Aaron Williams [Wed, 7 Apr 2021 07:12:39 +0000 (09:12 +0200)]
mips: octeon: dts/dtsi: Change UART DT node to use clocks property
We already have a clock driver for MIPS Octeon. This patch changes the
Octeon DT nodes to supply the clock property via the clock driver
instead of using an hard-coded value, which is not correct in all cases.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Stefan Roese [Wed, 7 Apr 2021 07:12:36 +0000 (09:12 +0200)]
scsi: Add ata_swap_buf_le16() to support big-endian platforms
Otherwise the output will look like this on MIPS Octeon NIC23:
Device 0: (0:0) Vendor: ATA Prod.: aSDnsi klUrt aII Rev: 4X11
Type: Hard Disk
Capacity: 457862.8 MB = 447.1 GB (937703088 x 512)
instead of this version:
Device 0: (0:0) Vendor: TA Prod.: SanDisk Ultra II Rev: X411
Type: Hard Disk
Capacity: 457862.8 MB = 447.1 GB (937703088 x 512)
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Stefan Roese [Wed, 7 Apr 2021 07:12:35 +0000 (09:12 +0200)]
ata: ahci: Fix usage on big-endian platforms
This patch adds a few missing virt_to_phys() to use the correct physical
address for DMA operations in the common AHCI code. This is done to
support the big-endian MIPS Octeon platform.
Additionally the code a cleaned up a bit (remove some empty lines) and
made a bit better readable.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Stefan Roese [Wed, 7 Apr 2021 07:12:34 +0000 (09:12 +0200)]
sata: ahci_mvebu.c: Enable AHCI/SATA driver for MIPS Octeon
This patch enables the usage of the MVEBU AHCI/SATA driver. The only
changes necessary to support MIPS Octeon via DT based probing are, to
add the compatible DT property and the use of dev_remap_addr() so that
the correct mapped address is used in the Octeon case (phys != virt).
Please note that this driver supports the usage of the "scsi" command
and not the "sata" command, since it does not provide an own "scan"
function, which is needed for the "sata" cmd support.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Stefan Roese [Wed, 7 Apr 2021 07:12:33 +0000 (09:12 +0200)]
mips: octeon: cpu.c: Enable AHCI/SATA support
For easy AHCI/ SATA integration, this patch adds board_ahci_enable()
for the MVEBU AHCI driver, which will be used by this platform. This
platform specific "enable" function will setup the proper endian
swapping in the AHCI controller so that it can be used by the common
AHCI code.
Additionally the endian swizzle entry for AHCI in
octeon_should_swizzle_table[] is removed, as this enabled the original
lowlevel code function, e.g. octeon_configure_qlm(), for the QLM setup
to work correctly.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Stefan Roese [Wed, 7 Apr 2021 07:12:32 +0000 (09:12 +0200)]
mips: octeon: cpu.c: Add arch_misc_init() for pci-console & pci-bootcmd
This patch adds the necessary platform infrastructure code, so that the
MIPS Octeon drivers "serial_octeon_pcie_console" & "serial_bootcmd" can
be used. This is e.g. the bootmem initialization in a compatible way to
the Marvell 2013 U-Boot, so that the exisiting PC remote tools like
"oct-remote-console" & "oct-remote-load" can be used. This is be done in
the newly introduced arch_misc_init(), which calls the necessary init
functions when enabled.
