and run immediately before starting the
CONFIG_BOOTDELAY countdown and/or running the auto-boot command resp.
entering interactive mode.
This provides possibility to use different boot cmds in interactive mode
without manual setting fdtfile value, as it it's already evaluated
before entering interactive mode.
Fixes: 304042c1f3("colibri_vf: set fdtfile for distroboot") Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Igor Opaniuk [Mon, 14 Sep 2020 08:01:08 +0000 (11:01 +0300)]
colibri-imx6ull: use preboot for fdtfile evaluation
Enable and set preboot var with fdtfile evaluation.
preboot will be checked and run immediately before starting the
CONFIG_BOOTDELAY countdown and/or running the auto-boot command resp.
entering interactive mode.
This provides possibility to use different boot cmds in interactive mode
without manual setting fdtfile value, as it it's already evaluated
before entering interactive mode.
Tom Rini [Wed, 16 Sep 2020 12:08:06 +0000 (08:08 -0400)]
Merge tag 'efi-2020-10-rc5' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-10-rc5
The following bugs are fixed:
* unaligned access in br_i32_decode()
* missing restore of global data pointer in UEFI selftest
* missing restore of global data pointer on RISC-V in UEfI subsystem
* efi_var_mem_notify_exit_boot_services() should not be __efi_runtime
The linker sometimes creates PT_LOAD segments with length (p_filesz) zero
as described in https://man7.org/linux/man-pages/man5/elf.5.html. This
leads to build failures. We should ignore empty segments.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Tested-by: Tom Rini <trini@konsulko.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Mon, 13 Apr 2020 01:38:30 +0000 (09:38 +0800)]
rockchip: rv1108: use correct API for board callback
Use board_early_init_f() instead of mach_cpu_init() for board, the
board_early_init_f() is used for board init and after dm_initf, while
the mach_cpu_init() is used for CPU/SOC and before dm_initf()(not able
to use syscon API).
Fixes: 9cec336708 ("rockchip: evb-rv1108: Use syscon API to get grf base") Fixes: 4aa33690fc {"rockchip: elgin-rv1108: Use syscon API to get grf base") Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
mmc: msm_sdhci: Use mmc_of_parse for setting host_caps
Since the introduction of 'get_cd' callback in sdhci core,
dragonboard410c's MMC interface is broken. It turns out that 'get_cd'
callback checks for the host_caps for validating the chip select. And
since the msm_sdhci driver is not parsing the host_caps from DT, not
all of the cababilities are parsed properly. This results in the MMC
interfaces to be broken.
Hence, fix this by adding a call to 'mmc_of_parse' during driver probe.
efi_var_mem_notify_exit_boot_services() is invoked when ExitBootServices()
is called by the UEFI payload.
efi_var_mem_notify_exit_boot_services() should not be defined as
__efi_runtime as it is invoking EFI_ENTRY() and EFI_EXIT() which themselves
are not __efi_runtime.
Fixes: f1f990a8c958 ("efi_loader: memory buffer for variables") Fixes: e01aed47d6a0 ("efi_loader: Enable run-time variable support for tee based variables") Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Robert Reither [Mon, 14 Sep 2020 11:12:02 +0000 (13:12 +0200)]
rsa: crash in br_i32_decode() called from rsa_gen_key_prop()
Fixes problem for unaligned 32bit big-endian access in
lib/rsa/rsa-keyprop.c.
Exchanges br_i32_decode() with get_unaligned_be32().
This will keep the unaligned access for architectures capable and will do
some byte-shift magic for the not so capable ones.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-by: Robert Reither <robert.reither@external.thalesgroup.com>
Remove unused include. Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
test: do no assume hush parser in validate_empty()
The environment variable test uses function validate_empty() to check that
a variable is not defined. If the hush parser is not enabled, we cannot
refer to a variable by $var_name but only by ${var_name}.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Acked-by: Stephen Warren <swarren@nvidia.com>
Attempting to place device tree immediately after an image in memory can lead
to mis-aligned data accesses if that image size is not divisible by the
alignment requirements of the architecture.
Data aborts caused by this were observed on a custom Marvel A388 based system,
where the image was a uboot FIT file. The total size varies depending on the
uboot device tree size, which does not always lead to correct alignment.
The minimum alignment specified for ARM [1] and ARM64 [2] linux booting has been
used
T Karthik Reddy [Mon, 31 Aug 2020 12:27:37 +0000 (14:27 +0200)]
mtd: nand: Fix nand write error with bad block addresses above 32-bit
Nand writes should skip the bad blocks with "nand write" command.
In case of bad blocks with above 32-bit address, nand_block_isbad()
returns false due to truncated bad block address.
