Patrick Delaunay [Tue, 29 Jun 2021 10:01:07 +0000 (12:01 +0200)]
arm: dts: stm32mp15: alignment with v5.13
Device tree alignment with Linux kernel v5.13
- ARM: dts: stm32: Add PTP clock to Ethernet controller
- ARM: dts: stm32: enable the analog filter for all I2C nodes in
stm32mp151
- ARM: dts: stm32: fix usart 2 & 3 pinconf to wake up with flow control
- ARM: dts: stm32: Add wakeup management on stm32mp15x UART nodes
- ARM: dts: stm32: add #clock-cells property to usbphyc node on stm32mp151
- ARM: dts: stm32: Add STM32MP1 I2C6 SDA/SCL pinmux
- ARM: dts: stm32: Rename mmc controller nodes to mmc@
- ARM: dts: stm32: Add additional init state for SDMMC1 pins
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Patrick Delaunay [Mon, 28 Jun 2021 12:56:03 +0000 (14:56 +0200)]
stm32mp: cmd_stm32key: add subcommand close
The expected sequence to close the device
1/ Load key in DDR with any supported load command
2/ Update OTP with key: STM32MP> stm32key read <addr>
At this point the device is able to perform image authentication but
non-authenticated images can still be used and executed.
So it is the last moment to test boot with signed binary and
check that the ROM code accepts them.
3/ Close the device: only signed binary will be accepted !!
STM32MP> stm32key close
Warning: Programming these OTP is an irreversible operation!
This may brick your system if the HASH of key is invalid
This command should be deactivated by default in real product.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Patrick Delaunay [Mon, 28 Jun 2021 12:56:00 +0000 (14:56 +0200)]
stm32mp: cmd_stm32key: lock of PKH OTP after fuse
Lock the OTP value of key's hash after the command
$> stm32key fuse <address>
This operation forbids a second update of these OTP as they are
ECC protected in BSEC: any update of these OTP with a different value
causes a BSEC disturb error and the closed chip will be bricked.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Patrick Delaunay [Mon, 28 Jun 2021 12:44:33 +0000 (14:44 +0200)]
stm32mp: stm32prog: fix the content of short help message
Reduce the content of short help message for stm32prog command and
removed the carriage return to fix the display of 'help' command when
this command is activated.
Fixes: 954bd1a923a6 ("stm32mp: add the command stm32prog") Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Patrick Delaunay [Mon, 28 Jun 2021 12:42:08 +0000 (14:42 +0200)]
configs: stm32mp1: remove splashimage and add fdtoverlay_addr_r
Add the variable used by PXE command for fdtoverlays support
since the commit 69076dff2284 ("cmd: pxe: add support for FDT overlays").
Reused the unused "splashimage" address as CONFIG_SPLASH_SOURCE and
CONFIG_VIDEO_LOGO are not activated and U-Boot display the "BACKGROUND"
image found in extlinux.conf to manage splashscreen on stm32mp1 boards.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Simon Glass [Sun, 11 Jul 2021 03:15:21 +0000 (21:15 -0600)]
x86: Ensure the e820 map is installed in all cases
This is a revert of a recent logic change in setup_zimage(). We do
actually need to install this information always. Change it to install
from the Coreboot tables if available, else the normal source.
Fixes: e7bae8283fe ("x86: Allow installing an e820 when booting from coreboot") Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 27 Jun 2021 23:51:10 +0000 (17:51 -0600)]
dtoc: Check that a parent is not missing
With of-platdata-inst we want to set up a reference to each devices'
parent device, if there is one. If we find that the device has a parent
(i.e. is not a root node) but it is not in the list of devices being
written, then we cannot create the reference.
Report an error in this case, since it indicates that the parent node
is either missing a compatible string, is disabled, or perhaps does not
have any properties because it was not tagged for SPL.
Simon Glass [Sun, 27 Jun 2021 23:51:09 +0000 (17:51 -0600)]
x86: cros: Check ROM exists before building vboot
All the x86 devicetree files are built at once, whichever board is
actually being built. If coreboot is the target build, CONFIG_ROM_SIZE
is not defined and samus cannot build Chromium OS verified boot. Add
this condition to avoid errors about CONFIG_ROM_SIZE being missing.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Simon Glass [Sun, 27 Jun 2021 23:51:08 +0000 (17:51 -0600)]
x86: coreboot: Document the memory map
Add information about memory usage when U-Boot is started from coreboot.
