cfi_flash: Fix detection of 8-bit bus flash devices via address shift
We had a problem detecting 8/16bit flash devices connected only via
8bits to the SoC for quite a while. Commit 239cb9d9
[mtd: cfi_flash: Fix CFI flash driver for 8-bit bus support] finally
fixed this 8-bit bus support. But also broke some other boards using
this cfi driver. So this patch had to be reverted.
I spotted a different, simpler approach for this 8-bit bus support
on the barebox mailing list posted by
Oleksij Rempel <bug-track@fisher-privat.net>:
"
Many cfi chips support 16 and 8 bit modes. Most important
difference is use of so called "Q15/A-1" pin. In 16bit mode this
pin is used for data IO. In 8bit mode, it is an address input
which add one more least significant bit (LSB). In this case
we should shift all adresses by one:
For example 0xaa << 1 = 0x154
"
This patch now is a port of this barebox patch to U-Boot.
Along with the change w.r.t from barebox,
Some flash chips can support multiple bus widths, override the
interface width and limit it to the port width.
Tested on 16-bit Spansion flash on sequoia.
Tested 8-bit flashes like 256M29EW, 512M29EW.
Signed-off-by: Stefan Roese <sr@denx.de> Tested-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Cc: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Andre Przywara <andre.przywara@arm.com> Cc: Vignesh Raghavendra <vigneshr@ti.com> Cc: Simon Glass <sjg@chromium.org> Cc: Mario Six <mario.six@gdsys.cc> Cc: York Sun <york.sun@nxp.com> Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Simon Glass [Wed, 24 Mar 2021 21:44:33 +0000 (10:44 +1300)]
test: Allow tests to run on any board
Due to a recent change, tests are limited to running on sandbox only.
Correct this so that any architecture can run them.
Signed-off-by: Simon Glass <sjg@chromium.org> Reported-by: Sean Anderson <seanga2@gmail.com> Fixes: c79705ea938 ("test: Move dm_test_init() into test-main.c") Tested-by: Sean Anderson <seanga2@gmail.com>
./include/os.h:139: warning:
Function parameter or member 'ptr' not described in 'os_realloc'
./include/os.h:139: warning:
Function parameter or member 'length' not described in 'os_realloc'
Fixes: 14e46dfb176b ("sandbox: Add os_realloc()") Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 26 Mar 2021 03:17:28 +0000 (16:17 +1300)]
log: Fix up debug_cond() when LOG is enabled
At present debug() statements can cause debuf output to appear when LOG is
enabled but DEBUG is not. This is not intended and it seems that the
condition is wrong.
Simon Glass [Fri, 26 Mar 2021 03:17:27 +0000 (16:17 +1300)]
dtoc: Improve handling of reg properties
This existing code assumes that a reg property is larger than one cell,
but this is not always the case. Fix this assumption.
Also if a node's parent is missing the #address-cells and #size-cells
properties we use 2 as a default for each. But this should not happen in
practice. More likely the properties were removed for SPL due to there
being no 'u-boot,dm-pre-reloc' property, or similar. Add a warning for
this as the failure can be very confusing.
Simon Glass [Fri, 26 Mar 2021 03:17:26 +0000 (16:17 +1300)]
dtoc: Adjust detection of 64-bit properties
At present an empty size is considered to be a 64-bit value. This does not
seem useful and wastes space. Limit the 64-bit detection to where one or
both of the addr/size is two cells or more.
Simon Glass [Fri, 26 Mar 2021 01:39:39 +0000 (14:39 +1300)]
buildman: Add an encoding to the out-env file
The environment may contain some unicode characters. At least that is what
seemed to happen on one commit:
Building current source for 1 boards (0 threads, 64 jobs per thread)
0 0 0 /1 -1 (starting)
Traceback (most recent call last):
File ".../tools/buildman/buildman", line 64, in <module>
ret_code = control.DoBuildman(options, args)
File "tools/buildman/control.py", line 372, in DoBuildman
options.keep_outputs, options.verbose)
File ".../tools/buildman/builder.py", line 1704, in BuildBoards
results = self._single_builder.RunJob(job)
File ".../tools/buildman/builderthread.py", line 526, in RunJob
self._WriteResult(result, job.keep_outputs, job.work_in_output)
File ".../tools//buildman/builderthread.py", line 349, in _WriteResult
print('%s="%s"' % (var, env[var]), file=fd)
UnicodeEncodeError: 'ascii' codec can't encode characters in position
311-312: ordinal not in range(128)
The problem defies repetition with any change at all to buildman. But
let's set an encoding in any case.
