- Enable SD slot on Intel Edison
- Populate CSRT ACPI table for shared DMA controller on Intel Tangier
- Convert Intel ICH-SPI driver to use new spi-mem ops
- Enable config_distro_bootcmd for QEMU x86
- Support U-Boot as a payload for Intel Slim Bootloader
- Avoid writing temporary asl files into the source tree which fixes the
parallel build issue occasionally seen
Dominik Sliwa [Thu, 1 Aug 2019 08:06:39 +0000 (11:06 +0300)]
apalis-tk1: remove non-essential power rails on boot
When mainline kernels reboot TK1 they use SW_RESET,
that reset mode does not reset PMIC. Some rails
need to be off for RAM Re-repair to work correctly.
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Signed-off-by: Dominik Sliwa <dominik.sliwa@toradex.com> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Marcel Ziswiler [Thu, 1 Aug 2019 08:06:38 +0000 (11:06 +0300)]
apalis-tk1: remove default vesa vga mode from vidargs
Remove video=tegrafb0:640x480-16@60 aka VESA VGA mode from vidargs in
order for the panel specification in the device tree to be used. This
causes the default to be the 10.1" LVDS display which will be available
in the Toradex webshop shortly.
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Marcel Ziswiler [Thu, 1 Aug 2019 08:06:31 +0000 (11:06 +0300)]
apalis-tk1: do not explicitly release reset_moci#
By keeping RESET_MOCI_CTRL low we avoid explicitly releasing
RESET_MOCI#.
Please note that module hardware versions up to V1.1A will already
release RESET_MOCI# in hardware coming out of reset.
Please further note that with this change the USB hub on the Apalis
Evaluation board is kept in reset in U-Boot and therefore none of its
ports are operational in U-Boot.
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Igor Opaniuk [Fri, 14 Jun 2019 07:59:10 +0000 (10:59 +0300)]
colibri/apalis tegra: drop DFU support
We never really added a sensible DFU configuration for platforms
based on eMMC. Most of the things one might want to do can also be done
with UMS or fastboot, so drop the DFU configuration.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Park, Aiden [Sat, 3 Aug 2019 08:31:20 +0000 (08:31 +0000)]
x86: Skip setting up MTRRs in slimbootloader
The setting up MTRRs have already been done in previous
Slim Bootloader stages.
Signed-off-by: Aiden Park <aiden.park@intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
Park, Aiden [Sat, 3 Aug 2019 08:31:11 +0000 (08:31 +0000)]
board: intel: Add new slimbootloader board
Add slimbootloader board to run U-boot as a Slim Bootloader payload
- Add new board/intel/slimbootloader directory with minimum codes
- Add slimbootloader configuration files
- Add doc/board/intel/slimbootloader.rst
Signed-off-by: Aiden Park <aiden.park@intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: add slimbootloader board MAINTAINERS file] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Park, Aiden [Sat, 3 Aug 2019 08:31:00 +0000 (08:31 +0000)]
x86: slimbootloader: Add a slimbootloader device tree
Add a new device tree which has very minimum nodes
- x86 reset
- x86 tsc_timer
- x86 pci
- Slim Bootloader serial
Signed-off-by: Aiden Park <aiden.park@intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
Park, Aiden [Sat, 3 Aug 2019 08:30:52 +0000 (08:30 +0000)]
x86: slimbootloader: Set TSC information for tsc_timer
Slim Bootloader already calibrated TSC and provides it to U-Boot.
Therefore, U-Boot does not have to re-calibrate TSC.
Configuring tsc_base and clock_rate makes x86 tsc_timer driver bypass
TSC calibration and use the provided TSC frequency.
- Get TSC frequency from performance info hob
- Set tsc_base and clock_rate for tsc_timer driver
Signed-off-by: Aiden Park <aiden.park@intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
Park, Aiden [Sat, 3 Aug 2019 08:30:44 +0000 (08:30 +0000)]
x86: slimbootloader: Add serial driver
Slim Bootloader provides serial port info thru its HOB list pointer.
All these HOBs are eligible for Slim Bootloader based board only.
