Hou Zhiqiang [Fri, 5 Feb 2021 08:34:02 +0000 (16:34 +0800)]
configs: T1042: Drop the CONFIG_VIDEO
Drop the CONFIG_VIDEO to fix the following build warning.
===================== WARNING ======================
This board does not use CONFIG_DM_VIDEO Please update
the board to use CONFIG_DM_VIDEO before the v2019.07 release.
UPD include/generated/dt.h
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
UPD include/generated/timestamp_autogenerated.h
====================================================
Hou Zhiqiang [Fri, 5 Feb 2021 07:45:12 +0000 (15:45 +0800)]
armv7: ls102xa: Enable I-Cache to speed up the boot time
Enable the I-Cache to speed up the boot time, especailly for the NOR
boot, currently it takes about 15 seconds from power up to the U-Boot
prompt, and with the I-Cache enabled it only takes around 2.5 seconds.
LX2162A is not like LX2160A which has different PCIe controller
in rev1 and rev2 silicon. It supports only one configuration of
PCIe controller, which is same as LS2088A. So update PCIe
compatible string same as LS2088A.
Mathew McBride [Mon, 25 Jan 2021 03:55:22 +0000 (03:55 +0000)]
spi: fsl_qspi: apply the same settings for LS1088 as LS208x
The LS1088 requires the same QUADSPI_QURIK_BASE_INTERNAL
workaround as the LS208x and also has a 64 byte TX buffer.
With the previous settings SPI-NAND reads over AHB were
corrupted.
Fixes: 91afd36f3802 ("spi: Transform the FSL QuadSPI driver to use the SPI MEM API") Signed-off-by: Mathew McBride <matt@traverse.com.au> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Mathew McBride [Mon, 25 Jan 2021 03:55:21 +0000 (03:55 +0000)]
spi: fsl_qspi: Ensure width is respected in spi-mem operations
Adapted from kernel commit b0177aca7aea
From: Michael Walle <michael@walle.cc>
Make use of a core helper to ensure the desired width is respected
when calling spi-mem operators.
Otherwise only the SPI controller will be matched with the flash chip,
which might lead to wrong widths. Also consider the width specified by
the user in the device tree.
Fixes: 91afd36f38 ("spi: Add a driver for the Freescale/NXP QuadSPI controller") Signed-off-by: Michael Walle <michael@walle.cc> Link: https://lore.kernel.org/r/20200114154613.8195-1-michael@walle.cc Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Mathew McBride <matt@traverse.com.au> [adapt for U-Boot] Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Niel Fourie [Thu, 21 Jan 2021 12:19:18 +0000 (13:19 +0100)]
PowerPC: dts: Pulled in kmcent2 dts files from Linux 5.10
Pulled in the kmcent2.dts and all its dependents from Linux 5.10,
commit 2c85ebc57b3e upstream. Replaced the license text with
SPDX License Identifiers.
Take into account SDRAM_BASE address when calculating pnvramaddr and
varaddr offsets.
Up to now Keymile designs had SDRAM_BASE equal to zero and the offsets
where calculated correctly, this fix is for the upcoming designs that
have SDRAM_BASE different then zero.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
keymile: common: qrio: print QRIO id and revision number
Add show_qrio function to print chip id and revision information.
There are already multiple QRIO chip versions available and the upcoming
designs may want to show used version.
board: keymile: common: fix qrio compilation for arm
This patch is fixing qrio driver compilation for ARM architecture:
- It includes asm/io.h for in_/out_ access
- It use correct names for set/clear_bits as defined in linux/bitops.h
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Michael Walle [Thu, 7 Jan 2021 23:08:59 +0000 (00:08 +0100)]
board: sl28: add SATA support
Enable SATA support. Although not supported by the usual SATA pins on
the SMARC baseboard connector, SATA mode is supported on a PCIe lane.
This way one can use a mSATA card in a Mini PCI slot.