This is useful when debugging. Also, since coreboot takes a chunk of
memory in the middle of SDRAM for use by PCI devices, it can help avoid
overwriting this with a loaded kernel by accident.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 27 Jun 2021 23:51:07 +0000 (17:51 -0600)]
x86: coreboot: Use vendor in the Kconfig
Use VENDOR_COREBOOT instead of TARGET_COREBOOT so we can have multiple
coreboot boards, sharing options. Only SYS_CONFIG_NAME needs to be
defined TARGET_COREBOOT.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 27 Jun 2021 23:51:05 +0000 (17:51 -0600)]
x86: coral: Allow booting from coreboot
Set up coral so that it can boot from coreboot, even though it is a
bare-metal build. This helps with testing since the same image can be used
in both cases.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 27 Jun 2021 23:51:03 +0000 (17:51 -0600)]
x86: Do cache set-up by default when booting from coreboot
A recent change to disable cache setup when booting from coreboot
assumed that this has been done by SPL. The result is that for the
coreboot board, the cache is disabled (in start.S) and never
re-enabled.
If the cache was turned off, as it is on boards without SPL, we should
turn it back on. Add this new condition.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 27 Jun 2021 23:51:02 +0000 (17:51 -0600)]
x86: Update the MP constants to avoid conflicts
These constants conflict with error codes returned by the MP
implementation when something is wrong. In particular, mp_first_cpu()
returns MP_SELECT_BSP when running without multiprocessing enabled.
Since this is -2, it is interpreted as an error by callers, which
expect a positive CPU number for the first CPU.
Correct this by using a different range for the pre-defined CPU
numbers, above zero and out of the range of possible CPU values. For
now it is safe to assume there are no more than 64K CPUs.
This fixes the 'mtrr' command when CONFIG_SMP is not enabled.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 27 Jun 2021 23:51:01 +0000 (17:51 -0600)]
x86: Don't set up MTRRs if previously done
When starting U-Boot from a previous-stage bootloader we presumably don't
need to set up the variable MTRRs. In fact this could be harmful if the
existing settings are not what U-Boot uses.
Skip that step in this case.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 27 Jun 2021 23:50:59 +0000 (17:50 -0600)]
spi: ich: Don't require the PCH
When booting from coreboot we may not have a PCH driver available. The
SPI driver can operate without the PCH but currently complains in this
case. Update it to continue to work normally. The only missing feature
is memory-mapping of SPI-flash contents, which is not essential.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Simon Glass [Sun, 27 Jun 2021 23:50:57 +0000 (17:50 -0600)]
x86: pci: Allow binding of some devices before relocation
At present only bridge devices are bound before relocation, to save space
in pre-relocation memory. In some cases we do actually want to bind a
device, e.g. because it provides the console UART. Add a devicetree
binding to support this.
Use the PCI_VENDEV() macro to encode the cell value. This is present in
U-Boot but not used, so move it to the binding header-file.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 27 Jun 2021 23:50:56 +0000 (17:50 -0600)]
pci: Use const for pci_find_device_id() etc.
These functions don't modify the device-ID struct that is passed in, so
mark the argument as const, so the data structure can be declared that
way. This allows it to be placed in the rodata section.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
mmc: mmc_get_op_cond: Allow quiet detection of eMMC
Add a new 'quiet' argument to mmc_get_op_cond() function which avoids
printing error message when SD/eMMC card is not detected.
Espressobin and mx6cuboxi boards use this function for detecting presence
of eMMC and therefore it is expected and normal that eMMC does not have to
be connected. So error message "Card did not respond to voltage select!"
should be skipped in this case as it is not an error.
arm: mvebu: Espressobin: Use function mmc_get_op_cond() for detecting eMMC
Use function mmc_get_op_cond() instead of mmc_init() for detecting presence
of eMMC. Documentation for this function says that it could be used to
detect the presence of SD/eMMC when no card detect logic is available.
This function is also used by mx6cuboxi board for detecting presence of eMMC.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Ensure that 'env default -a' always set correct value to $fdtfile, even
when custom user variable is already stored in non-volatile env storage
(means that env_get("fdtfile") call returns non-NULL value).
As default value is now correctly set like if specified at compile time in
CONFIG_EXTRA_ENV_SETTINGS, there is no need to set $fdtfile explicitly via
env_set("fdtfile", ...) call.
So remove wrong skip based on env_get("fdtfile") and then also unneeded
env_set("fdtfile", ...) call.
Fixes: c4df0f6f315c ("arm: mvebu: Espressobin: Set default value for $fdtfile env variable") Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Now that the MTD subsystem properly supports OF partitions of a SPI NOR,
we can enable the MTD command and start using it instead of the
deprecated sf command.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Cc: Stefan Roese <sr@denx.de> Cc: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Marek Behún [Fri, 9 Jul 2021 14:56:13 +0000 (16:56 +0200)]
arm: mvebu: turris_omnia: force 40 MHz speed on SPI NOR
Commit e2e95e5e2542 ("spi: Update speed/mode on change") changed the
boot time on Turris Omnia from ~2.3s to over 8s, due to SPL loading main
U-Boot from SPI NOR at 1 MHz instead of 40 MHz.