- Get serial port information from the serial port info HOB
- Leverage ns16550 driver with slimbootloader specific platform data
Signed-off-by: Aiden Park <aiden.park@intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
Park, Aiden [Sat, 3 Aug 2019 08:30:36 +0000 (08:30 +0000)]
x86: slimbootloader: Add memory configuration
Slim Bootloader provides memory map info thru its HOB list pointer.
Configure memory size and relocation memory from the HOB data, and
provide e820 entries as well.
- Get memory size from the memory map info HOB
- Set available top memory lower than 4GB for U-Boot relocation
- Provide e820 entries from the memory map info HOB
Signed-off-by: Aiden Park <aiden.park@intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
Park, Aiden [Sat, 3 Aug 2019 08:30:31 +0000 (08:30 +0000)]
x86: Add a common HOB library
FSP (CONFIG_HAVE_FSP) and Slim Bootloader (CONFIG_SYS_SLIMBOOTLOADER)
consume HOB (CONFIG_USE_HOB) data from the each HOB list pointer.
Add a common HOB library in lib/hob.c and include/asm/hob.h.
Signed-off-by: Aiden Park <aiden.park@intel.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
Park, Aiden [Sat, 3 Aug 2019 08:30:20 +0000 (08:30 +0000)]
x86: lib: fsp: Use EFI_GUID and efi_guid_t
Use existing EFI_GUID and efi_guid_t instead of struct efi_guid.
This is pre-work before making a common HOB library.
- Change 'struct efi_guid' to efi_guit_t
- Remove 'struct efi_guid'
- Define GUIDs with EFI_GUID() macro
- Use guidcmp() instead of compare_guid()
- Remove compare_guid()
Signed-off-by: Aiden Park <aiden.park@intel.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested on MinnowMax Tested-by: Bin Meng <bmeng.cn@gmail.com>
Park, Aiden [Sat, 3 Aug 2019 08:30:12 +0000 (08:30 +0000)]
x86: Add new slimbootloader CPU type
This slimbootloader CPU type is to enable U-Boot as a payload which
runs on top of Slim Bootloader (https://github.com/slimbootloader).
The Slim Bootloader is designed with multi-stage architecture for
the execution from reset vector to OS booting, and supports QEMU,
Apollolake, Whiskeylake and Coffeelake platforms consuming Intel
FSP (https://github.com/IntelFsp) for silicon initialization
including CAR and memory initialization.
The Slim Bootloader generates new HOB (Hand Off Block) which are
serial port info, memory map info, performance data info and so on,
and passes it to a Payload. U-Boot as a payload will use these HOB
information for basic initialization such as serial console.
As an initial commit,
- Add CONFIG_SYS_SLIMBOOTLOADER to enable slimbootloader CPU type
- Add new arch/x86/cpu/slimbootloader directory with minimum codes
- Get hob_list pointer from Slim Bootloader
Signed-off-by: Aiden Park <aiden.park@intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
With the introduction of the new spi-mem model operations changed
slightly. The new spi-mem operations make things a bit easier to
handle for ich-spi flash interface. This patch converts the ich-spi
driver by using spi-mem operations.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested on Intel CrownBay and MinnowMax Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fix compiler warnings when building the driver for 64-bit] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 28 Jul 2019 20:16:28 +0000 (14:16 -0600)]
x86: Avoid writing temporary asl files into the source tree
At present the iasl tool (Intel ACPI (Advanced Configuration and Power
Interface) Source Language Compiler) is called in such a way that it uses
the source directory for its temporary files.
This means we end up with these files when building x86 boards:
Update the code to put temporary files in the target directory instead.
The iasl tool is quite confusing since it generates files with different
extensions and does not allow these to be individually specified. Add some
documentation to help with this.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: remove dsdt.hex from 'make clean' rules and correct U-Boot spelling] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Andy Shevchenko [Sun, 14 Jul 2019 16:23:58 +0000 (19:23 +0300)]
x86: acpi: Enable ACPI companion for Intel iDMA 32-bit
ACPI has a capability to specify DMA parameters for DMA channel consumers.
To enable this for Intel Edison, describe GP DMA device in ACPI table
in order to get an ACPI handle to it in OS.
