The Rockchip-released ATF for the Firefly apparently (i.e. Kever
reported this) does not tolerate a FDT being passed as the platform
parameter and will run into a hard stop.
To work around this limitation in the ATF parameter handling, we
enable SPL_ATF_NO_PLATFORM_PARAM (which will force passing NULL for
the platform parameters).
Note that this only affects this platform, as the ATF releases for the
RK3368 and RK3399 have always either ignored the platform parameter
(i.e. before the FDT-based parameters were supported) or support
receiving a pointer to a FDT.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Philipp Tomsich [Tue, 2 Jan 2018 20:16:43 +0000 (21:16 +0100)]
spl: atf: add SPL_ATF_NO_PLATFORM_PARAM option
While we expect to call a pointer to a valid FDT (or NULL) as the
platform parameter to an ATF, some ATF versions are not U-Boot aware
and have an insufficiently robust (or an overzealour) parameter
validation: either way, this may cause a hard-stop with uncooperative
ATF versions.
This change adds the option to suppress passing a platform parameter
and will always pass NULL.
Debug output from ATF w/ this option disabled (i.e. default):
INFO: plat_param_from_bl2: 0x291450
Debug output from ATF w/ this option enabled:
INFO: plat_param_from_bl2: 0
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Peng Fan [Tue, 2 Jan 2018 07:25:37 +0000 (15:25 +0800)]
video: Support multiple lines version string display
The calculation of left space for version string is not correct, should
use VIDEO_COLS not VIDEO_LINE_LEN / 2, otherwise we will get larger space
than actual have and cause string to overlay logo picture.
Also current version string display only supports two lines words at max.
This also causes overlay when the LCD pixel column size is not enough.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Tested-by: Anatolij Gustschin <agust@denx.de>
Philipp Tomsich [Tue, 2 Jan 2018 17:43:37 +0000 (18:43 +0100)]
rockchip: board: lion-rk3368: reduce env-size default to 8KiB
We want to have the same configuration defaults for the RK3368-uQ7
as for the RK3399-Q7: this change reduces the default env-size to
8KiB to ensure that it does not overlap the boot-payload on SD/MMC
configurations.
References: commit fe529e6597c0 ("rockchip: rk3399-puma: reduce env size to 8kiB") Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Felix Brack [Mon, 18 Dec 2017 14:38:28 +0000 (15:38 +0100)]
power: tps65910: replace error() by pr_err()
The patch replaces the former error() by the new pr_err().
This makes the TPS65910 driver conform to Masahiro's patch
'treewide:replace with error() with pr_err()' introduced
October 2017.
Signed-off-by: Felix Brack <fb@ltec.ch> Reviewed-by: Simon Glass <sjg@chromium.org>
Sam Protsenko [Thu, 28 Dec 2017 21:03:25 +0000 (23:03 +0200)]
configs: am335x_boneblack: Bring back missed bootcmd
Commit b6251db8c3f0 ("Kconfig: Introduce USE_BOOTCOMMAND and migrate
BOOTCOMMAND") removed CONFIG_BOOTCOMMAND option from
include/configs/am335x_evm.h file. But that option wasn't added to
defconfig files for BeagleBone Black board.
Because of this we can't boot Linux from SD card using just
"run bootcmd", getting next error:
** File not found /boot/undefined **
That's because "fdtfile" variable has "undefined" value by default, and
"bootcmd" doesn't call "run findfdt" command, which assigns "fdtfile" to
correct device tree file for current board name (obtained from EEPROM).
So we are forced to either call "run findfdt" command manually, or
assign manually "fdtfile=am335x-boneblack.dtb" (e.g. in uEnv.txt file).
Bring back CONFIG_BOOTCOMMAND to BBB defconfigs so that we can boot
Linux rootfs from SD card automatically without any addition actions.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Kever Yang [Wed, 20 Dec 2017 02:40:40 +0000 (10:40 +0800)]
rockchip: dts: rk3399-evb: support boot from sd-card
Enable sdmmc node in SPL and add it to boot order.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Fixed commit tags:] Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This commit changes the size of the enviroment (for the RK3399-Q7) to
8kiB for all possible locations of the environment (i.e. even when the
environment is saved to SD card).
