Jagan Teki [Tue, 21 Jul 2020 15:06:04 +0000 (20:36 +0530)]
rockchip: roc-rk3399-pc: Set LED only during POR and pwr_key=y
ROC-RK3399-PC has specific set of configurations for
on-board led setup.
Due to easiness for user to know the state of the board
roc-rk339-pc board code will setup the low power led
on/off, and waiting for user to press power key and then
glow full power led.
All this needs to happen only during power-on-reset not
for soft reset or WDT.
Also, it is not a proper usage to ask the user to press
the Power key if the board connected remotely, so add
the environment variable 'pwr_key' to check as well.
So, user need to press Power key only
- during POR
- pwr_key=y
Tested-by: Suniel Mahesh <sunil@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jagan Teki [Tue, 21 Jul 2020 15:06:03 +0000 (20:36 +0530)]
rockchip: Separate the reset cause from display cpuinfo
reset cause is a generic functionality based on the soc
cru registers in rockchip. This can be used for printing
the cause of reset in cpuinfo or some other place where
reset cause is needed.
Other than cpuinfo, reset cause can also be using during
bootcount for checking the specific reset cause and glow
the led based on the reset cause.
So, let's separate the reset cause code from cpuinfo, and
add a check to build it for rk3399, rk3288 since these two
soc are supporting reset cause as of now.
Tested-by: Suniel Mahesh <sunil@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jagan Teki [Tue, 21 Jul 2020 15:06:02 +0000 (20:36 +0530)]
rockchip: Don't clear the reset status reg
reset reason can be used several stages of U-Boot bootloader
like SPL, U-Boot proper based on the requirements.
Clearing the status register end of get_reset_cause will end
up showing the wrong reset cause when it read the second time.
For example, if board resets, SPL reads the reset status as
RST whereas U-Boot proper reads the status as POR.
However, based on the latest testing clearing reset status
won't be required for determine the last reset cause or
following resets.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jagan Teki [Tue, 21 Jul 2020 15:06:01 +0000 (20:36 +0530)]
rockchip: roc-rk3399-pc: Add custom led_setup()
roc-rk3399-pc has some specific requirements to support LEDS,
environment. board detection and etc prior to U-Boot proper.
So as of now SPL would be a better stage for these custom board
requirements to support unlike TPL. Adding few of these custom
requirements like LEDS in TPL would require extra code pulling
and also the size of TPL can grow.
So, this patch moves the leds code from TPL into SPL Board init
led_setup code.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(split tpl.c change as separate patch) Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Jagan Teki [Mon, 20 Jul 2020 18:55:48 +0000 (00:25 +0530)]
arm64: dts: rockchip: Add ROCKPi 4A/4B support
Rock PI 4 has 3 variants of hardware platforms called
RockPI 4A, 4B, and 4C.
- Rock PI 4A has no Wif/BT.
- Rock PI 4B has AP6256 Wifi/BT, PoE.
- Rock PI 4C has AP6256 Wifi/BT, PoE, miniDP, USB Host enable
GPIO pin change compared to 4B, 4C
So move common nodes, properties into dtsi file and include
on respective variant dts files.
Use 4B dts into default rock-pi-4 defconfig until we find any
solution for dynamic detection of these variants.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Wed, 22 Jul 2020 11:46:19 +0000 (19:46 +0800)]
rockchip: firefly-rk3399: enable CONFIG_USB_DWC3
To fix below build error:
drivers/usb/host/built-in.o: In function `xhci_dwc3_remove':
drivers/usb/host/xhci-dwc3.c:174: undefined reference to `dwc3_shutdown_phy'
drivers/usb/host/built-in.o: In function `xhci_dwc3_probe':
drivers/usb/host/xhci-dwc3.c:130: undefined reference to `dwc3_setup_phy'
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Sat, 18 Jul 2020 14:45:19 +0000 (22:45 +0800)]
rockchip: rk3399: Add default env to support compressed kernel Image
Add default kernel_comp_addr_r and kernel_comp_size to support boot
from compressed kernel Image, this space is temporarily used during
decompress according to README.distro.