This is because the SPL code passes the CONFIG_SF_DEFAULT_SPEED option
to spi_flash_probe(), and with the above commit spi_flash_probe() starts
prefering this parameter instead of the one specified in device-tree.
The proper solution here would probably be to fix the SF subsystem to
prefer the frequency specified in the device-tree, if it is present, but
I am not sure what else will be affected on other boards with such a
change. So until then we need a more simple fix.
Since the CONFIG_SF_DEFAULT_SPEED option is used by the code, put the
correct value there for Turris Omnia. Also put the correct value to
CONFIG_SF_DEFAULT_MODE and use 40 MHz when reading environment.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Cc: Stefan Roese <sr@denx.de> Cc: Tom Rini <trini@konsulko.com> Cc: Marek Vasut <marex@denx.de> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Cc: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
arm: a37xx: pci: Optimize a3700_fdt_fix_pcie_regions() when fixup offset is zero
If fixup offset is zero then there is nothing to fix. All calculation in
this case just increase addresses by value zero which results in identity.
So in this case skip whole fixup re-calculation as it is not needed.
This is just an optimization for special case when fix_offset is zero which
skips code path which does only identity operations (meaning nothing). No
functional changes.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Konstantin Porotchkin <kostap@marvell.com> Reviewed-by: Stefan Roese <sr@denx.de>
arm: a37xx: pci: Extend validation for PCIe resources and oubound windows
Remapped address of PCIe outbound window may have set only bits from the
mask. Add additional check that remapped address which is calculated from
PCIe bus address specified in DTS file is valid.
Remove also useless clearing of low 16 bits in win_mask. As win_size is
power of two and is at least 0x10000 it means that it always has zero low
16 bits.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Konstantin Porotchkin <kostap@marvell.com> Reviewed-by: Stefan Roese <sr@denx.de>
Tom Rini [Mon, 21 Jun 2021 20:14:18 +0000 (16:14 -0400)]
scripts/get_default_envs.sh: Update for thin archive support
This script was broken by the change to default archives for linking.
This is due to objcopy specifically disallowing copying of thin
archives. To fix this and re-support external users of this script,
switch to using the same logic the u-boot-initial-env make target uses
to dump the section from the object file.
Reported-by: Jan Kiszka <jan.kiszka@web.de> Fixes: 958f2e57eff7 ("build: use thin archives instead of incremental linking") Signed-off-by: Tom Rini <trini@konsulko.com>
Joel Stanley [Fri, 18 Jun 2021 02:05:59 +0000 (11:35 +0930)]
Makefile: Conditionally add defaultenv_h to envtools target
When building the envtools target with CONFIG_USE_DEFAULT_ENV_FILE=y,
the tools require generated/defaultenv_autogenerated.h.
In file included from tools/env/fw_env.c:126:
include/env_default.h:115:10: fatal error: generated/defaultenv_autogenerated.h: No such file or directory
115 | #include "generated/defaultenv_autogenerated.h"
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Tom Rini [Thu, 17 Jun 2021 22:07:25 +0000 (18:07 -0400)]
kconfig / kbuild: Re-sync with Linux 4.20
Align Kconfig and Kbuild logic to Linux 4.20 release with minimal impact
on files outside of this scope.
Our previous Kconfig sync was done by commit 587e4a429698 ("kconfig /
kbuild: Re-sync with Linux 4.19").
As part of this re-sync, a few related changes from previous Linux
releases were found to have been missed and merged in, and are not in
the following list.
