Marek Vasut [Thu, 25 Feb 2021 20:50:59 +0000 (21:50 +0100)]
Makefile: Fix generation of flash.bin u-boot.itb with binman
In case binman is enabled, the u-boot.itb is generated using this tool
and there is no direct u-boot.itb target, but instead the binman tool
must be invoked. Add support for this case.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
Tom Rini [Thu, 29 Apr 2021 15:31:06 +0000 (11:31 -0400)]
Merge tag 'xilinx-for-v2021.07-rc2' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.07-rc2
xilinx:
- Enable saving variables based on bootmode
- Cleanup usb dfu setup and wire it up with usb bootmode
- Fix bootscript address logic
- Remove GD references (spi, Versal)
- Enable capsule update
- Add base support for Marvell OcteonTX2 CN9130 CRB (mostly done
by Kostya)
- Sync Armada 3k/7k/8k SERDES code with Marvell version (misc Marvell
authors)
- pci-aardvark: Fix processing PIO transfers (Pali)
Simon Glass [Sun, 11 Apr 2021 04:27:28 +0000 (16:27 +1200)]
buildman: Use bytes for the environment
At present we sometimes see problems in gitlab where the environment has
0x80 characters or sequences which are not valid UTF-8.
Avoid this by using bytes for the environment, both internal to buildman
and when writing out the 'env' file. Add a test to make sure this works
as expected.
Reported-by: Marek Vasut <marex@denx.de> Fixes: e5fc79ea718 ("buildman: Write the environment out to an 'env' file") Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 11 Apr 2021 04:27:27 +0000 (16:27 +1200)]
buildman: Handle exceptions in threads gracefully
There have been at least a few cases where an exception has occurred in a
thread and resulted in buildman hanging: running out of disk space and
getting a unicode error.
Handle these by collecting a list of exceptions, printing them out and
reporting failure if any are found. Add a test for this.
Sean Anderson [Thu, 8 Apr 2021 21:15:00 +0000 (17:15 -0400)]
dm: core: Fix uninitialized return value from dm_scan_fdt_node
If there are no nodes or if all nodes are disabled, this function would
return err without setting it first. Fix this by initializing err to
zero.
Fixes: 94f7afdf7e ("dm: core: Ignore disabled devices when binding") Signed-off-by: Sean Anderson <sean.anderson@seco.com> Reviewed-by: Simon Glass <sjg@chromium.org>
dm: core: Add address translation in fdt_get_resource
Today of_address_to_resource() is called only in
ofnode_read_resource() for livetree support and
fdt_get_resource() is called when livetree is not supported.
The fdt_get_resource() doesn't do the address translation
so when it is required, but the address translation is done
by ofnode_read_resource() caller, for example in
drivers/firmware/scmi/smt.c::scmi_dt_get_smt_buffer() {
...
ret = ofnode_read_resource(args.node, 0, &resource);
if (ret)
return ret;
Simon Glass [Fri, 2 Apr 2021 22:05:09 +0000 (11:05 +1300)]
binman: Tweak implementation of fmap
Use an interator in two of the fmap tests so it is easier to add new
items. Also check the name first since that is the first indication
that something is wrong. Use a variable for the expected size of the
fmap to avoid repeating the code.
patman: Parse checkpatch by message instead of by line
Parse each empty-line-delimited message separately. This saves having to
deal with all the different line content styles, we only care about the
header ERROR | WARNING | NOTE...
Also make checkpatch print line information for a uboot specific
warning.
Signed-off-by: Evan Benn <evanbenn@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Fri, 26 Feb 2021 12:52:29 +0000 (07:52 -0500)]
Azure/GitLab: Ensure we use requirements.txt for testsuites
Given that test/py/requirements.txt has all required test modules, make
use of that rather than a manual pip install list before running our
assorted tool testsuites.
Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Andy Shevchenko [Thu, 11 Feb 2021 14:40:10 +0000 (16:40 +0200)]
test: Allow simple glob pattern in the test name
When run `ut dm [test name]` allow to use simple pattern to run all tests
started with given prefix. For example, to run all ACPI test cases:
ut dm acpi*
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Mon, 26 Apr 2021 20:19:48 +0000 (08:19 +1200)]
dtoc: Correct dtoc output when testing
At present each invocation of run_steps() updates OUTPUT_FILES_COMMON,
since it does not make a copy of the dict. This is fine for a single
invocation, but for tests, run_steps() is invoked many times.
As a result it may include unwanted items from the previous run, if it
happens that a test runs twice on the same CPU. The problem has not been
noticied previously, as there are few enough tests and enough CPUs that
is is rare for the 'wrong' combination of tests to run together.
Fix this by making a copy of the dict, before updating it. Update the
tests to suit, taking account of the files that are no-longer generated.
With this fix, we no-longer generate files which are not needed for a
particular state of OF_PLATDATA_INST, so the check_instantiate() function
is not needed anymore. It has become dead code and so fails the
code-coverage test (dtoc -T). Remove it.
Simon Glass [Sat, 24 Apr 2021 20:39:32 +0000 (08:39 +1200)]
binman: Correct testSplNoDtb() and Tpl also
These two tests require an ELF image so that symbol information can be
written into the SPL/TPL binary. At present they rely on other tests
having set it up first, but every test must run independently. This can
cause occasional errors in CI.
Fix this by setting up the required files, as other tests do.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
Michal Simek [Mon, 26 Apr 2021 12:26:48 +0000 (14:26 +0200)]
net: phy: xilinx: Break while loop over ethernet phy
The commit 6c993815bbea ("net: phy: xilinx: Be compatible with live OF
tree") change driver behavior to while loop which wasn't correct because
the driver was looping over again and again. The reason was that
ofnode_valid() is taking 0 as correct value.
Fix it by changing while loop to ofnode_for_each_subnode() which is only
loop over available nodes.
Fixes: 6c993815bbea ("net: phy: xilinx: Be compatible with live OF tree") Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Trying to clear PIO_START register when it is non-zero (which indicates
that previous PIO transfer has not finished yet) causes an External
Abort with SError 0xbf000002.
This bug is currently worked around in TF-A by handling External Aborts
in EL3 and ignoring this particular SError.
This workaround was also discussed at:
https://git.trustedfirmware.org/TF-A/trusted-firmware-a.git/commit/?id=3c7dcdac5c50
https://lore.kernel.org/linux-pci/20190316161243.29517-1-repk@triplefau.lt/
https://lore.kernel.org/linux-pci/971be151d24312cc533989a64bd454b4@www.loen.fr/
https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/1541
Implement a proper fix to prevent this External Abort. As it is not
possible to cancel a pending PIO transfer, simply do not start a new one
if previous has not finished yet. In this case return an error to the
caller.
In most cases this SError happens when there is no PCIe card connected
or when PCIe link is down. The reason is that in these cases a PIO
transfer takes about 1.44 seconds. For this reason we also increase the
wait timeout in pcie_advk_wait_pio() to 1.5 seconds.
If PIO read transfer for PCI_VENDOR_ID register times out, or if it
isn't possible to read it yet because previous transfer is not finished,
return Completion Retry Status value instead of failing, to give the
caller a chance to send a new read request.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
phy: marvell: utmi: update utmi config which fixes usb2.0 instability
- Add additional step which enables the Impedance and PLL calibration.
- Enable old squelch detector instead of the new analog squelch detector
circuit and update host disconnect threshold value.
- Update LS TX driver strength coarse and fine adjustment values.
Change-Id: Ifa0a585bfb5ecab0bfa033eed6874ff98b16a7df Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Igal Liberman [Mon, 14 May 2018 08:20:54 +0000 (11:20 +0300)]
phy: marvell: add support for SFI1
In CP115, comphy4 can be configured into SFI port1
(in addition to SFI0). This patch adds the option
described above.
In addition, rename all existing SFI/XFI references:
COMPHY_TYPE_SFI --> COMPHY_TYPE_SFI0
No functional change for exsiting configuration.