Simon Glass [Wed, 24 Mar 2021 21:26:09 +0000 (10:26 +1300)]
clk: Return -ENOSYS when system call is not available
Update clk_composite_set_parent() to use -ENOSYS, which is the correct
error code for U-Boot. Also rearrange the code so that the error condition
is clearly indicated and the function runs to the end in the normal case,
since this is the common style in U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Sean Anderson <seanga2@gmail.com>
Simon Glass [Wed, 24 Mar 2021 21:26:08 +0000 (10:26 +1300)]
clk: Update drivers to use -EINVAL
At present some drivers use -ENOSUPP to indicate that an unknown or
unsupported clock is used. Most use -EINVAL, indicating an invalid value,
so convert everything to that.
Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de>
Simon Glass [Wed, 24 Mar 2021 21:26:03 +0000 (10:26 +1300)]
dm: core: Document the common error codes
Driver model uses quite strong conventions on error codes, but these are
currently not clearly documented. Add a description of the commonly used
errors.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Sean Anderson <seanga2@gmail.com>
Tom Rini [Sun, 4 Apr 2021 20:04:56 +0000 (16:04 -0400)]
sphinx: Pin to docutils-0.16
In newer docutils writers/latex2e/docutils.sty has a unicode character
in the comments which can in turn cause Python 3.6 at least to fail.
Pin to the previous docutils release for now.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Tom Rini <trini@konsulko.com>
Simon Glass [Wed, 31 Mar 2021 22:18:13 +0000 (11:18 +1300)]
Makefile: Silence the deprecation script
This bash code is currently showing up in the build unless 'make -s' is
used. We don't normally show these sorts of things as they are confusing.
Also this code was not shown before the recent refactoring of how these
messages are displayed.
Add an '@' to silence it.
Suggested-by: Tom Rini <trini@konsulko.com> Signed-off-by: Simon Glass <sjg@chromium.org> Reported-by: Bin Meng <bmeng.cn@gmail.com> Fixes: 13732528516 ("Makefile: Add common code to report deprecation")
Andy Shevchenko [Thu, 11 Feb 2021 14:40:12 +0000 (16:40 +0200)]
test: Don't unmount not (yet) mounted system
When test suite tries to create a file for a new filesystem test case and fails,
the clean up of the exception tries to unmount the image, that has not yet been
mounted. When it happens, the fuse_mounted global variable is set to False and
inconveniently the test case tries to use sudo, so without this change the
admin of the machine gets an (annoying) email:
Subject: *** SECURITY information for example.com ***
example.com : Feb 5 19:43:47 : ... COMMAND=/bin/umount .../build-sandbox/persistent-data/mnt
and second run of the test cases on uncleaned build folder will ask for sudo
which is not what expected.
Besides that there is a double unmount calls during successfully run test case.
All of these due to over engineered Python try-except clause and people didn't
get it properly at all. The rule of thumb is that don't use more keywords than
try-except in the exception handling code. Nevertheless, here we adjust code
to be less intrusive to the initial logic behind that complex and unclear
constructions in the test case, although it adds a lot of lines of the code,
i.e. splits one exception handler to three, so on each step we know what
cleanup shall perform.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Andre Przywara [Thu, 25 Mar 2021 16:20:13 +0000 (16:20 +0000)]
sunxi: H616: Change TF-A load address to beginning of DRAM
Loading Trusted-Firmware's BL31 at 16KB into DRAM was originally a hack
to allow sharing more code with the other SoCs (which use this offset
in SRAM). However there is no longer a reason for that, as the
problematic macros have been properly separated there.