This works in conjunction with CSRT, which must be in align with DSDT.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Andy Shevchenko [Sun, 14 Jul 2019 16:23:57 +0000 (19:23 +0300)]
x86: acpi: Introduce a stub to generate CSRT
Here is a stub function that generates an empty CSRT. If the target platform
provides acpi_fill_csrt() function, it will be used to populate the table.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Bin Meng [Sun, 28 Jul 2019 15:13:58 +0000 (08:13 -0700)]
x86: qemu: Fix non-working ramboot and nfsboot environment variables
With qemu-x86 starting to use config_distro_bootcmd, the pre-defined
ramboot and nfsboot commands do not work any more. This is caused by
undefined environment variable 'ramdiskaddr' that was previously set
in CONFIG_EXTRA_ENV_SETTINGS but later CONFIG_EXTRA_ENV_SETTINGS was
redefined for distro boot.
Update the x86 generic CONFIG_EXTRA_ENV_SETTINGS to consider distro
boot, and remove the one in qemu-x86.h.
Converts qemu x86 machines to boot using distro_config. The intent is to
allow u-boot in qemu to be maximally compatible with many boot methods
without having to change the config. Previously, u-boot would only boot
in a very limited set of circumstances where there was a /boot/vmlinuz
on scsi 0:3 with no ramdisk.
Signed-off-by: Joshua Watt <JPEWhacker@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: convert doc updates to reST] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tom Rini [Fri, 9 Aug 2019 11:29:20 +0000 (07:29 -0400)]
Merge tag 'u-boot-rockchip-20190809' of https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip
- Add rk3399 boards Khadas Edge/-V/-Captain
- Add fully souce code support for rk3328 including TPL/DRAM init
- Enable boot from eMMC for rk3399 rock960/ficus boards
- turn on the IO supply for dw_mmc
Peng Fan [Tue, 6 Aug 2019 02:48:04 +0000 (02:48 +0000)]
mmc: tangier_sdhci: fix uninitialized pointer deref on probe
Commit 3d296365e4e8 ("mmc: sdhci: Add support for
sdhci-caps-mask") sdhci_setup_cfg() expects a valid sdhci_host mmc
field.
Fixes: 3d296365e4e8 ("mmc: sdhci: Add support for sdhci-caps-mask") Cc: Faiz Abbas <faiz_abbas@ti.com> Cc: Vincent Tinelli <vincent.tinelli@intel.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Tue, 6 Aug 2019 02:47:59 +0000 (02:47 +0000)]
mmc: s5p: fix uninitialized pointer deref on probe
Commit 3d296365e4e8 ("mmc: sdhci: Add support for
sdhci-caps-mask") sdhci_setup_cfg() expects a valid sdhci_host mmc
field.
Fixes: 3d296365e4e8 ("mmc: sdhci: Add support for sdhci-caps-mask") Cc: Faiz Abbas <faiz_abbas@ti.com> Cc: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Tue, 6 Aug 2019 02:47:56 +0000 (02:47 +0000)]
mmc: pci: fix uninitialized pointer deref on probe
Commit 3d296365e4e8 ("mmc: sdhci: Add support for
sdhci-caps-mask") sdhci_setup_cfg() expects a valid sdhci_host mmc
field.
Fixes: 3d296365e4e8 ("mmc: sdhci: Add support for sdhci-caps-mask") Cc: Faiz Abbas <faiz_abbas@ti.com> Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Tue, 6 Aug 2019 02:47:53 +0000 (02:47 +0000)]
mmc: msm_sdhci: fix uninitialized pointer deref on probe
Commit 3d296365e4e8 ("mmc: sdhci: Add support for
sdhci-caps-mask") sdhci_setup_cfg() expects a valid sdhci_host mmc
field.
Fixes: 3d296365e4e8 ("mmc: sdhci: Add support for sdhci-caps-mask") Cc: Faiz Abbas <faiz_abbas@ti.com> Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Tue, 6 Aug 2019 02:47:50 +0000 (02:47 +0000)]
mmc: bcm: fix uninitialized pointer deref on probe
Commit 3d296365e4e8 ("mmc: sdhci: Add support for
sdhci-caps-mask") sdhci_setup_cfg() expects a valid sdhci_host mmc
field.