In below code segment,
if (nand_block_isbad(mtd, offset & ~(mtd->erasesize - 1)))
offset is 64-bit and mtd->erasesize is 32-bit, hence the truncation is
happening. Cast 'mtd->erasesize' with loff_t to fix this issue.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Pedro Aguilar [Mon, 31 Aug 2020 09:01:41 +0000 (11:01 +0200)]
env: Crash in 'env import' when using checksum and a specific size
This patch adds a sanity check that avoids 'size' to overflow and crash when
importing an environment that contains a checksum. Example with the wrong size
that causes the crash:
=> env import -c 0x4100000 3 v1
This assumes that v1 has already been successfully exported with
'env export -c -s 0x100 0x4100000 v1'
Signed-off-by: Pedro Aguilar <pedro.aguilar@vimar.com>
bootm: update image OS image size when decompressing
In bootm_load_os() the OS image is decompressed. In later stages of the
boot process we need the decompressed size of the image.
Update images->os.image_len after decompression.
Passing the correct size is necessary if we want to check loaded EFI
binararies for file truncation by comparing the loaded size to the header
field SizeOfImage.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Michal Simek [Thu, 27 Aug 2020 16:01:28 +0000 (18:01 +0200)]
common: Kconfig: Add dependency for default variables strings
Kconfig provides several config options for setting up default variables
but these are unused when variables are passed to U-Boot via file.
That's why cover this dependency in Kconfig.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Chuanjia Liu [Mon, 31 Aug 2020 07:53:12 +0000 (15:53 +0800)]
PCI: mediatek: Release the resource when PCIe enable port fail
On the mt7623 platform, if one port enable fail and other port
enable succeed. It will hang on when using pci enum
because the resource was not released correctly.
Signed-off-by: Chuanjia Liu <Chuanjia.Liu@mediatek.com> Tested-by: Frank Wunderlich <frank-w@public-files.de>
Marek Vasut [Sat, 22 Aug 2020 20:45:25 +0000 (22:45 +0200)]
ARM: dts: stm32: Adjust PLL4 settings on AV96 again
PLL4Q is supplying both FDCAN and LTDC. In case HDMI is in use, the
50 MHz generated from PLL4Q cannot be divided well enough to produce
accurate clock for HDMI pixel clock. Adjust it to generate 74.25 MHz
instead. The PLL4P/PLL4R are generating 99 MHz instead of 100 MHz,
which is in tolerance for the SDMMC.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Gerald Baeza <gerald.baeza@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Marek Vasut [Sat, 22 Aug 2020 20:45:36 +0000 (22:45 +0200)]
ARM: dts: stm32: Pull UART4 RX high on AV96
There is no dedicated pull resistor on the AV96 UART4 (console UART)
pin. In case there is no UART adapter installed on the AV96, the line
is floating and can trigger reception of garbage characters, which in
turn can abort U-Boot autoboot. Add default pull up to mitigate this
problem.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
arm: stm32mp: cleanup test on eth_env_set_enetaddr result
Remove the unnecessary inversion on the eth_env_set_enetaddr() result which
only make complex the code of setup_mac_address() and display an invalid
value in the associated pr_err.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Marek Vasut <marex@denx.de>
config: Enable USB Keyboard suuport on RPi4 32 bit
Supporting USB keyboards out of the box is both handy for development
and production. Notably if u-boot is used to boot into GRUB. This patch
adds USB keyboard support for 32 bit RPi4 config.
Jason Wessel [Fri, 17 Jul 2020 13:32:00 +0000 (06:32 -0700)]
bcmgenet: Add support for rgmii-rxid
The commit 57805f2270c4 ("net: bcmgenet: Don't set ID_MODE_DIS when
not using RGMII") needed to be extended for the case of using the
rgmii-rxid. The latest version of the Rasbperry Pi4 dtb files for the
5.4 now specify the rgmii-rxid.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Tested-by: Petr Tesarik <ptesarik@suse.com> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Jason Wessel [Fri, 17 Jul 2020 13:31:59 +0000 (06:31 -0700)]
bcmgenet: fix DMA buffer management
This commit fixes a serious issue occurring when several network
commands are run on a raspberry pi 4 board: for instance a "dhcp"
command and then one or several "tftp" commands. In this case,
packet recv callbacks were called several times on the same packets,
and send function was failing most of the time.
note: if the boot procedure is made of a single network
command, the issue is not visible.
The issue is related to management of the packet ring buffers
(producer / consumer) and DMA.
Each time a packet is received, the ethernet device stores it
in the buffer and increments an index called RDMA_PROD_INDEX.
Each time the driver outputs a received packet, it increments
another index called RDMA_CONS_INDEX.
Between each pair of network commands, as part of the driver
'start' function, previous code tried to reset both RDMA_CONS_INDEX
and RDMA_PROD_INDEX to 0. But RDMA_PROD_INDEX cannot be written from
driver side, thus its value was actually not updated, and only
RDMA_CONS_INDEX was reset to 0. This was resulting in a major
synchronization issue between the driver and the device. Most
visible behavior was that the driver seemed to receive again the
packets from the previous commands (e.g. DHCP response packets
"received" again when performing the first TFTP command).