The imported Linux commits are:
[From prior to v4.19] b1e0d8b70fa3 kbuild: Fix gcc -x syntax a4353898980c kconfig: add CC_IS_GCC and GCC_VERSION 469cb7376c06 kconfig: add CC_IS_CLANG and CLANG_VERSION
[From v4.19 to v4.20] 487c7c7702ab kbuild: prefix Makefile.dtbinst path with $(srctree) unconditionally 0d91bf584fe5 kbuild: remove old check for CFLAGS use 25815cf5ffec kbuild: hide most of targets when running config or mixed targets 00d78ab2ba75 kbuild: remove dead code in cmd_files calculation in top Makefile 23066c3f4e21 Compiler Attributes: enable -Wstringop-truncation on W=1 (gcc >= 8) 37c8a5fafa3b kbuild: consolidate Devicetree dtb build rules 80463f1b7bf9 kbuild: add --include-dir flag only for out-of-tree build 77ec0c20c7e0 kbuild: remove VERSION and PATCHLEVEL from $(objtree)/Makefile 74bc0c09b2da kbuild: remove user ID check in scripts/mkmakefile 4fd61277f662 kbuild: do not pass $(objtree) to scripts/mkmakefile 80d0dda3a4e5 kbuild: simplify command line creation in scripts/mkmakefile fb073a4b473e kbuild: add -Wno-pointer-sign flag unconditionally 9df3e7a7d7d6 kbuild: add -Wno-unused-but-set-variable flag unconditionally 69ea912fda74 kbuild: remove unneeded link_multi_deps 7d0ea2524202 kbuild: use 'else ifeq' for checksrc to improve readability 04c459d20448 kconfig: remove oldnoconfig target 0085b4191f3e kconfig: remove silentoldconfig target 3f80babd9ca4 kbuild: remove unused cc-fullversion variable 2cd3faf87d2d merge_config.sh: Allow to define config prefix 076f421da5d4 kbuild: replace cc-name test with CONFIG_CC_IS_CLANG 6bbe4385d035 kconfig: merge_config: avoid false positive matches from comment lines
[From post v4.20] 885480b08469 Makefile: Move -Wno-unused-but-set-variable out of GCC only block
There are a number of changes related to additional warnings as well as
being able to drop cc-name entirely that have been omitted for now as
additional work is required first.
Cc: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Tom Rini <trini@konsulko.com>
Trevor Woerner [Tue, 15 Jun 2021 07:30:29 +0000 (03:30 -0400)]
get_maintainer.pl: update from Linux kernel v5.13-rc6
Update U-Boot's version of scripts/get_maintainer.pl to sync it up with the
latest changes to the Linux kernel's version of the same script.
The last sync was with Linux kernel version v4.16. The commits to the kernel's
get_maintainer.pl since then (starting with the most recent) are:
6343f6b71f83 get_maintainer: exclude MAINTAINERS file(s) from --git-fallback cdfe2d220476 get_maintainer: add test for file in VCS e33c9fe8b80c get_maintainer: fix unexpected behavior for path/to//file (double slashes) 0c78c0137621 get_maintainer: add email addresses from .yaml files 0ef82fcefb99 scripts/get_maintainer.pl: deprioritize old Fixes: addresses ef0c08192ac0 get_maintainer: remove uses of P: for maintainer name 2f5bd343694e scripts/get_maintainer.pl: add signatures from Fixes: <badcommit> lines in commit message 49662503e8e4 get_maintainer: add ability to skip moderated mailing lists 0fbd75fd7fee get_maintainer: allow option --mpath <directory> to read all files in <directory> 5f0baf95b1ed get_maintainer.pl: add -mpath=<path or file> for MAINTAINERS file location 31bb82c9caa9 get_maintainer: allow usage outside of kernel tree 0455c74788fd get_maintainer: improve patch recognition 882ea1d64eb3 scripts: use SPDX tag in get_maintainer and checkpatch
Ming Liu [Mon, 31 May 2021 07:04:51 +0000 (09:04 +0200)]
tools: image-host: fix wrong return value
The return value '-ENOSPC' of fit_set_timestamp function does not match
the caller fit_image_write_sig's expection which is '-FDT_ERR_NOSPACE'.
Fix it by not calling fit_set_timestamp, but call fdt_setprop instead.
This fixes a following mkimage error:
| Can't write signature for 'signature@1' signature node in
| 'conf@imx6ull-colibri-wifi-eval-v3.dtb' conf node: <unknown error>
| mkimage Can't add hashes to FIT blob: -1
Signed-off-by: Ming Liu <liu.ming50@gmail.com> Tested-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Rasmus Villemoes [Thu, 20 May 2021 10:32:17 +0000 (12:32 +0200)]
fixdep: remove leftover handling of IS_BUILTIN/IS_MODULE
I removed CONFIG_IS_BUILTIN and CONFIG_IS_MODULE in commit 7d78a4547d ("linux/kconfig.h: remove unused helper macros"), but
fixdep.c still looks for those. It's harmless, but also pointless and
possibly confusing to a future reader.
Yann Dirson [Tue, 18 May 2021 08:59:04 +0000 (10:59 +0200)]
mkimage: allow -l to work on block devices on Linux
When "mkimage -l" was run on a block device it would fail with
erroneous message, because fstat reports a size of zero for those:
mkimage: Bad size: "/dev/sdb4" is not valid image
This patch identifies the "is a block device" case and reports it as
such, and if it knows how to determine the size of a block device on
the current OS, proceeds.