With the default of 32kiB, the environment overwrites the SPL
stage which lives at 16kiB.
Signed-off-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Reworked commit-message:] Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
imx: Fix missing spl_sd configuration for wandboard.
In commit 6e6cf015e7cdd7ca83a933320a81201972bd5e5e ("Merge
git://www.denx.de/git/u-boot-imx") the line defining spl_sd
configuration for wandboard was removed, which resulted in no SPL
target being built.
Breno Lima [Mon, 27 Nov 2017 23:09:00 +0000 (21:09 -0200)]
imx: Kconfig: Add HAS_CAAM option
Currently CONFIG_SECURE_BOOT is selecting FSL_CAAM for all i.MX devices,
this causes the following error when building mx6sl boards since
this SoC doesn't have the CAAM block:
In file included from drivers/crypto/fsl/jobdesc.c:12:0:
drivers/crypto/fsl/jobdesc.c: In function 'inline_cnstr_jobdesc_blob_dek':
include/fsl_sec.h:268:25: error: 'CAAM_ARB_BASE_ADDR' undeclared (first use
in this function)
#define SEC_MEM_PAGE1 (CAAM_ARB_BASE_ADDR + 0x1000)
^
drivers/crypto/fsl/jobdesc.c:140:21: note: in expansion of macro 'SEC_MEM_PAGE1'
memcpy((uint32_t *)SEC_MEM_PAGE1, (uint32_t *)plain_txt, in_sz);
^
include/fsl_sec.h:268:25: note: each undeclared identifier is reported only
once for each function it appears in
#define SEC_MEM_PAGE1 (CAAM_ARB_BASE_ADDR + 0x1000)
^
drivers/crypto/fsl/jobdesc.c:140:21: note: in expansion of macro 'SEC_MEM_PAGE1'
memcpy((uint32_t *)SEC_MEM_PAGE1, (uint32_t *)plain_txt, in_sz);
^
scripts/Makefile.build:280: recipe for target 'drivers/crypto/fsl/jobdesc.o'
failed
make[3]: *** [drivers/crypto/fsl/jobdesc.o] Error 1
scripts/Makefile.build:425: recipe for target 'drivers/crypto/fsl' failed
make[2]: *** [drivers/crypto/fsl] Error 2
scripts/Makefile.build:425: recipe for target 'drivers/crypto' failed
make[1]: *** [drivers/crypto] Error 2
Add HAS_CAAM configuration to avoid this error.
Signed-off-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
ARM: imx: cm_fx6: remove esdhc init code from board file
Commit 5248930ebf48 ("dm: imx: cm_fx6: Enable more driver model support")
enabled driver model support for MMC. Remove the old mmc init code, which
is no longer used, from the board file.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org>
ARM: imx: cm_fx6: remove sata init code from board file
Commit 5248930ebf48 ("dm: imx: cm_fx6: Enable more driver model support")
enabled driver model support for AHCI. Remove the old, now unused, sata
init code from the board file.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Commit 5248930ebf48 ("dm: imx: cm_fx6: Enable more driver model support")
enabled driver model support for USB. But it missed to enable driver
model support for keyboards. As a result, USB keyboards do no longer
work.
Fix this by enabling driver model support for keyboards.
Fixes: 5248930ebf48 ("dm: imx: cm_fx6: Enable more driver model support") Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org>
ARM: imx: cm-fx6: reinstate USB support by syncing the devicetree with Linux
Commit 5248930ebf48 ("dm: imx: cm_fx6: Enable more driver model support")
enabled driver model support for USB, thereby effectively removing USB
support because the cm_fx6 devicetree in the U-Boot does *not* enable the
USB nodes.