This fix consists in setting RDMA_CONS_INDEX to the same
value as RDMA_PROD_INDEX, when resetting the driver.
The same kind of fix was needed on the TX side, and a few variables
had to be reset accordingly (c_index, tx_index, rx_index).
The rx_index and tx_index have only 256 entries so the bottom 8 bits
must be masked off.
Originated-by: Etienne Dublé <etienne.duble@imag.fr> Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Tested-by: Petr Tesarik <ptesarik@suse.com> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Tom Rini [Mon, 7 Sep 2020 12:49:50 +0000 (08:49 -0400)]
Merge tag 'efi-2020-10-rc4' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-10-rc4
Bug fixes are provided in the following areas:
* convert file system debug and print messages go log messages
* convert UEFI booting messages to log messages
* UEFI related code clean up and simplification
* Eliminate superfluous enum value EFI_TABLE_END.
* Use correct variable type for the memory type.
* Check validity of memory type.
* Make efi_build_mem_table static.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
defconfig: espressobin: Add support for ISSI SPI flashes
Enable support of ISSI SPI flashes found on EspressoBIN boards
Change-Id: I6de61c48f108fb4f410f321b9db45887d23212e5 Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/61455 Tested-by: iSoC Platform CI <ykjenk@marvell.com> Reviewed-by: Grzegorz Jaszczyk <jaz@semihalf.com> Reviewed-by: Stefan Chulski <stefanc@marvell.com> Reviewed-by: Stefan Roese <sr@denx.de>
zachary [Fri, 28 Aug 2020 14:56:29 +0000 (16:56 +0200)]
phy: marvell: a3700: add sata comphy on lane 2 with invert option
- This patch moves sata phy powerup from dedicate phy to compphy
and adds invert option for sata powerup routine.
Change-Id: I1b4e8753e2b2c14c6efa97bca2ffc7d2553d8a90 Signed-off-by: zachary <zhangzg@marvell.com> Signed-off-by: Ken Ma <make@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/53601 Reviewed-by: Igal Liberman <igall@marvell.com> Tested-by: Igal Liberman <igall@marvell.com>
[a.heider: adapt to mainline] Signed-off-by: Andre Heider <a.heider@gmail.com> Tested-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Chee Hong Ang [Thu, 6 Aug 2020 03:56:29 +0000 (11:56 +0800)]
arm: socfpga: soc64: Check FPGA Config status register before bridge reset
Instead of querying SDM for FPGA configuration status through mailbox
messages, U-Boot now checks System Manager's FPGA Config status register
for FPGA configuration status before resetting bridge.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com> Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Gary Bisson [Thu, 27 Aug 2020 08:51:14 +0000 (10:51 +0200)]
fastboot: getvar: fix partition-size return value
The size returned by 'getvar partition-size' should be in bytes, not in
blocks as fastboot uses that value to generate empty partition when
running format [1].
Note that the function was already returning the proper size in bytes
for NAND devices (see struct part_info details).
yurii.pidhornyi [Thu, 20 Aug 2020 15:41:18 +0000 (18:41 +0300)]
fastboot: Fix fastboot reboot fail by changing functions order
It was revealed that when the fastboot_tx_write_str function is called
without the previously initialized fastboot_func->in_req->complete field,
a copy of in_req will be sent to the I/O requests queue without
an initialized field.
Moving a piece of code with the initializing of the
fastboot_func->in_req->complete field above transmit_tx allows to solve
this problem.
Fixes: 65c96757fe9 "usb: fastboot: Convert USB f_fastboot to shared fastboot" Signed-off-by: yurii.pidhornyi <yurii.pidhornyi@globallogic.com>
Sherry Sun [Tue, 18 Aug 2020 10:16:49 +0000 (18:16 +0800)]
f_sdp: Change bInterval of interrupt endpoint to 3
Since the USB HID limits the maximum bandwidth(3072) for interrupt
endpoint transfers, when the bInterval set to 1, we can only support 3
boards to run sdp at the same time. In order to support more boards,
change the bInterval of interrupt endpoint to 3, which will not affect
the transmission speed.
Reviewed-by: Ye Li <ye.li@nxp.com> Signed-off-by: Sherry Sun <sherry.sun@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Sherry Sun [Tue, 18 Aug 2020 10:16:48 +0000 (18:16 +0800)]
f_sdp: Add EP1_OUT as default data receive pipe in sdp
EP0 has been used to transfer file data in sdp before, but the max
packetsize of ep0 is 64 bytes. So in order to improve the file transfer
speed, here add the EP1_OUT interrupt endpoint which max packetsize is
set to 1024 byte.