As shown in
http://www.mit.edu/afs.new/sipb/user/tytso/e2fsprogs/lib/blkid/getsize.c
this is no portable task, and I only handled the case of a modern
Linux kernel, which is what I can test.
Stephan Gerhold [Thu, 8 Jul 2021 18:33:50 +0000 (20:33 +0200)]
usb: musb-new: Add glue driver for ST-Ericsson Ux500
The ST-Ericsson DB8500 SoC contains a MUSB OTG controller which
supports both host and gadget mode. For some reason there is
nothing special about it - add a simple glue driver for Ux500
that literally just sets up MUSB together with a generic PHY.
There are no SoC-specific registers etc needed to make USB work.
The new Ux500 glue driver is only tested to work with DM_USB
and DM_USB_GADGET. Both host and gadget mode work fine on
the u8500 "stemmy" board that is already present in U-Boot.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Stephan Gerhold [Thu, 8 Jul 2021 18:33:49 +0000 (20:33 +0200)]
phy: Add driver for ST-Ericsson AB8500 USB PHY
The AB8500 PMIC contains an USB PHY that needs to be set up in
device or host mode to make USB work properly. Add a simple driver
for the generic PHY uclass that allows enabling it.
The if (CONFIG_IS_ENABLED(USB_MUSB_HOST)) might be a bit strange.
The USB PHY must be configured in either host or device mode and
somehow the USB PHY driver must be made aware of the mode.
Actually, the MUSB driver used together with this PHY does not
support dynamic selection of host/device mode in U-Boot at the moment.
Therefore, one very simple approach that works fine is to select
the mode to configure at compile time. When the MUSB driver is
configured in host mode the PHY is configured in host mode, and
similarly when the MUSB driver is configured in device/gadget mode.
Stephan Gerhold [Thu, 8 Jul 2021 18:33:48 +0000 (20:33 +0200)]
power: pmic: Add driver for ST-Ericsson AB8500 via PRCMU
All devices based on ST-Ericsson Ux500 use a PMIC similar to AB8500
(Analog Baseband). There is AB8500, AB8505, AB9540 and AB8540
although in practice only AB8500 and AB8505 are relevant since the
platforms with AB9540 and AB8540 were cancelled and never used in
production.
In general, the AB8500 PMIC uses I2C as control interface, where the
different register banks are represented as separate I2C devices.
However, in practice AB8500 is always connected to a special I2C bus
on the DB8500 SoC that is controlled by the power/reset/clock
management unit (PRCMU) firmware.
Add a simple driver that allows reading/writing registers of the
AB8500 PMIC. The driver directly accesses registers from the PRCMU
parent device (represented by syscon in U-Boot). Abstracting it
further (e.g. with the i2c uclass) would not provide any advantage
because the PRCMU I2C bus is always just connected to AB8500 and
vice-versa.
The ab8500.h header is mostly taken as-is from Linux (with some
minor adjustments) to allow using similar code in both Linux and
U-Boot.
Stephan Gerhold [Wed, 7 Jul 2021 10:58:55 +0000 (12:58 +0200)]
board: stemmy: Copy atags for booting downstream/vendor kernel
The U-Boot "stemmy" board is mainly intended to simplify booting
mainline Linux on various smartphones from Samsung based on ST-Ericsson
Ux500. While the mainline kernel is working great, there are still some
features missing there. In particular, it is currently not possible to
charge the battery when using the mainline kernel.
This means that it is still necessary to boot the downstream/vendor
kernel from Samsung sometimes to charge the device. That kernel is
ancient, still uses board files + ATAGS instead of device trees and
relies on a strange very long kernel command line hardcoded in the
Samsung bootloader.
Actually, since mainline is booted with device trees there is a very
simple way to make the old downstream kernel work as well: We can
simply take most of the ATAGS passed to U-Boot from the Samsung
bootloader and copy them as-is when booting a kernel without device
tree. That way the long command line and other needed ATAGS are copied
as-is without having to bother with them.
The only exception is the ATAG_INITRD - since the initrd is loaded
by U-Boot, the atag for that should be generated in U-Boot so it points
to the correct address. All other ATAGS are copied as-is and not
generated in U-Boot.
Also use the chance and provide a serial# for U-Boot by parsing the
ATAG_SERIAL that is also passed by the Samsung bootloader.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Stephan Gerhold [Wed, 7 Jul 2021 10:58:54 +0000 (12:58 +0200)]
board: stemmy: Parse atags to get available memory
At the moment the "stemmy" board attempts to detect the RAM size with
a simple memory test (get_ram_size()). Unfortunately, this does not work
correctly for devices with 768 MiB RAM (e.g. Samsung Galaxy Ace 2
(GT-I8160), "codina"). Reading/writing memory after the 768 MiB RAM
succeeds but actually overwrites some earlier parts of the memory.