We need to invert the received data because in this mode the polarity of
the SerDes lane is swapped. Provide a fixup in board_early_init_f() for
the SPL. board_early_init_f() is then not common between SPL and u-boot
proper anymore, thus common.c is removed, as it just contained said
function.
Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Michael Walle [Thu, 7 Jan 2021 23:08:58 +0000 (00:08 +0100)]
board: sl28: add network variant 2 support
Although this variant has two external network ports, they are not (yet)
supported by the bootloader because they are connected via an internal
network switch. Otherwise its the same as the other variants.
Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Michael Walle [Thu, 7 Jan 2021 23:08:57 +0000 (00:08 +0100)]
board: sl28: add network variant 1 support
This variant has one network port connected via RGMII and doesn't have
any TSN capabilities out-of-the-box. Instead it has all four SerDes
lanes available for customer use.
Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Michael Walle [Thu, 7 Jan 2021 23:08:56 +0000 (00:08 +0100)]
board: sl28: move ethernet aliases to variant specific dtsi
The variants differ in their network configuration. Move the first two
network aliases to the proper variant device tree includes. This is in
prepartion for variant 1 and 2 support which has a different network
port mapping. The network aliases for the two internal ports will stay
in the common dtsi because they are present on all board variants.
This might leave a hole if there is no ethernet1 alias. This is
intended.
Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Biwen Li [Thu, 10 Dec 2020 03:02:47 +0000 (11:02 +0800)]
configs: ls1088aqds: add COMMON_ENV to fix distroboot
Add COMMON_ENV(kernelheader_addr_r, fdtheader_addr_r,
kernel_addr_r, fdt_addr_r, load_addr)
to fix a bug that failed to boot to ubuntu
Failed log as follows,
## Executing script at 80000000
load - load binary file from a filesystemUsage:
load <interface> [<dev[:part]> [<addr> [<filename> [bytes [pos]]]]]
- Load binary file filename from partition part on device
type interface instance dev to address addr in memory.
bytes gives the size to load in bytes.
If bytes is 0 or omitted, the file is read until the end.
pos gives the file byte position to start reading from.
If pos is 0 or omitted, the file is read from the start.
...
Bad Linux ARM64 Image magic!
SCRIPT FAILED: continuing...
Signed-off-by: Biwen Li <biwen.li@nxp.com>
[Updated description] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Ioana Ciornei [Wed, 9 Dec 2020 11:31:58 +0000 (13:31 +0200)]
net: memac_phy: add a timeout to MDIO operations
We have encountered circumstances when a board design does not include
pull-up resistors on the external MDIO buses which are not used. This
leads to the MDIO data line not being pulled-up, thus the MDIO controller
will always see the line as busy.
Without a timeout in the MDIO bus driver, the execution is stuck in an
infinite loop when any access is initiated on that external bus.
Add a timeout in the driver so that we are protected in this
circumstance. This is similar to what is being done in the Linux
xgmac_mdio driver.
Michael Walle [Wed, 9 Dec 2020 09:53:26 +0000 (10:53 +0100)]
board: kontron: disable flash unlock all
Although the status register is protected by the hardware write
protection, there is a hardware jumper to disable that hardware write
protection. Thus if a user would set this jumper any u-boot start would
disable the write protection altogether.
Circumvent that by not disabling the write protection in the first
place.
Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Michael Walle [Wed, 9 Dec 2020 09:53:25 +0000 (10:53 +0100)]
mtd: spi-nor: add unlock all config option
Provide an explicit configuration option to disable default "unlock all"
of any flash chip which supports locking. It doesn't make sense to
automatically unprotect the entire flash on each u-boot startup if the
block protection bits are actually used.
Traditionally, the unlock was there to be able to write to flash devices
which powered-up with the block protection bits set. Over time this
feature creeped into all flash devices which support locking.
For a more detailed description and discussion see:
https://lore.kernel.org/linux-mtd/20201203162959.29589-8-michael@walle.cc/
Keep things simple in u-boot and just provide a configration option to
disable this behavior which can be set per board.
Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
- introduces some standard sysinfo options as a source, e.g. to read
strapping pins to determine the board revision
- allows the U-Boot version number to be included
- allows the version number to be provided programmatically, e.g. to
support the build system adding information after U-Boot is built
Simon Glass [Fri, 5 Feb 2021 04:17:22 +0000 (21:17 -0700)]
x86: coral: Add sysinfo ops
These ops are missing at present which is not permitted. Add an empty
operation struct.
Note: If the uclass requires operations then the drivers should provide
them. Otherwise, checking for missing operations must be done in every
uclass operation, so it adds to code size.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Fri, 5 Feb 2021 04:17:21 +0000 (21:17 -0700)]
sysinfo: Move #ifdef so that operations are always defined
At present the struct is not available unless SYSINFO is enabled. This is
annoying since code it is not possible to use compile-time checks like
CONFIG_IS_ENABLED(SYSINFO) with this header.
Fix it by moving the #ifdef.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Fri, 5 Feb 2021 04:17:20 +0000 (21:17 -0700)]
smbios: Add more options for the BIOS version string
At present the version string is obtained from PLAIN_VERSION. Some boards
may want to configure this using the device tree, since the build system
can more easily insert things there after U-Boot itself is built. Add this
option to the code.
Also in some cases the version needs to be generated programmatically,
such as when it is stored elsewhere in the ROM and must be read first.
To handle this, keep a pointer around so that it can be updated later.
This works by storing the last string in the context, since it is easier
than passing out a little-used extra parameter.
Provide a function to update the version string.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Fri, 5 Feb 2021 04:17:18 +0000 (21:17 -0700)]
smbios: Drop the eos parameter
We can store this in the context and avoid passing it to each function.
This makes it easier to follow and will also allow keeping track of the
end of the string table (in future patches).
Add an 'eos' field to the context and create a function to set it up.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Fri, 5 Feb 2021 04:17:17 +0000 (21:17 -0700)]
smbios: Use a struct to keep track of context
At present we pass the ofnode to each function. We also pass the 'eos'
pointer for adding new strings. We don't track the current end of the
string table, so have smbios_string_table_len() to find that.
The code can be made more efficient if it keeps information in a
context struct. This also makes it easier to add more features.
As a first step, switch the ofnode parameter to be a context pointer.
Update smbios_add_prop() at the same time to avoid changing the same
lines of code in consecutive patches.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Fri, 5 Feb 2021 04:17:13 +0000 (21:17 -0700)]
Makefile: Provide numeric versions
For SMBIOS we want to store the numeric version numbers in the tables. It
does not make sense to parse the strings. Instead, add new #defines with
the version and patchlevel.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tom Rini [Fri, 5 Feb 2021 14:39:31 +0000 (09:39 -0500)]
Merge tag 'ti-v2021.04-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-ti
- Sync DTS from Linux kernel for all K3 platforms
- Add MMC higher speed nodes for AM65x, J721e, J7200
- Convert Nokia RX-51 to use CONFIG_DM_MMC
- Minor fixes for LEGO MINDSTORMS
Tom Rini [Thu, 4 Feb 2021 22:35:50 +0000 (17:35 -0500)]
Merge tag 'efi-2021-04-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2021-04-rc2
Bug fixes:
* do not allow creating of files with filenames on FAT file system
* install UEFI System Partition GUID on ESP handle
* in dtbdump.efi test tool use GUID to find ESP handle
Documentation:
* man-page for load command
* describe end of life of plat_auto
The Load File2 protocol exposes a device path with a VenMedia() node. Hence
our implementation of the device path to text protocol should support this
node.
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If dtbdump.efi is loaded from memory when calling LoadImage the loaded
image protocol will not indicate the partition from where it was loaded.
In this case use the EFI system partition for the 'load' and 'save'
commands.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
efi_loader: only check size if EFI_DT_APPLY_FIXUPS
In the implementation of the EFI_DT_FIXUP_PROTOCOL:
* Only check the buffer size when EFI_DT_APPLY_FIXUPS is set.
* In this case the field totalsize of the device-tree may not exceed the
buffer size.