Change-Id: If9176222e0080424ba67347fe4d320215b1ba0c0 Signed-off-by: Igal Liberman <igall@marvell.com> Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
phy: marvell: fix pll initialization for second utmi port
According to Design Reference Specification the PHY PLL and Calibration
register from PHY0 are shared for multi-port PHY. PLL control registers
inside other PHY channels are not used.
This commit reworks utmi device tree nodes in a way that common PHY PLL
registers are moved to main utmi node. Accordingly both child nodes
utmi-unit range is reduced and register offsets in utmi_phy.h are updated
to this change.
This fixes issues in scenarios when only utmi port1 was in use, which
resulted with lack of correct pll initialization.
Change-Id: Icc520dfa719f43a09493ab31f671efbe88872097 Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Igal Liberman [Mon, 19 Nov 2018 07:58:32 +0000 (09:58 +0200)]
phy: marvell: cp110: mark u-boot power-off calls
It helps ATF to determine who called power off
function (U-boot/Linux) and act accordingly
Change-Id: Icfc5cbfdba64754496812154272b28c0ff639f0f Signed-off-by: Igal Liberman <igall@marvell.com> Reviewed-by: Grzegorz Jaszczyk <jaz@semihalf.com>
- the default value of comphy pipe selector is set to PCIe (x4)
in case of unconnected comphy the default value remains 0x4
which may lead to several issues with comphy initialization.
- this patch adds SMC call that powers off the comphy lane in case of
unconnected comphy.
Change-Id: I196b2916518dd8df3b159ffa85e2989b8e483087 Signed-off-by: Christine Gharzuzi <chrisg@marvell.com> Signed-off-by: Igal Liberman <igall@marvell.com> Reviewed-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Igal Liberman [Wed, 9 May 2018 15:50:29 +0000 (18:50 +0300)]
phy: marvell: pass sgmii id to firmware
Currently, we don't pass id for SGMII 0/1.
A bug in comphy selector configuration was found (in comphy
firmware), after fixing it, SGMII0/1 have different configuration,
so we need to pass the ID the firmware.
Change-Id: Idcff4029cc9cf018278e493221b64b33574e0d38 Signed-off-by: Igal Liberman <igall@marvell.com> Reviewed-by: Grzegorz Jaszczyk <jaz@semihalf.com>
phy: marvell: cp110: clean up driver after it was moved to atf
Change-Id: I358792a96c13b54e700c05227cc7a8f6bd584694 Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com> Reviewed-by: Igal Liberman <igall@marvell.com>
phy: marvell: cp110: remove both phy and pipe selector configuration
Now the comphy configuration is handled in atf, therefore there is no
need to configure phy or pipe selector in u-boot, it is configured by
atf for each particular pair: lane and mode.
Change-Id: I0bebf8d5ff66dbeb6bf9ef90876195938a8eb705 Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com> Reviewed-by: Igal Liberman <igall@marvell.com>
phy: marvell: cp110: let the firmware perform training for XFI
Replace the XFI training with appropriate SMC call, so the firmware will
perform exact initialization.
Update Stefan 2021-03-23:
Move comphy_smc() function to an earlier place - necessary for the
mainline merge.
Change-Id: I789b130b05529dc80dadcf66aef407d93595b762 Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com> Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Igal Liberman <igall@marvell.com>
phy: marvell: cp110: let the firmware configure comphy for RXAUI
Replace the comphy initialization for RXAUI with appropriate SMC call,
so the firmware will execute required serdes configuration.
Change-Id: Iedae0285fb283e05bb263a8b4ce46e8e7451a309 Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com> Reviewed-by: Igal Liberman <igall@marvell.com>
Marcin Wojtas [Tue, 15 Oct 2019 10:30:39 +0000 (12:30 +0200)]
phy: marvell: cp110: remove unused definitions
Even if comphy types of SATA2/SATA3/SGMII3 and comphy speeds of
1.5G/3G/6.25G were referenced in the driver non configuration (dts)
was using it.
This patch removes unused definitions.
