warp can run different kernel versions, such as NXP 4.1 or
mainline.
Currently the rootfs location is passed via mmcblk number and the
problem with this approach is that the mmcblk number for the eMMC
changes depending on the kernel version.
In order to avoid such issue, use UUID method to specify the rootfs
location.
Succesfully tested booting a NXP 4.1 and also a mainline 4.12 kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
embestmx6boards: Use PARTUUID to specify the rootfs location
Currently the rootfs location is passed via mmcblk number and the
problem with this approach is that the mmcblk number for the eMMC
changes depending on the kernel version.
In order to avoid such issue, use UUID method to specify the rootfs
location.
Also add CONFIG_BOOTCOMMAND to run finduuid function and distro_bootcmd.
mx6cuboxi: Use PARTUUID to specify the rootfs location
Currently the rootfs location is passed via mmcblk number and the
problem with this approach is that the mmcblk number for the eMMC
changes depending on the kernel version.
In order to avoid such issue, use UUID method to specify the rootfs
location.
wandboard: Use PARTUUID to specify the rootfs location
Currently the rootfs location is passed via mmcblk number and the
problem with this approach is that the mmcblk number for the eMMC
changes depending on the kernel version.
In order to avoid such issue, use UUID method to specify the rootfs
location.
mx6sabre: Use PARTUUID to specify the rootfs location
mx6sabre boards can run different kernel versions, such as NXP 4.1 or
mainline.
Currently the rootfs location is passed via mmcblk number and the
problem with this approach is that the mmcblk number for the eMMC
changes depending on the kernel version.
In order to avoid such issue, use UUID method to specify the rootfs
location.
Succesfully tested booting a NXP 4.1 and also a mainline kernel on a
mx6qsabresd and mx6dlsabreauto.
WEIM cannot be used when I2C3 is enabled due to pin conflict, so keep
WEIM disabled by default.
I2C3 controls GPIO I2C expander (USB host and OTG have VBUS controlled by
the GPIO I2C expander), magnetometer, accelerometer.
Not disabling WEIM in U-Boot causes I2C3 to behave badly when booting
a NXP 4.1 kernel, which leads to probe failure on several devices,
including the lack of USB:
Peng Fan [Mon, 12 Jun 2017 09:50:55 +0000 (17:50 +0800)]
mmc: fsl_esdhc: drop CONFIG_SYS_FSL_ESDHC_FORCE_VSELECT
CONFIG_SYS_FSL_ESDHC_FORCE_VSELECT is not the correct method
to set I/O to 1.8. To boards that does not support vqmmc-supply,
use vs18_enable in fsl_esdhc_cfg. If regulator is supported,
use fixed 1.8V regulator for vqmmc-supply.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: York Sun <york.sun@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
Peng Fan [Mon, 12 Jun 2017 09:50:54 +0000 (17:50 +0800)]
dm: mmc: fsl_esdhc: handle vqmmc supply
Handle vqmmc supply. Some boards have a fixed I/O voltage
at 1.8V for emmc, so the usdhc also needs to be configured
as 1.8V by setting VSELECT bit. The vs18_enable is the one
that used to checking whether setting VSELECT or not in
the driver. So if vqmmc supply is 1.8V, set vs18_enable,
the driver will set VSELECT.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: York Sun <york.sun@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Peng Fan [Mon, 12 Jun 2017 09:50:53 +0000 (17:50 +0800)]
mmc: fsl_esdhc: introduce vs18_enable for 1.8V fix I/O
When using eMMC with 1.8V I/O, the VSELECT bit need to be set in
the USDHC controller when init.
This patch adds a parameter "vs18_enable" in fsl_esdhc_cfg
structure and priv data, so each controller can have different
settings.
We could not use CONFIG_SYS_FSL_ESDHC_FORCE_VSELECT, it has problem
that it will apply to all USDHC controllers and it only set the 1.8V
at init phase. So if user does not select to the eMMC device,
the voltage on the I/O pins are not correct.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: York Sun <york.sun@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
Vanessa Maegima [Thu, 29 Jun 2017 12:33:46 +0000 (09:33 -0300)]
mx6sabreauto: Update to SPL only mode
As mx6sabreauto supports SPL now, all variants can boot using the same
defconfig.
This patch:
- Removes non-SPL targets.
- Renames target to mx6sabreauto_defconfig.
- Renames folder and board files to mx6sabreauto.
- Updates MAINTAINERS, Makefile and Kconfig accordingly.
- Removes .cfg files.