* Install device-tree only if EFI_DT_INSTALL_TABLE is set.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Lokesh Vutla [Mon, 1 Feb 2021 05:56:41 +0000 (11:26 +0530)]
arm: dts: k3-j7200: Sync Linux v5.11-rc6 dts into U-Boot
Sync all J7200 related v5.11-rc6 Linux kernel dts into U-Boot.
MCU R5F nodes are not yet added in Linux kernel yet but were added
in U-Boot. In order to avoid regressions, r5f nodes are kept intact.
These will be added in kernel in future.
Lokesh Vutla [Mon, 1 Feb 2021 05:56:40 +0000 (11:26 +0530)]
arm: dts: k3-j721e: Sync Linux v5.11-rc6 dts into U-Boot
Sync all J721e related v5.11-rc6 Linux kernel dts into U-Boot.
HBMC nodes are not yet added in Linux kernel yet but were added
in U-Boot. In order to avoid any regressions, hbmc nodes are kept
intact. These will be added in kernel in future.
Faiz Abbas [Thu, 4 Feb 2021 09:41:04 +0000 (15:11 +0530)]
arm: dts: k3-am654-base-board: Limit Sd card to High speed modes
There's an issue with the base board in which the power cycle
circuit takes way longer to power down than expected by mmc core.
code. This prevents the card from enumerating in UHS modes.
Disable UHS modes for this board until a new board revision fixes
the issue.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Faiz Abbas [Thu, 4 Feb 2021 09:40:56 +0000 (15:10 +0530)]
arm: dts: k3-am65: Fix mmc nodes
Because of fundamental interface issues in am65x pg1, only the
initial sdhci1 node at 25 MHz was added in the u-boot.dtsi
from which both the base-board.dts and r5-base-board.dts
inherit the node. Move the node out to k3-am65-main.dtsi
where it belongs and add the board specific properties
in base-board.dts and r5-base-board.dts
This ensures dts compatibility with the kernel dts in the
base-board.dts and enables the SD card interface at 50 MHz
and High Speed mode
While we are here, also fix the main_mmc0_pins_default
property to be included and inherit from the base-board.dts
instead of the u-boot.dtsi
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Faiz Abbas [Thu, 4 Feb 2021 09:40:54 +0000 (15:10 +0530)]
mmc: am654_sdhci: Fix HISPD bit configuration in some lower speed modes
According to the AM654x Data Manual[1], the setup timing in lower speed
modes can only be met if the controller uses a falling edge data launch.
To ensure this, the HIGH_SPEED_ENA (HOST_CONTROL[2]) bit should be
cleared in default speed, SD high speed, MMC high speed, SDR12 and SDR25
speed modes.
Use the sdhci writeb callback to implement this condition.
Faiz Abbas [Thu, 4 Feb 2021 09:40:53 +0000 (15:10 +0530)]
mmc: am654_sdhci: Add support for software tuning
With the new SW tuning App note[1], a custom tuning algorithm is
required for eMMC HS200, HS400 and SD card UHS modes. The algorithm
involves running through the 32 possible input tap delay values and
sending the appropriate tuning command (CMD19/21) for each of them
to get a fail or pass result for each of the values. Typically, the
range will have a small contiguous failing window. Considering the
tuning range as a circular buffer, the algorithm then sets a final
tuned value directly opposite to the failing window.
Faiz Abbas [Thu, 4 Feb 2021 09:40:51 +0000 (15:10 +0530)]
mmc: am654_sdhci: Add support for input tap delay
DLL need only be enabled for speed modes and clock frequencies at or
above 50 MHz. For speed modes that don't enable the DLL, we need to
configure a static input delay value. This involves reading an optional
itap-del-sel-* value from the device tree and configuring it for the
appropriate speed mode.
Therefore, move all dll configurations to their own functions and gate it
with 50 MHz speed and a minimum mode. If both these conditions are not
satisfied then configure delay chain modes.