Reinstate the USB support by syncing the devicetree with Linux whose
devicetree enables the USB nodes properly.
More precisely, use the devicetree found in Linux v4.15-rc1 with the
following two changes:
1) Remove the audio mux; the required dt-bindings header is not
present in the U-Boot.
2) Keep the usdhc3 MMC controller node currently present in the
U-Boot's devicetree to retain the ability to boot from MMC.
Fixes: 5248930ebf48 ("dm: imx: cm_fx6: Enable more driver model support") Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Fabio Estevam [Mon, 20 Nov 2017 13:54:33 +0000 (11:54 -0200)]
imx: Unify CONFIG_BOOTDELAY
In order to provide a consistent user experience for imx board users,
remove the custom CONFIG_BOOTDELAY values from defconfig files, so that
all boards can use the default two second delay.
common: Fix-up MAC addr in dts by fetching env variable serially
The MAC addresses get fixed in the device tree for "ethernet" nodes
is by using trailing number behind "ethernet" found in "/aliases".
It may not be necessary for the "ethernet" nodes to be sequential.
There can be gaps in between or any node disabled
So provide a support to fetch MAC addr sequentially from env
and apply them to "ethernet" nodes in the order they appear in
device tree only if "ethernet" is not "disabled"
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Sean Nyekjaer [Fri, 15 Dec 2017 07:51:54 +0000 (08:51 +0100)]
mtd/spi: fix block count for is25lq040b
This spi-nor is 4Mbit/512KB
Fixes: b4fbcbc5a5 ("mtd/spi: add support for is25lq040b") Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk> Reviewed-by: Jagan Teki <jagan@openedev.com>
Jerome Brunet [Tue, 12 Dec 2017 15:03:55 +0000 (16:03 +0100)]
net: phy: meson-gxl: detect LPA corruption
This patch is ported from the Linux patch posted at [1] and applied to
net tree as commit f1e2400a80ff.
The purpose of this change is to fix the incorrect detection of the link
partner (LP) advertised capabilities which sometimes happens with this PHY
(roughly 1 time in a dozen)
This issue may cause the link to be negotiated at 10Mbps/Full or
10Mbps/Half when 100MBps/Full is actually possible. In some case, the link
is even completely broken and no communication is possible.
To detect the corruption, we must look for a magic undocumented bit in the
WOL bank (hint given by the SoC vendor kernel) but this is not enough to
cover all cases. We also have to look at the LPA ack. If the LP supports
Aneg but did not ack our base code when aneg is completed, we assume
something went wrong.
The detection of a corrupted LPA triggers a restart of the aneg process.
This solves the problem but may take up to 6 retries to complete.
Tom Rini [Mon, 18 Dec 2017 17:23:27 +0000 (12:23 -0500)]
Merge tag 'xilinx-for-v2018.01-rc2-v2' of git://www.denx.de/git/u-boot-microblaze
Xilinx changes for v2018.01-rc2-v2
fpga:
- Enable loading bitstream via fit image for !xilinx platforms
zynq:
- Fix SPL SD boot mode
zynqmp:
- Not not reset in panic
- Do not use simple allocator because of fat changes
- Various dt chagnes
- modeboot variable setup
- Fix fpga loading on automotive devices
- Fix coverity issues
test:
- Fix env test for !hush case - Stephen's patch
York Sun [Mon, 11 Dec 2017 16:39:05 +0000 (08:39 -0800)]
armv8: ls1046aqds: Adjust IFC timing for NOR flash
Increase setup, assertion and hold time related to chip-select signal.
Additional delay is needed for the signal to propogate through FPGA.
This adjustment slightly increase the read and write cycle but has no
impact on burst read or write.
Kever Yang [Fri, 15 Dec 2017 03:15:03 +0000 (11:15 +0800)]
rockchip: add a common script for generate fit its
Rockchip release bl31.elf file for armv8 SoCs like rk3399, rk3328,
the elf have more than one section, we need to decode it first and
packed them into u-boot.itb with its file. This script is to generate
the its script.