Change-Id: I53ed6f9d3a82b9d18cb4e488bc14d3cf687f9488 Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com> Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Igal Liberman [Tue, 23 Mar 2021 10:57:57 +0000 (11:57 +0100)]
phy: marvell: add RX training command
This patch adds support for running RX training using new command called
"rx_training"
Usage:
rx_training - rx_training <cp id> <comphy id>
RX training allows to improve link quality (for SFI mode)
by running training sequence between us and the link partner,
this allows to reach better link quality then using static configuration.
Change-Id: I818fe67ccaf19a87af50d4c34a9db7d6802049a5 Signed-off-by: Igal Liberman <igall@marvell.com> Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Igal Liberman [Tue, 22 Aug 2017 08:14:22 +0000 (11:14 +0300)]
phy: marvell: fix several minor bugs in comphy_probe
If fdtdec_get_int can't find speed, set COMPHY_SPEED_INVALID
If fdtdec_get_int can't find type, set COMPHY_TYPE_INVALID
Move the error print if phy-type is invalid
Add continue to the probe loop (in a case of invalid phy)
Cosmetic changes
Change-Id: I0c61b40bfe685437426fe907942ed338b7845378 Signed-off-by: Igal Liberman <igall@marvell.com>
phy: marvell: cp110: initialize only enabled UTMI units
UTMI should be initialized only for enabled device tree nodes.
This fix overrides current internal configuration array
entry with the next DT entry data if error is detected
during the current DT entry parsing or the current port
is disabled.
This way the internal configuration structure will only
contain valid ports information obtained from the DT.
Change-Id: I9c43c6a5d234e15ae9005d1c9bc983fc1f3544b8 Signed-off-by: Omri Itach <omrii@marvell.com> Signed-off-by: Ken Ma <make@marvell.com>
Igal Liberman [Wed, 26 Apr 2017 14:20:47 +0000 (17:20 +0300)]
phy: marvell: add missing speed during info prints
In get_speed_string() we have an array (speed_strings[])
which includes all possible speed strings.
This array size and content must be aligned to the speed
defines in comphy_data.h.
This patch adds missing 5.125G speed, aligns speed_strings[]
and fixes incorrect printing when speed > 5.0G.
Change-Id: I9900d23595094be321be0c62fcaa88036324568e Signed-off-by: Igal Liberman <igall@marvell.com>
Igal Liberman [Wed, 26 Apr 2017 12:40:00 +0000 (15:40 +0300)]
phy: marvell: rename comphy related definitions to COMPHY_XX
Currently, all comphy definitions are PHY_TYPE_XX and PHY_SPEEED_XX.
Those definition might be confused with MDIO PHY definitions.
This patch does the following changes:
- PHY_TYPE_XX --> COMPHY_TYPE_XX
- PHY_SPEED_XX --> COMPHY_SPEED_XX
This improves readability, no functional change.
Change-Id: I2bd1d9289ebbc5c16fa80f9870f797ea1bcaf5fa Signed-off-by: Igal Liberman <igall@marvell.com> Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
- For some Marvell SoCs, like armada-3700, there are both
USB host and device controller, but on PHY level the
configuration is the same.
- The new type supports both USB device and USB host
- This patch is cherry-picked from u-boot-2015 as-is.
Change-Id: I01262027edd8ec23391cff6fb409b3009aedfbb9 Signed-off-by: jinghua <jinghua@marvell.com> Signed-off-by: Ken Ma <make@marvell.com> Reviewed-by: Igal Liberman <igall@marvell.com>
Stefan Roese [Tue, 27 Apr 2021 09:05:09 +0000 (11:05 +0200)]
arm: octeontx2: cn9130-crb.dtsi: Disable eth2 for now
Because of the incorrectly supported SGMII_2500 mode, this patch
disables eth2 for now until this issue will be fixed in mainline.
Also fix an incorrect comment.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Konstantin Porotchkin <kostap@marvell.com> Cc: Stefan Chulski <stefanc@marvell.com> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Marek Behun <marek.behun@nic.cz>
arm: octeontx2: Add dtsi/dts files for Octeon TX2 CN9130 CRB
This patch adds the dtsi/dts files needed to support the Marvell
Octeon TX2 CN9130 CRB. This is only the base port with not all
interfaces supported fully.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
arm: armada: configs: Move environment location for mvebu
Move the default environment location to the end of 4MB flash
region. This change allows to accomodate larger flash boot
images making space for forthcoming code changes.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
arm: armada: dts: Use a single dtsi for cp110 die description
Use a single dtsi file for CP110 die instead of master/slave.