For U-Boot this does not result in any major problems, but on Linux
this will eventually lead to strange crashes because of the memory
corruption.
Since the "stemmy" U-Boot port is designed to be chainloaded from
the original Samsung bootloader, the most reliable way to get the
available amount of RAM is to look at the ATAGS passed by the Samsung
bootloader. Fortunately, the header used to generate ATAGS in U-Boot
(asm/setup.h) can also be easily used to parse them.
Also clarify and simplify stemmy.h a bit to make it more clear where
some of the magic values in there are actually coming from.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Add the device tree for Akebi96. Akebi96 is a 96boards certified
development board based on UniPhier LD20.
( https://www.96boards.org/product/akebi96/ )
Stephan Gerhold [Mon, 5 Jul 2021 12:18:47 +0000 (14:18 +0200)]
arm: mach-snapdragon: pinctrl: Place pin_name in .data section
According to arch/arm/lib/crt0_64.S, the BSS section is "UNAVAILABLE"
and uninitialized before relocation. Also, it overlaps with the
appended DTB before relocation, so writing data into a variable
in the BSS section might corrupt the appended DTB.
Unfortunately, pinctrl-apq8016.c and pinctrl-apq8096.c do place the
"pin_name" variable in the BSS section (since it's uninitialized).
It's also used before relocation, when setting up the pinctrl for
the serial driver.
On DB410c this causes "GPIO_5" to be written into some part of an
appended DTB, e.g.:
Depending on the part of the DTB that is corrupted this might not
cause any problems, but it can also result in strange reboots
without any serial output.
Fortunately, in practice this does not cause issues on DB410c yet
because board_fdt_blob_setup() in dragonboard410c.c currently
overrides the appended DTB with the one passed by the previous
bootloader (LK) (which does not get corrupted).
DB820c does not have board_fdt_blob_setup() so I would expect it to
be affected by this problem. Perhaps everyone was just fortunate to
not compile an U-Boot configuration where the pin_name corrupts an
important part of the DTB.
Make sure "pin_name" is explicitly placed in the .data section
instead of .bss to fix this.
Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Marek Vasut [Sun, 4 Jul 2021 19:32:05 +0000 (21:32 +0200)]
board-info: Call sysinfo_detect() before sysinfo_get_str()
The sysinfo_get_str() implementation checks whether the sysinfo was even
detected. In U-Boot proper, sysinfo_detect() is not called anywhere but
on one specific board. Call sysinfo_detect() before sysinfo_get_str() to
make sure the sysinfo is detected and sysinfo_get_str() returns valid
value instead of -EPERM.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Sun, 4 Jul 2021 19:32:04 +0000 (21:32 +0200)]
board-info: Use sysinfo_get()
Replace uclass_first_device_err(UCLASS_SYSINFO, &dev) with sysinfo_get(&dev).
The board_info code may use sysinfo to print board information, so use the
sysinfo functions consistently. The sysinfo_get() is internally implemented
as return uclass_first_device_err(UCLASS_SYSINFO, &dev) anyway, so there is
no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Sun, 4 Jul 2021 19:31:18 +0000 (21:31 +0200)]
misc: i2c_eeprom: Add atmel,24c01 to the list
Linux kernel binding is using atmel,24c01 compatible string. On the
other hand there is atmel,24c01a which is not listed in the kernel.
Add compatible string without "a" suffix to be compatible with Linux
kernel binding.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Heiko Schocher <hs@denx.de> Cc: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Heiko Schocher <hs@denx.de>
Stephan Gerhold [Fri, 2 Jul 2021 15:06:18 +0000 (17:06 +0200)]
gpio: Add driver for Nomadik GPIO
Nomadik GPIO is a fairly simple GPIO module used in the ST-Ericsson
Ux500 SoCs (and some older Nomadik SoCs). It uses registers where
each GPIO is represented as a single bit, plus "set" and "clear"
registers that allow updating the state without having to read the
existing state.
The driver implements support for it for use together with DM_GPIO
and the existing ste-dbx5x0.dtsi device tree.
Stephan Gerhold [Fri, 2 Jul 2021 15:06:17 +0000 (17:06 +0200)]
gpio: Drop long unused DB8500 GPIO driver
The original U-Boot port for the ST-Ericsson U8500 SoC was dropped
in commit 68282f55b846 ("arm: Remove unused ST-Ericsson u8500 arch").