These patches are in preparation for the MIPS Octeon NIC23 board
support, which is a desktop PCIe target board enabling these features.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Stefan Roese [Wed, 7 Apr 2021 07:12:31 +0000 (09:12 +0200)]
serial: serial_octeon_bootcmd.c: Add PCI remote console support
This patch adds the PCI bootcmd feature for MIPS Octeon, which will be
used by the upcoming Octeon III NIC23 board support. It enables the use
of the "oct-remote-load" and "oct-remote-bootcmd" on host PC's to
communicate with the PCIe target and load images into the onboard
memory and issue commands.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Stefan Roese [Wed, 7 Apr 2021 07:12:30 +0000 (09:12 +0200)]
serial: serial_octeon_pcie_console.c: Add PCI remote console support
This patch adds the PCI remote console feature for MIPS Octeon, which
will be used by the upcoming Octeon III NIC23 board support. It enables
the use of the "oct-remote-console" tool on host PC's to communicate
with the PCIe target.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Stefan Roese [Wed, 7 Apr 2021 07:12:29 +0000 (09:12 +0200)]
mips: octeon: cvmx-coremask.h: Fix cvmx_coremask_dprint() with DEBUG defined
As DEBUG is no Kconfig symbol, we can't use the IS_ENABLED() macros.
This patch switches to the unfortunately necessary #ifdef usage again
to make it work correctly.
Stefan Roese [Fri, 11 Dec 2020 16:06:12 +0000 (17:06 +0100)]
mips: octeon: octeon_ebb7304_defconfig: Enable Octeon PCIe and E1000
This patch changes the MIPS Octeon defconfig to enable some features
for PCIe enablement. This includes CONFIG_BOARD_LATE_INIT to call the
board specific serdes init code.
With these features enabled, the serdes and PCIe driver including the
Intel E1000 driver can be tested on the Octeon EBB7304.
This patch adds the PCIe host controller driver for MIPS Octeon II/III.
The driver mainly consist of the PCI config functions, as all of the
complex serdes related port / lane setup, is done in the serdes / pcie
code available in the "arch/mips/mach-octeon" directory.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Aaron Williams [Fri, 11 Dec 2020 16:06:10 +0000 (17:06 +0100)]
mips: octeon: octeon_ebb7304: Add board specific QLM init code
This patch adds the board specific QLM/DLM init code to the Octeon 3 EBB7304 board. The configuration of each port is read from the
environment exactly as done in the 2013 U-Boot version to keep the
board and it's configuration compatible.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Fri, 11 Dec 2020 16:06:07 +0000 (17:06 +0100)]
mips: octeon: Makefile: Enable building of the newly added C files
This patch adds the newly added C files to the Makefile to enable
compilation. This is done in a separate step, to not introduce build
breakage while adding the single files with potentially missing
externals.
Aaron Williams [Fri, 11 Dec 2020 16:06:02 +0000 (17:06 +0100)]
mips: octeon: Add cvmx-helper.c
Import cvmx-helper.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:06:01 +0000 (17:06 +0100)]
mips: octeon: Add cvmx-helper-util.c
Import cvmx-helper-util.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:06:00 +0000 (17:06 +0100)]
mips: octeon: Add cvmx-helper-jtag.c
Import cvmx-helper-jtag.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:59 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-helper-fdt.c
Import cvmx-helper-fdt.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:58 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-helper-cfg.c
Import cvmx-helper-cfg.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Fri, 11 Dec 2020 16:05:56 +0000 (17:05 +0100)]
mips: octeon: Misc changes required because of the newly added headers
With the newly added headers and their restructuring (which macro is
defined where), some changes in the already existing Octeon files are
necessary. This patch makes the necessary changes.