Faiz Abbas [Thu, 4 Feb 2021 09:40:47 +0000 (15:10 +0530)]
mmc: am654_sdhci: Unconditionally switch off DLL in the beginning of ios_post()
There are some speed modes that work without switching the dll on.
Unconditionally switch off the DLL before setting clock frequency to
support this case. The software will automatically enable DLL for speed
modes that require it. This also means the dll_on priv data member is no
longer required.
Suman Anna [Wed, 27 Jan 2021 00:20:56 +0000 (18:20 -0600)]
remoteproc: k3_r5: Sync to upstreamed kernel DT property names
The K3 R5F remoteproc driver in U-Boot was upstreamed prior to the
equivalent remoteproc driver in the Linux kernel. Some of the DT
properties used in U-Boot got upstreamed using different names
in Linux kernel.
The modified property names include the R5F cluster mode configuration
property "lockstep-mode"; and three different individual R5F core config
properties - "atcm-enable", "btcm-enable" and "loczrama". The property
names were updated as follows:
lockstep-mode => ti,cluster-mode
atcm-enable => ti,atcm-enable
btcm-enable => ti,btcm-enable
loczrama => ti,loczrama
Update the K3 R5F remoteproc driver, the corresponding binding, and
all the existing usage in AM65x, J721E and J7200 dts files all at
once to use the new properties and to not break any bisectability.
configs: am65x_evm_a53: Enable config for phandle check while getting sequence number
AM65x SoC has two USB subsystems and their corresponding device tree nodes
have the same name but different path. While allocating sequence numbers
for these device tree nodes using alias, phandles can be used to
distinguish them.
Enable config for phandle check while getting sequence number to
distinguish the USB device tree nodes.
David Lechner [Mon, 11 Jan 2021 19:24:46 +0000 (13:24 -0600)]
configs: legoev3: disable CONFIG_NET
This disables the CONFIG_NET setting for LEGO MINDSTORMS EV3. This board
does not have any built-in networking, so it does not make sense to
enable this feature.
This also fixes the warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: David Lechner <david@lechnology.com>
David Lechner [Mon, 11 Jan 2021 19:24:45 +0000 (13:24 -0600)]
ARM: legoev3: drop bi_arch_number
This drops assigning bi_arch_number on LEGO MINDSTORMS EV3. This board
never had its own unique number and since we are using device tree,
we no longer need to pass an arch number to Linux.
Signed-off-by: David Lechner <david@lechnology.com>
David Lechner [Mon, 11 Jan 2021 19:24:44 +0000 (13:24 -0600)]
ARM: legoev3: set serial# env var
This sets the serial# environmet variable instead of using ATAGs on
LEGO MINDSTORMS EV3.
Also fix some nomenclature while we are touching this code (Bluetooth
address is not the same as MAC address, EEPROM version is not the same
as board version).
Signed-off-by: David Lechner <david@lechnology.com>
Pali Rohár [Sat, 16 Jan 2021 00:04:54 +0000 (01:04 +0100)]
Nokia RX-51: Convert to CONFIG_DM_MMC
Move twl4030_power_mmc_init() from board_mmc_power_init() to misc_init_r()
and disable CONFIG_SYS_MALLOC_F. Otherwise U-Boot cannot initialize MMC.
Also disable CONFIG_CMD_SLEEP CONFIG_DM_DEVICE_REMOVE CONFIG_MMC_VERBOSE to
free some space.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Tom Rini <trini@konsulko.com>
Kory Maincent [Tue, 2 Feb 2021 15:42:29 +0000 (16:42 +0100)]
cmd: pxe_utils: sysboot: Add zboot support to boot x86 Linux kernel image
Add "zboot" command to the list of supported boot in the
label_boot function.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: add component tags in the summary] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Kory Maincent [Tue, 2 Feb 2021 15:42:28 +0000 (16:42 +0100)]
cmd: pxe_utils: Replace ifdef by IS_ENABLED
Replace all the macro ifdef by IS_ENABLED.