Reported-by: Tian Yuanhao <tianyuanhao@aliyun.com> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Alex Bee [Tue, 14 Jul 2020 23:03:31 +0000 (01:03 +0200)]
rockchip: sdram: fix dram_init_banksize
Currently 2.5 GB is calculated as DRAM size for a 1 GB RK322x board
if CONFIG_SPL_OPTEE is set. This is troublesome when booting a
linux kernel since this size will be injected in FDT of the kernel.
gd->bd->bi_dram[0].start (which is basically CONFIG_SYS_SDRAM_BASE)
must not be taken into consideration for calculation of second bank
size, since this offset is already included in calculation of "top".
After applying this patch 992 MB (1024 MB - 32 MB reserved for
optee-os) is correctly calculated and has also been verified on
2 GB boards.
Signed-off-by: Alex Bee <knaerzche@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Mon, 20 Jul 2020 10:34:12 +0000 (18:34 +0800)]
rockchip: ram: fix debug funcfion define when RAM_ROCKCHIP_DEBUG not set
The empty function define should not be in the header file, or else the
build will error with function multi definition after CONFIG_RAM_ROCKCHIP_DEBUG
is disabled.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
rockchip: rock64-rk3328_defconfig: Add SPI Flash support
Add U-Boot SPI Flash support for the PINE64 Rock64 board
Signed-off-by: Johannes Krottmayer <krjdev@gmail.com> Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add U-Boot SPI Flash support for the PINE64 Rock64 board
Signed-off-by: Johannes Krottmayer <krjdev@gmail.com> Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Johannes Krottmayer <krjdev@gmail.com> Cc: Kever Yang <kever.yang@rock-chips.com> Cc: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(fix checkpatch error for code ident) Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Johannes Krottmayer <krjdev@gmail.com> Cc: Kever Yang <kever.yang@rock-chips.com> Cc: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
drivers: clk: rockchip: clk_rk3328: Add SPI support
Add SPI support for the RK3328 clock driver
Signed-off-by: Johannes Krottmayer <krjdev@gmail.com> Cc: Kever Yang <kever.yang@rock-chips.com> Cc: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jagan Teki [Tue, 7 Jul 2020 13:50:44 +0000 (19:20 +0530)]
rockchip: rock-pi-4: Enable USB3 Host
Enable USB3.0 Host support for RockPI-4 boards.
Note that the Upper USB3.0 port is marked as otg and
lower USB3.0 port marked as host, so this below log
capture when USB3.0 mass storage plug in at lower
USB 3.0 port.
Log:
Bus usb@fe380000: USB EHCI 1.00
Bus usb@fe3c0000: USB EHCI 1.00
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe380000 for devices... 1 USB Device(s) found
scanning bus usb@fe3c0000 for devices... 1 USB Device(s) found
scanning bus dwc3 for devices... 1 USB Device(s) found
scanning bus dwc3 for devices... cannot reset port 1!?
2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
=> usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
Tom Rini [Fri, 17 Jul 2020 20:08:54 +0000 (16:08 -0400)]
Merge branch '2020-07-17-misc-fixes'
A large number of assorted fixes, including but not limited to:
- Correct fixdep and CONFIG_IS_ENABLED(...)
- lz4 on big endian
- Assorted LMB hardening
- Remove bd_t typedef
Martin Kaistra [Mon, 13 Jul 2020 12:40:02 +0000 (14:40 +0200)]
mtd: mtdpart: use uint64_t instead of int for cur_off
The types of "offset" and "size" of "struct mtd_partition" are uint64_t,
while mtd_parse_partitions() uses int to work with these values. When
the offset reaches 2GB, it is interpreted as a negative value, which
leads to error messages like
mtd: partition "<partition name>" is out of reach -- disabled
eg. when using the "ubi part" command.
Fix this by using uint64_t for cur_off and cur_sz.
Signed-off-by: Martin Kaistra <martin.kaistra@linutronix.de> Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> Reviewed-by: Heiko Schocher <hs@denx.de>
Stephen Warren [Wed, 8 Jul 2020 21:45:56 +0000 (15:45 -0600)]
fixdep: fix CONFIG_IS_ENABLED etc. handling
When fixdep detects CONFIG_IS_ENABLED and other similar macros, it must
parse the macro parameter to determine which actual CONFIG_ option is
being referenced. This involves moving a pointer forward through the
entire CONFIG_ option "word". Currently, the code uses variable q to walk
through the word, but doesn't actually initialize it to point at the
parameter before doing so. Consequently, the walking process immediately
fails since it sees the macro invocatoins's ( rather than the expected
alpha-numeric characters in the macro parameter. Fix this by adding the
missing initialization.