The latest (and hopefully final) TF-A code drop now changes the load
address to the beginning of DRAM, which is also more easily protected
by the Trustzone memory controller (code to be done).
Adjust the load address of BL31 now, to avoid any issues with
incompatible versions later on (the TF-A patches are about to be merged).
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Samuel Holland <samuel@sholland.org>
Tom Rini [Tue, 30 Mar 2021 15:24:09 +0000 (11:24 -0400)]
Merge tag 'u-boot-atmel-2021.07-a' of https://source.denx.de/u-boot/custodians/u-boot-atmel into next
First set of u-boot-atmel features for 2021.07 cycle:
This small feature set includes the implementation of the slew rate for
the PIO4 pin controller device, and a fix for arm926ejs-based
microprocessors that avoids a crash.
Michal Simek [Thu, 26 Nov 2020 13:25:02 +0000 (14:25 +0100)]
xilinx: Sync DTs with Linux kernel
There are several changes which happen in mainline kernel which should get
also to U-Boot. Here is the list of patches from the kernel:
- ARM: zynq: Fix leds subnode name for zc702/zybo-z7
- arm64: dts: zynqmp: Fix leds subnode name for zcu100/ultra96 v1
- arm64: dts: zynqmp: Fix u48 si5382 chip on zcu111
- arm64: dts: zynqmp: Wire up the DisplayPort subsystem
- arm64: dts: zynqmp: Add DisplayPort subsystem
- arm64: dts: zynqmp: Add DPDMA node
- arm64: dts: zynqmp: Enable phy driver for Sata on zcu102/zcu104/zcu106
- arm64: dts: zynqmp: Enable si5341 driver for zcu102/106/111
- arm64: dts: zynqmp: Add DT description for si5328 for zcu102/zcu106
- arm64: dts: zynqmp-zcu100-revC: correct interrupt flags
- arm64: dts: xilinx: align GPIO hog names with dtschema
- arm64: zynqmp: Add Xilinx AES node
- dt: bindings: dma: xilinx: dpdma: DT bindings for Xilinx DPDMA
but also some other changes have been done.
- Using only one compatible string for adxl345 on zturn
- Remove Xilinx internal DP bindings
- Remove USB3.0 serdes configurations
- Remove SATA serdes configuration for zc1232
- Resort nvmem_firmware
- Update nand compatible string
- Aling power-domains property for sd0/1
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
arm64: zynqmp: Rename clocks as per the Arasan NAND driver
In zynqmp.dtsi file renamed "clk_sys" clock to "controller" and
"clk_flash" clock to "bus" as per upstreamed Arasan NAND driver.
This fixes NAND driver probe failure.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
EMMC will have bus-width 8 and it is non-removable in general. These
are missing from dt node. Add bus-width and non-removable parameters
to emmc node.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Xiaobo Tian [Sat, 27 Feb 2021 14:39:11 +0000 (22:39 +0800)]
arm64: rk3399: Add support NanoPi R4s
NanoPi R4s is SBC base on Rockchip RK3399 hexa-core processor with
dual-Core Cortex-A72 and Mali-T864 GPU with 4GiB(LPDDR4) of RAM, SD card support,
including 2 gigabit ethernet(RTL8211E 1Gbps - RTL8111H 1Gbps) and 2 USB 3.0 port.
port.It also has two GPIO headers which allows further peripherals to be used.
The devicetree file is taken of the rk3399 nanopi4 Linux kernel [1].
Roger Pau Monné [Mon, 22 Feb 2021 09:25:58 +0000 (10:25 +0100)]
odroid-go2: do not disable EFI
Remove the unset of the EFI loader, it's possible for U-Boot to
provide a EFI environment on this board, and it's also required by
the FreeBSD loader which mandated EFI on Aarch64.
Signed-off-by: Roger Pau Monné <royger@FreeBSD.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
rockchip: rk3399-puma: Increase environment size to 16 kiB.
On Puma we have the environment at an offset of 16 kiB.
On the eMMC this gives us 16 kiB for the environment before the SPL starts.