Most of the drivers related to the old port were removed, but the
db8500_gpio.c driver was forgotten for some reason. There is no way
to select it and it does not compile anymore because of missing
headers, so let's just remove it.
The new port for U8500 introduced in commit 689088f9dae8
("arm: Add support for ST-Ericsson U8500 SoC") fully embraces the
new Driver Model and device trees where possible, so this is
preparation to add a new, simplified GPIO driver based on DM_GPIO.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
efi_loader: Fix to set bootdev_root correctly if bootdev found
Fix find_boot_device() to set bootdev_root if it finds the
bootdev from BootNext. Currently it sets the bootdev_root only
when it finds bootdev from BootOrder.
If multiple capsules are applied, the FMP drivers for the individual
capsules can expect the value of CapsuleLast to be accurate. Hence
CapsuleLast must be updated after each capsule.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tom Rini [Sat, 10 Jul 2021 01:08:52 +0000 (21:08 -0400)]
Merge branch 'master' of https://source.denx.de/u-boot/custodians/u-boot-sunxi
Aside from the usual fixes and updates one visible change is the
MMC update, which fixes some lingering bugs and gives a decent speed
increase on some boards (9->19 MB/s on H6, 21->43 MB/s on A64 eMMC).
I am keeping an watchful eye on bug reports here, to spot any correctness
regressions.
Another change is finally the enablement of the first USB host port on
many boards without micro-USB (data) sockets, like the Pine64 family.
That doubles the number of usable USB ports from 1 to 2 on those boards.
Some smaller fixes, 4GB DRAM support (on the H616) and a new board (ZeroPi)
conclude this first round of changes.
Compile-tested for all 157 sunxi boards, boot-tested on Pine H64,
Pine64-LTS, OrangePi Zero 2 and BananaPi M2 Berry.
Summary:
- DT update for H3/H5/H6
- Enable first USB port on boards without micro-USB
- ZeroPi board support
- 4GB DRAM support for H616 boards
- MMC fixes and speed improvement
- some fixes
Andre Przywara [Wed, 21 Apr 2021 08:33:04 +0000 (09:33 +0100)]
mmc: sunxi: Use mmc_of_parse()
At the moment the Allwinner MMC driver parses the bus-width and
non-removable DT properties itself, in the probe() routine.
There is actually a generic function provided by the MMC framework doing
this job, also it parses more generic properties like broken-cd and
advanced transfer modes.
Drop our own code and call mmc_of_parse() instead, to get all new
features for free.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Andre Przywara [Wed, 5 May 2021 10:33:40 +0000 (11:33 +0100)]
mmc: sunxi: Increase MMIO FIFO read performance
To avoid the complexity of DMA operations (with chained descriptors), we
use repeated MMIO reads and writes to the SD_FIFO_REG, which allows us
to drain or fill the MMC data buffer FIFO very easily.
However those MMIO accesses are somewhat costly, so this limits our MMC
performance, to between 17 and 22 MB/s, but down to 9.5 MB/s on the H6
(partly due to the lower AHB1 frequency).
As it turns out we read the FIFO status register after *every* word we
read or write, which effectively doubles the number of MMIO accesses,
thus effectively more than halving our performance.
To avoid this overhead, we can make use of the FIFO level bits, which are
in the very same FIFO status registers.
So for a read request, we now can collect as many words as the FIFO
level originally indicated, and only then need to update the status
register.
We don't know for sure the size of the FIFO (and it seems to differ
across SoCs anyway), so writing is more fragile, which is why we still
use the old method for that. If we find a minimum FIFO size available on
all SoCs, we could use that, in a later optimisation.
This patch increases the eMMC read speed on a Pine64-LTS from about
22MB/s to 44 MB/s. SD card reads don't gain that much, but with 23 MB/s
we now reach the practical limit for 3.3V SD cards.
On the H6 we double our transfer speed, from 9.5 MB/s to 19.7 MB/s.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Wed, 5 May 2021 08:57:47 +0000 (09:57 +0100)]
mmc: sunxi: Fix MMC clock parent selection
Most Allwinner SoCs which use the so called "new timing mode" in their
MMC controllers actually use the double-rate PLL6/PERIPH0 clock as their
parent input clock. This is interestingly enough compensated by a hidden
"by 2" post-divider in the mod clock, so the divider and actual output
rate stay the same.
Even though for the H6 and H616 (but only for them!) we use the doubled
input clock for the divider computation, we never accounted for the
implicit post-divider, so the clock was only half the speed on those SoCs.
This didn't really matter so far, as our slow MMIO routine limits the
transfer speed anyway, but we will fix this soon.