Aaron Williams [Fri, 23 Apr 2021 17:56:32 +0000 (19:56 +0200)]
mips: octeon: Add misc remaining header files
Import misc remaining header files from 2013 U-Boot. These will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Aaron Williams [Fri, 11 Dec 2020 16:05:54 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-sso-defs.h header file
Import cvmx-sso-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:53 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-sriox-defs.h header file
Import cvmx-sriox-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-sriomaintx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:51 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-smix-defs.h header file
Import cvmx-smix-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:50 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-sli-defs.h header file
Import cvmx-sli-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:49 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-sata-defs.h header file
Import cvmx-sata-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:48 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-rst-defs.h header file
Import cvmx-rst-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:47 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-pow-defs.h header file
Import cvmx-pow-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:46 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-pko-defs.h header file
Import cvmx-pko-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:45 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-pki-defs.h header file
Import cvmx-pki-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:44 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-pip-defs.h header file
Import cvmx-pip-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:43 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-pepx-defs.h header file
Import cvmx-pepx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:42 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-pemx-defs.h header file
Import cvmx-pemx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:41 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-pcsx-defs.h header file
Import cvmx-pcsx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:40 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-pciercx-defs.h header file
Import cvmx-pciercx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:39 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-pcieepx-defs.h header file
Import cvmx-pcieepx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:38 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-npi-defs.h header file
Import cvmx-npi-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:37 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-mio-defs.h header file
Import cvmx-mio-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:36 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-l2c-defs.h header file
Import cvmx-l2c-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:35 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-ipd-defs.h header file
Import cvmx-ipd-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:34 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-gserx-defs.h header file
Import cvmx-gserx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:33 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-gmxx-defs.h header file
Import cvmx-gmxx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:32 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-fpa-defs.h header file
Import cvmx-fpa-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:31 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-dtx-defs.h header file
Import cvmx-dtx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:30 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-dpi-defs.h header file
Import cvmx-dpi-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:29 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-dbg-defs.h header file
Import cvmx-dbg-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:28 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-ciu-defs.h header file
Import cvmx-ciu-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:27 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-bgxx-defs.h header file
Import cvmx-bgxx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:26 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-asxx-defs.h header file
Import cvmx-asxx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:25 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-agl-defs.h header file
Import cvmx-agl-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:24 +0000 (17:05 +0100)]
mips: octeon: Add misc cvmx-helper header files
Import misc cvmx-helper header files from 2013 U-Boot. They will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Fri, 12 Mar 2021 08:48:25 +0000 (09:48 +0100)]
mmc: octeontx_hsmmc: Add support for MIPS Octeon
Until now, the Octeontx MMC driver did only support the ARM Octeon
TX/Tx2 platforms. This patch adds support for the MIPS Octeon platform
to this driver. Here a short summary of the changes:
- Enable driver compilation for MIPS Octeon, including the MMC related
header file
- Reorder header inclusion
- Switch to using the clk framework to get the input clock
- Remove some functions for MIPS Octeon, as some registers don't
exist here
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Peng Fan <peng.fan@nxp.com> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Horatiu Vultur [Wed, 10 Mar 2021 08:31:39 +0000 (09:31 +0100)]
net: jr2: Fix Serdes6G configuration
Sometimes no traffic was getting out on the ports, the root cause was
a wrong configuration of the Serdes6G, which is used on jr2 pcb111.
This patch fixes this issue by applying the correct configuration.
regmap_read() only fills the first two bytes of val. The last two bytes are
random data from the stack. This means the test will fail randomly.
For low endian systems we could simply initialize val to 0 and get correct
results. But tests should not depend on endianness. So let's use a pointer
conversion instead.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
toradex: configblock: fix module revision in config block
U-boot might display wrong module revision information
for modules with an assembly version 'K'. "cfgblock create"
does not takes into account all revision digits from PID8.
This fix takes into account all digits of PID8
to store module revision.
Igor Opaniuk [Wed, 31 Mar 2021 23:01:53 +0000 (02:01 +0300)]
psci: add features/reset2 support
Adds support for:
* PSCI_FEATURES, which was introduced in PSCI 1.0. This provides API
that allows discovering whether a specific PSCI function is implemented
and its features.
* SYSTEM_RESET2, which was introduced in PSCI 1.1, which extends existing
SYSTEM_RESET. It provides support for vendor-specific resets, providing
reset_type as an additional param.
For additional details visit [1].
Implementations of some functions were borrowed from Linux PSCI driver
code [2].
Andre Przywara [Mon, 12 Apr 2021 00:04:54 +0000 (01:04 +0100)]
arm: highbank: Do DRAM init from DT
So far U-Boot was hard coding a (surely sufficient) memory size of 512
MB, even though all machines out there have at least 4GB of DRAM.
Since U-Boot uses its memory knowledge to populate the EFI memory map,
we are missing out here, at best losing everything beyond 4GB on Midway
boxes (which typically come with 8GB of DRAM).