On the SPI NOR we also have 16 kiB until end of flash.
So let's increase the environment size from 8 kiB to its maximum
of 16 kiB for both MMC and SPI NOR.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com> Reviewed-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
A commit from last year re-imported the DTS files form the upstream kernel.
By doing so the VDD_LOG regulator in the board's DTS was dropped.
Let's restore this, but move it into the u-boot overlay to prevent this
issue in the future.
Fixes: 167efc2c7a46 ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux") Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com> Reviewed-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Rock960 doesn't have SPI flash on-board, but the bits
get enabled by default which means when booting we get
some errors. Explicitly disable it to stop the errors.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Heiko Stuebner [Tue, 9 Feb 2021 13:47:08 +0000 (14:47 +0100)]
rockchip: rk3368: sync main rk3368 dtsi from Linux
This is the state as of v5.10 + the recently added timer0 phandle
targetted at the 5.12 merge window.
With this the non-mainline nodes like the dmc move to a separate
rk3368-u-boot.dtsi that is included from the board-specific
-u-boot.dtsi files, similar to how rk3399 does this.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Heiko Stuebner [Tue, 9 Feb 2021 13:47:06 +0000 (14:47 +0100)]
rockchip: rk3368: move STACK_R_ADDR address and into Kconfig
With the STACK_R_ADDR at 0x600000 (6MB) we're competing with
with the loading address of either u-boot or atf parts, so move
that away to 0x4000000 (64MB) similar to rk3399.
Only lion currently sets that at all but not sheep the second
rk3368 board, so just move that to the Kconfig for rk3368 similar
to rk3399 as well.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Heiko Stuebner [Tue, 9 Feb 2021 13:47:03 +0000 (14:47 +0100)]
rockchip: rk3368: adjust CONFIG_SYS_LOAD_ADDR
CONFIG_SYS_LOAD_ADDR currently is at 0x00280000 which is only 512KB
behind the area where we load u-boot to, which depending on u-boot size
may overlap at some point.
So for safety just pick the same value rk3399 has and set
CONFIG_SYS_LOAD_ADDR to 0x00800800 on rk3368 as well.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Using a non-default SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR setting makes the
resulting u-boot-rockchip.bin unbootable, as it gets stuck after SPL.
Removing the setting from the defconfig allows U-Boot to load
successfully.
Signed-off-by: Roger Pau Monné <royger@FreeBSD.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Robert Hancock [Thu, 11 Mar 2021 22:55:50 +0000 (16:55 -0600)]
net: gem: Fix setting PCS auto-negotiation state
The code was trying to disable PCS auto-negotiation when a fixed-link node
is present and enable it otherwise. However, the PCS registers were being
written before the PCSSEL bit was set in the network configuration
register, and it appears that in this state, PCS register writes are
ignored. The result is that the intended change only took effect on the
second network operation that was performed, since at that time PCSSEL is
already enabled.
Fix the order of register writes so that PCS registers are only written to
after the PCS is enabled.
Fixes: 26e62cc971 ("net: gem: Disable PCS autonegotiation in case of fixed-link") Signed-off-by: Robert Hancock <robert.hancock@calian.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Jessica Clarke [Sat, 20 Mar 2021 20:43:05 +0000 (20:43 +0000)]
Support building on macOS/arm64
On Arm-based Macs, -no_pie is ignored and gives a linker warning.
Moreover, the build falls over with:
ld: Absolute addressing not allowed in arm64 code but used in '_image_type_ptr_aisimage' referencing '_image_type_aisimage'
for dumpimage and mkimage, since we put data structs in text sections
not data sections and so cannot have dynamic relocations. Instead, move
the sections to __DATA and drop disabling PIE.
Signed-off-by: Jessica Clarke <jrtc27@jrtc27.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Sean Anderson [Fri, 26 Mar 2021 02:02:28 +0000 (22:02 -0400)]
dm: test: Always include command.h for print_ut
We need this header for U_BOOT_CMD, which is always present even without
EFI.