- Adds a README with instructions to build and flash SPL and u-boot.img.
Peter Robinson [Sat, 1 Jul 2017 17:44:03 +0000 (18:44 +0100)]
mx6cuboxi: Add support for sata
The Cubox-i and Hummingboard series of devices have an option of
SATA on board, and depending on how the fuses are blown even the
option to boot SPL from SATA. So enable support for it so it can
be used to boot the OS from if people desire.
mx7dsabresd: Set VLD04 output to 2.8V in PMIC initialization.
This change sets the VLDO4 settings output to 2.8V in PMIC
initialization so that the MIPI DSI/CSI input voltage is 2.8V
as per the schematics. The original code provides an output of
3.3V which violates the voltage mentioned in the schematics.
Lothar Waßmann [Tue, 27 Jun 2017 13:23:16 +0000 (15:23 +0200)]
net: fec_mxc: fix PHY initialization bug with CONFIG_DM_ETH
When CONFIG_DM_ETH is set, the FEC ethernet controller is reset after
the PHY has been set up and initialzed. This breaks the communication
with the PHY and results in an inoperable ethernet interface.
Do the initialization with CONFIG_DM_ETH in the same order as with
legacy ETH support to fix this.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Stefan Agner [Fri, 9 Jun 2017 20:13:12 +0000 (13:13 -0700)]
imx: mx6ull: fix USB bmode for i.MX 6UL and 6ULL
i.MX 6UL and 6ULL have different boot device capabilities and
use therefor use a different boot device selection table than
other i.MX 6 devices. Particularly, the value which has been
used so far (b0001) is assigned to QSPI boot for these two
devices.
There is no common reserved value for all i.MX 6devices. Use
b0010 for i.MX 6UL and 6ULL via compile time ifdef.
Masahiro Yamada [Thu, 22 Jun 2017 08:57:50 +0000 (17:57 +0900)]
dm: ofnode: use fdt32_t for DT property value to fix sparse warning
DTB is encoded in big endian. When we retrieve property values,
we need to use fdt32_to_cpu (aka be32_to_cpu) for endian conversion.
This is a bit error-prone, but sparse is useful to detect endian
mismatch.
We need to use (fdt32_t *) instead of (u32 *) for a pointer of a
property value. Otherwise sparse warns "cast to restricted __be32".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Thu, 22 Jun 2017 08:10:11 +0000 (17:10 +0900)]
dm: include <dm/util.h> from driver/core/dump.c
Include <dm/util.h> to fix sparse warnings:
symbol 'dm_dump_all' was not declared. Should it be static?
symbol 'dm_dump_uclass' was not declared. Should it be static?
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Thu, 22 Jun 2017 07:54:05 +0000 (16:54 +0900)]
dm: ofnode: rename ofnode_read_prop() to ofnode_get_property()
This function returns the pointer to the value of a node property.
The current name ofnode_read_prop() is confusing. Follow the naming
of_get_property() from Linux.
The return type (const u32 *) is wrong. DT property values can be
strings as well as integers. This is why of_get_property/fdt_getprop
returns an opaque pointer.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Simon Glass <sjg@chromium.org>
Tom Rini [Tue, 13 Jun 2017 11:10:35 +0000 (07:10 -0400)]
fdt: Check for NULL return from fdt_getprop in 'fdt set'
While the previous pass through fixed one place where we knew that
fdt_getprop would be given a positive len, in the case of 'fdt set' we
do not, so check that we did no get NULL from fdt_getprop().
Cc: Simon Glass <sjg@chromium.org> Reported-by: Coverity (CID: 163249)
Fixes 72c98ed1ab48 ("fdt: Add a check to do_fdt() for coverity") Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Mon, 12 Jun 2017 12:22:01 +0000 (06:22 -0600)]
tegra: fdt: Ensure that the console UART is enabled
Many tegra boards have the console UART node disabled. With livetree this
prevents serial from working since it does not 'force' the console to be
bound. Updates the affected boards to fix this error.
The boards were checked with:
for b in $(grep tegra boards.cfg |grep -v integrator | \
awk '{print $7}' | sort); do
echo $b;
fdtgrep -c nvidia,tegra20-uart b/$b/u-boot.dtb |grep okay;
done
Simon Glass [Mon, 12 Jun 2017 12:21:31 +0000 (06:21 -0600)]
dm: core: Add functions to obtain node's address/size cells
The of_n_addr_cells() and of_n_size_cells() functions are useful for
getting the size of addresses in a node, but in a few places U-Boot needs
to obtain the actual property value for a node without walking up the
stack. Add functions for this and just the existing code to use it.