Moving to single file will allow miltiple DTSI inclusions with
re-defined CP index and name.
This change will also allow support for SoCs containing more than
two CP110 dies on board.
Move pin control definitions from CP110 DTS to board DTS files
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
power: regulator: Add support for regulator-force-boot-off
Add support for regulator-force-boot-off DT property.
This property can be used by the board/device drivers for
turning off regulators on early init stages as pre-requisite
for the other components initialization.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de> Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Neil Armstrong [Wed, 21 Apr 2021 08:58:01 +0000 (10:58 +0200)]
net: designware: fix PHY reset with DM_MDIO
The dw_eth_pdata is not accessible from the mdio device, it gets the mdio bus plat
leading to random sleeps (-10174464 on Odroid-HC4).
This moves the dw_mdio_reset function to a common one taking the ethernet
device as parameter and use it from the dw_mdio_reset and dm_mdio variant functions.
Fixes: 5160b4567c ("net: designware: add DM_MDIO support") Reported-by: Mark Kettenis <mark.kettenis@xs4all.nl> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Marek Vasut [Sun, 11 Apr 2021 18:47:45 +0000 (20:47 +0200)]
mtd: cfi: Fix PPB lock status readout
According to S26KL512S datasheet [1] and S29GL01GS datasheet [2],
the procedure to read out PPB lock bits is to send the PPB Entry,
PPB Read, Reset/ASO Exit. Currently, the code does send incorrect
PPB Entry, PPB Read and Reset/ASO Exit is completely missing.
The PPB Entry sent is implemented by sending flash_unlock_seq()
and flash_write_cmd(..., FLASH_CMD_READ_ID). This translates to
sequence 0x555:0xaa, 0x2aa:0x55, 0x555:0x90=FLASH_CMD_READ_ID.
However, both [1] and [2] specify the last byte of PPB Entry as
0xc0=AMD_CMD_SET_PPB_ENTRY instead of 0x90=FLASH_CMD_READ_ID,
that is 0x555:0xaa, 0x2aa:0x55, 0x555:0xc0=AMD_CMD_SET_PPB_ENTRY.
Since this does make sense, this patch fixes it and thus also
aligns the code in flash_get_size() with flash_real_protect().
The PPB Read returns 00h in case of Protected state and 01h in case
of Unprotected state, according to [1] Note 83 and [2] Note 17, so
invert the result. Moreover, align the arguments with similar code
in flash_real_protect().
Finally, Reset/ASO Exit command should be executed to exit the PPB
mode, so add the missing reset.
Fixes: 03deff433e ("cfi_flash: Read PPB sector protection from device for AMD/Spansion chips") Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Stefan Roese <sr@denx.de> Reviewed-by: Stefan Roese <sr@denx.de>
Neil Armstrong [Tue, 20 Apr 2021 08:42:26 +0000 (10:42 +0200)]
reset: fix reset_get_by_index_nodev index handling
This fixes an issue getting resets index 1 and 3+, the spurius "> 0"
made it return the index 0 or 1, whatever index was passed.
The dm_test_reset_base() did not catch it, but the dm_test_reset_base() extension
catches it and this fixes the regression.
This also fixes a reggression on Amlogic G12A/G12B SoCs, where HDMI output was disable
even when Linux was booting.
Fixes: ea9dc35aab ("reset: Get the RESET by index without device") Reported-by: B1oHazard <ty3uk@mail.ua> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Makefile: fix generation of defaultenv.h from empty initial file
When CONFIG_USE_DEFAULT_ENV_FILE=y and the file
CONFIG_DEFAULT_ENV_FILE is empty (or at least doesn't contain any
non-comment, non-empty lines), we end up feeding nothing into xxd,
which in turn then outputs nothing. Then blindly appending ", 0x00"
means that we end up trying to compile (roughly)
const char defaultenv[] = { , 0x00 }
which is of course broken.