Need default bl31.elf in root directory of U-Boot source and dtb
as parameter.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Fri, 15 Dec 2017 03:15:04 +0000 (11:15 +0800)]
rockchip: firefly-rk3399: add FIT for rk3399
Enable SPL_FIT_GENERATOR with path for it.
With this patch you can get u-boot.itb for rk3399-firefly with:
> make u-boot.itb
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Mark Kettenis <kettenis@openbsd.org> Tested-by: Mark Kettenis <kettenis@openbsd.org> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Fri, 15 Dec 2017 03:15:05 +0000 (11:15 +0800)]
rockchip: evb-rk3399: update document for board bring up
Since we support ATF in SPL and add script for it, let's make the
document up to date.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Mon, 18 Dec 2017 07:13:19 +0000 (15:13 +0800)]
rockchip: update ROCKCHIP_SPL_RESERVE_IRAM to 0
Only rk3399 atf need ROCKCHIP_SPL_RESERVE_IRAM. This commit updates
its default setting to 0 so that other SoCs do not need to define it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Mon, 18 Dec 2017 07:05:41 +0000 (15:05 +0800)]
rockchip: update boot0 hook
Rockchip SoCs only need boot0 hook at SPL, and the U-Boot proper do not
need it.
The very beginning of U-Boot proper is different between armv7 and armv8:
armv7 start with ARM_VECTORS while armv8 start with 'b reset'.
Here is the map of very beginning for all cases:
armv7 SPL: TAG(overwrite 'b 1f')+'b reset' + ARM_VECTORS
armv7 U-Boot: ARM_VECTORS
armv8 SPL: TAG(overwrite 'b 1f')+'b reset' + Reserved_iram(rk3399)
armv8 U-Boot: 'b reset'
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
arm64: zynqmp: Access timestamp_ref_ctrl register only if running in el3
Access the timestamp ref ctrl register only if runinng
at el3 level otherwise just return. This change fixes
the issue when CRL APB is marked as secure and accessing
when not in el3 causes exception.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
arm64: zynqmp: Dont use 4K sector erase by default for spi-flashes
Dont use 4K sector erase by default, Disabling this
would use 64K sector erase and decreases erase time.
Also disabled by the fact that UBIFS and JFFS2 won't work
with 4K sector erase.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Klaus Goger [Mon, 11 Dec 2017 16:56:08 +0000 (17:56 +0100)]
rockchip: move CONFIG_ENV_SIZE and CONFIG_ENV_OFFSET to Kconfig
This commit adds ENV_SIZE and ENV_OFFSET configuration items for
ARCH_ROCKCHIP, but keeps these non-visible (i.e. not prompt is given).
With these new items present, the configuration from the header files
is moved to Kconfig.
Keeping these non-visible is necessary to have the possibility to
select new default values if CONFIG_IS_IN_* is changed (interactively
or with oldconfig). Otherwise it will always be set to a previous
value if used with a prompt. As an example if we do a defconfig with
CONFIG_IS_IN_MMC and change it to CONFIG_IS_IN_SPI_FLASH via
menuconfig, ENV_SIZE and ENV_OFFSET will not be changed to the correct
values as defconfig will already have set them to the default values
of CONFIG_IS_IN_MMC in .config.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tom Rini [Sun, 17 Dec 2017 20:37:29 +0000 (15:37 -0500)]
Merge tag 'signed-efi-v2018.01' of git://github.com/agraf/u-boot
Patch queue for efi - 2017-12-17
A few fixes for 2018.01:
- Compile fix with helloworld example
- DP match fix (fixes FreeBSD loader and grub on block storage)
- More DP fixes for SD, block
- Fix use-after-free
rockchip: rk3399-puma: set gpio4cd iodomain to 1.8V
The PCIe reset signal is connected to GPIO4_C6 on the Puma
module. This pin is supplied by 1.8V, but the default iodomain
setting is 3.0V and in this situation the pin is unable to go
high.