Add a comment to the existing ofnode functions which do not do the right
thing with a flat tree.
Simon Glass [Mon, 12 Jun 2017 12:21:29 +0000 (06:21 -0600)]
dm: core: Add dev_read_resource() to read device resources
Add a function which reads resources from a device, such as the device
hardware address. This uses the "reg" property in the device.
Unlike other functions there is little sense in inlining this when
livetree is not being used because it has some logic in it and this would
just bloat the code size.
Simon Glass [Wed, 21 Jun 2017 03:28:49 +0000 (21:28 -0600)]
binman: Put our local modules ahead of system modules
If a system module is named the same as one of those used by binman we
currently pick the system module. Adjust the ordering so that our modules
are chosen instead.
The module conflict reported was 'tools' from jira-python. I cannot access
that package to test it.
Signed-off-by: Simon Glass <sjg@chromium.org> Reported-by: Kevin Hilman <khilman@baylibre.com> Acked-by: Kevin Hilman <khilman@baylibre.com>
Simon Glass [Mon, 19 Jun 2017 04:09:05 +0000 (22:09 -0600)]
sandbox: Stop printing platdata at the start of SPL
Currently we have code which prints out platform data at the start of SPL.
Now that we have tests for dtoc this is probably not necessary. Drop it.
Update test_ofplatdata to check for empty output since it is useful to
check that sandbox_spl works as expected.
Simon Glass [Mon, 19 Jun 2017 04:09:04 +0000 (22:09 -0600)]
dtoc: Add a comment about string replace in conv_name_to_c()
This function uses several separate string replaces where a regular
expression might seem more reasonable. Add a comment justifying the way it
is currently done.
Simon Glass [Mon, 19 Jun 2017 04:09:03 +0000 (22:09 -0600)]
dtoc: Move the main logic into the dtb_platdata file
Collect the main logic of dtoc into a function and put it into
dtb_platdata. This will allow tests to use this function instead of
duplicating the code themselves.
Simon Glass [Mon, 19 Jun 2017 04:09:01 +0000 (22:09 -0600)]
dtoc: Pass include_disabled explicitly
This option is the only one actually used by the dtb_platdata class. Pass
it explicitly to avoid needing to pass the whole option object to the
constructor.
Simon Glass [Mon, 19 Jun 2017 04:08:58 +0000 (22:08 -0600)]
dtoc: Split out the main class into its own file
To simplify running tests we should move this class into its own file.
This allows the tests to import it without having to import dtoc.py, which
runs the tests.
Simon Glass [Fri, 16 Jun 2017 03:39:33 +0000 (21:39 -0600)]
moveconfig: Allow automatic location and adding of 'imply'
By using a Kconfig parser we can find the location of each option in the
Kconfig tree. Using the information from the database we can then
automatically add an 'imply' option into the right place if requested by
the user.
Add a -a option to support adding 'imply' options. Display the location of
any existing 'imply' option so that progress can be examined. Add a -A
option to hide any existing 'imply' options so that already-completed
additions need not be considered further.
Simon Glass [Fri, 16 Jun 2017 03:39:32 +0000 (21:39 -0600)]
moveconfig: Allow control of which implying configs are shown
Sometimes it is useful to display CONFIG_TARGET or CONFIG_CMD configs. Add
an option to control this.
Also we generally ignore implying configs which affect fewer than 5
boards. But sometimes it is useful to show those those, so add an option
that reduces the minimum to two.
ERRATUM configs are never useful for implying things, so ignore those.
Simon Glass [Fri, 16 Jun 2017 03:39:31 +0000 (21:39 -0600)]
moveconfig: Allow piping in 'git show --stat' output
It is useful to be able to process only a subset of boards to save time.
Often that subset is defined by the defconfig files in a git commit. This
change allows things like:
# Build the database
./tools.moveconfig.py -b
# Find some implying configs
./tools/moveconfig.py -i CONFIG_X
# Add some 'imply' statements to Kconfig files
./tools/moveconfig.py -i CONFIG_X -a CONFIG_A,CONFIG_B
# Reprocess the defconfig files to see if we can drop some changes
git show --stat | ./tools/moveconfig.py -s -d -
# Update the commit, with fewer defconfig changes
gii commit -au
Where the commit contains defconfig files, this will reprocess them to
take account of the imply statements that you added.