To fix that, change the frobbing of the text file so that we always
end up printing an extra empty line (which gets turned into that extra
nul byte we need) - that corresponds better to the binary format
consisting of a series of key=val nul terminated strings, terminated
by an empty string.
fs: btrfs: fix the false alert of decompression failure
There are some cases where decompressed sectors can have padding zeros.
In kernel code, we have lines to address such situation:
/*
* btrfs_getblock is doing a zero on the tail of the page too,
* but this will cover anything missing from the decompressed
* data.
*/
if (bytes < destlen)
memset(kaddr+bytes, 0, destlen-bytes);
kunmap_local(kaddr);
But not in U-boot code, thus we have some reports of U-boot failed to
read compressed files in btrfs.
Fix it by doing the same thing of the kernel, for both inline and
regular compressed extents.
Samuel Holland [Sat, 17 Apr 2021 14:34:37 +0000 (09:34 -0500)]
arm: zimage: Use correct symbol to hide messages in SPL
When zImage support was added to SPL, the messages were hidden to reduce
code size. However, the wrong config symbol was used. Since this file is
only built when CONFIG_SPL_FRAMEWORK=y, the messages were always hidden.
Use the correct symbol so the messages are printed in U-Boot proper.
Also use IS_ENABLED to drop the #ifdef.
Fixes: 431889d6ad9a ("spl: zImage support in Falcon mode") Signed-off-by: Samuel Holland <samuel@sholland.org>
When flush_cache() is called during boot on our ~7M kernel image, the
hundreds of thousands of WATCHDOG_RESET calls end up adding
significantly to boottime. Flushing a single cache line doesn't take
many microseconds, so doing these calls for every cache line is
complete overkill.
The generic watchdog_reset() provided by wdt-uclass.c actually
contains some rate-limiting logic that should in theory mitigate this,
but alas, that rate-limiting must be disabled on powerpc because of
its get_timer() implementation - get_timer() works just fine until
interrupts are disabled, but it just so happens that the "big"
flush_cache() call happens in the part of bootm where interrupts are
indeed disabled. [1] [2] [3]
I have checked with objdump that the generated code doesn't change
when this option is left at its default value of 0: gcc is smart
enough to see that the ">=" comparison is tautologically true, hence
all assignments to "flushed" are eliminated as dead stores.
On our board, setting the option to something like 65536 ends up
reducing total boottime by about 0.8 seconds.
allow opting out of WATCHDOG_RESET() from timer interrupt
Having WATCHDOG_RESET() called automatically from the timer interrupt
runs counter to the idea of a watchdog device - if the board runs into
an infinite loops with interrupts still enabled, the watchdog will
never fire.
When using CONFIG_(SPL_)WDT, the watchdog_reset function is a lot more
complicated than just poking a few SOC-specific registers - it
involves accessing all kinds of global data, and if the interrupt
happens at the wrong time (say, in the middle of an WATCHDOG_RESET()
call from ordinary code), that can end up corrupting said global data.
Allow the board to opt out of calling WATCHDOG_RESET() from the timer
interrupt handler by setting CONFIG_SYS_WATCHDOG_FREQ to 0 - as that
setting is currently nonsensical (it would be compile-time
divide-by-zero), it cannot affect any existing boards.
Add documentation for both the existing and extended meaning of
CONFIG_SYS_WATCHDOG_FREQ.
timer: mpc83xx_timer: fix build with CONFIG_{HW_, }WATCHDOG
The code, which is likely copied from arch/powerpc/lib/interrupts.c,
lacks a fallback definition of CONFIG_SYS_WATCHDOG_FREQ and refers to
a non-existing timestamp variable - obviously priv->timestamp is
meant.
Some boards don't work with the rate-limiting done in the generic
watchdog_reset() provided by wdt-uclass.
For example, on powerpc, get_timer() ceases working during bootm since
interrupts are disabled before the kernel image gets decompressed, and
when the decompression takes longer than the watchdog device
allows (or enough of the budget that the kernel doesn't get far enough
to assume responsibility for petting the watchdog), the result is a
non-booting board.