Fixes: 67f2ee86ccbe ("kbuild: fixdep: Resync this with v4.17") Fixes: 7012865e961c ("gpio: fix test.py for gpio label lookup") Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Since commit 4b0bcfa7c4ec (Kconfig: Migrate CONFIG_BOOTM_* options),
the config_defaults.h file has been void of any actual content - and
these days, "sane defaults for everyone" is achieved by appropriate
default values in Kconfig. Remove it, and thus make every translation
unit process one less header file.
Chin Liang See [Wed, 24 Jun 2020 08:31:08 +0000 (16:31 +0800)]
lib: zlib: Remove offset pointer optimization in inftrees.c
This fixes the CVE-2016-9840. Commit imported from [1].
inftrees.c was subtracting an offset from a pointer to an array,
in order to provide a pointer that allowed indexing starting at
the offset. This is not compliant with the C standard, for which
the behavior of a pointer decremented before its allocated memory
is undefined. Per the recommendation of a security audit of the
zlib code by Trail of Bits and TrustInSoft, in support of the
Mozilla Foundation, this tiny optimization was removed, in order
to avoid the possibility of undefined behavior.
Signed-off-by: Mark Adler <madler@alumni.caltech.edu> Signed-off-by: Chin Liang See <chin.liang.see@intel.com> Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Thomas Schaefer [Tue, 16 Jun 2020 20:03:52 +0000 (22:03 +0200)]
spl: fix ext4fs_mount return code handling
- Despite other ext4 filesystem functions, ext4fs_mount returns
0 in case of error.
- This leads to u-boot crash in case that an SD card
with valid partition table but without ext4 filesystem created
in a partition is found on SD card.
- Fix this by returning a proper error code of '-1' from spl_load_image_ext
function in case of ext4fs_mount error.
Signed-off-by: Thomas Schaefer <thomas.schaefer@kontron.com>
[hthiery: slightly reword the commit message] Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Tero Kristo [Fri, 12 Jun 2020 12:41:21 +0000 (15:41 +0300)]
cmd: booti: convert the debug print about image move to printf
Moving of the OS image may have some nasty side effects like corrupting
DTB. Convert the current debug print to printf so that the relocation of
the OS is always obvious to the user.
Tero Kristo [Fri, 12 Jun 2020 12:41:20 +0000 (15:41 +0300)]
common: bootm: add checks to verify if ramdisk / fdtimage overlaps OS image
These cases are typically fatal and are difficult to debug for random
users. Add checks for detecting overlapping images and abort if overlap
is detected.
Tero Kristo [Fri, 12 Jun 2020 12:41:19 +0000 (15:41 +0300)]
image: fdt: bail out with error if no boot time FDT image found
Currently the boot continues if the FDT image is clearly corrupted,
which just causes the loaded OS to hang. Abort boot properly if the FDT
is corrupted.
So the magic is ok, but the version check fails, also some reserved
bits are apparently set. But that's because the code interprets the
"flags" and "block_descriptor" bytes wrongly:
Using bit-fields to access individual bits of an "on the wire" format
is not portable, not even when restricted to the C flavour implemented
by gcc. Quoting the gcc manual:
* 'The order of allocation of bit-fields within a unit (C90 6.5.2.1,
C99 and C11 6.7.2.1).'
Determined by ABI.
and indeed, the PPC Processor ABI supplement says
* Bit-fields are allocated from right to left (least to most
significant) on Little-Endian implementations and from left to
right (most to least significant) on Big-Endian implementations.
The upstream code (github.com/lz4/lz4) uses explicit shifts and masks
for encoding/decoding:
/* Flags */
{ U32 const FLG = srcPtr[4];
U32 const version = (FLG>>6) & _2BITS;
blockChecksumFlag = (FLG>>4) & _1BIT;
blockMode = (FLG>>5) & _1BIT;
contentSizeFlag = (FLG>>3) & _1BIT;
contentChecksumFlag = (FLG>>2) & _1BIT;
dictIDFlag = FLG & _1BIT;
/* validate */
if (((FLG>>1)&_1BIT) != 0) return err0r(LZ4F_ERROR_reservedFlag_set); /* Reserved bit */
if (version != 1) return err0r(LZ4F_ERROR_headerVersion_wrong); /* Version Number, only supported value */
}
Do the same here, and while at it, be more careful to use unaligned
accessors to what is most likely unaligned. Also update the comment to
make it clear that it only refers to the lz4.c file, not the following
code of lz4_wrapper.c.