Fixes: 3d296365e4e8 ("mmc: sdhci: Add support for sdhci-caps-mask") Cc: Faiz Abbas <faiz_abbas@ti.com> Cc: Matthias Brugger <mbrugger@suse.com> Cc: Thomas Fitzsimmons <fitzsim@fitzsim.org> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Tue, 6 Aug 2019 02:47:47 +0000 (02:47 +0000)]
mmc: atmel_sdhci: fix uninitialized pointer deref on probe
Commit 3d296365e4e8 ("mmc: sdhci: Add support for
sdhci-caps-mask") sdhci_setup_cfg() expects a valid sdhci_host mmc
field.
Fixes: 3d296365e4e8 ("mmc: sdhci: Add support for sdhci-caps-mask") Cc: Faiz Abbas <faiz_abbas@ti.com> Cc: Wenyou Yang <wenyou.yang@atmel.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Tested-by: Eugen Hristev <eugen.hristev@microchip.com>
mmc: zynq_sdhci: fix uninitialized pointer deref on probe
Since commit 3d296365e4e8 ("mmc: sdhci: Add support for
sdhci-caps-mask") sdhci_setup_cfg() expects a valid sdhci_host mmc
field. Move the mmc field initialization before sdhci_setup_cfg()
call to avoid crash on mmc pointer dereference.
[this patch is based on commit 41a9fab8dac8 ("mmc: mv_sdhci: fix
uninitialized pointer deref on probe") by Baruch Siach]
Fixes: 3d296365e4e8 ("mmc: sdhci: Add support for sdhci-caps-mask") Cc: Faiz Abbas <faiz_abbas@ti.com> Cc: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu102/zc706)
Sam Protsenko [Wed, 3 Jul 2019 16:34:07 +0000 (19:34 +0300)]
fastboot: Remove "bootloader-version" variable
As per [1], there is no such fastboot variable as "bootloader-version".
Only "version-bootloader" is supported. Let's reflect this and not
confuse users further.
Sam Protsenko [Wed, 3 Jul 2019 16:00:22 +0000 (19:00 +0300)]
fastboot: getvar: Add "is-userspace" variable
As per documentation [1], Android-Q requires for bootloader to provide
"is-userspace" variable. "no" value should be always returned. This
patch implements this fastboot variable.
Marek Szyprowski [Fri, 21 Jun 2019 13:39:29 +0000 (15:39 +0200)]
thor: fix crash after usb initialization failure
Registration of USB download gadget might fail for various reasons, so
add a check for g_dnl_register() funtion return value. Without this fix,
thor_init() will try to access the registered gadget structures resulting
in NULL pointer dereference issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
commit 57faca19a82f ("drivers: USB: OHCI: allow compilation for 64-bit targets")
broke ohci support for the mpc85xx based socrates board,
as it removed volatile keyword from ohci_readl/writel.
Alex Deymo [Mon, 5 Aug 2019 20:24:45 +0000 (22:24 +0200)]
Update include/android_image.h from AOSP
This takes the latest changes from AOSP from the file
include/bootimg/bootimg.h from the repository:
https://android.googlesource.com/platform/system/tools/mkbootimg
and update the U-Boot version with the latest changes.
This file keeps the changes from AOSP to a minimum:
* Comments were converted from C++ to C style.
* Code inside __cplusplus #ifdef blocks were removed.
* C++11 struct extensions replaced with a single struct.
Signed-off-by: Alex Deymo <deymo@google.com> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Julius Werner [Fri, 2 Aug 2019 22:52:28 +0000 (15:52 -0700)]
fit: Do not automatically decompress ramdisk images
The Linux ramdisk should always be decompressed by the kernel itself,
not by U-Boot. Therefore, the 'compression' node in the FIT image should
always be set to "none" for ramdisk images, since the only point of
using that node is if you want U-Boot to do the decompression itself.
Yet some systems populate the node to the compression algorithm used by
the kernel instead. This used to be ignored, but now that we support
decompression of all image types it becomes a problem. Since ramdisks
should never be decompressed by U-Boot anyway, this patch adds a special
exception for them to avoid these issues. Still, setting the
'compression' node like that is wrong in the first place, so we still
want to print out a warning so that third-party distributions doing this
can notice and fix it.