Since the management processor populated the DT memory node already with
the detected DRAM size and configuration, we use that to populate
U-Boot's memory bank information, which is the base for the UEFI memory
map.
This finally allows us to get rid of the NR_DRAM_BANKS=0 hack, that we
had in place to avoid U-Boot messing up the DT memory node before
loading the kernel.
Also, to cover the whole of memory, we need to enable PHYS_64BIT.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Mon, 12 Apr 2021 00:04:53 +0000 (01:04 +0100)]
arm: highbank: Remove artificial SDRAM size
So far we were defining a somewhat confusing PHYS_SDRAM_1_SIZE variable,
which originally was only used for setting the memtest boundaries. This
definition in highbank.h has been removed about a year ago (moved to
Kconfig), so we also don't need the hard-coded size definition any longer.
Get rid of the misleading memory size definition, which was actually wrong
anyway (it's 4088 MB for those machines with just 4GB of DRAM).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Mon, 12 Apr 2021 00:04:52 +0000 (01:04 +0100)]
net: calxedagmac: Convert to DM_ETH
To squash that nasty warning message and make better use of the newly
gained OF_CONTROL feature, let's convert the calxedagmac driver to the
"new" driver model.
The conversion is pretty straight forward, mostly just adjusting the
use of the involved data structures.
The only actual change is the required split of the receive routine into
a receive and free_pkt part.
Also this allows us to get rid of the hardcoded platform information and
explicit init calls.
This also uses the opportunity to wrap the code decoding the MMIO
register base address, to make it safe for using PHYS_64BIT later.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Andre Przywara [Mon, 12 Apr 2021 00:04:51 +0000 (01:04 +0100)]
arm: highbank: Enable OF_CONTROL
All Calxeda machines are actually a poster book example of device tree
usage: the DT is loaded from flash by the management processor into
DRAM, the memory node is populated with the detected DRAM size and this
DT is then handed over to the kernel.
So it's a shame that U-Boot didn't participate in this chain, but
fortunately this is easy to fix:
Define CONFIG_OF_CONTROL and CONFIG_OF_BOARD, and provide a trivial
function to tell U-Boot about the (fixed) location of the DTB in DRAM.
Then enable DM_SERIAL, to let the PL011 driver pick up the UART platform
data from the DT. Also define AHCI, to bring this driver into the driver
model world as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Mon, 12 Apr 2021 00:04:50 +0000 (01:04 +0100)]
arm: highbank: Limit FDT and initrd load addresses
So far on Highbank/Midway machines U-Boot only ever uses 512MB of DRAM,
even though the machines have typically 4GB and 8GB, respectively.
That means that so far we didn't need an extra limit for placing the DTB
and initrd, as the 512MB are lower than the kernel's limit ("lowmem",
typically 768MB).
With U-Boot now needing to learn about the actual memory size (to
correctly populate the EFI memory map), it might relocate fdt and initrd
to the end of DRAM, which is out of reach of the kernel.
So add limiting values to the fdt_high and initrd_high environment
variables, to prevent U-Boot from using too high addresses.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Anatop is an integrated regulator inside i.MX6 SoC.
There are 3 digital regulators which controls PU, CORE (ARM), and SOC.
And 3 analog regulators which controls 1P1, 2P5, 3P0 (USB).
This patch adds the Anatop regulator driver.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org> Reviewed-by: Sean Anderson <sean.anderson@seco.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: Peng Fan <peng.fan@nxp.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Trying to compile with CONFIG_CMD_MMC=y and CONFIG_MMC=n leads to errors:
riscv64-linux-gnu-ld.bfd: cmd/built-in.o: in function `do_mmcops':
cmd/mmc.c:984: undefined reference to `get_mmc_num'
riscv64-linux-gnu-ld.bfd: cmd/built-in.o: in function `do_mmc_setdsr':
cmd/mmc.c:873: undefined reference to `find_mmc_device'
Add missing dependency.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
projects / u-boot.git / log
;st=author){kind=link}