Linux assumes that this signal works in early boot
as PCIe is probed before loading the iodomain driver.
Make PCIe work in Linux by setting the gpio4cd iodomain to 1.8V.
Signed-off-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Tue, 31 Oct 2017 08:52:23 +0000 (16:52 +0800)]
rockchip: config: update part table
User do not need to access the reserved part in system, remove them
from partition table.
Rename atf to trust as generic name for armv7 do not use ATF.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
If a failure occurs when trying to load an image, it is insufficient
to free() the EFI object. We must remove it from the object list,
too. Otherwise a use after free will occur the next time we
iterate over the object list.
Furthermore errors in setting up the image should be handled.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
When calling efi_dp_find_obj(), we usually want to find the *exact* match
of an object for a given device path. However, I ran into a nasty corner case
where I had the following objects with paths available:
because that path is a full substring of the path we were searching for.
So this patch adapts the device path search logic to always look for exact
matches first. The way we distinguish between those cases is by looking at
whether our caller actually deals with remainders.
As a side effect, the code as is from all I can tell now never does a
substring match anymore, because it always gets called with rem=NULL, so
we always only do exact matches now.
Reported-by: Jonathan Gray <jsg@jsg.id.au> Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Mon, 11 Dec 2017 08:40:47 +0000 (09:40 +0100)]
efi_loader: helloworld.c: Explicitly use .rodata for loaded_image_guid
Commit bbf75dd9345d0b ("efi_loader: output load options in helloworld")
introduced a const variable in efi_main() called loaded_image_guid which
got populated from a constant struct.
While you would usually expect a compiler to realize that this variable
should really just be a global pointer to .rodata, gcc disagrees and instead
puts it on the stack. Unfortunately in some implementations of gcc it does
so my calling memcpy() which we do not implement in our hello world
environment.
So let's explicitly move it to a global variable which in turn puts it in
.rodata reliably and gets rid of the memcpy().
Fixes: bbf75dd9345d0b ("efi_loader: output load options in helloworld") Reported-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Alexander Graf <agraf@suse.de> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Yangbo Lu [Fri, 8 Dec 2017 07:35:37 +0000 (15:35 +0800)]
armv8: ls1012ardb: support hwconfig for eSDHC1 enabling
I2C reading for DIP switch setting is not reliable for LS1012ARDB
RevD and later versions. This patch is to add hwconfig support to
enable/disable eSDHC1 manually for these boards. Also drop 'status'
fix-up for eSDHC0 and leave it as it is. It shouldn't always be
fixed up with 'okay'.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Yogesh Gaur [Thu, 7 Dec 2017 05:40:14 +0000 (11:10 +0530)]
board/ls2080a, ls1088a: Add check for mc-dpl applied in fdt
Function fdt_fixup_board_enet() performs fdt fixup. Only return
fdt_status_okay() when both MC is applied and DPL is deployed, else
return fdt_status_fail().
This check is added to LS1088A/LS2080A/LS2088A boards.
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Michal Simek [Wed, 6 Dec 2017 07:33:50 +0000 (08:33 +0100)]
arm64: zynqmp: Add support for zynqmp automotive silicons
Remove silicon prefix. Automotive grade devices are using xazu instead
of xczu prefix.
The patch "fpga: xilinx: Check for substring in device ID validation"
(sha1: f72132673a01216e760864e442f168977cce2bd2)
enables this functionality for zynq devices that only substrings are
checked.
Unfortunately there is no way how to detect device grade that's why
this change is reasonable.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 27 Feb 2017 07:11:38 +0000 (08:11 +0100)]
arm64: zynqmp: Use only earlycon bootargs instead of full one
This is the same patch as was done earlier.
Please look at Linux patch:
"arm64: zynqmp: Use only earlycon bootargs instead of full one"
(sha1: f3609c8d4af28b9cc22ca49bf8e529b582ec188c)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
projects / u-boot.git / log