Signed-off-by: Julius Werner <jwerner@chromium.org> Reviewed-by: Heiko Schocher <hs@denx.de> Tested-by: Heiko Schocher <hs@denx.de> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
console: execute flush on uart when silent is removed
Avoid to flush buffer when silent console is activated as the
console can be reactivate later, after relocation, when the env will
be updated with the saved one.
Solve issue (missing beginning of U-Boot trace) when:
- CONFIG_SILENT_CONSOLE is activated
- silent=1 is defined in default environment (CONFIG_EXTRA_ENV_SETTINGS)
- silent is removed in saved environment with:
> env delete silent; env save
Only functional when PRE_CONSOLE_BUFFER is activated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Update the "silent" property with the variable "silent" get from
saved environment, it solves the issue when:
- CONFIG_SILENT_CONSOLE and CONFIG_SYS_CONSOLE_IS_IN_ENV are activated
- silent is not defined in default environment
- silent is requested in saved environment with:
> env set silent 1; env save
On next reboot the console is not disabled as expected after relocation
and the environment load from flash (the callback is not called when
the INSERT is requested in the created hash table)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Sam Protsenko [Wed, 31 Jul 2019 16:59:09 +0000 (19:59 +0300)]
cmd: avb: Fix compiler warnings
When building U-Boot with AVB enabled, compiler shows next warnings:
cmd/avb.c: In function 'do_avb_read_pvalue':
cmd/avb.c:371:18: warning: format '%ld' expects argument of type
'long int', but argument 2 has type 'size_t'
{aka 'unsigned int'} [-Wformat=]
printf("Read %ld bytes, value = %s\n", bytes_read,
~~^ ~~~~~~~~~~
%d
cmd/avb.c: In function 'do_avb_write_pvalue':
cmd/avb.c:404:19: warning: format '%ld' expects argument of type
'long int', but argument 2 has type '__kernel_size_t'
{aka 'unsigned int'} [-Wformat=]
printf("Wrote %ld bytes\n", strlen(value) + 1);
~~^ ~~~~~~~~~~~~~~~~~
%d
Fix those by using "%zu" specified.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
common/avb_verify.c: In function 'read_persistent_value':
common/avb_verify.c:867:6: warning: implicit declaration of function
'get_open_session'
common/avb_verify.c:870:45: error: 'struct AvbOpsData' has no member
named 'tee'
common/avb_verify.c:894:7: warning: implicit declaration of function
'invoke_func'
common/avb_verify.c: In function 'write_persistent_value':
common/avb_verify.c:931:45: error: 'struct AvbOpsData' has no member
named 'tee'
Guard read_persistent_value() and write_persistent_value() functions
by checking if CONFIG_OPTEE_TA_AVB is enabled (as those are only used in
that case) to fix the build with mentioned configuration.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Ramon Fried [Wed, 31 Jul 2019 08:04:26 +0000 (11:04 +0300)]
pci_ep: Fix Coverity warning
Fix the following Coverity warning:
CID 244086: Incorrect expression (BAD_COMPARE)
Comparing pointer "ep_bar" against NULL using anything besides == or
is likely to be incorrect.
autoboot: fix bug using with CAAM and AUTOBOOT_ENCRYPTION
if CONFIG_AUTOBOOT_KEYED, CONFIG_AUTOBOOT_ENCRYPTION and
CONFIG_AUTOBOOT_STOP_STR_SHA256 are enabled in conjunction
with CONFIG_SHA_HW_ACCEL and CONFIG_FSL_CAAM, we get the
Error when pressing a key while waiting for bootdelay:
Error: Address arguments are not aligned
CAAM was not setup properly or it is faulty
Reason is, that used variables are not cache aligned,
so malloc this variables cache aligned.
Probably this is also a bugfix for other hw accelerators
than CAAM.