All of these configs are set in the defconfig files and not in the
include board headers files.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: keep the preprocessor case unchanged] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Kory Maincent [Tue, 2 Feb 2021 15:42:27 +0000 (16:42 +0100)]
command.h: Remove extern from the header
Remove the extern of the header because they are useless.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
[bmeng: minor edit on the commit message] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Bin Meng [Tue, 2 Feb 2021 07:04:47 +0000 (15:04 +0800)]
x86: qemu: Fix broken multi-core boot
Unfortunately the multi-core boot for QEMU x86 has been broken since
commit 77a5e2d3bc61 ("x86: mp_init: Set up the CPU numbers at the start").
In order to support QEMU x86 multi-core boot, the /cpus node must be
bound before any actual fix up in qemu_cpu_fixup(). This adds the
uclass_get() call to ensure this, just like what was done before.
Fixes: 77a5e2d3bc61 ("x86: mp_init: Set up the CPU numbers at the start") Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
The FAT32 File System Specification [1] requires leading and trailing
spaces as well as trailing periods of long names to be ignored.
[1]
Microsoft Extensible Firmware Initiative
FAT32 File System Specification
Version 1.03, December 6, 2000
Microsoft Corporation
https://www.win.tue.nl/~aeb/linux/fs/fat/fatgen103.pdf
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Bin Meng [Sun, 31 Jan 2021 12:36:06 +0000 (20:36 +0800)]
bdinfo: Change to use bdinfo_print_num_ll() where the number could be 64-bit
There are some calls to bdinfo_print_num_l() with parameters that
could be a 64-bit value on a 32-bit system. Change those calls to
use bdinfo_print_num_ll() instead.
Signed-off-by: Bin Meng <bin.meng@windriver.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Bin Meng [Sun, 31 Jan 2021 12:36:05 +0000 (20:36 +0800)]
bdinfo: Rename function names to be clearer
At present we have bdinfo_print_num() to print unsigned long numbers.
We also have print_phys_addr() which accept numbers that might be
64-bit on a 32-bit platform.
Bin Meng [Sun, 31 Jan 2021 12:36:04 +0000 (20:36 +0800)]
riscv: Change phys_addr_t and phys_size_t to 64-bit
phys_addr_t and phys_size_t are currently defined as `unsigned long`,
but RV32 supports 34-bit physical address, hence both phys_addr_t and
phys_size_t should be defined to 64-bit using `unsigned long long`.
Bin Meng [Sun, 31 Jan 2021 12:36:03 +0000 (20:36 +0800)]
fdtdec: Cast prior_stage_fdt_address with uintptr_t
At present prior_stage_fdt_address is declared as phys_addr_t. On
a 32-bit platform where phys_addr_t can be 64-bit, assigning its
value to gd->fdt_blob which is a pointer, can cause warnings.
Cast it to uintptr_t before the assignment.
Signed-off-by: Bin Meng <bin.meng@windriver.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Bin Meng [Sun, 31 Jan 2021 12:36:02 +0000 (20:36 +0800)]
net: ftmac100: Cast priv->iobase with uintptr_t
priv->iobase was declared as phys_addr_t which is now a 64-bit
address. In a 32-bit build, this causes the following warning
seen when building ftmac100.c:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Bin Meng [Sun, 31 Jan 2021 12:36:00 +0000 (20:36 +0800)]
serial: sifive: Cast dev_read_addr() with uintptr_t
dev_read_addr() returns fdt_addr_t which is now a 64-bit address.
In a 32-bit build, this causes the following warning seen when
building serial_sifive.c:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Bin Meng [Sun, 31 Jan 2021 12:35:57 +0000 (20:35 +0800)]
riscv: Adjust board_get_usable_ram_top() for 32-bit
When testing QEMU RISC-V 'virt' machine with a 2 GiB memory
configuration, it was discovered gd->ram_top is assigned to
value zero in setup_dest_addr().
While gd->ram_top should not be declared as type `unsigned long`,
which will be updated in a future patch, the current logic in
board_get_usable_ram_top() can be updated to cover both 64-bit
and 32-bit RISC-V.
projects / u-boot.git / log