Clean up the code around that selection, to always use the normal PLL6
(PERIPH0(1x)) clock as an input. As the rate and divider are the same,
that makes no difference.
Explain the hardware differences in a comment.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Thu, 29 Apr 2021 08:31:58 +0000 (09:31 +0100)]
mmc: sunxi: Fix warnings with CONFIG_PHYS_64BIT
When enabling PHYS_64BIT on 32-bit platforms, we get two warnings about
pointer casts in sunxi_mmc.c. Those are related to MMIO addresses, which
are always below 1GB on all Allwinner SoCs, so there is no problem with
anything having more than 32 bits.
Add the proper casts to make it compile cleanly.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Andre Przywara [Fri, 18 Dec 2020 22:02:11 +0000 (22:02 +0000)]
mmc: sunxi: Avoid #ifdefs in delay and width setup
The delay and bus-width setup are slightly different across the
Allwinner SoC generations, and we covered this so far with some
preprocessor conditionals.
Use the more readable IS_ENABLE() instead.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Andre Przywara [Wed, 28 Apr 2021 20:29:55 +0000 (21:29 +0100)]
sunxi: H616: Enable full 4GB of DRAM
The H616 is our first supported Allwinner SoC which goes beyond the 4GB
address space "barrier", by having more than 32 address bits.
Lift the preliminary 3GB DRAM limit for the H616, and update the page
table setup on the way, to actually map that last GB as well.
As not all devices are actually capable of dealing with more than 32
bits (the DMA in the EMAC for instance), we also limit U-Boot's own
DRAM usage to 4GB on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Sun, 25 Apr 2021 23:38:04 +0000 (00:38 +0100)]
sunxi: board: Add H616 MMC2 pins
We hardcode the pinctrl setting for the MMC controllers in boards.c,
since we need them also in the SPL, where there is no DT yet.
Add the respective setting for the H616 SoC, to enable eMMC on boards
with this SoC as well.
Also to make diagnosing this problem easier, print a warning if a board
tries to setup MMC2 pins without a respective SoC setting being defined.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jagan Teki <jagan at amarulasolutions.com> Reviewed-by: Jernej Skrabec <jernej.skrabec at siol.net>
Jernej Skrabec [Mon, 7 Jun 2021 17:42:45 +0000 (19:42 +0200)]
configs: OrangePi PC2: Update defaults
OrangePi PC2 board has DRAM with ODT, so enable it.
H5 SoC is also connected to voltage regulator. It's default value is
reasonable at reset, but might be too low when rebooting with a lower
voltage programmed. In order to avoid instability, enable driver for it
and set it to appropriate voltage.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com> Tested-by: Andre Przywara <andre.przywara@arm.com>
[Andre: remove original ZQ value change, adjust commit message] Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Most clock factors and dividers in the H6 PLLs use a "+1 encoding",
which we were missing on two occasions.
This fixes the MMC clock setup on the H6, which could be slightly off due
to the wrong parent frequency:
mmc 2 set mod-clk req 52000000 parent 1176000000 n 2 m 12 rate 49000000
Also the CPU frequency (PLL1) was a tad too high before.
For PLL5 (DRAM) we already accounted for this +1, but in the DRAM code
itself, not in the bit field macro. Move this there to be aligned with
what the other SoCs and other PLLs do.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
phy: sun4i-usb: Fix PHY0 routing and passby configuration for MUSB
Recent Allwinner platforms (starting with the H3) only use the MUSB
controller for peripheral mode and use HCI for host mode. As a result,
extra steps need to be taken to properly route USB signals to one or
the other. More precisely, the following is required:
* Routing the pins to either HCI/MUSB (controlled by PHY);
* Enabling USB PHY passby in HCI mode (controlled by PMU).
The current code will enable passby for each PHY and reroute PHY0 to
MUSB, which is inconsistent and results in broken USB peripheral support.
Passby on PHY0 must only be enabled when we want to use HCI. Since
host/device mode detection is not available from the PHY code and
because U-Boot does not support changing the mode dynamically anyway,
we can just mux the controller to MUSB if it is enabled and mux it to
HCI otherwise.
This fixes USB peripheral support for platforms with PHY0 dual-route,
especially H3/H5 and V3s.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Tue, 25 May 2021 00:20:25 +0000 (01:20 +0100)]
arm: dts: sunxi: h6: Update DT files
Update the H6 DT files from the Linux 5.12 release.
The changes are minimal (many LED node renames), but also help to enable
USB port 0 in U-Boot (later), enable the RSB device (not yet used in
U-Boot), and also introduce an MMC frequency limit.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
projects / u-boot.git / log