Simon Glass [Fri, 16 Jun 2017 03:37:53 +0000 (21:37 -0600)]
sandbox: Enable more console options
Enable the pre-console buffer, displaying the model and post-relocation
console announce on sandbox. Also add a model name to the device tree.
This allows testing of these features.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Stephen Warren <swarren@nvidia.com>
Simon Glass [Fri, 16 Jun 2017 03:37:52 +0000 (21:37 -0600)]
console: Use map_sysmem() for the pre-relocation console
At present this feature casts the address to a pointer. Use the
map_sysmem() function so that it will work correctly on sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Stephen Warren <swarren@nvidia.com>
Simon Glass [Fri, 16 Jun 2017 03:37:50 +0000 (21:37 -0600)]
Allow displaying the U-Boot banner on a video display
At present the U-Boot banner is only displayed on the serial console. If
this is not visible to the user, the banner does not show. Some devices
have a video display which can usefully display this information.
Add a banner which is printed after relocation only on non-serial devices
if CONFIG_DISPLAY_BOARDINFO_LATE is defined.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Stephen Warren <swarren@nvidia.com>
Simon Glass [Fri, 16 Jun 2017 18:51:42 +0000 (12:51 -0600)]
display_options: Refactor to allow obtaining the banner
Move the display options code into a separate function so that the U-Boot
banner can be obtained from other code. Adjust the 'version' command to
use it.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Stephen Warren <swarren@nvidia.com>
Simon Glass [Thu, 15 Jun 2017 03:28:46 +0000 (21:28 -0600)]
dm: ahci: Add a driver for SCSI on AHCI
Some AHCI drivers use SCSI under the hood. Rather than making the AHCI
driver be in the SCSI uclass it makes sense to have the AHCI device create
a SCSI device as a child. That way we can handle any AHCI-specific
operations rather than trying to pretend tha the device is just SCSI.
To handle this we need to provide a way for AHCI drivers to bind a SCSI
device as its child, and probe it. Add functions for this.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Thu, 15 Jun 2017 03:28:43 +0000 (21:28 -0600)]
dm: scsi: Add operations for SCSI devices
The SCSI uclass currently has no operations. It just uses the global SCSI
functions. Fix this by adding operations to the only two drivers that use
the uclass, and replacing the global functions with those defined locally
in the SCSI code.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Thu, 15 Jun 2017 03:28:42 +0000 (21:28 -0600)]
dm: ahci: Create a local version of two SCSI functions
With driver model we need to define implementations of exec() and
bus_reset() separately for each SCSI driver. As a first step, create a
local version of each function in the AHCI driver and call each from its
global version.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Thu, 15 Jun 2017 03:28:41 +0000 (21:28 -0600)]
dm: scsi: Document and rename the scsi_scan() parameter
The 'mode' parameter is actually a flag to determine whether to display
a list of devices found during the scan. Rename it to reflect this, add a
function comment and adjust callers to use a boolean.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Thu, 15 Jun 2017 03:28:40 +0000 (21:28 -0600)]
dm: scsi: Add a device pointer to scan_exec(), scsi_bus_reset()
With driver model these functions need a device pointer. Add one even
when CONFIG_DM_SCSI is not defined. This avoids having ugly conditional
function prototypes, When CONFIG_DM_SCSI is not defined we can just ignore
the pointer.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Thu, 15 Jun 2017 03:28:38 +0000 (21:28 -0600)]
dm: ahci: Drop use of probe_ent
With driver model we cannot have static data or assume that there is only
one device of each time. Adjust the code so that 'probe_ent' is not needed
with driver model. Add a new ahci_init_dm() function which can init AHCI
for driver model without re-allocating the uclass data. Move over the only
existing driver to use this new function.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Thu, 15 Jun 2017 03:28:37 +0000 (21:28 -0600)]
dm: ahci: Unwind the confusing init code
Two AHCI drivers use SCSI with CONFIG_DM_SCSI. The SCSI uclass calls
scsi_low_level_init() which is implemented by ahci.c. If
CONFIG_SCSI_AHCI_PLAT is defined it does one thing and if it is not
it does something else.
We don't need to call through scsi_low_level_init() to get the init
completed. Instead, adjust the two drivers to call into AHCI directly.
Drop the post-probe init in the SCSI uclass. This means that driver model
doesn't need to use scsi_low_level_init(). It is a legacy function and
driver model should use a driver's probe() method instead.
While we are here, add a comment to the top of the file explaining what
ahci.c does.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
projects / u-boot.git / log