As a somewhat hacky workaround (because DT is supposed to describe
hardware), allow specifying hw_margin_ms=0 in device tree to
effectively disable the ratelimiting and actually ping the watchdog
every time watchdog_reset() is called. For that to work, the "has
enough time passed" check just needs to be tweaked a little to allow
the now==next_reset case as well.
Marek Vasut [Sat, 3 Apr 2021 23:10:15 +0000 (01:10 +0200)]
ARM: rmobile: Enable CONFIG_SYS_FLASH_PROTECTION
Enable CONFIG_SYS_FLASH_PROTECTION on Salvator-X(S), ULCB, Ebisu,
which means the Spansion HF PPB protection bits can be operated
using the 'protect' U-Boot command.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Sat, 25 Apr 2020 12:57:45 +0000 (14:57 +0200)]
clk: renesas: Only ever access documented bits in clock driver teardown
The clock driver used a heavy-handed approach where it turned off
all available clocks, while also possibly setting bits which are not
documented in the R-Car datasheet. Update the tables so that only
the bits which are documented are set or cleared when tearing down
the clock driver.
Note that the only clock left running before booting Linux are now
MFIC, INTC-AP, INTC-EX and SCIF2 / SCIF0 on V3x.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@konsulko.com>
Andre Przywara [Sat, 17 Apr 2021 21:55:19 +0000 (22:55 +0100)]
sunxi: DT: A64: Update devicetree files from Linux 5.12
Import updated devicetree files from the Linux v5.12 release.
Besides some node and audio port renames this changes the PHY modes to
either rgmii-id or rgmii-txid. From the board files the Pinephone sees
a lot of updates.
This also adds the long missing USB PHY property for controller 0, which
allows the U-Boot PHY driver to eventually use port 0 in host mode
(pending another U-Boot patch).
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Ivan Uvarov <i.uvarov@cognitivepilot.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Thu, 15 Apr 2021 23:53:17 +0000 (00:53 +0100)]
net: sun8i-emac: Fix pinmux setup for Allwinner H5
Commit eb5a2b671075 ("net: sun8i-emac: Determine pinmux based on SoC,
not EMAC type") switched the pinmux setup over to look at
CONFIG_MACH_SUN* symbols, to find the appropriate mux value.
Unfortunately this patch missed to check for the H5, which is
pin-compatible to the H3, but uses a different Kconfig symbol (because
it has ARMv8 vs. ARMv7 cores).
Replace the pure SUN8I_H3 symbol with the joint SUNXI_H3_H5 one, which is
there to cover the peripherals common to both SoCs.
Also explicitly list each supported SoC, and have an error message in the
fallback case, to avoid those problems in the future.
This fixes Ethernet support on all H5 boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Tested-by: Samuel Holland <samuel@sholland.org> # Orange Pi PC2 Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Aaron Williams [Wed, 7 Apr 2021 07:12:39 +0000 (09:12 +0200)]
mips: octeon: dts/dtsi: Change UART DT node to use clocks property
We already have a clock driver for MIPS Octeon. This patch changes the
Octeon DT nodes to supply the clock property via the clock driver
instead of using an hard-coded value, which is not correct in all cases.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Stefan Roese [Wed, 7 Apr 2021 07:12:36 +0000 (09:12 +0200)]
scsi: Add ata_swap_buf_le16() to support big-endian platforms
Otherwise the output will look like this on MIPS Octeon NIC23:
Device 0: (0:0) Vendor: ATA Prod.: aSDnsi klUrt aII Rev: 4X11
Type: Hard Disk
Capacity: 457862.8 MB = 447.1 GB (937703088 x 512)
instead of this version:
Device 0: (0:0) Vendor: TA Prod.: SanDisk Ultra II Rev: X411
Type: Hard Disk
Capacity: 457862.8 MB = 447.1 GB (937703088 x 512)
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Stefan Roese [Wed, 7 Apr 2021 07:12:35 +0000 (09:12 +0200)]
ata: ahci: Fix usage on big-endian platforms
This patch adds a few missing virt_to_phys() to use the correct physical
address for DMA operations in the common AHCI code. This is done to
support the big-endian MIPS Octeon platform.