Fixes: 82c468a049 ("dm: test: Update Makefile conditions") Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 27 Mar 2021 17:53:08 +0000 (06:53 +1300)]
test: Add udevice declaration to avoid build error
When including this file on a board other than sandbox (e.g by enabling
UNIT_TEST and CMD_SETEXPR) an results. Fix it by declaring struct udevice
first.
Signed-off-by: Simon Glass <sjg@chromium.org> Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tom Rini [Sat, 27 Mar 2021 15:58:37 +0000 (11:58 -0400)]
Merge branch '2021-03-27-master-imports'
- Rework the deprecation warnings to be consistently phrased.
- Add in a warning for DM_I2C, for a year from next release.
- Fix Azure builds of Windows host tools.
Tom Rini [Fri, 26 Mar 2021 19:14:14 +0000 (15:14 -0400)]
Azure: Use "pacman -Sy" to install the toolchain
We now see an error such as:
warning: database file for 'ucrt64' does not exist (use '-Sy' to download)
error: failed to prepare transaction (could not find database)
So use -Sy as suggested.
Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Thu, 25 Mar 2021 08:24:42 +0000 (21:24 +1300)]
Makefile: Use common code for DM_ETH deprecation warning
Update the CONFIG_DM_ETH check to use the 'deprecated' function.
Tested with snow
Old message:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
New message:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Simon Glass [Thu, 25 Mar 2021 08:24:41 +0000 (21:24 +1300)]
Makefile: Use common code for WDT deprecation warning
Update the CONFIG_WDT check to use the 'deprecated' function.
Tested with kmcent2
Old message:
===================== WARNING ======================
This board does not use CONFIG_WDT (DM watchdog support).
Please update the board to use CONFIG_WDT before the
v2019.10 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
New message:
===================== WARNING ======================
This board does not use CONFIG_WDT (Driver Model
for DM watchdog). Please update the board to use
CONFIG_WDT before the v2019.10 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Simon Glass [Thu, 25 Mar 2021 08:24:40 +0000 (21:24 +1300)]
Makefile: Use common code for SPI_FLASH deprecation warning
Update the CONFIG_DM_SPI_FLASH check to use the 'deprecated' function.
Tested with vinco
Old message:
===================== WARNING ======================
This board does not use CONFIG_DM_SPI_FLASH. Please update
the board to use CONFIG_SPI_FLASH before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
New message:
===================== WARNING ======================
This board does not use CONFIG_DM_SPI_FLASH (Driver Model
for SPI flash). Please update the board to use
CONFIG_DM_SPI_FLASH before the v2019.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Simon Glass [Thu, 25 Mar 2021 08:24:39 +0000 (21:24 +1300)]
Makefile: Use common code for DM_VIDEO deprecation warning
Update the CONFIG_DM_VIDEO check to use the 'deprecated' function.
Tested with pxm2
Old message:
===================== WARNING ======================
This board does not use CONFIG_DM_VIDEO Please update
the board to use CONFIG_DM_VIDEO before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
New message:
===================== WARNING ======================
This board does not use CONFIG_DM_VIDEO (Driver Model
for video). Please update the board to use
CONFIG_DM_VIDEO before the v2019.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
==================================================
Simon Glass [Thu, 25 Mar 2021 08:24:38 +0000 (21:24 +1300)]
Makefile: Use common code for PCI deprecation warning
Update the CONFIG_DM_PCI check to use the 'deprecated' function.
Tested with MPC8349ITX
Old message:
===================== WARNING ======================
This board does not use CONFIG_DM_PCI Please update
the board to use CONFIG_DM_PCI before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
New message:
===================== WARNING ======================
This board does not use CONFIG_DM_PCI (Driver Model
for PCI). Please update the board to use
CONFIG_DM_PCI before the v2019.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Simon Glass [Thu, 25 Mar 2021 08:24:37 +0000 (21:24 +1300)]
Makefile: Use common code for LIBATA deprecation warning
Update the CONFIG_LIBATA check to use the 'deprecated' function.