After testing, it turns out that using ep1out is twice as fast as using
ep0 while receiving data in sdp.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Tue, 18 Aug 2020 10:16:46 +0000 (18:16 +0800)]
f_sdp: Support searching and loading FIT or container image
Add support to f_sdp to search and load iMX8 container image or iMX8M
FIT image by new UUU command SDPV.
When using the SDPV, the uuu will continue to send out data after first
level boot loader used by ROM. This means uuu won't skip to the offset
of the second boot loader, and the padding data before second boot loader
will be sent out. So we have to search the FIT header or container header
in the buffer that SDP received.
Also change to more common method to exit f_sdp handler not depending on
SPL_FIT_FOUND flag because container loader won't set this.
MAX3420 implements FullSpeed USB Device over SPI.
Another version MAX3421, also implements USB Host mode.
This driver should be good for the device mode of max3421 as well.
Default implementation of fastboot_set_reboot_flag function that depends
on "bcb" commands could be used in general case if there are no need to
make any platform-specific implementation, otherwise it could be
disabled via Kconfig option FASTBOOT_USE_BCB_SET_REBOOT_FLAG.
Please note that FASTBOOT_USE_BCB_SET_REBOOT_FLAG is mutually exclusive
with some platforms which already have their own implementation of this
function.
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
fastboot: Add support for 'reboot fastboot' command
Android 10 adds support for dynamic partitions and in order to support
this userspace fastboot must be used[1]. New tool fastbootd is
included into recovery.
Userspace fastboot works from recovery and is launched if:
1) - Dynamic partitioning is enabled
2) - Boot control block has 'boot-fastboot' value into command field
The bootloader is expected to load and boot into the recovery image
upon seeing boot-fastboot in the BCB command. Recovery then parses the
BCB message and switches to fastbootd mode[2].
Please note that boot script is expected to handle 'boot-fastboot'
command in BCB and load into recovery mode.
Bootloader must support 'reboot fastboot' command which should reboot
device into userspace fastboot to accomodate those changes[3].
Another command that bootloader must support[3] is 'reboot recovery'. This
command should simply reboot device into recovery mode.
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com> Signed-off-by: Roman Stratiienko <r.stratiienko@gmail.com>
Change-Id: I9d2bdc9a6f6f31ea98572fe155e1cc8341e9af76
The environment variable loadaddr is in the virtual address space of the
sandbox. To get the actual memory address where the FIT image has been
loaded we have to convert this address according to the memory mapping of
the sandbox.
Equally the addresses in the *.its file have to be converted when used in
the dfu_ram driver.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Filip Brozovic [Mon, 29 Jun 2020 11:14:37 +0000 (13:14 +0200)]
fastboot: Support defining raw partitions without a partition table
Add support for defining raw fastboot partitions in eMMC by specifying
the offset and size in an environment variable. Optionally, the eMMC
hardware partition number may also be specified.
This makes it possible to e.g. update only part of the eMMC boot
partition, instead of having to write the entire partition.
Signed-off-by: Filip Brozovic <fbrozovic@gmail.com>
Ye Li [Mon, 29 Jun 2020 02:12:26 +0000 (10:12 +0800)]
usb: gadget: Fix controller index in UMS
The usb mass storage (f_mass_storage.c) uses fixed usb index 0,
this causes problem while CDNS3 USB controller index is 1.
Modify the API of fsg to pass the controller index.
Reviewed-by: Jun Li <jun.li@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Hayes Wang [Tue, 16 Jun 2020 09:09:46 +0000 (17:09 +0800)]
eth/r8152: modify rtl_clear_bp function
The original rtl_clear_bp() is used to clear the firmware of both
PLA and USB MCU. The new one could clear the firmware of PLA or
USB independently. It is unnecessary to clear firmware, if there
is no one to be updated.
Besides, clear the firmware by writing the relative registers in
bulk.
Hayes Wang [Tue, 16 Jun 2020 09:09:44 +0000 (17:09 +0800)]
eth/r8152: reset bmu after disabling Tx/Rx
Reset bmu after disabling Tx/Rx. This is used to clear the FIFO of
Tx/Rx. The remained data may be transferred after Tx/Rx is re-enabled.
And it results in garbage data.
Marek Vasut [Sat, 9 May 2020 20:30:05 +0000 (22:30 +0200)]
serial: sh: Improve FIFO empty check on RX
If the SCIF is receiving data quickly enough, it may happen that the
SCxSR_RDxF flag is cleared in sh_serial_getc_generic(), while the
FIFO still contains data. If that happens, the serial_getc_check()
reports no data in the FIFO as the flag is no longer set. Add one
more check, if the SCxSR_RDxF is not set, read out the FIFO level
and if there are still characters in the FIFO, permit reading them
out.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
projects / u-boot.git / log