Kever Yang [Fri, 2 Aug 2019 07:40:02 +0000 (10:40 +0300)]
rockchip: evb-rk3328: enable defconfig options for TPL/SPL
Enable driver options for TPL/SPL in evb-rk3328_defconfig.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
[cherry picked from commit https://github.com/rockchip-linux/u-boot/commit/df4f40acb449815384e397dcaf5b618bbc6cd855 with minor modifications] Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Fri, 2 Aug 2019 07:40:01 +0000 (10:40 +0300)]
rockchip: Kconfig: enable TPL support for rk3328
Enable TPL support and some related option in Kconfig.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
[cherry picked from commit https://github.com/rockchip-linux/u-boot/commit/430b01462bf3f24aaf7920ae2587a6943c39ab5d with minor modifications] Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Fri, 2 Aug 2019 07:40:00 +0000 (10:40 +0300)]
rockchip: dts: rk3328: update dmc node for driver
Update dmc node for full feature driver.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
[cherry picked from commit https://github.com/rockchip-linux/u-boot/commit/1e1495636574c78ea9d3af3e0aae95d5204612d6 with minor modifications] Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Fri, 2 Aug 2019 07:39:59 +0000 (10:39 +0300)]
rockchip: ram: add full feature rk3328 DRAM driver
This driver supports DDR3/LPDDR3/DDR4 SDRAM initialization.
Signed-off-by: YouMin Chen <cym@rock-chips.com> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
[cherry picked from commit https://github.com/rockchip-linux/u-boot/commit/9fb0777ec3cc6a89af9d2e0969c3bfe58306a88d with minor modifications] Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
arm: dts: ficus: Enable booting from eMMC when using SPL
This commits enables booting from eMMC when using SPL on 96Boards
Ficus board by adding SDHCI to boot order. Since the SDHCI driver
already has the reloc flag, this works straightaway. While we are at it,
let's also include the common u-boot dtsi for rk3399.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
arm: dts: rock960: Enable booting from eMMC when using SPL
This commits enables booting from eMMC when using SPL on 96Boards
Rock960 board by adding SDHCI to boot order. Since the SDHCI driver
already has the reloc flag, this works straightaway. While we are at it,
let's also include the common u-boot dtsi for rk3399.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Nick Xie [Tue, 30 Jul 2019 03:51:16 +0000 (11:51 +0800)]
arm64: dts: rockchip: Add support for Khadas Edge-Captain
Add devicetree support for Khadas Edge-Captain.
Khadas Captain is the carrier board for Khadas Edge.
Specification
- Rockchip RK3399
- Dual-Channel 2GB/4GB LPDDR4
- SD card slot
- Onboard 16GB/32GB/128GB eMMC
- RTL8211FD 1Gbps
- AP6356S/AP6398S WiFI/BT
- HDMI Out, DP, MIPI DSI/CSI, eDP
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- Full 4 Lane M.2 Socket
- 16MB SPI Flash
- IR
- Programmable MCU
Commit details of rk3399-khadas-edge-*.dts sync from Linux 5.3-rc2:
"arm64: dts: rockchip: Add support for Khadas Edge/Edge-V/Captain boards"
(sha1: c2aacceedc86af87428d998e23a1aca24fd8aa2e)
Signed-off-by: Nick Xie <nick@khadas.com> Tested-by: Chris Webb <chris@arachsys.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Nick Xie [Tue, 30 Jul 2019 03:51:15 +0000 (11:51 +0800)]
arm64: dts: rockchip: Add support for Khadas Edge-V
Add devicetree support for Khadas Edge-V.
Khadas Edge-V is a Khadas VIM form factor Rockchip RK3399 board.
Specification
- Rockchip RK3399
- Dual-Channel 2GB/4GB LPDDR4
- SD card slot
- Onboard 16GB/32GB/128GB eMMC
- RTL8211FD 1Gbps
- AP6356S/AP6398S WiFI/BT
- HDMI Out, DP, MIPI DSI/CSI, eDP
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- Full 4 Lane M.2 Socket
- 16MB SPI Flash
- IR
- Programmable MCU
Commit details of rk3399-khadas-edge-*.dts sync from Linux 5.3-rc2:
"arm64: dts: rockchip: Add support for Khadas Edge/Edge-V/Captain boards"
(sha1: c2aacceedc86af87428d998e23a1aca24fd8aa2e)
Signed-off-by: Nick Xie <nick@khadas.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
projects / u-boot.git / log