Tested with MPC8349ITX
Old message:
===================== WARNING ======================
This board does use CONFIG_LIBATA but has CONFIG_AHCI not
enabled. Please update the storage controller driver to use
CONFIG_AHCI before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
New message:
===================== WARNING ======================
This board does not use CONFIG_AHCI (Driver Model
for AHCI). Please update the board to use
CONFIG_AHCI before the v2019.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Simon Glass [Thu, 25 Mar 2021 08:24:36 +0000 (21:24 +1300)]
Makefile: Use common code for MVSATA_IDE deprecation warning
Update the CONFIG_MVSATA_IDE check to use the 'deprecated' function.
Tested with nas220
Old message:
===================== WARNING ======================
This board does use CONFIG_MVSATA_IDE which is not
ported to driver-model (DM) yet. Please update the storage
controller driver to use CONFIG_AHCI before the v2019.07
release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
New message:
===================== WARNING ======================
This board does not use CONFIG_AHCI (Driver Model
for AHCI instead of CONFIG_MVSATA_IDE). Please update the board to use
CONFIG_AHCI before the v2019.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Simon Glass [Thu, 25 Mar 2021 08:24:35 +0000 (21:24 +1300)]
Makefile: Use common code for USB deprecation warning
Update the USB check to use the 'deprecated' function.
Tested with xpress
Old message:
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
New message:
===================== WARNING ======================
This board does not use CONFIG_DM_USB (Driver Model
for USB). Please update the board to use
CONFIG_DM_USB before the v2019.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Simon Glass [Thu, 25 Mar 2021 08:24:34 +0000 (21:24 +1300)]
Makefile: Use common code for MMC deprecation warning
Update the MMC check to use the 'deprecated' function.
Tested with zc5202
Old message:
===================== WARNING ======================
This board does not use CONFIG_DM_MMC. Please update
the board to use CONFIG_DM_MMC before the v2019.04 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
New message:
===================== WARNING ======================
This board does not use CONFIG_DM_MMC (Driver Model
for MMC). Please update the board to use
CONFIG_DM_MMC before the v2019.04 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Simon Glass [Thu, 25 Mar 2021 08:24:33 +0000 (21:24 +1300)]
Makefile: Add common code to report deprecation
Add a function which can be called to report a migration problem. This
will make it easier to add new migration checks, since the logic and
strings are not spread out over 8 lines of code.
Simon Glass [Sun, 21 Mar 2021 05:24:38 +0000 (18:24 +1300)]
dtoc: Support adding subnodes alongside existing ones
So far we have only needed to add subnodes to empty notds, so have not
had to deal with ordering. However this feature is needed for binman's
expanded nodes, since there may be another node in the same section.
While libfdt adds new properties after existing properties, it adds new
subnodes before existing subnodes. This means that we must reorder the
nodes in the cached version, so that the ordering remains consistent.
Update the sync implementation to sync existing subnodes first, then
add new ones, then tidy up the ordering in the cached version. Update the
test to cover this behaviour.
Also improve the comment about property syncing while we are here.
Simon Glass [Sun, 21 Mar 2021 05:24:37 +0000 (18:24 +1300)]
dtoc: Add a subnode test for multiple nodes
Add a new test that adds a subnode alongside an existing one, as well as
adding properties to a subnode. This will expand to adding multiple
subnodes in future patches. Put a node after the one we are adding to so
we can check that things sync correctly.
The testAddNode() test should be in the TestNode class since it is a node
test, so move it.
Simon Glass [Sun, 21 Mar 2021 05:24:36 +0000 (18:24 +1300)]
dtoc: Tweak ordering of fdt-offsets refreshing
Once the tree has been synced, thus potentially moving things around in the
fdt, we set _cached_offsets to False so that a refresh will happen next
time a property is accessed.
This 'lazy' refresh doesn't really save much time, since refresh is a very
fast operation, just a single walk of the tree. Also, having the refresh
happen in the bowels of property access it makes it harder to figure out
what is going on.
Simplify the code by always doing a refresh before and after a sync. Set
_cached_offsets to True immediately after this, in the Refresh() function,
since this makes more sense than doing it in the caller.
projects / u-boot.git / log