Additionally the code a cleaned up a bit (remove some empty lines) and
made a bit better readable.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Stefan Roese [Wed, 7 Apr 2021 07:12:34 +0000 (09:12 +0200)]
sata: ahci_mvebu.c: Enable AHCI/SATA driver for MIPS Octeon
This patch enables the usage of the MVEBU AHCI/SATA driver. The only
changes necessary to support MIPS Octeon via DT based probing are, to
add the compatible DT property and the use of dev_remap_addr() so that
the correct mapped address is used in the Octeon case (phys != virt).
Please note that this driver supports the usage of the "scsi" command
and not the "sata" command, since it does not provide an own "scan"
function, which is needed for the "sata" cmd support.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Stefan Roese [Wed, 7 Apr 2021 07:12:33 +0000 (09:12 +0200)]
mips: octeon: cpu.c: Enable AHCI/SATA support
For easy AHCI/ SATA integration, this patch adds board_ahci_enable()
for the MVEBU AHCI driver, which will be used by this platform. This
platform specific "enable" function will setup the proper endian
swapping in the AHCI controller so that it can be used by the common
AHCI code.
Additionally the endian swizzle entry for AHCI in
octeon_should_swizzle_table[] is removed, as this enabled the original
lowlevel code function, e.g. octeon_configure_qlm(), for the QLM setup
to work correctly.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Stefan Roese [Wed, 7 Apr 2021 07:12:32 +0000 (09:12 +0200)]
mips: octeon: cpu.c: Add arch_misc_init() for pci-console & pci-bootcmd
This patch adds the necessary platform infrastructure code, so that the
MIPS Octeon drivers "serial_octeon_pcie_console" & "serial_bootcmd" can
be used. This is e.g. the bootmem initialization in a compatible way to
the Marvell 2013 U-Boot, so that the exisiting PC remote tools like
"oct-remote-console" & "oct-remote-load" can be used. This is be done in
the newly introduced arch_misc_init(), which calls the necessary init
functions when enabled.
These patches are in preparation for the MIPS Octeon NIC23 board
support, which is a desktop PCIe target board enabling these features.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Stefan Roese [Wed, 7 Apr 2021 07:12:31 +0000 (09:12 +0200)]
serial: serial_octeon_bootcmd.c: Add PCI remote console support
This patch adds the PCI bootcmd feature for MIPS Octeon, which will be
used by the upcoming Octeon III NIC23 board support. It enables the use
of the "oct-remote-load" and "oct-remote-bootcmd" on host PC's to
communicate with the PCIe target and load images into the onboard
memory and issue commands.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Stefan Roese [Wed, 7 Apr 2021 07:12:30 +0000 (09:12 +0200)]
serial: serial_octeon_pcie_console.c: Add PCI remote console support
This patch adds the PCI remote console feature for MIPS Octeon, which
will be used by the upcoming Octeon III NIC23 board support. It enables
the use of the "oct-remote-console" tool on host PC's to communicate
with the PCIe target.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Stefan Roese [Wed, 7 Apr 2021 07:12:29 +0000 (09:12 +0200)]
mips: octeon: cvmx-coremask.h: Fix cvmx_coremask_dprint() with DEBUG defined
As DEBUG is no Kconfig symbol, we can't use the IS_ENABLED() macros.
This patch switches to the unfortunately necessary #ifdef usage again
to make it work correctly.
Stefan Roese [Fri, 11 Dec 2020 16:06:12 +0000 (17:06 +0100)]
mips: octeon: octeon_ebb7304_defconfig: Enable Octeon PCIe and E1000
This patch changes the MIPS Octeon defconfig to enable some features
for PCIe enablement. This includes CONFIG_BOARD_LATE_INIT to call the
board specific serdes init code.
With these features enabled, the serdes and PCIe driver including the
Intel E1000 driver can be tested on the Octeon EBB7304.
projects / u-boot.git / log