This has been tested partly, of course, by seeing that my
lz4-compressed kernel now boots, partly by running the (de)compression
test-suite in the (x86_64) sandbox - i.e., it should still work just
fine on little-endian hosts.
Reviewed-by: Julius Werner <jwerner@chromium.org> Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
- New timer API to allow delays with a 32-bit microsecond timer
- Add dynamic ACPI structs (DSDT/SSDT) generations to the DM core
- x86: Enable ACPI table generation by default
- x86: Enable the copy framebuffer on Coral
- x86: A few fixes to FSP2 with ApolloLake
- x86: Drop setup_pcat_compatibility()
- x86: Primary-to-Sideband Bus minor fixes
Tom Rini [Fri, 17 Jul 2020 12:04:28 +0000 (08:04 -0400)]
Merge tag 'u-boot-imx-20200716' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
i.MX for 2020.10
----------------
- i.MX DDR driver fix/update for i.MX8M
- i.MX pinctrl driver fix.
- Use arm_smccc_smc to remove imx sip function
- i.MX8M clk update
- support booting aarch32 kernel on aarch64 hardware
- fused part support for i.MX8MP
- imx6: pcm058 to DM
Simon Glass [Fri, 17 Jul 2020 03:22:38 +0000 (21:22 -0600)]
x86: Rename board_final_cleanup() to board_final_init()
This function sounds like something that is called when U-Boot is about to
jump to Linux. In fact it is an init function.
Rename it to reduce confusion.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Simon Glass [Fri, 17 Jul 2020 03:22:37 +0000 (21:22 -0600)]
x86: acpi: Correct the version of the MADT
Currently U-Boot implements version 2 but reports version 4. Correct it.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Simon Glass [Fri, 17 Jul 2020 03:22:35 +0000 (21:22 -0600)]
x86: Update the comment about booting for FSP2
The comment here applies only to FSP1, so update it.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Simon Glass [Fri, 17 Jul 2020 03:22:34 +0000 (21:22 -0600)]
x86: Store the coreboot table address in global_data
At present this information is used to locate and parse the tables but is
not stored. Store it so that we can display it to the user, e.g. with the
'bdinfo' command.
Note that now the GD_FLG_SKIP_LL_INIT flag is set in get_coreboot_info(),
so it is always set when booting from coreboot.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Simon Glass [Fri, 17 Jul 2020 03:22:33 +0000 (21:22 -0600)]
x86: apl: Adjust FSP-M code to avoid hard-coded address
Update this code to calculate the address to use, rather than hard-coding
it. Obtain the requested stack size from the FSP.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Fri, 17 Jul 2020 03:22:32 +0000 (21:22 -0600)]
x86: apl: Set the correct boot mode in the FSP-M code
If there is MRC information we should run FSP-M with a different
boot_mode flag since it is supposed to do a 'fast path' through the
memory init. Fix this.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Fri, 17 Jul 2020 03:22:31 +0000 (21:22 -0600)]
x86: Add debugging to table writing
Writing tables is currently pretty opaque. Add a bit of debugging to the
process so we can see what tables are written and where they start/end in
memory.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Simon Glass [Fri, 17 Jul 2020 03:22:30 +0000 (21:22 -0600)]
x86: apl: Fix save/restore of ITSS priorities
The FSP-S changes the ITSS priorities. The code that tries to save it
before running FSP-S and restore it afterwards does not work as U-Boot
relocates in between the save and restore. This means that the driver
data saved before relocation is lost and the new driver just sees zeroes.
Fix this by allocating space in the relocated memory for the ITSS data.
Save it there and access it from the driver after relocation.
This fixes interrupt handling on coral.
Also drop the log_msg_ret() in irq_first_device_type() since this function
can be called speculatively in places where we are not sure if there is
an interrupt controller of that type. The resulting log errors are
confusing when there is no error.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Simon Glass [Wed, 8 Jul 2020 03:32:34 +0000 (21:32 -0600)]
x86: irq: Support flags for acpi_gpe
This binding currently has a flags cell but it is not used. Make use of it
to create ACPI tables for interrupts.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Simon Glass [Wed, 8 Jul 2020 03:32:33 +0000 (21:32 -0600)]
pmc: Move common registers to the header file
These registers need to be accesses from ACPI code, so move them to the
header file.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Wed, 8 Jul 2020 03:32:32 +0000 (21:32 -0600)]
x86: apl: Hide the p2sb on exit from U-Boot
This confuses Linux's PCI probing so needs to be hidden when booting
Linux. Add a remove() method to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Tested-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Simon Glass [Wed, 8 Jul 2020 03:32:31 +0000 (21:32 -0600)]
x86: apl: Support set_hide() in p2sb driver
Add support for this new method in the driver and in the fsp-s setup.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Tested-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Simon Glass [Wed, 8 Jul 2020 03:32:30 +0000 (21:32 -0600)]
p2sb: Add a method to hide the bus
The P2SB bus needs to be hidden in some cases so that it does not get
auto-configured by Linux. Add a method for this.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Tested-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Simon Glass [Wed, 8 Jul 2020 03:32:29 +0000 (21:32 -0600)]
i2c: designware_i2c: Support ACPI table generation
Update the PCI driver to generate ACPI information so that Linux has the
full information about each I2C bus.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heiko Schocher <hs@denx.de> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
[bmeng: Correct one typo in dw_i2c_gen_speed_config() comments] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Wed, 8 Jul 2020 03:32:24 +0000 (21:32 -0600)]
x86: Add error checking for csrt table generation
Generation of this table can fail, so update the function to return an
error code.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Simon Glass [Wed, 8 Jul 2020 03:32:23 +0000 (21:32 -0600)]
x86: pinctrl: Drop the acpi_path member
This is in the device tree now, so drop the unnecessary field here.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Wed, 8 Jul 2020 03:32:22 +0000 (21:32 -0600)]
x86: pinctrl: Set up itss in the probe() method
At present the itss is probed in the ofdata_to_platdata() method. This is
incorrect since itss is a child of p2sb which itself needs to probe the
pinctrl device. This means that p2sb is effectively not probed when the
itss is probed, so we get the wrong register address from p2sb.
Fix this by moving the itss probe to the correct place.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Simon Glass [Wed, 8 Jul 2020 03:32:21 +0000 (21:32 -0600)]
x86: pinctrl: Add multi-ACPI control
Add a Kconfig to control whether pinctrl is represented as a single ACPI
device or as multiple devices. In the latter case (the default) we should
return the pin number relative to the pinctrl device.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Simon Glass [Wed, 8 Jul 2020 03:32:19 +0000 (21:32 -0600)]
x86: pinctrl: Add a way to get the pinctrl reg address
At present we can query the offset of a pinctrl register within the p2sb.
For ACPI we need to get the actual address of the register. Add a function
to handle this and rename the old one to more accurately reflect its
purpose.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Simon Glass [Wed, 8 Jul 2020 03:32:18 +0000 (21:32 -0600)]
sound: Add an ACPI driver for Maxim MAX98357ac
This chip is used on coral and we need to generate ACPI tables for sound
to make it work. Add a driver that does just this (i.e. at present does
not actually support playing sound).
Signed-off-by: Simon Glass <sjg@chromium.org>
[bmeng: Use the correct acpi_irq_polarity enum number] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Wed, 8 Jul 2020 03:32:17 +0000 (21:32 -0600)]
sound: Add an ACPI driver for Dialog Semicondutor da7219
This chip is used on coral and we need to generate ACPI tables for sound
to make it work. Add a driver that does just this (i.e. at present does
not actually support playing sound).
Simon Glass [Wed, 8 Jul 2020 03:32:16 +0000 (21:32 -0600)]
x86: Add support for building up an NHLT structure
The Intel Non-High-Definition-Audio Link Table (NHLT) table describes the
audio codecs and connections in a system. Various devices can contribute
information to produce the table.
Add functions to allow adding to the structure that is eventually written
to the ACPI tables. Also add the device-tree bindings.
Simon Glass [Wed, 8 Jul 2020 03:32:15 +0000 (21:32 -0600)]
acpi: Support writing named values
Allow writing named integers and strings to the generated ACPI code.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
[bmeng: Fix the "new blank line at EOF" warning] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
projects / u-boot.git / log
